Defence Statutory Bodies & Commissions/Committees Closing in 16 days TDR #58656705

Tender For Addition/Alteration And Special Repairs To Certain Buildings At Mil Stn Calicut Under Ge (Army) Trivandrum

Issued by Statutory Bodies & Commissions/Committees · Kannur, Kerala
Tender Value
24.19 Lakhs
Estimated cost
Bid Submission
08 Dec 2026
16 days left
EMD
48400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Kannur → Kerala
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Addition/Alteration And Special Repairs To Certain Buildings At Mil Stn Calicut Under Ge (Army) Trivandrum

BOQ

Name of Work:- ADDN/ALTN AND SPECIAL REPAIRS TO CERTAIN BUILDINGS AT MIL STN CALICUT UNDER GE (ARMY) TRIVANDRUM
Sl. No. Item Description
1Dismantling of single layer mangalore pattern or similar tiles in roofing complete all as specified and directed.
2Dismantling of battens for tiles, shingles etc. spacing exceeding 15 cm, of any size, including tilting fillets complete all as specified and directed.
3Dismantling of timber scantlings 40 sqcm and over in section, unframed work, in any position complete all as specified and directed.
4S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 in rafters, purlins etc. complete all as specified and as directed.
5M&L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide/ zinc chrome primer complete all as specified and directed.
6S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.
7S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.
8Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.
9S&F anodised aluminium snap grid frame work (size of grid 605 x 605 mm) including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed.
10M&L for 4 mm thick non-asbestos fibre cement building boards fixed or laid/ inserted to timber/ GI/ aluminium framework with screws in ceiling, flat or sloping complete all as specified and directed.
11M&L for preparation of new surfaces of ceiling and applying two coats of oil bound distemper; over a coat of chalk whiting complete all as specified and as directed.
12Taking down cement or cement lime plaster any description, on brick/ concrete/ stone walls/ ceilings including raking out joints, hacking for key, scrubbing down with water etc. and removing rubbish outside MD land complete all as specified and as directed.
13Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and disposed outside MD land complete all as specified and directed.
14M&L for hardcore of broken stone or boulders, gauge not exceeding 63 mm; deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and as directed.
15M&L for cement concrete 100 mm thick, type D-2, 1:4:8, using 40 mm graded stone aggregate, for sub base of floor etc. finished even and rough to receive top layer complete all as specified and directed.
16M&L for cement concrete 25 mm thick, type B-1, 1:2:4, using 20 mm graded stone aggregate, for flooring etc. finished even and rough to receive top layer complete all as specified and directed.
17M&L for coloured glazed ceramic tiles on vertical surfaces such as skirtings, dados and risers to steps etc., 350 x 250 x 7mm/ 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10 mm thick rendering in cement mortar (1:3) complete all as specified and directed.
18M&L for coloured non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.
19M&L for coloured non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.
20M&L for coloured non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surfaces as in skirting, dado, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick backing coat in cement mortar (1:3) complete all as specified and directed.
21Demolition of brickwork or stone/ boulder masonry built in cement mortar or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and as directed.
22M&L for pre-cast cement concrete block masonry type C1, 1:3:6 (using 20mm graded stone aggregate) with solid blocks exceeding 10 cm in width and setting in CM 1:6 complete all as specified and as directed
23M&L for rendering in two layers as 10 mm thick in cement mortar (1:4) mixed with water proofing compound over rendering 10 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces and finishing the surface fair and even complete all as specified and directed. Note: Water proofing compound will be measured and paid separately.
24M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work/ concrete surfaces, finished even and fair complete all as specified and directed.
25Supply only liquid water proofing compound all as specified and directed.
26Taking down chowkats or frames with shutters any description not exceeding 1.5 sqm each (without taking off shutters from the frame) complete all as specified and directed.
27Taking down chowkats or frames with shutters any description exceeding 1.5 sqm but not exceeding 4 sqm each (without taking off shutters from the frame) complete all as specified and directed.
28S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including preservative treatment complete all as specified and as directed
29M&L for 35 mm thick 2nd class hardwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.
30M&L for 35 mm thick 2nd class hardwood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.
31S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening, complete all as specified and directed.
32S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.
33S&F powder coated aluminium work for doors, windows, ventilators and partitions (fixed portions) (minimum thickness of powder coating 50 micron), with extruded built-up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.; aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and as directed.
34S&F powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows and ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.; aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws including locking system for shutters complete all as specified and as directed.
35S&F 4 mm thick sheet glass, ordinary quality any size and any type of frame and glazing with oil putty (or beading) in square not exceeding 0.5 sqm in each pane complete all as specified and directed.
36S&F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.
37S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.
38S&F 150 mm long aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed.
39S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.
40S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.
41M&L for preparation of new wooden surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
42Taking up or down 20 mm bore steel tubing and connections complete all as specified and directed.
43Taking up or down 25 mm bore steel tubing and connections complete all as specified and directed.
44Supplying, laying and jointing 20 mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 including all necessary pipe fittings such as bends, elbows, tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs etc. fixed complete to walls, ceilings or in floors etc., complete all as specified and directed.
45Supplying, laying and jointing 25 mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 including all necessary pipe fittings such as bends, elbows, tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs etc. fixed complete to walls, ceilings or in floors etc., complete all as specified and directed.
46S&F in repairs vitreous china wash down water closet pan, S and P trap (pedestal pattern), white, including fixing bolt, plastic water closet seat, white or black colour, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage etc. complete all as specified and directed.
47S&F in repairs 10 Litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.
48S&F in repairs wash basin, vitreous china (flat back), size 550 mm x 400 mm, white, including 15 mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated; CI brackets, PVC connections 15mm size with PTMT nuts and of length 450mm, 32 mm dia brass chromium plated waste fittings and 32 mm dia PVC waste pipe including taking down the old existing wash hand basin complete all as specified and directed.
49S&F in repairs 15 mm bore bib taps, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.
50S&F in repairs 15 mm bore bib taps, cast copper alloy chromium plated, fancy type, two in one combination complete all as specified and directed.
51S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.
52S&F PVC connections 15mm size, 450mm length with 02 Nos PTMT nuts with washer etc. complete all as specified and directed.
53S&F in repairs looking mirror, size 600mm x 450mm, bevelled edge, selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.
54S&F in repairs grating square 150 mm size of PTMT (minimum weight 100 gms) complete all as specified and directed.
55S&F in repairs angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for unions and fixed for 15mm bore dia of pipe complete all as specified and directed.
56S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed.
57S&F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.
58S&F in repairs stop valve, cast copper alloy, chromium plated, fancy type, with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for unions or fixed for 15 mm bore dia of pipe complete all as specified and directed.
59Dismantling of cast iron or reinforced concrete drain pipes 75/ 110 mm dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.
60S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.
61S&F 110 mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.
62S&F PVC (SWR) junction, single (single T) equal or unequal for 110 mm bore dia pipe complete all as specified and directed.
63S&F 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.
64S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.
65S&F 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.
66S&F 75mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.
67M&L for PVC (SWR) floor trap, 75 mm dia of outler, plain with grating including jointing with solvent cement taking out old floor trap complete all as specified and directed.
68M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including taking out old gully trap complete all as specified and directed.
69Cutting into existing manholes for connecting new drains, 100 mm internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate, smooth finished, and reforming benching as required complete all as specified and directed.
70Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.
71S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work; confirming to Fe.290.Gde-E-165 complete all as specified and directed.
72Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.
73M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.
74S&F in repairs sink made of stainless steel 1mm thick for kitchen or laboratory, with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.
75M&L for reinforced cement concrete (nominal mix) 1:2:4, type B1 using 20 mm graded stone aggregate, in beams, cantilevers, bresummers, lintels over 1.5 m span complete all as specified and as directed
76M&L for formwork to rough finished flat surfaces of concrete as in sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams complete all as specified and directed.
77M&L for reinforced cement concrete (nominal mix) 1:2:4, type B1 using 20 mm graded stone aggregate, in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.
78M&L for formwork to rough finished flat surfaces of concrete as in soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.
79S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, as in stirrups, spacers and binders including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
80S&F mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, as in stirrups, spacers and binders including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
81M&L for preparation of newly plastered external walls and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied at the rate of 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.
82M&L for preparation of new surfaces of walls and distempering with two coats of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/ Litre, of approved manufacturer, of required shade and colour over and including a coat of chalk whitening primer complete, as per manufacturer's specifications complete all as specified and directed.
83M&L for complete removal of existing treatment on external walls and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied at the rate of 0.90 litre/ 10 sqm complete all as specified and directed.
84M&L for complete removal of existing treatment on internal wall surfaces and distempering with two coats of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/ Litre, of approved manufacturer, of required shade and colour over and including a coat of chalk whitening primer complete, as per manufacturer's specifications complete all as specified and directed.
85Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floors, etc. complete all specified and directed.
86Taking down old and unserviceable distribution board any type including sheet metal enclosures, after removing all connections and making good the disturbed surface complete all specified and directed. Please Enable Macros to View BoQ information
87Taking down old and unserviceable distribution board any type including sheet metal enclosures, after removing all connections and making good the disturbed surface complete all specified and directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58656705
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 24.19 Lakhs
LAST DATE 08-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Addition/Alteration And Special Repairs To Certain Buildings At Mil Stn Calicut Under Ge (Army) Trivandrum
Basic Detail
Tender No 8416/E8
Bidding Type Tender
Location
City Kannur
State Kerala
Key Dates
Publish Date 21 Nov 2026
Submission Date 08 Dec 2026
Open Date 10 Dec 2026
Finance
Tender Value 24.19 Lakhs
Tender Fee 500
EMD 48400
Exemption Available
Document List
8416Tender.pdf
a7cdb48f-5da1-4bea-8c4d-2e7ad45c279c.html
BOQ_897389.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 21, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 08, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 16 days
Dec 10, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 18 days

Tender Documents

Download All (ZIP) ↓
pdf

8416Tender.pdf

html

a7cdb48f-5da1-4bea-8c4d-2e7ad45c279c.html

xls

BOQ_897389.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender