Tender For Provision Of Dc Rectifier, Air Compressor And Vaccum Pump For Miscellaneous Instrument Bay At Instrument And Electrical Workshop (P-2) At Nay(K)
Tender Value
43.83 Lakhs
Estimated cost
Bid Submission
12 Dec 2026
20 days left
EMD
87660
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Dc Rectifier, Air Compressor And Vaccum Pump For Miscellaneous Instrument Bay At Instrument And Electrical Workshop (P-2) At Nay(K)
BOQ
| Sl. No. | Item Description |
| 1 | Supply, install, testing and commissioning of 8.5 KW Variable DC Rectifier all as specified as under:- Type : DC POWER SUPPLY, Rating : 30VDC / 285A A. AC INPUT (i) Voltage : 440V AC ± 10%, (ii) Frequency : 50Hz ± 5% (iii) Phase : Three phase 4-wire. B. DC OUTPUT (i) Boost Voltage : 30V DC, (ii) Output Current : 285A Max (iii) Ripple : Not exceeding 5% rms at rated output voltage and current. (iv) Steady state voltage : Not exceeding +/-2% for +/-10% supply regulation fluctuation and 10 to 100% load variation. (v) Output voltage/current stability : Within +/-1% of set value. (vi) Control power circuitry : Three phase full wave full control thyristorised bridge fed thru’ 3 phase double wound transformer and controlled by automatic voltage and current controller unit with current limiting feature C. Measuring Meters : Following Analog Type Meters of 96mm x 96 mm with 90 deg deflection and 1.5% accuracy will be provided in the system for measuring the respective parameters. a. AC Voltmeter with Selector Switch b. DC voltmeter to measure voltages at Output c. DC Ammeter to measure output current D. INDICATIONS : Cluster LED Lamps provided for the following conditions a. AC Main ON (R,Y,B), b. Output DC ON Cluster LED type Annunciation with indication shall be provided for the following conditions a. AC Supply Unhealthy, b. DC Over Current c. DC Under Voltage, d. DC Over Voltage |
| 2 | Note Continued for Item No 1.01E. PROTECTIONS : Following protections will be provided in the system. a. AC Input Circuit Breaker, b. DC Output Circuit Breaker c. Fast acting Semiconductor Fuses for the Rectifier Bridge, d. Phase fail protection, e. Over Current Protection, f. DCPS Current Limit F. SWITCHES & CONTROLS : -Following switches and controls are provided in the systems a. AC Input Circuit Breaker, b. DC Output Circuit Breaker, c. Test, Accept/ Reset Push Buttons, d. Over current reset push buttons G. SPECIAL FEATURES:- a. Soft start on DC side b. Class-F insulation for all Magnetics, c. Automatic Voltage and current Regulation, d. Filter Circuit to limit Ripple, e. DCPS Current Limiting H. GENERAL :-a. Cabinet : Free Standing Steel Cabinet, Easy for Accessing, Installation and Commissioning and Cable Entry at Bottom.b. Colour : RAL 7032 , c. Painting Process : Powdered Coating d. Protection : IP – 20, e. Temperature range : 0 to 50°C of operation f. Relative humidity : 0% to 95% non-condensingg. Cooling : Natural Cooling. Make : Liveline/Aplab/Powerone |
| 3 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded copper conductor of size 16 Sq.mm 4 core complete all as specified and directed by Engr-in-Charge. |
| 4 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded copper conductor of size 16 Sq.mm single core complete all as specified and directed by Engr-in-Charge. |
| 5 | Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and Neutral (SPN) current carrying capacity 63AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engr-in-Charge. |
| 6 | Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and Neutral (SPN) current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engr-in-Charge. |
| 7 | Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engr-in-Charge. |
| 8 | Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engr-in-Charge. |
| 9 | Supply and fixing of Kirloskar make Vaccum pump model DV-50 Suc 50mm X Del 50mm coupled with Kirloskar make 7.5 KW/10 HP ,1450 RPM motor,suitable for air flow rate of 11 m3/hr to 138 m3/hr and 660mm of vaccum in MM of mercury.Make : Kriloskar or Equivalent |
| 10 | Supply and Fixing Star delta Starter fully automatic suitable for 7.5 KW/10 HP 415 V AC vaccum Pump |
| 11 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded copper conductor of size 6 sqmm 3 core complete all as specified and directed by Engr-in-Charge |
| 12 | Supply &Fixing tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors of size 25 mm dia |
| 13 | Supply &Fixing tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors of size 20 mm dia |
| 14 | Supply and fixing Stop valves of size 25 mm dia, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete. |
| 15 | Supply and fixing Stop valves of size 20 mm dia, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete. |
| 16 | Provisioning and installation of Electric powered-screw air compressor system,20 HP air compressor with pneumatic pressure line, Capacity -72 cfm, Maximum pressure -7.2 bar.g, Normal working pressure -7.0 bar.g, Main motor nominal rating- 15kW (20 hp) Normal rating with SF 1.0 Continuous duty, Starter- STAR DELTA, Dimensions- 1356mm*721mm*1220mmWeight of the package- 586 kg SCOPE OF SUPPLY:- Base & Enclosure:- Rigid frame, Powder-coated panels with two service doors at the front and two at the sides, Latches on each door, Ducts for drive motor Drive System:- Main motor – high Efficiency IE3 TEFC motor with \\"class-F\\" insulation,Flexible coupling with elastic element, Rigid connection of motor and the airend flange, CE certified control panel with, Wye-delta reduced voltage starter for the main motor, DOL starter with contactor for cooling motors,High amp protection electric motorsAir Inlet System:Pre-filter: To ensure clean air is supplied to the inlet system- Air duct: To get clean and cool air to the air filter, Air filter housing, Twin paper element, each of 3 microns with an efficiency of 99%, For pre-cleaning on the air cleaner to separate heavy particles and avoid clogging of paper element, Service indicator – indicating filter service need, Rubber coupling connecting air filter to the intake valve, Normally closed type intake valve with integrated blow down and solenoid control valve, Load/unload type capacity control, Intake valve modulation with 100 to 60% capacity control and load/unload below 60% Compression System: Highly efficient axis airend with n-v profile rotors |
| 17 | Note Continued for Item No 15 Air/Oil Separation System:Receiver tank incorporating OSBIC principle mounted on the base frame, Oil filling port, Oil drain with valve, Pressure relief valve, Oil sight glass, Spin-on air-oil separator element / Cartridge type air-oil-separator element, Minimum pressure valve, Discharge System: Moisture separator with zero loss drain valve Cooling System:Thermal zones for hot and cool air for maximized cooling, High ambient oil cooler for low operating temperature, High efficiency after-cooler for low approach temperature, Cooler mounted insulated compartment for easy cleaning, Cooling fan with integrated motorLubrication System:High capacity spin-on oil-filter element with 10-micron rating, Return oil line from separator tank to air-end, Rigid pipe connections for long life and leak-free operationControls System: Neuron III controller, Pressure transducer, Temperature sensor Safety Features:CE certified packageRECEIVER KIT :- Capacity 500 Ltr DRYER KIT :- Capacity 80 cfm PRE FILTER :- Capacity 74 cfm FINE FILTER :- Capacity 74 cfmLaying of pipeline from air compressor to the test benches on ground and first floor is also to be carried out.Make : ELGi or equivalent, |
| 18 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded copper conductor of size 10 sqmm 3 core complete all as specified and directed by Engr-in-Charge |
| 19 | Chemical Earthing with copper earth plate 90cmx60cmx5mm and 32x6mm complete with back filling earth enhancing compound as per IEC 62561-7:2018,connected accessories including copper coppe earth lead 32x6mm by means of bolts,nuts, check nuts and washers of copper and earth strip protected by by GI pipe 50mm dia light grade and connected from earth plate electrode to main switch borad/earthing test point or upto 7.5 mtr whichever is less including inspection /testing chamber and cover /PCC chamber pit in PCC 1:3:6 TYPE C-1,40MM thick pre-cast RCC cover re-inforced with 8mm dia TMT bars@ 10cm C/C on both sides and handle, excavation and earth work in any type of soil and removal upto 50 mtr for special equipments / DB complete all as specified and directed including testing on completion. |
| 20 | Earth continuity conductor or main earthing lead on wall of height up to 40 meter / Ceiling floor by soldering and fixing on porcelain saddles complete all as specified and directed as required 20x3 Copper Strip |
| 21 | M &L for earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 3.15 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by alternate layer of common salt and charcoal 15 cm thick, connected to and including copper earth lead 20x3 mm copper strip by means of bolts, nuts, check nuts and washers of galvenised iron or steel and earth strip protected by GI pipe 40 mm dia light grade and connected from earth plate electrode to main switch board/ earthing test point or upto 7.5 mtr whichever is less including watering arrangement using 20mm GI pipe light grade, MS funnel with wire mesh, PCC chamber pit in PCC 1:3:6 type C-1, 40 mm thick pre-cast RCC cover re-inforced with 8mm dia TMT bars @ 10cm C/C on both sides and handle, excavation and earth work in any type of soil and removal upto 50 mtr complete all as specified and shown in electrical plate No 03 of SSR Part-I, all as specified and directed including testing on completion. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysDec 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender