Housing Urban and Rular Development Government Departments Closing in 27 days TDR #58654180

Tender For Construction Of Proposed Bridge Over Irrigation Canal In Replacement Of Narrow And Old Minor Bridge At 11.43 Km Of Bhatar Banpas Road Under Burdwan North Highway Division In The District Of Purba Bardhaman.

Issued by Government Departments · Purba Bardhaman, West Bengal
Tender Value
18.32 Crore
Estimated cost
Bid Submission
18 Dec 2026
27 days left
EMD
10 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Construction Of Proposed Bridge Over Irrigation Canal In Replacement Of Narrow And Old Minor Bridge At 11.43 Km Of Bhatar Banpas Road Under Burdwan North Highway Division In The District Of Purba Bardhaman.

BOQ

Name of Work:- Construction of proposed bridge over irrigation canal in replacement of narrow and old minor bridge at 11.43 km of Bhatar Banpas Road under Burdwan North Highway Division in the district of Purba Bardhaman.
Sl. No. Item Description
1FOUNDATION WORKS :
2Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material (ReferencetoMORT&H'sspecification 304). By Mechanical MeansDepth upto 3 m (Including cost of dewatering)(Rate is including 1% Cess)
3Bored cast-in-situ M35 grade R.C.C. Pile excluding Reinforcement complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts and lead upto 1000 m (Reference to MORT&H's specifications 1100, 1600 & 1700).Pile diameter = 1000mm Using batching plant(Rate is including 1% Cess)
4Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H'sspecifications1500,1700& 2200). PCC Grade M20 (Including Shuttering)(Rate is including 1% Cess)
5Providing and Constructing Temporary Island 16 m diameter for Construction of Well Foundation for 8m dia. Well (Reference to MORT&H's specification 1200). Assuming depth of water 1.0 m and height of island to be 1.25m.It is assumed that earth will be available within the working space of crane with grab bucket.(Rate is including 1% Cess)
6Reinforced cement concrete in Pile cap complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1114, 1500 & 1700). RCC Grade M35 (Including Shuttering)(Rate is including 1% Cess)
7Supplying, binding, fixing etc. including initial straightening, cutting to requisite length, hooking and bending to correct shape,placing in proper positionof uncoated HYSD reinforcement bar in open founadation complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 1600 & 2200).(Rate is including 1% Cess)
8Pile Load Test on single Vertical Pile in accordance with IS:2911(Part-4) (Reference to MORT&H's specification 1113). a) Initial and routine load test(Rate is including 1% Cess)
9Pile Load Test on single Vertical Pile in accordance with IS:2911(Part-4) (Reference to MORT&H's specification 1113) b) Lateral load test(Rate is including 1% Cess)
10Integrity testing of Pile using Low Strain / Sonic Integrity Test / Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerized equipment and high skill trained personal for conducting the test & submission of results, all complete incluing mobilisation & demobilisation as per direction of Engineer-incharge.b)For Rest of South Zone & West Zone(Rate is including 1% Cess)
11Providing and constructing one span service road to reach island location from one pier location to another pier location(Rate is including 1% Cess)
12Providing Steel Liner 10 mm thick for Curbs and 6 mm thick for Steining of Wells including Fabricating and Setting out as per Detailed Drawing (Reference to MORT&H's specifications 1204 & 1900)(Rate is including 1% Cess)
13SUB STRUCTURES WORKS :
14Plain/Reinforced cement concrete in sub-structure complete all including vibrating and compacting, finishing, curing, sampling, testing etc. by mechanically mixed as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). RCC Grade M35 Height upto 5m(Rate is including 1% Cess)
15Supplying, binding, fixing etc. including initial straightening, cutting to requisite length, hooking and bending to correct shape,placing in proper position of uncoated HYSD reinforcement bar in sub-structure complete asper drawing and Technical Specifications(ReferencetoMORT&H's specifications 1600 & 2200).(Rate is including 1% Cess)
16Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200 in 5th Revision).(Rate is including 1% Cess)
17Back filling behind abutment, wing wall and return wall complete including spriklring water and throughly compacted with plate compactor/power rammer in layers not exceeding 150mm compacted thickness as per drawing and Technical Specification (710.1.4 of IRC:78 & MoRTH's specification 2200)Sandy materials(Rate is including 1% Cess)
18Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRT&H specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification (710.1.4 of IRC:78 & 2200 in 5th Revision).Using 0.72 cum of 26.5 mm Stonechips and 0.48 cum of coarse sand per cum.(Rate is including 1% Cess)
19SUPER STRUCTURES WORKS :
20Furnishing and Placing Reinforced/ Prestressed cement concrete in superstructure all including vibrating and compacting, finishing, curing, sampling, testing etc. by mechanically mixed as per clause 1719 of MoRTH but excluding the cost of materials as per drawing and Technical Specification (Reference to MORT&H's specifications 1500, 1600,1700 & 1800).For T-beam & slabRCC Grade M 35Height upto 5m (Including Shuttering)(Rate is including 1% Cess)
21Supplying, binding, fixing etc. including initial straightening, cutting to requisite length, hooking and bending to correct shape, placing in proper postion of uncoated HYSD reinforcement bar in super-structure complete as per drawing and technical specifications (Reference to MORT&H's specification 1600) .(Rate is including 1% Cess)
22Drainage Spouts not less than100mm dia of corrosive resistance material ,spacing notexceeding10m.complete as per drawing and Technical specification (Reference toMORT&H's specification 2705).(Rate is including 1% Cess)
23Providing and laying of a strip seal expansion joint catering maximum horizontal movement upto 80 mm manufactured by MORT&H ,GOI Approved/Empanelled manufacturer andcompleteasperapproveddrawings and standard specifications to be installed by themanufacturer/supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation (Reference to MORT&H's specification 2606).(Rate is including 1% Cess)
24Providing & fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing & Technical Specification.(Rate is including 1% Cess)
25Providing and fixing in position 20mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans not exceeding 10mtocaterforahorizontalmovement upto 20 mm, covered with sealant completeas per drawing and technical specifications.(Rate is including 1% Cess)
26Reinforced Cement Concrete Crash Barrier : Provision of an Reinforced cement concrete cras hbarrier at the edges of the road, approaches to bridge structures and medians, constructed with M-40 grade concrete with HYSD reinforcement conforming to IRC:21 and dowelbars 25mm dia, 450mm long at expansion joints filledwith pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No.RW/NH-33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer,allasspecified (Reference to MORT&H's specification 811).(Rate is including 1% Cess)
27Construction of precast RCC railing of M30 Grade, aggregate size not exceeding 12 mm, true to line and grade,tolerance of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertical post for expansion, with a minimum 10 days curing complete as per approved drawings and technical specifications (Reference toMORT&H's specifications 2703, 1500, 1600 & 1700).(Rate is including 1% Cess)
28PCC 1:3:6 in Foundation Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days (Reference to MORT&H's specification 2100).(Rate is including 1% Cess)
29Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503)On Cement Concrete Pavement surface @ 0.30kg-0.35 /sqm using Cationic bitumen emulsion RS1 (Bulk) .(Rate is including 1% Cess)
30Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder of approved grade@ 5.2% (min) for Gr.-1 as per table 500-17, and mix design done as per table 500-10 and job mix formula as per cl. 505.3.3 and filler(Cement /hydrated lime / Rock dust ), transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C to achieve the desired compaction as per clause no 507.3.5 complete in all respects ref. to MORTH specification clause No.507. Grading I (19 mm nominal maximum aggregate size) Layer Thickness 50mmUsing Bulk Bitumen VG 40(Rate is including 1% Cess)
31Painting on Concrete SurfacesProviding and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm (Reference to MORT&H's specification 800).(Rate is including 1% Cess)
32Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot appliedthermoplastic compound 2.5 mmthick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes (Reference to MORT&H's specification 803).(Rate is including 1% Cess)
33Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/ Bitumen/ M-Seal etc) complete.A) UPVC Pipes: (iii) 160 mm. Dia.(Rate is including 1% Cess)
34RETAINING WALL WORKS :
35Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, includingsettingout, constructionof shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material (ReferencetoMORT&H'sspecification 304). By Mechanical MeansDepth upto 3 m (Including cost of dewatering)(Rate is including 1% Cess)
36Excavation for StructuresEarth work in excavation of foundation of structures as per drawing and technical specification, includingsettingout, constructionof shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material (ReferencetoMORT&H'sspecification 304). By Mechanical Meansfor Depth 3m to 6m (Including cost of dewatering)(Rate is including 1% Cess)
37Plain/Reinforced cement concrete in open foundation complete allincluding vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500,1700& 2200). PCC Grade M15 (Including Shuttering)(Rate is including 1% Cess)
38Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H'sspecifications1500,1700& 2200). RCC Grade M25 (Including Shuttering)(Rate is including 1% Cess)
39Plain/Reinforced cement concrete in sub-structure complete all including vibrating and compacting, finishing, curing, sampling, testing etc. by mechanically mixed as per drawing and Technical Specifications (ReferencetoMORT&H'sspecifications 1500, 1700 & 2200). RCC Grade M25Height upto 5m (Including Shuttering) (Rate is including 1% Cess)
40Supplying, binding, fixing etc. including initial straightening, cutting to requisite length, hooking and bending to correc tshape, placing in proper positionof uncoated HYSD reinforcement bar in open foundation complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 1600 & 2200).(Rate is including 1% Cess)
41Supplying, binding, fixing etc. including initial straightening, cutting to requisite length, hooking and bending to correc tshape, placing in proper positionof uncoated HYSD reinforcement bar in sub-structure complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 1600 & 2200).(Rate is including 1% Cess)
42Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 2706 & 2200 in 5th Revision).(Rate is including 1% Cess)
43Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRT&H specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification (710.1.4 of IRC:78 & 2200 in 5th Revision).Using 0.72 cum of 26.5 mm Stonechips and 0.48 cum of coarse sand per cum.(Rate is including 1% Cess)
44Sand Filling in Foundation Trenches with good local fine sand free from earth not exceeding 150 mm compacted thickness including inundating each layer by profuse water and porking and rammimg layer by layer. Quality of sand is to be approved by the Engineer-in-charge.(Reference to MORT&H's specification 304).(Rate is including 1% Cess)
45APPROACH ROAD WORKS :
46Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately (Reference to MoRT&H's specification clause 202)By Mechanical MeansBituminous course(Rate is including 1% Cess)
47Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately (Reference to MoRT&H's specification clause 202)By Manual MeansGranular course(Rate is including 1% Cess)
48Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with Disposal upto 1000 metres.: Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m (Reference to MoRT&H's specification clause 301).(Rate is including 1% Cess)
49Sand Filling in Foundation Trenches with good local fine sand free from earth not exceeding 150 mm compacted thickness including inundating each layer by profuse water and porking and rammimg layer by layer. Quality of sand is to be approved by the Engineer-in-charge.(Reference to MORT&H's specification 304).(Rate is including 1% Cess)
50Plant Mix MethodConstruction of granular sub-base by providing graded material such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading spreading in uniform layers with motor grader on prepared surface, mixing by appropriate mechanical mixure (with controlled addition of water), and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401.GSB Grade- V(Rate is including 1% Cess)
51Wet Mix Macadam: Providing, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406.(Rate is including 1% Cess)
52Dense graded bituminous macadam: Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder of approved grade @ 4.0% (min) for Grading -1 and 4.5% (min) for Grading -2 by weight of total mix and filler(Cement /hydrated lime / Rock dust ) as per table 500-10 and mix design done as per table 500- 11and job mix formula as per clause 505.3.3 transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C, and to achieve the desired compaction as per MORT&H specification clause No. 505.3.5 complete in all respects (Reference to MORT&H's specification clause 505) Grading II (26.5 mm nominal maximum aggregate size) Layer Thickness 50 - 75mm Using Bulk Bitumen VG 40(Rate is including 1% Cess)
53Bituminous Concrete: Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder of approved grade @ 5.4% (min) for Gr.-2 , as per table 500-17, and mix design done as per table 500-10 and job mix formula as per cl. 505.3.3 and filler(Cement /hydrated lime / Rock dust ), transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C to achieve the desired compaction as per clause no 507.3.5 complete in all respects ref. to MORTH specification clause No.507. Grading II (13.2 mm nominal maximum aggregate size) Layer Thickness 30 mmUsing Bulk Bitumen VG 40
54Providing and applying Primer coat with cationic bitumen emulsion CSS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502). On WMM/WBM surface @ 0.70-1.0kg /sqm using cationic bitumen emulsion CSS1 grade (Bulk).(Rate is including 1% Cess)
55Providing and applying Tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). On Granular surface treated with primer @ 0.25kg-0.30 /sqm using Cationic bitumen emulsion RS1 (Bulk) .(Rate is including 1% Cess)
56Providing and applying Tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).On bituminous surface @ 0.20kg- 0.3kg /sqm using Cationic bitumen emulsion RS1 (Bulk) .(Rate is including 1% Cess)
57Water Bound Macadam: Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density (Reference to MoRT&H's specification 404).By Manual Means Grading 2Using Screening Crushable type such as Moorum or Gravel(Rate is including 1% Cess)
58Construction of Embankment with Material obtained from Borrow pitsConstruction of embankment with approved material obtained from borrow pits (Earth is available from Govt Land) with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 & 300-1 .The size course material in the mix of earth ordinarily shall not be exceed 75mm.(Reference to MoRT&H's specification clause 305).(Rate is including 1% Cess)
59Cast in Situ Cement Concrete M 20 Kerb with Channel: Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M15 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCCM20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409 (Reference to MORT&H's specification 409).(Rate is including 1% Cess)
60ROAD FURNITURE WORKS :
61Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface: Road Marking with Hot Applied Thermoplastic Compound withReflectorising Glass Beads on Bituminous Surface Providing and laying of hot appliedthermoplastic compound 2.5 mmthick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes (Reference to MORT&H's specification 803).(Rate is including 1% Cess)
62Retro-Reflectorised Traffic Signs :Providing and fixing full Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm 6 mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm. below ground level as per approved drawing (Reference to MORT&H's specification 801 in 5th Revision).(Rate is including 1% Cess)90 cm equilateral triangle
6360 cm equilateral triangle
6460 cm circular
6580cm x 60cm rectangular
6660cm x 60cm Square
67Direction and Place Identification Signs upto 0.9 sqm Size Board : Providing and erecting direction and place identification retro reflectorised sign as per IRC:67made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2mm thick with area not exceeding 0.9 sqmsupported on a mild steel single angle iron post75x 75x6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level asper approved drawing (Reference to MORT&H'sspecification 801).(Rate is including 1% Cess)
68Direction and Place Identification Signs with size more than 0.9 sqm size Board: Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing and Clause 801 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).(Rate is including 1% Cess)
69Road Distance IndicatorReinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc (Reference to MORT&H's specification 805).Ordinary kilometer stone (precast)(Rate is including 1% Cess)
70Metal Beam Crash Barrier Reference to MORT&H's specification 811): Type - A, \\"W\\" : Metal Beam Crash Barrier Providing and erecting a \\"W\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811.(Rate is including 1% Cess)
71Supplying & fixing of Raised Pavement Markers / Road Studs / Cats Eye made of polycarbonate moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face which shall support a load of 13635 kg tested in accordance to ASTM D 4280 Type H and complying to clause no 804 of MoRT&H's specification for Road &Sridge Works (Fifth Rev.). Marker height shall not be less than 10 mm and shall not exceed 20 mm, width shall not exceed 130mm and with minimum reflective area of 13 sq.cm. on each side and slope to the base shall be 35 ± 5 degree. Fixing will be without nails but by using epoxy resin based adhesive as per manufacturer's recommendation including site clearance etc. and complete as directed by the Engineer in Charge .The contractor will have to provide a test certificate from a reputable national/international laboratory conforming the above specifications.(Rate is including 1% Cess)
72Turfing with Sods Furnishing and laying of the live sods of ( thickness 50-80mm) perennial turf forming grass on embankment slope, verges or other locations shown on the drawing or as directed by the engineer including preparation of ground, fetching of sods and watering (Reference to MoRT&H's specification clause 307).(Rate is including 1% Cess)
73FOOTPATH ROAD APPURTENANCES AND ROTARY WORKS :
74Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement, footpath etc. including necessary underlay 25 mm thick [avg] cement mortar (1:3) complete in all respect with all labour and materials. [Using cement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.m for joint filling] Red Variety (ii) 30 mm. thick(Rate is including 1% Cess)
75Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material (ReferencetoMORT&H'sspecification 304). Mechanical MeansDepth upto 3 m (Including cost of dewatering)(Rate is including 1% Cess)
76Earthwork in filling in foundation trenches with good earth in layers not exceeding 15cm. including watering and ramming layer by layer complete with earth obtained from excavation of foundation or from fresh excavation of land arranged by Department within a lead of 150 m.(Rate is including 1% Cess)
77Sand Filling in Foundation Trenches with good local fine sand free from earth not exceeding 150 mm compacted thickness including inundating each layer by profuse water and porking and rammimg layer by layer. Quality of sand is to be approved by the Engineer-in-charge.(Reference to MORT&H's specification 304).(Rate is including 1% Cess)
78Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting,finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). PCC Grade M20 (Including Shuttering) (Rate is including 1% Cess)
79Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting,finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). RCC Grade M25 (Including Shuttering)(Rate is including 1% Cess)
80Supplying, binding, fixing etc. including initial straightening,cutting to requisite length, hooking and bending to correct shape, placing in proper position of uncoated HYSD reinforcement bar in sub-structure complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 1600 & 2200).(Rate is including 1% Cess)
81Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] With 1:4 cement mortar 15 mm thick plaster(Rate is including 1% Cess)
82M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground foor. Grill weighing above 16 Kg./sq.mtr and above.(Rate is including 1% Cess)
83Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor: (b) Two coat(Rate is including 1% Cess)
84Protective and Decorative Textured exterior high class matt finish paint of approved quality, composed of special Tharmoplastic Resin containing fine crystalline additives derive from Granite as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.In Ground Floor: (b) Two coat(Rate is including 1% Cess)
85Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.(Rate is including 1% Cess)
86Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary:On steel or other metal surface : With super gloss (hi-gloss) - (ii) Two coats (white in shade)(Rate is including 1% Cess)
87Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with100mm dia AC/PVC/HDPC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce.Completeasper drawing and Technical Specifications (ReferencetoMORT&H'sspecifications 2706 & 2200).(Rate is including 1% Cess)
88Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRT&H specifications to a thickness of not less than 600mm with smaller size towards thesoil and bigger size towards the wall and provided over the entire surface behind abutment,wing wallandreturn wall to the full height compacted to a firm condition complete as per drawing and Technical Specification (710.1.4 of IRC:78 & 2200).Using 0.72 cum of 26.5 mm Stonechips and 0.48 cum of coarse sand per cum.(Rate is including 1% Cess)
89PCC 1:3:6 in Foundation: Plain cement concrete of 1:3:6 nominal mix with crushed stone aggregate 40 mm nominal maximum size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days as per the requirements of MORT&H's specification 1704.3.(Rate is including 1% Cess)
90Laying Reinforced Cement Concrete Pipe NP4 / Prestressed Concrete Pipe on First Class Bedding in Single Row . Laying Reinforced cement concrete pipe NP4/prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per the requirements of MORT&H's specification 2900. 1000 mm dia(Rate is including 1% Cess)
91Cast in Situ Cement Concrete M 20 Kerb with Channel: Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250mmhigh inM20 grade PCC on M15 grade foundation 150 mm thick, kerb channel 300mm wide, 50mm thick in PCC M20 grade,sloped towards thekerb,kerbstone with channel laidwith kerb laying machine, foundation concrete laid manually, all complete as per clause 409 (Reference to MORT&H's specification 409). (Rate is including 1% Cess)
92DIVERSION ROAD WORKS :
93Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including settingout, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material (Reference to MORT&H's specification 304). Ordinary soil Manual Means Depth upto 3 m including Cost of dewatering (Rate is including 1% Cess)
94Sand Filling in Foundation Trenches with good local fine sand free from earth not exceeding 150 mm compacted thickness including inundating each layer by profuse water and porking and rammimg layer by layer. Quality of sand is to be approved by the Engineer-in-charge.(Reference to MORT&H's specification 304).(Rate is including 1% Cess)
95Earthwork in filling in foundation trenches with good earth in layers not exceeding 15cm. including watering and ramming layer by layer complete with earth obtained from excavation of foundation or from fresh excavation of land arranged by Department within a lead of 150 m.(Rate is including 1% Cess)
96Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting, finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H'sspecifications1500,1700& 2200). PCC Grade M20 (Including Shuttering)(Rate is including 1% Cess)
97PCC 1:3:6 in Foundation Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days (Reference to MORT&H's specification 2100).(Rate is including 1% Cess)
98Construction of Embankment with Material obtained from Borrow pitsConstruction of embankment with approved material obtained from borrow pits (Land is arranged by the agency) with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 & 300-1 .The size course material in the mix of earth ordinarily shall not be exceed 75mm.(Reference to MoRT&H's specification clause 305).(Rate is including 1% Cess)
99Laying Reinforced Cement Concrete Pipe NP4 / Prestressed Concrete Pipe on First Class Bedding in Single Row . Laying Reinforced cement concrete pipe NP4/prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per the requirements of MORT&H's specification 2900. 1000 mm dia(Rate is including 1% Cess)
100Embankment protection by driving 150 mm dia eucalyptus bullah (main) of length 4.50 m each,@ 300 mm c/c distance, driving 3.00 m into ground, fixing horizontally 100 mm dia bullah as runner at the top of main bullahs, driving 150 mm dia bullah as tie post of length 2.0 m at 1.50 m c/c distance at 1.50m offset distance ,driving tie post to 1.85 m into ground, fitting and fixing ties of 100 mm dia eucalyptus bullah with main bullah and tie post, coal tarring (double coat) on all the bullahs prior to driving, placing cement bags filled with earth after stitching, stacked in layers in double row between main bullahs and embankment, including supply of eucalyptus bullah, cost of nuts and bolts, cost of coal tarring, cost of stitcing (including thread), cost of supply of empty cement bags, cost of sand, labour for driving bullahs including fitting and fixing, placing of bags in position, cost of all machinery tools and implements and other incidental charges if any, all complete and as per direction of Engineer in charge.(Rate is including 1% Cess)
101Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately (Reference to MoRT&H's specification clause 202)By Mechanical MeansBituminous course(Rate is including 1% Cess)
102Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with Disposal upto 1000 metres.: Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m (Reference to MoRT&H's specification clause 301).(Rate is including 1% Cess)
103Providing and applying Primer coat with cationic bitumen emulsion CSS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502). On WMM/WBM surface @ 0.70-1.0kg /sqm using cationic bitumen emulsion CSS1 grade (Bulk).(Rate is including 1% Cess)
104Providing and applying Tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). On Granular surface treated with primer @ 0.25kg-0.30 /sqm using Cationic bitumen emulsion RS1 (Bulk) .(Rate is including 1% Cess)
105Providing and applying Tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).On bituminous surface @ 0.20kg- 0.3kg /sqm using Cationic bitumen emulsion RS1 (Bulk) .(Rate is including 1% Cess)
106Water Bound Macadam: Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density (Reference to MoRT&H's specification 404).By Manual Means Grading 2Using Screening Crushable type such as Moorum or Gravel(Rate is including 1% Cess)
107Clearing and Grubbing Road Land Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs,saplings andtrees girth upto300mm, removal of stumps of trees cut earlier and disposal of unserviceable material sand stacking of serviceable material to be used or auctioned, upto a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. (Reference to MoRT&H's specification clause 201).By Manual Means In area of light jungle(Rate is including 1% Cess)
108By Mix in Place MethodConstruction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401 Grading – V (Rate is including 1% Cess)
109Bituminous MacadamProviding and laying bituminous macadam with 100-120 TPH hot mix plant using crushed aggregates of specified grading premixed with approved bituminous binder @ 3.3% (min) for Grading -1 and 3.4% (min) for Grading -2 by weight of total mix , transported to site, laid over a previously prepared base with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction (Reference to MORT&H's specification clause 504).For Grading 2 (19 mm nominal size, 50-75 mm thick.)Using Bitumen Bulk VG-40 (Rate is including 1% Cess)
110Open - Graded Premix SurfacingProviding, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510).Mechanical method using approved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . Using VG 40 Bulk Bitumen.(Rate is including 1% Cess)
111Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511)Type BProviding and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. Using Bitumen Bulk VG-40(Rate is including 1% Cess)
112Direction and Place Identification Signs upto 0.9 sqm Size Board : Providing and erecting direction and place identification retro reflectorised sign as per IRC:67made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2mm thick with area not exceeding 0.9 sqmsupported on a mild steel single angle iron post75x 75x6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level asper approved drawing (Reference to MORT&H'sspecification 801).(Rate is including 1% Cess)
113R.C. Guard postSupplying fitting and fixing R.C. guard post 1.37m long with C.C. 1:2:4 with graded stone chips of 13.2mm down casting , curing complete including cost of providing 4nos.of 12mm dia. rod of length 1.54m as main reinforcement and 6 nos. of round shaped 8mm dia rods used as binders; the placing of the first binder should be at 75mm below the top finished surface and the other 5 nos of binders should be placed at 245mm c/c ; the guard post is of octagonal section with inscribed circle of dia 24cm at the base tapering to corresponding dimensions of 16cm at the top including two coats of painting with best quality synthetic enamel paint of approved make and grade to form 6 nos. horizontal alternate bands in white/tannery yellow and black to 90 cm length standing up above ground after mendinggood damages if any during striking off shuttering, making hole in ground of 47cm depth and 30cm. minimum dia, fixing the guard posts in the same holes and repacking the earth properly so as to keep the guard posts standing properly erect in correct position true to line and length including carriage of R. C. Guard Post with due care to the site including loading into the truck and unloading at site complete in all respect. (Rate is including 1% Cess)
114Supplying & fixing of Raised Pavement Markers / Road Studs / Cats Eye made of polycarbonate moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face which shall support a load of 13635 kg tested in accordance to ASTM D 4280 Type H and complying to clause no 804 of MoRT&H's specification for Road &Sridge Works (Fifth Rev.). Marker height shall not be less than 10 mm and shall not exceed 20 mm, width shall not exceed 130mm and with minimum reflective area of 13 sq.cm. on each side and slope to the base shall be 35 ± 5 degree. Fixing will be without nails but by using epoxy resin based adhesive as per manufacturer's recommendation including site clearance etc. and complete as directed by the Engineer in Charge .The contractor will have to provide a test certificate from a reputable national/international laboratory conforming the above specifications.
115Metal Beam Crash Barrier Reference to MORT&H's specification 811): Type - A, \\"W\\" : Metal Beam Crash Barrier Providing and erecting a \\"W\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811.(Rate is including 1% Cess)
116Concrete Block Pavement Supplying and Laying in the particular pattern of cement concrete block pavements with BIS certification and spacer nib of size and shape with aspect ratio as per IS 15658 with cement concrete grade not less than M40 on the prepared base course of specified CBR as mentioned in design and drawing with a cushion of bedding sand of 30 to 50 mm thick (grading of the bedding sand as per clause 6.5.1 of IRC SP-63) and filling up the gaps between two paver block with joint filling sand (the grading of the joint filling sand will be as per clause 6.5.2) complete as per IRC SP - 63 with proper confinement of bedding and joint filling sand, compaction,levelling and filling up of the edge gaps with mortar. Type I, II,III, IV should be as per design requeirment or instruction of E-I-C. Type - III (80 mm thickness) inter locking system(Rate is including 1% Cess)
117REMOVAL OF DIVERSION ROAD WORKS :
118Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres (Reference to MORT&H's specification clause 202).By Mechanical MeansCement Concrete Grade (Rate is including 1% Cess)
119Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres (Reference to MORT&H's specification clause 202)Removing all types of Hume Pipes and Stacking within a lead of 1000 metres including Earthwork and Dismantling of Masonry Works.Above 900 mm(Rate is including 1% Cess)
120Carriage of RCC pipes over pucca road upto 1800 mm diameter (Carriage upto 11.00 km with loading-unloading)(Rate is including 1% Cess)
121Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with disposal upto 1000 metres. Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m as per Clause 301 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).(Rate is including 1% Cess)
122APPROACH ROAD SURFACE DRAIN WORKS :
123Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material (ReferencetoMORT&H'sspecification 304). Mechanical MeansDepth upto 3 m (Rate is including 1% Cess)
124Sand Filling in Foundation Trenches with good local fine sand free from earth not exceeding 150 mm compacted thickness including inundating each layer by profuse water and porking and rammimg layer by layer. Quality of sand is to be approved by the Engineer-in-charge.(Reference to MORT&H's specification 304).(Rate is including 1% Cess)
125Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting,finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200).PCC Grade M15 (Including Shuttering) (Rate is including 1% Cess)
126Plain/Reinforced cement concrete in open foundation complete all including vibrating and compacting,finishing, curing, sampling, testing etc. as per drawing and Technical Specifications (Reference to MORT&H's specifications 1500, 1700 & 2200). RCC Grade M20 (Including Shuttering)(Rate is including 1% Cess)
127Supplying, binding, fixing etc. including initial straightening, cutting to requisite length, hooking and bending to correct shape,placing in proper positionof uncoated HYSD reinforcement bar in open founadation complete as per drawing and Technical Specifications (Reference to MORT&H's specifications 1600 & 2200).(Rate is including 1% Cess)
128GST @ 18% on Item no 1 to 10 Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58654180
AUTHORITY Government Departments
TENDER VALUE 18.32 Crore
LAST DATE 18-12-2026
Authority
Authority Name Public Works Department
Work Description Tender for Construction Of Proposed Bridge Over Irrigation Canal In Replacement Of Narrow And Old Minor Bridge At 11.43 Km Of Bhatar Banpas Road Under Burdwan North Highway Division In The District Of Purba Bardhaman.
Basic Detail
Tender No WBPW(R)D/NIT- 10 of SE/WHC-I/2026-2027
Bidding Type Tender
Location
City Purba Bardhaman
State West Bengal
Key Dates
Publish Date 21 Nov 2026
Submission Date 18 Dec 2026
Open Date 21 Dec 2026
Finance
Tender Value 18.32 Crore
Tender Fee Ref. Documents
EMD 10 Lakhs
Exemption Available
Document List
5d66ae73-5411-4147-a6ac-cd007cd0486d.html
BOQ_5217990.xls
Tendernotice_1.pdf
Tendernotice_2.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 21, 2026
11:30 IST

Tender Published

Tender notice published.

Today
Dec 18, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 27 days
Dec 21, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 30 days

Tender Documents

Download All (ZIP) ↓
html

5d66ae73-5411-4147-a6ac-cd007cd0486d.html

xls

BOQ_5217990.xls

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender