Defence Statutory Bodies & Commissions/Committees Closing in 19 days TDR #58646543

Tender For Addition/Alteration To Certain Md Accn At Afs Issapur Construction Of 25 Wg Under Ge (Af) Gurgaon

Issued by Statutory Bodies & Commissions/Committees · Gurgaon, Haryana
Tender Value
43.68 Lakhs
Estimated cost
Bid Submission
11 Dec 2026
19 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Gurgaon → Haryana
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Addition/Alteration To Certain Md Accn At Afs Issapur Construction Of 25 Wg Under Ge (Af) Gurgaon

BOQ

Name of Work:- ADDN / ALTN TO CERTAIN MD ACCN AT AFS ISSAPUR C/O 25 WG UNDER GE (AF) GURGAON
Sl. No. Item Description
1Demolition of cement concrete (un-reinforced) of any description & in any position not specifically provided complete including dismantling of floor tiles etc complete all as specified.
2Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified.
3Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.
4Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition ) of any description in any position not specifically provided complete complete all as specified.
5Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified.
6Demolition of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc.
7Demolition of roof treatment, any thickness including APP, roof tiles, screed bed or plastring and remove the rubish materials outside MOD land at a dumping place marked by any state govt/municipalities etc any distance complete all as specified and directed.
8M&L Non-skid coloured Endura outdoor tiles 10 mm thick (Square/rectangular) of each tile exc 0.06 Sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slury and pointed in coloured cement and pigment to match the tiles complete all as specified and as directed.
9M&L for cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring/tiles etc complete all as specified.
10M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.
11M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.
12M&L 10 mm thick rendering in cement mortar (1:3) on vertical surfaces for backing of tiles etc complete all as specified.
13M&L for Non - skid (joint free) coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.
14M&L for Glazed ceramic coloured tiles in vertical surface 600X300X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified.
15M&L of holes in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors ® complete all as specified.
16M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite complete all as specified.
17Providing edge moulding to 18-20 mm thick stone(any description) of counters vanities etc, including machine polishing to edge to give high gloss finish etc. Complete to Granite stone any description.
18M&L for 40 mm thick PCC (1:2:4) type B-0 (Using 12.50mm graded stone aggregate) as in roof padding complete all as specified & as directed.
19M&L for 15 mm thick plaster in cement mortar (1:4) mixed with water proofing compound on roof slabs finished even and smooth (without using extra cement) after cleaning of roof surfaces with wire brushes complete all as specified.Notes : WPC shall be measured and paid seperately.
20M&L for water proofing treatment with APP (Atactic Polypropylene) modified polymeric prefabricated five layer membrane over roof consisting of cleaning of concrete or plaster surface of roof & parapet walls and applying evenly a bitumen primer confirming to IS 3488 @ 0.40 Kg per sqm laid using buten torch and sealing all joints of APP modified polymeric water proofing membrane minimum weight 3.6 kg/sqm reinforced with non woven polyester fabric (weight not less than 160 grams per sqm) unrolled and bonded to substrata with logitudinal and end laps 100 mm and 150 mm respectively as per manufacturer's instructions including aluminium paint on top surface complete all as specified.
21Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified.
22M&L for providing plain cement concrete (1:2:4) type B0 (using 12.5 mm graded crushed stone aggregate) as in coping or roof kerbs on roof chamfered on edge rounded or chamfered on edges including trowelling slightly complete all as specified.
23M&L for Cement concrete tiles 25cm x 25cm x 22 mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished, set with grey cement and pigments over 15mm thick cement screed bed in cement mortar 1:4 complete all as specified and directed.
24Removing bldgs demolished materials / debries exc. 1.50 km but n exc. 5 km and depositing where directed.
25M&L for brick work with sub class 'B' old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 etc complete all as specified.
26M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.
27M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified.
28Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick rough finished in flat surface complete all as specified.
29Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 5 cm but n exc 10 cm wide rough finished complete all as specified.
30M&L for rendering 15 mm thick in cement mortar (1:6) on brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified.
31M&L for 15 mm thick plastering in two layers (10+5) mm in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer's instruction and complete all as specified.Note: WPC shall be measured and paid separately.
32M&L rendering 10mm thick in cement mortar (1:3) as in ceilings finished even and smooth (without using extra cement) complete all as specified.
33Supply only Liquid water proofing compound ISI Marked complete all as specified.
34M&L for preparation of newly plastered or unplastered/undecorated surface of wall and applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre over a coat of primer, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified.
35M&L for preparation of plastered or unplastered old decorated surface of wall by complete removal of existing treatment by mechanised sander of berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre over a coat of primer, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes.(b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.
36M&L for preparation of newly plastered or unplastered/undecorated surface of ceiling and applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified.
37M&L for preparation of plastered or unplastered old decorated surface of ceiling by complete removal of existing treatment by mechanised sander of berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre over a coat of primer, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes.(b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.
38M&L for preparation of newly plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified.
39M&L for preparation(complete removal of existing treatment) of old decorated external wall/ceiling surface of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on wall/ceiling surface including filling of holes and cracks with with suitable material like cement or plaster of paris etc thus make surface smooth upto 4th storey buildings complete all as specified and as directed. Note : (a) Stage for complete removal of existing surface & Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes.(b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.
40M&L for providing 3mm thick wall care putty on wall before applying oil bound distemper and making the surface uniform all as specified.
41M&L for providing 3mm thick wall care putty on ceiling before applying oil bound distemper and making the surface uniform all as specified.
42M&L for guniting work to RCC work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and S&F welded wire mesh fabric or wire net less than 95 X 95X 3 mm adhesive, plaster grade for concrete admixture 1 part of cement and 3.5 part of sand and average thickness 40 mm and making the surface even including 15mm thick plastering in cement mortar (1:4) on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement plumb and making surface true to geometry in line and including necessary form work to be carried at upto double storey building Note.- Where ever reinforcement required will be measured and paid seperatly etc complete all as specified.
43Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified.
44Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified.
45Taking down shutter of any description exc 1 Sqm and n exc 2 Sqm and removing from site.
46Taking down shutter of any description exc 1 Sqm and n exc 2 Sqm and refixing in same opening.
47S&F for Pressed steel frames 125X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.
48S&F for Pressed steel frames 105X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.
49M&L cement concrete (1:3:6) type C1, (using 20 mm graded stone aggregate) as in filling of door frames of pressed steel and in bed blocks etc complete all as specified.
50S&F factory made 35mm thick flush shutters , solid core construction with block board core and plywood face pannel commercial type on both faces complete all as specified.
51S&F factory made 35mm thick 2nd class hardwood glazed and skelton door shutters, open rebated and prepared to receive glass, gauze, (without sash bars) edges for framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) fitted to chowkats complete all as specified.
52S&F solid PVC door frame of size 50mm X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification and drawing.
53S&F factory made PVC shelter panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement , supplying and fixing in the frame at site as per specification & drawing as specified.
54S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.
55S&F 100 mm Butt hinges, Stainless steel and fixed complete all as specified and as directed.
56S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.
57S&F 150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.
58S&F 250 mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified and as directed.
59S&F 300mm, ordinary rat tail made of brass rod pattern springs including roller and roller plate complete
60S&F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed.
61S&F floor door stopper 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.
62S&F window or ventilators section of frame 72x55mm fixed to wall or concrete surface with rowl plugs made of galvanised steel powder coated and section of shutter 47x20mm mulion section 72x50mm (Based steel as per IS 513 \\"D\\" quality galanised as per IS 277 with zinc of 120 gms/sqm) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made of square bars powder coated fixed to window frame with screws including necessary fittings and all builders hardware such as handles, tower bolts and stays etc complete all as specified and as directed. Make : NCL type-4000 Series (Note : Glass and wiremesh shall be measured and paid separately under respective items)
63S&F sheet glass 4 mm thick ordinary quality and glazing with oil putty, rubber strip or wooden beads complete all as specified.
64Dismantling boarding of any description , fixed in any position with nails complete all as specified and as directed.
65Supply & Fixing of 18 mm thick WPC celluka ply of plain colour fixed with screws, solvent cement/adhesive to make cupboard/kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by Engr-in-Charge. (Make: Rajshri Plastiwood)
66Supply & Fixing of 18 mm thick WPC celluka ply of one side Prelam/Rigidlam and other side balancing laminate colour to make cupboard/kitchen cabinet shutter/drawer front shutters complete as per specifications and as directed by Engr-in-Charge. (Make: Rajshri Plastiwood)
67Supply & Fixing of 12 mm thick WPC celluka ply of plain white colour fixed with screws, solvent cement/adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by Engr-in-Charge. (Make: Rajshri Plastiwood)
68Supply & Fixing for 20 mm wide & 1 mm thick PVC edge bending of PVC pasted on edges with suitable adhesive complete as per specifications and as directed by Engr-in-Charge. (Make: Rajshri Plastiwood)
69Supply & Fixing of auto closing hinges openable at 0 degree for kitchen cabinet shutters complete as per specifications and as directed by Engr-in-Charge. (Make: Rajshri Plastiwood)
70Supply & Fixing of stainless steel handles 100 mm size for kitchen cabinet/cupboard shutters (Make: Hettich,Ebco,Prime)
71S&F 25 mm outer dia medium weight pipe made out of stainless steel 304 grade, including decorative ornamental knobs at both ends and one set of ornamental decorative Stainless steel clamps to fixed to walls complete all as specified.
72Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/Disintegrtated rock complete all as specified.
73Removing excavated material to distance not exc 50 metre and depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-Charge
74Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified.
75M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified.
76Dismantling of cast iron pipe up to 100 mm dia, jointed in cement mortar and taking out in trenches/Wall if required etc complete all as specified.
77S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls complete all as specified.
78S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches or floor complete all as specified.
79S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches or floor complete all as specified.
80S&F 110 mm dia PVC (SWR) vent cowl complete all as specified.
81S&F 110 mm dia PVC (SWR) bends with rubber rings joints fixed as required complete all as specified.
82S&F 75 mm dia PVC (SWR) bends with rubber rings joints fixed as required complete all as specified.
83S&F 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal with rubber rings joints fixed as required complete all as specified.
84S&F 75 mm dia PVC (SWR) junction single, (Single T) equal or unequal with rubber rings joints fixed as required complete all as specified.
85S&F PVC gully traps (150X150) mm, square or round mouthed, type 'P' complete all as specified.
86M&L PVC (SWR) 75 mm floor trap plain with grating including jointing with solvent cement complete all as specified.
87S&F 110mm PVC (SWR) WC connector bent type complete.
88Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store. complete all as specified.
89All as per item No. 88 here-in-before but 20mm dia .
90Providing and fixing 25 mm nominal dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.
91Providing and fixing 20 mm nominal dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work, including cutting chases and making good the walls etc.)
92Supply and fixing in CPVC 25mm Ball valve with iron rod complete all as specified.
93S&F in repair 20/25 mm dia PVC gate valve with head, screwed both ends for CPVC pipe complete all as specified.
94S&F in repair white vitreous China wash down water closet pan (pedestal pattern), and trap (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, plastic water closet sheet covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device etc. complete all as specified.
95S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified.
96S&F in repair Vitreous China wash basin, white, flat back of size 550x400mm with pedestal including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including cutting for and pinning in ends of brackets complete all as specified.
97S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified.
98S&F Soap dish of chromium plated or stainless steel fixed to wall with chromium plated brass screws.
99S&F in repair PVC connection 450 mm long suitable for 15 mm GI pipe with two brass nuts & rubber washers complete all as specified.
100S&F in repair Wall mixer with bend pipe for overhead shower with built-in non return valve , 15mm bore chromium plated fancy type complete all as specified.
101S&F in repair 15 mm dia angle valve, cast copper alloy screwed down high pressure, fancy type chromium plated screwed both ends for iron pipe or unions complete all as specified.
102S&F in repair angular two way angle cock with wall flange, 15 mm nominal bore cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified.
103S&F in repair bib taps long body, brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket with water saving aerator complete all as specified.
104S&F in repair Pillar cock with swan neck spout (left/right) and aerator , 15mm bore chromium plated fancy type complete all as specified.
105S&F in repair chromium plated shower roses 125 mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified.
106S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.
107S&F in repair 100 mm chromium plated grating complete all as specified.
108S&F chromium plated health faucet telephonic type with 8mm dia, 1 meter long CP flexible with wall hook and jet of approved make, suitable for 15 mm bore iron pipes or for unions and fixed complete all as specified.
109S&F in repair Corner glass shelf (with bracket) , fancy type with stainless steel railing fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.
110S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified.
111Dismantling of existing water tanks of steel/PVC/AC of capacity exceeding 250 liters but not exceeding 500 litres complete all as specified.
112S&F for rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylinderical vertical with closed top) hoisted and fixed in position all as per SSR Part I complete all as specified.
113S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including one number chromium plated waste fittings 40 mm dia & waste pipe complete all as specified and as directed.
114S&F kitchen plate rack stainless steel 1 mm thick of size 60cmx75cm complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed.
115S&F rolled mild steel in framed work as in doors or steel gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing conforming to Fe- 290.Gde-E-165 complete all as specified.
116S&F 1.60 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.
117S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with selftapping screws as specified & directed.
118M&L preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.
119M&L prepration of new Steel surfaces of any description, not otherwise described, over 10cm width or girth & applying two coats of synthetic enamel paint complete all as specified
120S&F door seal bottom with aluminium plate and rubber insulation 42'' x 1.5'' complete all as specified.
121S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.
122M&L 100 mm thick PCC 1:4:8 tybe D-2 using 40mm stone aggregate as in subbase.Complete all as specified
123M&L for screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.
124M&L for 22-25 mm thick chequered designer coloured tiles (glass finish), size, colour and shape as approved by GE, set and jointed in neat cement slurry and pointed with coloured cement to match etc complete all as specified as directed.
125Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.
126M&L for preparation of new concrete surface and applying two coat of synthetic enamel paint exc 10 cm girth or width not other wise described over a coat of primer etc complete all as specified.
127Taking down carefully old copper/alluminium point, wiring (light, fan, socket or power) complete, including fitting such as switches, ceiling roses, pendants, regulator socket tube light fitting of any type, Bulk head fitting etc segregation serviceable fitting/fixture and keep them safe custody for reuse and removing materials from the site and making good disturbed surface of walls&floors etc as per existing specification complete all as directed
128Taking down old unserviceable main switch, DB's/RCBOs/MCCB/Sheet Metal Enclosures including MCBs & wooden/GI/MS sheet board etc and removing materials from the site of work complete all as directed
129Taking down old unserviceable sub main wiring any size/core/type of copper/alluminium conductor. including making good the disturbed surfaces and removing materials from the site of work complete all as directed .
130M&L for point wiring complete with stranded copper conductor 1.5 sqmm single core (nominal area ) PVC insulated and unsheathed cable 650 volts grade drawn in and including medium duty concealed in PVC concealed conduit conforming to IS and ISI marked not less than 19 mm dia with 1.6mm thick concealed pressed steel terminal boxes with plate and framecover for rquired module including single core stranded copper conductor 1.5 sqmm PVC insulated unsheathed cable in same conduit as earth wire to the common earth and connecting to earth dolly all as specified for
131(a) One light point/bell point/one fan/exhanust fan/ bell point controlled by one,one way switch.
132(b) For one 5 pin, socket outlet 5/6 amp on independent board with other switches
133(c) For one 5 pin socket outlet 5/6 amp on same board
134M&L for point wiring complete with stranded copper conductor 2.5 sqmm single core (nominal area ) PVC insulated and unsheathed cable 650 volts grade drawn in and including medium duty concealed in PVC concealed conduit conforming to IS and ISI marked not less than 19 mm dia with 1.6mm thick concealed pressed steel terminal boxes with plate and framecover for rquired module including single core stranded copper conductor 2.5 sqmm PVC insulated unsheathed cable in same conduit as earth wire to the common earth and connecting to earth dolly all as specified for 16/6 amps on an independent board.
135M&L for point wiring complete with stranded copper conductor 4 sqmm single core (nominal area ) PVC insulated and unsheathed cable 650 volts grade drawn in and including medium duty concealed in PVC concealed conduit conforming to IS and ISI marked not less than 19 mm dia with 1.6mm thick concealed pressed steel terminal boxes with plate and framecover for rquired module including single core stranded copper conductor 4 sqmm PVC insulated unsheathed cable in same conduit as earth wire to the common earth and connecting to earth dolly all as specified for AC Point.
136M&L for switch modular type single pole one way 6 amps complete all as directed by Engr - in - charge.
137M&L for switch modular type single pole one way 16 amps complete all as directed by Engr - in - charge.
138M&L socket outlet 2 in 1,3/5 pin 6 Amp modular type multipurpose complete all as specified by Engr-in-Charge
139M&L socket outlet 2 in 1,3/5 pin 16 Amp modular type multipurpose complete all as specified by Engr-in-Charge
140S&F electronic Step type , 120 watt -2 modul modular fan regulator . Make : Anchor/Surya/Havells odulardular
141M&L ceiling rose , single phase /PVC /Polycarboante isolated body.
142S&F in call bell, Ding dong type, 230 volts AC single pole complete all as directed.
143Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 240 volt complete all as specified and directed .
144M and L for Sub main wiring with 2 Run of 6 Sqmm cable and one run of 6 sqmm as earth wire PVC insulated, unsheathed FR cable of multistranded copper conductors 1100 volt grade IS- 694 marked drawn through and including non metalic PVC conduit pipe medium grade ISI marked (not less than 25 mm dia) along with fittings and accessories concealed on wall and surface on ceiling complete all as specified and directed by Engineer in charge.
145Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 200mm complete with making arrangement for fixing of exhaust fan on steel/Aluminium frame window/ making opening in brick wall as per site requirement and also making good to disturbed surfaces as per matching to existing complete all as specified and as directed by Engr-in-Charge
146Supply and fix in replacement of exhaust fan steel body, heavy duty, AC Single phase, voltage 230V, 50 Hz, Copper winding of size 200/225 mm sweep with, blades and frame and lovers complete with making arrangement for fixing of exhaust fan on steel/Aluminium frame window/ making opening in brick wall as per site requirement and also making good to disturbed surfaces as per matching to existing complete all as specified and as directed by Engr-in-Charge
147Taking down ceiling fans/exhaust fan from site safely and deposited to mes store for further refixing the same complete as directed.
148Fixing only ceiling fan received from mes store and connecting up including provision of cable from ceiling rose or connector to fan complete all as directed by Engineer-in- charge.
149Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc complete all as specified and as directed.
150Supply and fixing Pressure die cast aluminium housing LED street light luminaires with IP66 of 35/45 Watts .
151Supply & Fix in repair bracket for street light fittings made out of 40 mm bore medium grade GI tubing 1.2 m long bent to shape and including suitable size of MS clamps, nuts, bolts and washers applying two coats of aluminium paint over a coat of red oxide zinc chrome primer repair complete all as specified and directed.
152Supply and fix LED batten with 20W LED batten with ' eye soft' technology and glarefree diffuser light fittings suitable for fixing on wall/surface with all required connecting accessories like PVC box base,flexible cable from ceiling rose to light fittings etc as directed and specified by engr-in-charge.Make havells Cat part No LHEXARP7SN1W020 or equivalent in CG/Bajaj
153Supply and fix LED batten with 10W LED batten with ' eye soft' technology and glarefree diffuser light fittings suitable for fixing on wall/surface with all required connecting accessories like PVC box base,flexible cable from ceiling rose to light fittings etc as directed and specified by engr-in-charge.Make havells Cat part No LHEXACP71N1W010 or equivalent in CG/Bajaj Please Enable Macros to View BoQ information
154Supply and fix LED batten with 10W LED batten with ' eye soft' technology and glarefree diffuser light fittings suitable for fixing on wall/surface with all required connecting accessories like PVC box base,flexible cable from ceiling rose to light fittings etc as directed and specified by engr-in-charge.Make havells Cat part No LHEXACP71N1W010 or equivalent in CG/Bajaj Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58646543
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 43.68 Lakhs
LAST DATE 11-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Addition/Alteration To Certain Md Accn At Afs Issapur Construction Of 25 Wg Under Ge (Af) Gurgaon
Basic Detail
Tender No GE/GUR-/NIT-118/2026-27
Bidding Type Tender
Location
City Gurgaon
State Haryana
Key Dates
Publish Date 20 Nov 2026
Submission Date 11 Dec 2026
Open Date 14 Dec 2026
Finance
Tender Value 43.68 Lakhs
Tender Fee 500
EMD 88000
Exemption Not Available
Document List
3c08d673-f06e-4bef-8b7b-c22c10e4ac3d.html
BOQ_897262.xls
TenderDocumentsNIT118.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 20, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 11, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 19 days
Dec 14, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 22 days

Tender Documents

Download All (ZIP) ↓
html

3c08d673-f06e-4bef-8b7b-c22c10e4ac3d.html

xls

BOQ_897262.xls

pdf

TenderDocumentsNIT118.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender