Tender For Special Repair To Bldg No P-84 Family Ward Of Mh Bhuj At Mil Stn Bhuj Under Ge(A) Bhuj.
Tender Value
36.89 Lakhs
Estimated cost
Bid Submission
11 Dec 2026
19 days left
EMD
73780
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kachchh → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No P-84 Family Ward Of Mh Bhuj At Mil Stn Bhuj Under Ge(A) Bhuj.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of existing PCC as in form of roof padding incl backing over roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, complete all as specified and dirceted.Note :- Incl taking down existing water profing membrane |
| 2 | M&L for cement concerete type B2 1:2:4 (20 mm graded aggrigate) as in mass concerete roof for padding, floor and foundations etc complete all as specified and dirceted. |
| 3 | Material and labour for roof surface treated with PU Elastoseal primer with Epoxy Primer to seal the pores and enhance the adhesion of the coating, supplying and applying single component waterproofing liquid membrane based on pure, elastomeric, polyurethane resin cold applied of spray/brush applied membrane with an elongation of 650%+ 50 and tensile strength not less than 2 Mpa, crack bridging ability not less than 2mm. No leakage upto 5 bars of water pressure. Shore Hardness > 50 Shore. The minimum thickness to be applied shall be 1.5 mm, (overall) in two layers (each layer 750 micron) or as per manufacturer’s instructions so as to achieve thickness not less than 1.5mm including providing & laying of protective Geotextile fabric 150 GSM over the entire membrane with proper overlaps of 75mm complete all as specified and as directed.Note : (i) The treatment shall be carried out by authorised applicator approved by GE as per the manufacturerMake for PU Primer/ Membrane SIKA/ BASF, BERGER/ STP FOSROC/ SAINT GOBAIN, PIDILITE. |
| 4 | Making benching / Roof Kerbing with PCC (1:2:4) type B0 using WPC as per manufacturer's instruction along side wall adjoining to roof in concave shape complete all as specified and directed. Note : WPC shall be measured and paid separately. |
| 5 | Supply only Integral WPC complete all as specified and directed. (Make: Pedilite/Roft/Fosroc/Bauchemic India/Cico) |
| 6 | Demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above ground level) complete all as specified and dirceted. |
| 7 | M&L Cement concrete ( 1:3:6) type C- 2, using (40mm graded stone aggregate) 75 mm thick as in sub base /plinth protection etc. Finishing cement concrete surface even and smooth without using extra cement complete all as directed. |
| 8 | Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed. |
| 9 | M&L Rendering 15 mm thick of CM 1:4 on fair faces of brick or concrete surfaces is to be finished even and smooth without using extra cement with mixing of water proofing compound complete all as directed. |
| 10 | M&L Rendering 10 mm thick of CM 1:6 on fair faces of brick or concrete surfaces is to be finished even and smooth without using extra cement with mixing of water proofing compound complete all as directed. |
| 11 | Complete removal of existing treatment of any type/description from walls/RCC surfaces/ceiling/chajjas/roof projections etc with mechanical means/grinder complete all as specified and dirceted. |
| 12 | M&L for applying acrylic wall care putty on old/ new plastered internal/External surfaces of walls/ceilings/soffits (thickness vary from 3 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed.Make of wall Putty : JK wall Putty / Birla Wall care Putty / Bison Wall Putty.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE. |
| 13 | Preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) old/new surface with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.Make of Exterior Wall Primer : Asian / Berger / Nerolac [Best Quality].Make of Exterior Emulsion : Asian (APEX) / Berger (WEATHER COAT ANTI DUST) / Nerolac (EXCEL TOTAL) . |
| 14 | Preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) old/new surface @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer on existing yellow coloured surface complete all as specified and directed.Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality].Make of Interior Emulsion : Asian (tractor shyne) / Berger (bison) / Nerolac (BEAUTY sheen) |
| 15 | Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed. |
| 16 | Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each complete all as specified and directed. |
| 17 | M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. Make: Jindal |
| 18 | M&L for Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and dirceted. Note : Panel filling i.e.. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately. By Engr-in-charge |
| 19 | S&F 4.8 mm thick tinted glass of selected quality in square not exceeding 0.5 sqm in each pane, fixed to aluminium frame with and including suitable rubber beading complete all as specified and directed |
| 20 | S&F 12 mm thick prelaminated particle board, Exterior grade prelaminated and both sides with decorative choice laminations complete all as directed. |
| 21 | S & F Powder coated Aluminium alloy sections sliding windows with frames Series-C 20mm of frame size 92 x 31.75 x 1.90 mm and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass 4mm thick and stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. |
| 22 | M & L for powder coated aluminium grill of design No DG-104, 7.5mm thick sections of deco grill or of equivalent approved make with 1 mm thick 'F' sections of suitable size complete all as specified and directed. |
| 23 | S&F aluminium powder coated ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified and dirceted. |
| 24 | M&L Gl frame work (Size of grid 605 x 605mm) for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and dirceted. |
| 25 | M&L Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and dirceted. |
| 26 | Supply and Fix in repairs, seamless ceiling with using 12mm thick, factory made gypsum fiber board, fixed on GI frame work for seamless ceiling suitable for suspended system with and including applying two coats of oil bound distemper over a coat of primer to give even and smooth finish without showing any joints complete all as specified and directed. |
| 27 | S&F for butt hinges 100mm size medium weight stainless steel complete all as specified and directed. |
| 28 | M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed. |
| 29 | S&F Aluminium anodised barrel tower bolt of extruded section 200 mm size complete all as specified and directed. |
| 30 | S&F stainless steel sliding door bolt with hasp and stapple (bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed. |
| 31 | S&F Floor door stopper of overall length of cover plate 140mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and dirceted. |
| 32 | S&F Aluminium (die cast body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all specified and directed. |
| 33 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 34 | M&L for double charged Virified Ceramic coloured tiles 10 mm thick (square/ rectangular) polished, size of each tile 1200x600mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed. Make: Johnson (Marbonite)/Kajaria/Somany/ Orient Bell Granito/ Asian Granito/ Oracle Grenito (Marbito) |
| 35 | M&L for double charged Virified Ceramic coloured tiles 10 mm thick (square/ rectangular) polished, size of each tile 1200x600mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchas in as in vertical surface like dado/ skirting etc , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed. Make: Johnson (Marbonite)/Kajaria/Somany/ Orient Bell Granito/ Asian Granito/ Oracle Grenito (Marbito) |
| 36 | M&L for non skid ceramic ede cut tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4, complete all as specified and as directed. Make : Somany/Johnson/Kajariya/Sunheart. |
| 37 | M&L for glazed ceramic tiles (coloured) 600x300x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, complete all as specified and as directed. Make : Somany/Johnson/Kajariya/Sunheart. Please Enable Macros to View BoQ information |
| 38 | M&L for glazed ceramic tiles (coloured) 600x300x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, complete all as specified and as directed. Make : Somany/Johnson/Kajariya/Sunheart. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysDec 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender