Defence Statutory Bodies & Commissions/Committees Closing in 20 days TDR #58646430

Tender For Addition/Alteration To Perimeter Wall At Certain Location At Af Stn Jodhpur Under Ge Af No 2 Jodhpur

Issued by Statutory Bodies & Commissions/Committees · Jodhpur, Rajasthan
Tender Value
43 Lakhs
Estimated cost
Bid Submission
12 Dec 2026
20 days left
EMD
86000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Addition/Alteration To Perimeter Wall At Certain Location At Af Stn Jodhpur Under Ge Af No 2 Jodhpur

BOQ

Name of Work:- ADDN/ALTR TO PERIMETER WALL AT CERTAIN LOCATION AT AF STN JODHPUR UNDER GE AF NO 2 JODHPUR
Sl. No. Item Description
1Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for fixing of Y angle on wall in required shape complete all as specified and directed.
2Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.
3S & F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending, 'Y'shaped angles over boundry wall and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290. Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') including fabrication work/ weilding complete all as specified and directed.
4S & F galvanised, 2 stand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails staining bolts incl securing or tying at crossing with and provision of galvanised mild steal wire staples or steel pins etc as directed (each line wire to be measured) complete all as specified as directed by Engineer-in-Charge.
5All as per srl item No 04.00 above but fixing only.
6S&F Razor type Concertina coil hot galvanised spring tensile wire 145 to 150 Kg/Sqmm. weight of coil shall be minimum 8.57 Kg per coil. Stretch of each coil shall be min six meters. No of each coil shall be 50. Galvanised razor ribbon tape shall be of size 0.5 mm thick. 19 mm wide before wrapping on central core wire etc all as specified as directed by Engineer-in-Charge.
7M&L for Providing, cement concrete type B-1 1:2:4 using 20mm graded crushed stone aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs , watertroughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed by Engineer-in-Charge.
8Formwork to sides of pillars, posts, struts, piers, columns, & stanchions Rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified and directed.
9M & L for Painting to new steel surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with red oxide zinc chrome primer (one coat) and finishing with two coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.
10M & L for Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge
11M & L for preparing of plastered surfaces of walls and applying two coat of cement based paint over a coat of primer chalk whiting complete all as specified as directed by Engineer-in-Charge.
12M & L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/angle, fixed with self tapping screws as specified on perimeter wall fixed with existing Y angle complete all as specified as directed by Engineer-in-Charge.
13M & L for preparing of Old plastered or unplasterd surfaces of walls by washing, rubbing down and stopping of distempered and painted surfacesand applying one coat of cement based paint over a coat of primer chalk whiting complete all as specified as directed by Engineer-in-Charge.
14M&L for preparation of old decorated plastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces by mechanical means using suitable tools and plants as per manufactures instructions.
15Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc completed as directed by Engineer-in-Charge
16M&L for rendering 15 mm thick cement plaster in two layers (10+5) with bottom layer 10mm thick in CM 1:6 and top layer 5mm thick in CM 1:4 mixed with water proof compound @ 3% by weight of cement or as per manufacturers instructions finished even and smooth without using extra cement up to any height as directed by Engineer-in-Charge. (water proof compound measured in this item) .
17M&L for preparation of new decorated plastered or unplastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces by mechanical means using suitable tools and plants as per manufactures instructions.
18M&L complete removal of old treatment by mechanical means from walls and making good the holes, patches with putty and cement mortars (1:4) as required and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces by mechanical means using suitable tools and plants as per manufactures instructions and as directed by Engineer-in-Charge.
19M&L Demolition of Brickwork or stone/ boulder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified.
20M&L for Squared rubble walling Jodhpur type, regular coursed, well bonded, bedded and solidly hearted, built, built in CM 1:6 complete all as specified and directed.
21ditto as per item No 20.00 above but except stone complete all as specified and directed.
22Extra over items as above for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type, brought upto courses complete all as specified and as directed.
23M&L for keyed pointing, to squared rubble, random or polygonal rubble, uncoursed or brought upto course in CM 1:4 complete all as specified and as directed.
24Raking out joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses.Note:1.The rates include for raking or cutting out joints and decayed mortar etc, not less than 12mm deep, washing the joints, removing rubbish off the premises, and keeping the surface to be pointed wet for 2 days prior to re-pointing.2. The rates for raking out joints in old work and pointing apply to both plain (horizontal, vertical or inclined) and circular surfaces, in any width of joint.
25Excavation in trenches n.exc 1.5 m wide or n exc 10 sqm in plan area and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.
26Returning, filling in approved soft/loose soil including spreading, leveling, watering and well ramming in layers each n.exc 25cm complete all as specified and as directed by Engineer-in-Charge.
27Removing surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engineer-in-Charge.
28M&L for plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in mass filling and foundation complete, all as specified and as directed by the Engineer -in-Charge.
29Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter Rough finished surfaces of concrete flat, complete all as specified and as directed by Engineer-in-Charge
30Use and waste of form work to sides and soffits of floor or roof beams, beam hunching, girders, bressummers, lintels over 1.5 metre span, cantilevers, shelves including supports, for rough finished surfaces of concrete, complete all as specified and as directed by Engineer-in-Charge
31M&L RCC M-25 design mix using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engineer-in-Charge
32M&L RCC M-25 design mix using 20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and as directed by Engineer-in-Charge
33M&L RCC M-25 design mix using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by Engineer-in-Charge
34M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and as directed by Engineer-in-Charge
35M&L Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and as directed by Engineer-in-Charge
36Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor & roofs n exc 20 cm wide & sides of RCC/PCC bands in walls, horizintal or sloping & similar work exc 10cm but n exc 20cm wide Roughed finished surface of concrete complete all as specified and as directed by Engineer-in-Charge
37M&L Pre-cast cement concrete block type C1 1:3:6 (20mm graded coarse agg) set in Cm 1:4 masonry with solid blocks, exc. 10 cm in width and setting in mortar,complete all as specified and as directed by Engineer-in-Charge
38M & L for preparing of new plastered surfaces of walls and applying two coat of cement based paint over a coat of primer chalk whiting complete all as specified as directed by Engineer-in-Charge.
39M&L of 20mm thick pre-formed filler board for expansion joints complete all as specified and directed.
40Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete, brick work , masonry etc any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.
41M&L of Mild steel as in fencing posts, struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, drilling, bolting or riveting etc. including necessary welding where required , conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-charge.
42Supply only Chain link fencing MS galvanised fencing, any size or type all as specified and as directed by Engineer-in-Charge.(Note - Dia of main bar 4mm and cross bar 4mm)
43Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts etc including provission of binding wire and fixing with MS angle iron fencing posts complete all as directed.
44S & F of 10 mm dia 50mm Length Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long all as specified and as directed.
45M&L Mild steel galvanised concertina coil fencing with punched tape concertina coil of any dia as per site requirement, 10 metre openable length (total length 142 mtrs), having 50 Nos. rounds per 6.0 metre length, spring core wire (2.5 mm dia galvanised wire) of high tensile strength not less than 400-450 gm/ Sqmm with tape (0.52mm thick) and weight 2.0 Kg/metre and fixing the same with existing Y-shaped angle iron placed 2.0mtrs apart and with 6 horizontal R.B.T. (Reinforced Barbed Tape) wire, stud tied with G.I. staple sand, 125 to 127 Nos. of G.I. clips in one coil, to retain horizontal, including necessary nuts and bolts, including taking down existing rusted/damaged concertina coil complete all as specified and as directed by Engineer-In-Charge.
46M&L for Mild steel work conforming to Fe 290 Gde E-165 as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclusive of MS steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed by Engineer-in-Charge.
47NOTE;- Amount of credit of Rs 155592.00 for retrived material is mentioned in schedule of credit on srl page No 20.00 of tender document in pdf from which will be deducted offline whlie acceptance Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58646430
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 43 Lakhs
LAST DATE 12-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Addition/Alteration To Perimeter Wall At Certain Location At Af Stn Jodhpur Under Ge Af No 2 Jodhpur
Basic Detail
Tender No 8635/E8
Bidding Type Tender
Location
City Jodhpur
State Rajasthan
Key Dates
Publish Date 20 Nov 2026
Submission Date 12 Dec 2026
Open Date 14 Dec 2026
Finance
Tender Value 43 Lakhs
Tender Fee 500
EMD 86000
Exemption Available
Document List
4f8f24eb-5f84-4ab0-8e41-0a6900236bdc.html
BOQ_897197.xls
tenderdocument.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 20, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 12, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 20 days
Dec 14, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 22 days

Tender Documents

Download All (ZIP) ↓
html

4f8f24eb-5f84-4ab0-8e41-0a6900236bdc.html

xls

BOQ_897197.xls

pdf

tenderdocument.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender