Civil Aviation Boards / Undertakings / PSU Closing in 19 days TDR #58645996

Tender For Miscellaneous Civil & Interior Work For Improvement Of Rajiv Gandhi Bhawan, New Delhi For The Year 2026-27.

Issued by Boards / Undertakings / PSU · Delhi, Delhi
Tender Value
70.05 Lakhs
Estimated cost
Bid Submission
11 Dec 2026
19 days left
EMD
2.10 Lakhs
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Miscellaneous Civil & Interior Work For Improvement Of Rajiv Gandhi Bhawan, New Delhi For The Year 2026-27.

BOQ

Name of Work:- Miscellaneous civil & interior work for improvement of Rajiv Gandhi Bhawan, New Delhi for the year 2026-27.
Sl. No. Item Description
1Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).a) Second class teak wood
2Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).a) Kiln seasoned and chemically treated hollock wood
3Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:2nd class teak wood a) 50x12 mm
4Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:2nd class teak wood a) 25x12 mm
5Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.a) 1.0 mm thick
6Providing & fixing 12mm thick and 100mm wide, 2nd class teakwood skirting on partition & panelling etc. with angular/half round edges complete as per the direction and satisfaction of Engineer-in- Charge.
7Providing and fixing partition upto required height consisting of G.I. frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor, middle and ceiling channel (wherever required) 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling (wherever required) at the spacing of 610 mm centre to centre with suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre all complete as per manufacture's specification and direction of engineer in charge.
8Providing & fixing 8 mm plywood of approved make to existing walls/ frames with necessary screws etc. all complete as per the direction and satisfaction of Engineer-in- charge.(The cost includes for providing openings for electrical wiring & switches etc.)
9Dismantling Aluminium / gypsum / wooden /PVC partition ,doors, windows,fixed glazing and false ceiling including disposal of unservicable surplus material and stacking of serviceable material within RGB premises as directed by Engineer-in-Charge.
10Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:a) 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
11Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.a) Twin rubber stopper
12Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
13Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
14French spirit polishing :(a) Two or more coats on new works including a coat of wood filler
15Providing & Placing in Position Custom made filing/ storage unit of required depth and size all complete as per direction and satisfaction of Engineer-in- charge. :a) The carcase and shelves shall be made with 18 mm thick commercial ply and back with 8 mm thick commercial plywood. The shelves are to be provided at an approximate gap of 300 to 400 mm as per direction of EIC. The edges of commercial plywood shall be covered with PVC Edge Tape.b) All outer surface shall be finished with 1.0 mm thick decorative / coloured high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.c) All inner surfaces and shelves shall be finished with 0.65 mm thick liner laminate in suede finish and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.d) Shutters shall be made with 19 mm thick commercial board and to be fixed with 2 / 3 nos. SS butt hinges of size 75X20X25 mm, 100 mm S.S handles (one on each shutter), magnetic catcher, tower bolt and Multi purpose lock. f) The shelves should be supported with two numbers shelf pin on each side. (For payment purpose Front area to be measured.) (Note: The item includes cost of all material, labour and fixing charges as per the site requirements. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)
16a) Upto and including 300 mm depth
17b) 450 mm depth
18c) 600 mm depth
19Providing & fixing 18 mm plywood of approved make to existing walls/ frames with necessary screws etc. all complete as per the direction and satisfaction of Engineer-in- charge.(The cost includes for providing openings for electrical wiring & switches etc.)
20Providing and placing drawer unit of size 400(W)X500(D)X600(H) mm as per direction & satisfaction of Engineer-in-charge.a) The carcase of drawer unit including front side will be made with 18 mm thick Commercial ply board and back with 8 mm commercial plywood & edge to be covered with PVC edge tape at all exposed edges. All outer surface shall be laminated with 1.0 mm thick decorative / coloured high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.b) Drawer's sides, front and back shall be made with 12 mm plywood of height 150 mm (approx) for 1st & 2nd drawers and 300 mm (approx.) for bottom drawer. The base of all drawers shall be made with 8 mm thick plywood. All inner surface shall be laminated with 0.65 mm thick laminate, edges to be finished with PVC edge tape at all exposed edges, including cost of adhesive of approved quality.c) All drawers are to be equipped/hunged on with 450 mm long SS telescopic channel with single three way locking system which locks all drawer in single operation.d) All drawers shall have 100 mm size SS handles (one on each drawer). (Note: The item includes cost of all material and labour. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)
21Providing and Placing in Position Working table of required size as per direction & satisfaction of Engineer-in-charge:a) The top of table shall be made with 18 mm thick commercial ply board having 100 mm wide extra board beneath the top to make the overall thickness of 36-38 mm at the edges.b) The vertical supports of full height of 700mm to 750mm and front / modesty of 550 mm to 600 mm height shall be made with 18 mm thick commercial plyboard.c) Table top surface, both faces of vertical sides and Modesty / front shall be finished with 1 mm thick decorative / coloured high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.d) The underside of table shall be finished with 0.65 mm high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.e) Edges of exposed boards/ply shall be finished with PVC Edge bending tape . (For payment purpose TOP surface area/ plan area (maximum dimensions) will be measured). (Note: The item includes cost of all material, labour and necessary cutouts wherever required. The quantity shown in item will be prepared on requirement not at once. Please read Technical Specification of tender document before quoting rate.)
22Providing and Placing in Position fully veneered executive table of required size as per direction & satisfaction of Engineer-in-charge:a) The top of table shall be made with 18 mm thick commercial ply board having 150 mm wide extra board beneath the top to make the overall thickness of 36-38 mm at the edges.b) The vertical supports of full height of 700mm to 750mm and front / modesty of full height shall be made with 18 mm thick commercial plyboard.c) Table top surface, both faces of vertical sides and Modesty / front shall be finished with 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1) (having base price of Rs. 1000/ sqm)d) The underside of table shall be finished with 0.65 mm high pressure laminated sheet of plain /wood grain in matt / suede finish and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.e) Edges of exposed boards/ply shall be finished with 40 x 6 mm teak wood margin for top and vertical sides with 20 x 6 mm teak margin. (For payment purpose TOP surface area/ plan area (maximum dimensions) will be measured. Cost adjustment shall be done in case of any variation in the cost of the veneer actually approved by EIC and used in the work. The agency has to produce GST invoice to establish the actual purchase cost). (Note: The item includes cost of all material, labour and necessary cutouts wherever required. The quantity shown in item will be prepared on requirement not at once.)
23Polishing in high gloss/matt finish melamine clear polish on wood work in required color/ wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/ grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)
24Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with :Decorative veneer facings of approved manufacture
25Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionPolyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)
26Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Polyester powder coated aluminium (minimumthickness of polyester powder coating 50 micron)
27Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)
28Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm
29Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge. Polyester powder coated minimum thickness 50 micron aluminium
30Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete. 255 X 19 mm
31Providing and placing in position Designer Office Centre table, with frame made in 2nd class teak wood. The table to be of size 1050 x 600 x 450 mm with 8 mm bevelled edge glass, duly polished in desired shade in laquaer finish all complete as per the direction and satisfaction of Engineer-in- charge.
32Providing and placing in position Designer Office Corner table, with frame made in 2nd class teak wood. The table to be of size 450 x 450 x 450 mm with 8 mm bevelled edge glass, duly polished in desired shade in laquaer finish all complete as per the direction and satisfaction of Engineer-in- charge.
33Deduct for not providing shutters made with 19 mm thick commercial board i/c inside and outside laminate and to be fixed with 2 / 3 nos. SS butt hinges of size 75X20X25 mm, 100 mm S.S handles (one on each shutter), magnetic catcher, tower bolt and Multi purpose lock in item no. 15 as per the direction and satisfaction of Engineer-in- charge.
34Extra for providing glass shutters made with 8 mm thick float glass and to be fixed with top and bottom pivot, Magnetic Push-to-Open Latches (on each shutter), and Multi purpose lock for glass in item no. 15 as per the direction and satisfaction of Engineer-in- charge.
35Deduct for taking away of aluminium sections, butt hinges, sliding door bolts, tower bolts, lock, handle, door stopper, casement stay, tee chanals, plates etc. and the like received from dismantling. The material so received shall be the property of contractor after dismantling duly weighed/ measured before removing from the site in the presence of Engineer-in-charge or his authorised representative all complete.
36Deduct for taking away of old broken/ damaged wooden storage units having depth upto 600 mm but not less than 300 mm. The material so received shall be the property of contractor after dismantling duly measured before removing from the site in the presence of Engineer-in-charge or his authorised representative all complete. (For measurement purpose Front area to be measured.)
37Deduct for taking away of old broken/ damaged wooden table. The material so received shall be the property of contractor after dismantling duly measured before removing from the site in the presence of Engineer-in-charge or his authorised representative all complete. (For measurement purpose top area to be measured.)
38Deduct for taking away of old broken/ damaged wooden drawer units having approx. size 400(W)X500(D)X600(H)mm. The material so received shall be the property of contractor after dismantling duly counted before removing from the site in the presence of Engineer-in-charge or his authorised representative all complete. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58645996
AUTHORITY Boards / Undertakings / PSU
TENDER VALUE 70.05 Lakhs
LAST DATE 11-12-2026
Authority
Authority Name Airports Authority Of India
Work Description Tender for Miscellaneous Civil & Interior Work For Improvement Of Rajiv Gandhi Bhawan, New Delhi For The Year 2026-27.
Basic Detail
Tender No AAI/CHQ/IMU/Engg(C)/Misc. Civil/2026-27
Bidding Type Tender
Location
City Delhi
State Delhi
Key Dates
Publish Date 20 Nov 2026
Submission Date 11 Dec 2026
Open Date 14 Dec 2026
Finance
Tender Value 70.05 Lakhs
Tender Fee 1180
EMD 2.10 Lakhs
Exemption Not Available
Document List
937b078a-e89a-46a5-a03b-8fad6ace7034.html
BOQ_347777.xls
TD.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 20, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 11, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 19 days
Dec 14, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 22 days

Tender Documents

Download All (ZIP) ↓
html

937b078a-e89a-46a5-a03b-8fad6ace7034.html

xls

BOQ_347777.xls

pdf

TD.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender