Tender For Construction Of Road Along With Drain From Head Of Tanmoy Roy To Head Of Adhir Das At Fokdaibari Under Dabgram-Ii G.P., Rajganj Block
Tender Value
1.11 Crore
Estimated cost
Bid Submission
14 Dec 2026
23 days left
EMD
2.23 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Road Along With Drain From Head Of Tanmoy Roy To Head Of Adhir Das At Fokdaibari Under Dabgram-Ii G.P., Rajganj Block
BOQ
| Sl. No. | Item Description |
| 1 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 2 | 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars |
| 4 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) |
| 5 | Neat cement punning |
| 6 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns |
| 8 | Excavation in Soil with Dozer with lead up to 100 metres Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment up to a distance of 100 metres (average lead 50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections (Reference to MoRT&H's specification clause 301). |
| 9 | Granular Sub-Base with Graded Material (Table:- 400-1)1A Plant Mix Method Construction of granular sub-base byproviding graded material such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading spreading inuniform layers with motor grader onprepared surface, mixing by appropriate mechanical mixure (withcontrolled addition of water), and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 Rate per cum for grading-V Material NB Variety |
| 10 | Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400-13 revised vide table 2 of IRC : 109 (2015) to wet mix macadamspecification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a singlecompacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. NB Variety |
| 11 | Providing and applying tack coat with Cationic bitumen emulsion(RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). ii) On Granular surface treated with primer @ 0.25kg-0.30 /sqm. |
| 12 | Open - Graded Premix Surfacing Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen of approved grade to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled tandem or other approved type roller 8-10 tonne capacity, finished to required level and grades (Reference to MORT&H's specification clause 510). Case - I: Mechanical method usingapproved grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour . |
| 13 | Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511) Case - II : Type B Providing and laying of premix sand seal coat with HMP using approved crushed stone chipping and viscosity grade paving bitumen of suitable approved grade. |
| 14 | Direction and Place Identification Signs with size more than 0.9 sqm size Board. Providing and erecting direction and place identification retroreflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801). |
| 15 | Add GST Factor @ 0.973 and Cost Index factor @ 1.21 from Sl. No. 1 to 7 |
| 16 | Add GST @ 18 % from Sl. No. 8 to 14 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 23 daysDec 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender