Road Transport and Highways Government Departments Closing in 15 days TDR #58644981

Tender For Providing Road Furniture In Sellur Arm For The Work Of Construction Of Flyover At Goripalayam Junction From Goripalayam To Sellur

Issued by Government Departments · Madurai, Tamil Nadu
Tender Value
80.50 Lakhs
Estimated cost
Bid Submission
07 Dec 2026
15 days left
EMD
52000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Madurai → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Providing Road Furniture In Sellur Arm For The Work Of Construction Of Flyover At Goripalayam Junction From Goripalayam To Sellur

BOQ

Name of Work:-
Sl. No. Item Description
1Road Furniture
2Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @250 gms. Per sqm area thickness of 2.5mm is exclusive of surface applied glass beads as per IRC 35. The finished surface to be level , uniform and free from streaks and holes etc., complete (as per MORT&H specification No.803
3Providing and fixing reflective road studs of 'category A' Raised pavement markers made out of poly carbonate / ABS moulded body and reflective panels (bi-convex reflectors) with miicro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro-reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORTH circular No. RW / NH. 33023 / 10 97-DO.III dt. 11.06.97 and the length, height and width of the body shall not be less than 100 mm, 15 mm and 90 mm and base of marker shall be flat within 1.3 mm. The marker shall support a load of 13635 Kg. tested in accordance with ASTM D4280. Lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The area of each retro-reflectory surface shall not be less than 13.0 sq.cm. The slope or retro-reflectory surface shall be 35 + 5 degree to base. Each reflector shall have a CIL not less than values specified in table 2 of said MORT&H circular and two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be provided for better anchorage.
4Providing and Erecting of Retro - Reflectorised Hazard Marker Traffic Sign made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2022 and ASTM D 4956 –09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm and 0.60m below ground level. The sign post should be painted as per IRC 67-2022 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer-in-charge. High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2022. The retro- reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2022. (as per MoRT&H Specification No.801) 30cm x 90cm rectangular
5Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory Signs ( without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67 : 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild Steel angle and supported on a mild steel angle post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm size including cost and conveyance of all materials, eqipment, machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge, High intensity Retro - Relectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 (as per MORT&H Specification No.801)
660 Cm Circular (Without Definition Board)
790 Cm Triangular (Without Definition Board)
890 Cm Octagon (Without Definition Board)
960 X 45 Cm Chavaran
10Supplying and installation of delineators (road way indicators, hazard markers and object markers),80-100 cm high above ground level, painted at alternatively black and white in 15 cm wide strips,fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 etc., complete (as per MoRT&H specification No. 806)( head light cutter)
11Providing and Fixing of Flexible Median Marker that made of tough, high impact resistant, injection- molded, thermoplastic body with property of flexibility to provide high durability. The dimension of Flexible Median Marker should not exceed 18.4 cm in height(including shank height),12.5 Cm in width. 0.65 cm in thickness and shank depth shall be 3.4 cm The body structure shall be rounded at all its corners and edges. The plastic used for molding the Flexible Median Marker should survive impact load of 5kg continuously for 750 times at room temperature. The logo of the manufacturer shall be embossed on either side of the body in the injection molding process. The Median Marker shall have flame like shaped body with, fluorescent yellow color retro- reflective sheeting of size not less than 90 Cm square,with fully reflective micro prismatic cube corners as its retro-reflective elements as per IRC 67 2012 and ASTM D4956-09 type XI specifications reflectivity values. The retro-reflective sheeting shall be one or both sides of the Flexible Median Marker and shall be edge protected with no exposed edges which will prevent edge lifting, vandalism, sheeting damage, etc., The Flexible Median Marker shall be fixed by a combination of epoxy adhesive and grouting as recommended by manufacturer.
12Proving and fixing Solar powered Traffic Blinkers of 30cm dia with Polycarbonate Dome 5mm Red of Led 150 Nos.iri each Red Blinkers Light - 1 No. with Red / White /Blue Led Blinkers Delineator Solar Panel : 12v 50w SolarPanel — 1 No. 12v 18 AH Battery -1 No. with Box, Solar Circuit Controller Board Box. Straight Pole : MSPole 3” dia 2.5mm thick 18 Feet height pole (1 No.) with 2 Feet under ground pole foundation, pole painting including transportation charges, installation charges etc., complete as per standard specification.
13Rubber Speed breaker of size 75mm thick withreflectors including cost, conveyance and all otherincidental charges etc., complete as per standardspecification
14Providing and erecting Direction and Place Identification Retro-reflectorised Sign made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67 : 2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild Steel angle and supported on a mild steel angle post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm size including cost and conveyance of all materials, eqipment, machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge, High intensity Retro - Relectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 (as per MORT&H Specification No.801)
15Providing and fixing of Digitally Printed Retro Reflectorized Overhead Cantilever Informatory sign Board of Size 5.00m x 1.80m made of cube corner MicroPrismatic grade sheeting conforming to Type XI standards of IRC 67 - 2022 and ASTMD4956 – 09, specification and fixed over 2mm thick aluminum sheet fixed on back supporting frame mild steel L angle of size 50mm x 50mm x 6mm. The Vertical support post for the installation of overhead sign Gantry shall be made of 300NB (Nominal Bore) MS Pipe with 12mm thick with a ground clearance of 6 meters along with 80NB (Nominal Bore) MS Pipe with 4mm thick and 40NB (Nominal Bore) MS Pipe with 3.20mm thick support posts. MS Base plate of size 1200mm x 1200mm x 25mm and MS Top plate of size 900mm x 1650mm x 16mm to be used to hold the sign board at the top and bottom respectively. MS Stiffener plates 8mm thick of sizes 420x420, 682x420, 288x288, 288x927 & 44x130 are to be used. Anchor bolts of dimension 25mm dia and 1000mm length are to be used as fixtures. The approved direction information should be digitally printed and should have 70% of the co-efficient of Retro-reflection values against the values as mentioned in Table 6.9 of IRC 67 – 2022. The Latex printer used for digital printing should use inks with low VOC emissions and have green guard, eco logo certificates as per UL 2801 standards. The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance and a certified copy of three years Outdoor exposure report shall be obtained as per IRC 67-2022 (As per MoRT&H specification No.801). Cantilever sign shall be installed at the site as per the approved structural and foundation drawing provided in the tender document and including cost and conveyance of all materials, equipment, machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer-in-charge etc., complete.
16Calculation of SubTotal, GST and Total Amount carried out by system automatically
17Basic cost of value put to tender as per estimate
18Add GST at 18%
19Total Value put to Tender
20Quoted Percentage
21Quoted Value
22Add GST at 18% of Final Quoted Value
23Total Value of Contract Including 18% of GST Basic cost of value put to tender as per Estimate Please Enable Macros to View BoQ information
24Total Value of Contract Including 18% of GST Basic cost of value put to tender as per Estimate Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58644981
AUTHORITY Government Departments
TENDER VALUE 80.50 Lakhs
LAST DATE 07-12-2026
Authority
Authority Name Highways Department
Work Description Tender for Providing Road Furniture In Sellur Arm For The Work Of Construction Of Flyover At Goripalayam Junction From Goripalayam To Sellur
Basic Detail
Tender No MDU 004/Madurai-I Division/Goripalayam Sub work RF/TN No 04/2026 27/ HDO/Dated 12.11.2026
Bidding Type Tender
Location
City Madurai
State Tamil Nadu
Key Dates
Publish Date 20 Nov 2026
Submission Date 07 Dec 2026
Open Date 07 Dec 2026
Finance
Tender Value 80.50 Lakhs
Tender Fee Ref. Documents
EMD 52000
Exemption Not Available
Document List
90e2bccf-4cd4-4466-aa9f-8b0e3d43238d.html
BOQ_874956.xls
Tendernotice_1.pdf
Tndoc004.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 20, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 07, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 15 days
Dec 07, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 15 days

Tender Documents

Download All (ZIP) ↓
html

90e2bccf-4cd4-4466-aa9f-8b0e3d43238d.html

xls

BOQ_874956.xls

pdf

Tendernotice_1.pdf

pdf

Tndoc004.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender