Defence Statutory Bodies & Commissions/Committees Closing in 20 days TDR #58641035

Tender For Repair/Maint Of Kitchen Cabinet And Other Connected Work Of Offrs/Jcos Md Accn At Mil Stn Dappar Under Age(I) Dappar.

Issued by Statutory Bodies & Commissions/Committees · S.a.s Nagar, Punjab
Tender Value
Ref. Documents
Estimated cost
Bid Submission
12 Dec 2026
20 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
S.a.s Nagar → Punjab
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Repair/Maint Of Kitchen Cabinet And Other Connected Work Of Offrs/Jcos Md Accn At Mil Stn Dappar Under Age(I) Dappar.

BOQ

Name of Work:- REPAIR/MAINT OF KITCHEN CABINET AND OTHER CONNECTED WORK OF OFFRS/JCOS MD ACCN AT MIL STN DAPPAR UNDER AGE(I) DAPPAR.
Sl. No. Item Description
1Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.
2Material and labour for rendering 5mm thick in cement mortar (1:3) on concrete surface of ceiling, finished fair, even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.
3Material and labour for rendering 10mm thick in cement mortar (1:6) on fair faces of Brick walls or concrete surfaces, finishing the surface fair and even complete all as specified and as directed by the Engineer-in-Charge.
4Material and labour for Preparation of new plastered wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty 1.5mm thick in two layers on complete surface and smoothening the surfcae with sand papers/by Mechanical method (hand electric grinder) prepatory to paint as directed. (b) Two coats of distemper oil emulsion (exterior) of approved tint/shade (Company Depot Tinted) over a coat of primer (exterior) by using paint Roller.
5Material and labour for preparing new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.
6Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.
7Material and labour for joint free non-Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed bedding layer in CM 1:6, complete all as specified and directed.
8Material and labour for Non skid coloured Ceramic tiles 7 to 8mm thick area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over 10mm thick rendering CM (1:4) complete all as specified. complete all as specified.
9Material and labour for glazed ceramic coloured tiles in vertical surfaces such as skirting, dados and riser to steps etc size 250mmx350mmx7mm /450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over including 10mm thick rendering CM (1:4), complete all as specified and directed.
10Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.
11Material and labour for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.
12Providing Granite stone any description edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.
13Taking down shutters only of any description area exceeding 1.00 sqm and not exceeding 2.00 sqm each and removing from site complete all as specified and as directed by Engineer-in- charge.
14Supply & fixing factory made gauged and skeleton shutter 35mm thick made out of 2nd class hard wood kiln seasoned and chemically pressure treated, open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, fitted with cut and mitred beads for securing glass, gauze etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); complete all as specified and as directed by Engineer-in- charge.Note: Glass gauze shall be measured and paid tor separately
15Supply and fixing for butt hinge ISI Marked 100mm size, medium weight, cold rolled mild steel, complete all as specified and directed.
16Supply and fixing for 150mm aluminium handles, cast type, anodised, complete all as specified and as directed by the Engineer-in-Charge.
17Supply and fixing for 150mm long aluminium, anodized, barrel tower bolts of extruded section, complete all as specified and as directed by the Engineer-in-Charge.
18Supply and fix Galvanised mild steel wire cloth thickness 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed.
19Supply and fix in repairGalvanised mild steel wire cloth thickness 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed.
20Supply and fix in repair 3mm thick sheet glass ordinary quality and glazing with oil putty/screws/nails in squares not exc 0.5 Sqm in each pane complete all as specified and directed including hacking out old glass, complete all as specified and directed.
21Supply and fix in repair 3mm thick figured glass oilputty/ pinched type in squares not exc 0.5 sqm each pane including hacking out old glass, complete all as specified and directed by Engr-in- charge.
22Supply and fix 150mm Aluminium alloy , anodised , sliding door bolt with hasp , staple (bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium, alloy and fixed, complete all as specified and directed.
23Supply and fix 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate fixed, complete all as specified and directed.
24Supply and fix in repairs 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate fixed, complete all as specified and directed.
25Material and labour for preparing new wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.
26Supply and fix in repair stainless steel sink with drainage board, 1.00 mm thick, glossy finish, for kitchen with plugs washers and CP waste coupling/round strainer of 110mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 915mm x460 with bowl size 410x 330 x 160 and making good disturbed portion in CM 1:3 or PCC 1:2:4, complete all as specified and directed.
27Dismantling of boarding of any type/size as in CB/wardrobes or fixed in any position in hardware (if any) etc, complete all as specified and directed.
28Material and labour for plain fillets as in 2nd class hard wood square rectangular in section wrought secured with screws sectional area exc 6 but not exc 13 Sqcm, Complete all as specified and directed.
29Supply and fix factory made 18mm thick solid WPC (wood polymer composite) board of density 650kg/cum of one side prelaminated/rigidlam with any colourn and other side balancing lamination, as in cupboards/kitchen/ cabinet shutter/ drawers etc fixed with screws, sovent cement, adhesive including dismantling old existing board, complete all as specified and directed.
30Material and labour Prelaminated particle board,18/19 mm thcik both side interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed.
31Supply and fix Piano/continuous hinge of size 40mm (when open) stainless steel, complete all as specified and directed.
32Supplying and fix in repair position Soft Close Full Overlay Concealed Cabinet Hinges, 4-hole type, nickel plated finish, having 105 degree opening angle suitable for 14-20mm thick board, including cutting necessary recess in shutter, fixing with necessary screws, complete all as specified and directed of Engr-in-Charge.
33Supply and fix 100mm Brass handles, cast type,polished bright complete all as specified and as directed by the Engineer-in-Charge.
34Supply and fix heavy duty double magnetic catcher, size 45mm to 50mm long, brown/white colour, with powerful magnet and MS striker plate, fixed with screws complete for cupboard/wardrobe shutters, complete all as specified and directed.
35Supply and fix in repair harrision rail stainless steel tubing of 25mm dia chromium plated 1.6 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets fency type, stops etc, complete all as specified and directedNote : For the purpose of mesurement and payment running length of curtain rod only shall be considered.
36Supply and fix 125mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58641035
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE Ref. Documents
LAST DATE 12-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for Repair/Maint Of Kitchen Cabinet And Other Connected Work Of Offrs/Jcos Md Accn At Mil Stn Dappar Under Age(I) Dappar.
Basic Detail
Tender No CA No AGE(I)/DPR/T-24/2026-27
Bidding Type Tender
Location
City S.a.s Nagar
State Punjab
Key Dates
Publish Date 20 Nov 2026
Submission Date 12 Dec 2026
Open Date 14 Dec 2026
Finance
Tender Value Ref. Documents
Tender Fee 500
EMD 40000
Exemption Available
Document List
2118214e-04a3-44af-bb6d-cd35b5019d53.html
BOQ_897277.xls
Tendernotice_1.pdf
Tendert24.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 20, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 12, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 20 days
Dec 14, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 22 days

Tender Documents

Download All (ZIP) ↓
html

2118214e-04a3-44af-bb6d-cd35b5019d53.html

xls

BOQ_897277.xls

pdf

Tendernotice_1.pdf

pdf

Tendert24.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender