Tender For Improvement Of Rws Schemes By Providing Pressure Filter In Village Panchayat Barcem Quedem Of Quepem Constituency.
Tender Value
65.99 Lakhs
Estimated cost
Bid Submission
27 Nov 2026
5 days left
EMD
1.31 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Of Rws Schemes By Providing Pressure Filter In Village Panchayat Barcem Quedem Of Quepem Constituency.
BOQ
| Sl. No. | Item Description |
| 1 | Providing, installing & commissioning of aqua catalytic oxidation filtration systems (pressure filter) having flow rate 5000 lit/hr and working pressure of 1.5 kg/cm2 to 5 kg/cm2 including connecting to rising main with a maximum / minimum operating pressure of 8.0 Bar and 3.0 Bar respectively and including the cost of filter unit, inlet valve, outlet valve, bypass valve and non return valve, MS stand for support and confirming to specifications as mentioned below. The downstream should not have any suspended particles greater than 80 microns size. The filter equipment should be of Carbon Steel 37-2 with one inlet, one outlet and drain and the system should consist of coarse screen and fine screen. The system should consist of Zeosorb (cwg Germany) multi-grade pressure filter (1 No.) with required accessories for connecting the filter to rising main with a maximum / minimum operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively to filter water containing suspended solids and confirming to the following specifications |
| 2 | Activated carbon multigrade pressure filter (1 No) with required accessories for connecting the filter to rising main with a maximum / minimum operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively to filter water containing suspended solids and confirming to the following specifications. The vertical cylindrical shell with dish ends should be made up of mild steel confirming to IS 2062 fabricated of plate thickness 6 mm and dish end thickness 6 mm the inner surface of M.S. Shell should be provided with epoxy paint with the raw material confirming to FDA standards. Protective coat of red oxide primer and enamel paint as per IS – 14209 for outer surface of the M.S. Shell should be provided.The specifications of vessels and other fixtures should be as under One number of filter vessel for zeosorb having diameter 600mm One number of filter vessel for carbonsorb having diameter 600mm Frontal pipeline of 50 mm dia Valves of multiport P P valve Shell thickness of 6 mm and dish end thickness:6 mm Filter media of zeosorb (cwg Germany), activated carbon, silica sand. One number of chlorine dosing pump Two number of pressure relief valve Two number of pressure gauge dial MOC of vessel MS IS 2062. |
| 3 | Providing, installing & commissioning of aqua catalytic oxidation filtration systems (pressure filter) having flow rate 10000 lit/hr and working pressure of 1.5 kg/cm2 to 5 kg/cm2 including connecting to rising main with a maximum / minimum operating pressure of 8.0 Bar and 3.0 Bar respectively and including the cost of filter unit, inlet valve, outlet valve, bypass valve and non return valve, MS stand for support and confirming to specifications as mentioned below. The downstream should not have any suspended particles greater than 80 microns size. The filter equipment should be of Carbon Steel 37-2 with one inlet, one outlet and drain and the system should consist of coarse screen and fine screen. The system should consist ofZeosorb (cwg Germany) multi-grade pressure filter (1 No.) with required accessories for connecting the filter to rising main with a maximum / minimum operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively to filter water containing suspended solids and confirming to the following specifications. |
| 4 | Activated carbon multigrade pressure filter (1 No) with required accessories for connecting the filter to rising main with a maximum / minimum operating pressure of 3.5 Kg/ cm2 to 2.0 Kg / cm2 respectively to filter water containing suspended solids and confirming to the following specifications. The vertical cylindrical shell with dish ends should be made up of mild steel confirming to IS 2062 fabricated of plate thickness 6 mm and dish end thickness 6 mm the inner surface of M.S. Shell should be provided with epoxy paint with the raw material confirming to FDA standards. Protective coat of red oxide primer and enamel paint as per IS – 14209 for outer surface of the M.S. Shell should be provided.The specifications of vessels and other fixtures should be as under One number of filter vessel for zeosorb having diameter 1000mm One number of filter vessel for carbonsorb having diameter 1000mm Frontal pipeline of 50 mm dia Valves of 2 inch dia butterfly valve Shell thickness of 6 mm and dish end thickness:6 mm Filter media of zeosorb (cwg Germany), activated carbon, silica sand. One number of chlorine dosing pump Two number of pressure relief valve Two number of pressure gauge dial MOC of vessel MS IS 2062. |
| 5 | Earth work in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches, drain not exceeding 1.5m in width 10 sq.m on plan including dressing of sides ramming of bottoms for all lead and lift including setting out the excavated soil & disposal of surplus soil with all lead including providing barricading danger lighting guarding as directed by departmental officer in all types strata comprising any of the materials such as soil, silt sand clay gravel moorum of all conglomerated laterite rock, soft rock fissured shattered decomposed rock or weathered rock and all such other materials as described under Appendix A to these specification either in full or in parts as the case may be adopting any approved method of methods as may be convenient or permitted inclusive of chiselling, wedging etc, blasting prohibited in all conglomerates as directed by the Engineer-in-charge etc, complete. |
| 6 | Supplying and filling in plinth under floors trenches including watering ramming consolidating dressing complete. |
| 7 | Moorum |
| 8 | Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete. |
| 9 | Laterite masonry in neatly dressed stones for 23 cms thick masonry walls in cm. 1 : 5 (1 cement : 5 coarse sand) in foundation upto plinth level |
| 10 | Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering shuttering and finishing in: |
| 11 | All works upto plinth level |
| 12 | Providing and fixing 1 mm thick M.S. sheet garage door with frame of 40 x 40 x 6 mm angle iron 3.15 mm M.S. gusset plate at the junction and corners all necessary fitting complete including applying a priming coat of red lead paint. |
| 13 | Using M.S. angles 40 mm x 40 mm x 6 mm for diagonal braces. |
| 14 | Steel work in built up tubular (round square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL TATA. VIZAG JSW APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc. including cutting hoisting fixing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washers etc. complete. |
| 15 | 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge. |
| 16 | Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins rafters trusses flashings etc. complete as per the directions of the Engineer in charge. |
| 17 | Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade |
| 18 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 19 | Finishing wall with waterproofing cement paint of approved brand and manufacture and of required shade on new work (three or more coats) to give an even shade. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender