Tender For Addition / Altration / Improvement To Certain Smq And Associated Works At Agra
Tender Value
9.86 Crore
Estimated cost
Bid Submission
25 Dec 2026
33 days left
EMD
8.20 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Agra → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition / Altration / Improvement To Certain Smq And Associated Works At Agra
BOQ
| Sl. No. | Item Description |
| 1 | BUILDING WORK (REPAIR) |
| 2 | Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and as directed. |
| 3 | Material & Labour for brick work with burnt clay old size sub class B Bricks, straight or curved on plan with mean radius n.exc 6m built in Cement Mortar 1:6. complete alll as specified and as directed |
| 4 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and as directed. |
| 5 | Demoltion of reinforced cement concrete in Roofs floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed. |
| 6 | Material & Labour for Nominal Mix RCC M-20, type A-1, 1:1.5:3 ratio, using crushed stone aggragates of 20mm nominal size for slabs supported on walls complete all as specified and as directed. |
| 7 | Material & Labour RCC 1:2:4, type B-1, using 20mm crushed stone graded aggragate for slabs supported on walls complete all as specified and as directed. |
| 8 | Material & Labour for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work with fair finished surface; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed. |
| 9 | Material & Labour for non skid ceramic coloured tiles 8 to 10 mm thick (square or rectangular) in floors, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer 15 mm thick in cement mortar 1:6 complete all as specified and as directed. |
| 10 | Material & Labour for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) in floors, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer 15 mm thick in cement mortar 1:6 complete all as specified and as directed. |
| 11 | Material & Labour for glazed ceramic coloured tiles on vertical surfaces, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:4 on other than fair faces of brick wall finished rough to fix tiles complete all as specified and as directed. |
| 12 | Material & Labour for glazed ceramic coloured tiles of size 450 x 300 x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:4 on other than fair faces of brick wall finished rough to fix tiles complete all as specified and as directed. |
| 13 | Material & Labour for pre-polished machine cut Kota stone in stair case tread flooring 20-25mm thick laid over 20mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. (Note : Single stone piece without joint on one tread with nosing one side shall be provided) |
| 14 | Material & Labour for pre-polished machine cut Kota stone slab in stair case riser 20-25mm thick on vertical surfaces over 10mm thick cement mortar 1:4 such as risers, skirting etc. jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and taking down existing skirting complete all as specified and as directed. (Note : Single stone piece without joint on one riser shall be provided) |
| 15 | Taking down cement or cement lime plaster on walls any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and as directed. |
| 16 | Material & Labour for rendering 15 mm thick in cement mortar 1:4 mixed with Pidi Proof 101 LW (+) of Dr fixit or equivalent integral water proofing admixture @200 ml/bag of cement and finish the surafce even and smooth (without using extra cement ) complete all as specified and as directed. Note: Pidi proof to be measured separately as supply only. |
| 17 | Material & Labour for applying two coats of super latex 302 of Dr fixit (Pidilite) or equivalent in ratio (1:4:7) (one part super latex 4part water 7 parts of cement ) @1.5 Kg of homogenous mixutre /Sqm complete all as specified and as directed. |
| 18 | Material & Labour for Washed stone grit plaster on exterior walls in two layers, under layer 12mm thick cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm thick cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 with stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings, colour patterns of stone chippings shall be same as adjacent existing surface and as approved by GE including taking out existing stone grit & plaster complete all as specified and as directed. (Payment for providing grooves shall be made separately). |
| 19 | Material & Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finishing the surafce even and smooth (without using extra cement ) complete all as specified and as directed. |
| 20 | Supply only Pidi proof 101 LW (+) of Dr Fixit (Pidilite) or equivalent of make latex/ CICO No.1/ Fosroc (India) Ltd. complete all as specified and as directed. |
| 21 | Material & Labour for scraping out loose mortar / concrete by chiseling / wire brushing complete and applying rust removing solution (rebaklene soulution) to exposed corroded reinforcement and applying a coat of epoxy primer (Nitozink primer from M/s Fosroc or equivalent as approved by GE) as per manufacture instructions providing and fixing of wire mesh of weight 2.5 Kg per Sqm and apply 25mm thick plaster of average thickness in cement mortar 1:4 mixed with liquid integral water proofing compound (complast 'X' as per manufacture instructions) with gunitting machine at a pressure not less than 5Kg/Sqcm finally rendering 10mm thick plaster in cement mortar 1:4 using liquid integral water proofing compound (complast 'X' 421 i.e. from M/s Fosroc and nitobound or from M/s Fosroc or equivalent as approved by GE) in the proportion recommended by the manfacture including three coats of white wash complete all as specifed & as directed. Note :- The Rates are inclding Use of all scaffoldings up to 14 M ht of buildings . |
| 22 | Material & Labour for rendering 10 mm thick in cement mortar 1:3 on concrete surface of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed. |
| 23 | Material & Labour for preperation of newly plastered concrete surface of ceiling & applying three coat of white wash on ceiling surface complete all as specified and as directed. |
| 24 | Material & Labour two coats of distemper oil emulsion on newly plastered wall surfaces including preparation and 1mm thick wall care putty complete all as specified and as directed. |
| 25 | Material & Labour for applying two coats of white wash on new plastered or unplastered surfaces of wall including preparation of surface complete all as specified and as directed. |
| 26 | Material & Labour for applying two coats of white wash on old plastered or unplastered surfaces of ceiling surface including preparation of surface complete all as specified and as directed. |
| 27 | Material & Labour for applying two coats of white wash on old plastered or unplastered surfaces of wall including preparation of surface complete all as specified and directed. |
| 28 | Material & Labour preparing old decorated surface of walls and applying two coats of distemper oil emulsion with 1 mm thick wall care putty to make smooth surface including complete removal of existing treatment on walls complete all as specified and as directed. |
| 29 | Preparing surfaces plastered or unplastered surfaces of wall by complete removal of existing treatment for old surfaces complete all as specified and as directed. |
| 30 | Preparing of new plastered surfaces complete all specified and as directed. |
| 31 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 32 | Providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 33 | Taking down existing roof treatment of any type and any thickness including, tarfelt, APP, mud in roofs, plastering, leeping plaster of any thickness cutting & uprooting trees roots/Vegetation growth & removing the debris from the premises upto 500m from the MOD land complete all as specified and as directed. |
| 34 | Demolition of plain cement concrete (unreinforced) of any description and any position not otherwise specifically provided for as specified and as directed. |
| 35 | Material & Labour for 10mm thick screed bed with cement mortar 1:4 in roof surface including Pidi Proof 101 LW (+) of Dr fixit or equivalent integral water proofing liquid @200 ml/bag of cement complete all a specified and as directed. (Note-Integral water proofing compound shall be measured and paid separately under respective item) |
| 36 | Material & Labour for Providing plain cement concrete Type B1 (1:2:4) (20 mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, levelling course, roof padding on RCC roof slab or terrace with using WPC @ 2% mix by weight of cement finising even and smooth complete all as specified and as directed. |
| 37 | Material & Labour for water proofing treatment to roof/ sunken roof with APP based polymeric membrane 3mm minimum consisting of 90-100 micron thick central core of HMHDP film and standard weight of 3.00 kg/sqm reinforced with polyster non woven fabric (weighing not less than 160gm/sqm shall be applied over and including apllying a coat of hot blown bitumen 85/25 confirming to IS 702 @1.20 Kg/sqm over a coat of bituminous primer @ 0.30 ltrs/sqm application of APP modified membrane and joint shall be by torch application . The overlaps shall be minimum 100mm on transverse direction and 75 on longitudnal direction complete all as specified and as directed. |
| 38 | Material & Labour for 30cm X 30cm X 20mm thick PCC tiles, machine pressed factory made as per IS-1237-1980 (ISI marked) laid over 20mm thick screed bedding in cement mortar (1:4) mixed with water proofing liquid @ 5% by weight of cement and tiles joints shall be filled with polymer based cement proof joint filler manufactured by approved company including dismantling of tiles complete all as specified and as directed. (Note- water proofing liquid shall be measured and paid separately under respective item) |
| 39 | Material & Labour for cutting grooves in brick parapet walls, 75mm wide and 65mm deep and shaping horizontal face of groove for inserting APP membrane and sealed complete all as specified and as directed |
| 40 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed. |
| 41 | Material & Labour for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and the like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite stone over screed bed 10mm thick in cement mortar 1:4 including moulding of edges complete all as specified and as directed. |
| 42 | Demolition of PCC in ground floors & pavings n.exc 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and as directed. |
| 43 | Material & Labour for 75mm thick cement concrete type C-2 (1:3:6) (using 40 mm graded stone aggregate ) as in plinth protection and path finished even and smooth without using extra cement complete all as specified and as directed. |
| 44 | Material & Labour for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 45 | Material & Labour Mild Steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed. |
| 46 | Taking up or down steel water tubing and connections including cleaning for refixing or removal to store 15mm bore complete all as specified and as directed. |
| 47 | Taking up or down steel water tubing and connections including cleaning for refixing or removal to store 20mm bore complete all as specified and as directed. |
| 48 | Taking up or down steel water tubing and connections including cleaning for refixing or removal to store 25mm bore complete all as specified and as directed. |
| 49 | Supplying and laying of CPVC pipes in repair 20mm dia external SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified and as directed. |
| 50 | Supplying and laying of CPVC pipes in repair 25mm dia external SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified and as directed. |
| 51 | Supply & Fixing in repair 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC with and including 600 mm long PVC connection with 02 Nos PTMT nuts and rubber washer and making good to disturbed surfaces of wall or floor complete all as specified and as directed. |
| 52 | Supply & Fixing in repair stainless steel sink with drainage board made out of stainless steel 1.00mm thick sheet for kitchen with plugs, washers and waste, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting unions to pipe over all size 915mmx460mm with bowl size 410mmx330mmx160mm complete all as specified & as directed. |
| 53 | Supply & Fixing 32/40 mm dia Semi Rigid PVC waste pipe for wash basin with length not less than 700 mm complete all as specified & as directed. |
| 54 | Supply & Fixing in repair stop valves/angle valve 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and as directed. |
| 55 | Supply & Fixing in repair bib taps, cast copper alloy, fancy type, long body chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and as directed. |
| 56 | Supply & Fixing in repair for vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, with new trap and to flushing pipe, anti-syphonage pipe etc complete including demilition of PCC / Lime concrete bedding of existing pan and making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast with cement mortar complete all as specified and as directed. |
| 57 | Supply & Fixing in repair Viterous China wash down water closet pan (pedestal pattern) with 'P' or 'S' trap, white (excluding fixing bolts, flushing cistern and flush pipe) and including Plastic water closet seat cover white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe superior quality with 1.25 m long flexible pipe and ABS wall hook including making connections and fixed in position complete all as specified and as directed. |
| 58 | Supply & Fixing in repair vitreous china wash hand basin white flat back size 550x400 mm including two Nos angle iron brackets including, 32mm dia PTMT waste coupling, and 600 mm long PVC connection with 02 Nos PTMT nuts and rubber washer complete all as specified and as directed. |
| 59 | Supply & Fixing in repair PVC connections hot and cold 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed. |
| 60 | Supply & Fixing in repair brass chromium plated shower roses with or without swivel joints 125mm size with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed. |
| 61 | Supply & Fixing in repair Chromium plated 20mm dia, D type, 60cm long towel rail with towel racks fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190gms) complete all as specified and as directed. |
| 62 | Supply & Fixing in repair CP grating 100 mm dia with or without hole complete all as specified and as directed. |
| 63 | Supply & Fixing in repair brass CP wall/sink mixer for mixing Hot & cold water screwed down for iron pipe 15mm bore complete all as specified and as directed. |
| 64 | Supply & Fixing in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed. |
| 65 | Supply & Fixing in repair Towel Ring of CP fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and as directed.. |
| 66 | Supply & Fixing in repair position rotational moulded polyethylene triple layered water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position with and including ball valve 20 mm bore high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 210 grams) and dismatling of exisitng tank complete all as specified and as directed. |
| 67 | Supply & Fixing in repair position rotational moulded polyethylene triple layered water storage tanks 500 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position with and including ball valve 20 mm bore high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 210 grams) and dismatling of exisitng tank complete all as specified and as directed. |
| 68 | Supply & Fixing in repair Gun-metal globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and as directed. |
| 69 | Supply & Fixing in repair 600mmx450mm bevelled edge mirror of selected quality glass CP brass screws & cup washers complete all as specified and as directed. |
| 70 | Supply & Fixing plate rack with racks and guard bars made out of stainless steel minimum 1mm thick, over all size 750mm X 600mm X250mm and assembled with using brass nuts, bolts and washers complete all as specified and as directed. |
| 71 | Supply & Fixing sheet glass corner self (Set of 3 tier ) assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated bracket guard and rail and fixed with CP screws and wood cleats with wall complete all as specified and as directed. |
| 72 | Supply & Fixing in repair Brass CP mixer for mixing hot & cold water screwed down (15mm) for iron pipe and fixed for wash basin complete all as specified and as directed. |
| 73 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames size exc. 1.5 sqm but n.exc 4 sqm complete all as specified and as directed. |
| 74 | Taking down chowkhat with shutter (without taking off shutter from the frame) size n.exc 1.5 sqm complete all as specified and as directed. |
| 75 | Supply & Fixing factory made solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in door opening but single sideprelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheetas per specification and drawings complete all as specified and as directed . |
| 76 | Supply & Fixing factory made PVC door frame of the size 50mm x 95mm with a wall thickness of 5mm (+ 0.5mm) made out of extruded 5mm (+ 0.5mm) prelam PVC foam sheet of any colour density 600Kg/cum manufactured by an ISO-9000 certified company, mitre cut at two corners and joined with PVC welding. The two verticals door frames are to be reinforced with 19mm MS tube of 19 gauge throughout the frame, the door and frame shall be fixed to the wall using 75/100mm long MS screws through the frame by using PVC fasteners. A minium of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per manufacturers specification and as per direction. |
| 77 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant. complete as per manufacturers specification and as per direction. |
| 78 | Supply & Fixing factory made solid panel PVC door shutter 30mm thick (style ) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded colour plain PVC or channel having a PVC sheet strip of 20mm width stuch in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 79 | All as per item above but both side prelam PVC sheet used instead of plain colour PVC sheet. Style and rails feathered at edges complete all as specified and as directed. |
| 80 | Supply & Fixing factory made WPC cupboard shutter /shelf / partition of required size, consisting of panel of 18mm (+ 0.70mm ) thick celuka PVC ply and for supportingthe hold of shelf / partition and shall provided 3 edges in size 18mm x 18mm as per required length. The front side of the edge vigible in the front of the shelf / partition to be edge lipped by 18mm x 1mm PVC sheet of density 600 kg / cbm manufactured by an ISO-9000 certified co., using solvent cement etc complete all as specified and directed. |
| 81 | Supply & Fixing 35 mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed. |
| 82 | Supply & Fixing 35mm thk 2nd class Hard wood Kiln seasoned and chemically pressure treated glazed & skeleton shutters, open rebated at prepared to receive glass/gauze (without sash bars) edges of framing plain, chamfered, or rounded, fitted with and incl cut and mitred beads for securing glass, gauge etc, size of members of shutters as specified in SSR Pt-I, Sec-8, clause 8.24 (a) fixed to chowkhats complete all as specified and directed. |
| 83 | Supply & Fixing magnetic catcher of approved quality in cub board and kitchen cabinet including fixing with necessary screws double strips (horizontal type ) complete all as specified and directed. |
| 84 | Material & Labour for powder coated (any colour) anodized aluminium (sliding type) windows with three track bottom track size 92X29.5X1.5mm thick side and top track frame size 92X29.5X1.5mm and shutters powder coated aluminium anodized 39X20X2 mm thick (02 of glass and 01 of SS wire cloth) including necessry aluminium fittings like joint cleat glazing and gauging clips/strips and rubber packing anodized aluminium snap beading screws etc with 5mm thick tinned glass/SS wire mesh with etc including all fittingSupply & Fixingixture complete all as specified and directed. |
| 85 | Supply & Fixing Framed work such as grills with making provision in grills for openable for desert cooler etc, gratings, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 86 | Supply & Fixing powder coated (any colour) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thickness of powder coating 50 micron). |
| 87 | Supply & Fixing powder coated (any colour) anodised aluminium ventilator shutters, top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified (Thickness or powder coating not less than 50 micron). |
| 88 | Supply & Fixing 5mm thick figured sheet glass pane n.exc.0.50 sqm in each pane of selected quality fixing with glazing clips/strips in windows/ventilators shutters complete all as spd and directed. |
| 89 | Supply & Fixing Tinted glass selected quality and glazing with oil putty 5mm thick as specified and directed. |
| 90 | Supply & Fixing Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with gauging clip/strip complete all as spd and directed. |
| 91 | Supply & Fixing Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering including hold fast. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging and fastening etc confirming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and as directed. |
| 92 | Material & Labour for PCC (1:3:6) type C-1 with using 20mm graded stone aggregated as in cill, step and for inserting hold fast of doors and windows all as specified and as directed. |
| 93 | Supply & Fixing 100 mm long medium weight, mild steel hinges. complete all as specified and as directed. |
| 94 | Supply & Fixing 100 mm long medium weight, stain less steel hinges. complete all as specified and as directed. |
| 95 | Supply & Fixing aluminum anodized barrel tower bolt of extruded section size of bolt 150mm complete all as specified and as directed. |
| 96 | Supply & Fixing aluminum handle cast type anodized 150 mm size complete all as specified and as directed. |
| 97 | Supply & Fixing aluminium handle cast type anodized 125 mm size for kitchen cabinet and bed room cupboard shutter complete all as specified and as directed. |
| 98 | Supply & Fixing Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) is 30 mm complete all as specified and as directed. |
| 99 | Supply & Fixing for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed. |
| 100 | Material & Labour for brass Locks for cupboard of grade I, size 65mm 2 levers complete all as specified and as directed. |
| 101 | Material & Labour for two coat of synthtic enamel paint over a coat of primer on new woden surface including preparation of new surfaces of any description, over 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and as directed. |
| 102 | Supply & Fixing Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and as directed. |
| 103 | Demolition and breaking up rain water pipe (PVC, AC, or re-inforced concrete ) of size 100mm complete all as specified and as directed. |
| 104 | Supply & Fixing PVC SWR pipes 110mm dia single socketed in any length with rubber ring joints fixed to wall complete all as specified and as directed. |
| 105 | Supply & Fixing 110mm bore PVC (SWR) bends any radius complete all as specified and as directed. |
| 106 | Supply & Fixing PVC SWR pipes 50mm dia single socketed in any length with rubber ging joints fixed to wall complete all as specified and as directed. |
| 107 | Dismantling of cast iron pipe of 100 mm bore, set in cement mortar complete all as specified and as directed. |
| 108 | Supply & Fixing PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to trench or floor complete all as specified and as directed. |
| 109 | Dismantling of cast iron pipe of 75 mm bore, set in cement mortar complete all as specified and as directed. |
| 110 | Supply & Fixing PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed. |
| 111 | Supply & Fixing in repair PVC (SWR) bends 75mm dia complete all as specified and as directed. |
| 112 | Supply & Fixing in repair PVC (SWR) vent cowl110mm dia complete all as specified and as directed. |
| 113 | Supply & Fixing in repair PVC (SWR) vent cowl 75mm dia complete all as specified and as directed. |
| 114 | Supply & Fixing in repair PVC (SWR) 110 mm dia branch piece, single (single Y) equal or unequal bore, complete all as specified and as directed. |
| 115 | Supply & Fixing in repair PVC (SWR) 75 mm dia branch piece, single (single Y) equal or unequal, complete all as specified and as directed. |
| 116 | Material & Labour in repair PVC (SWR) long arm floor trap / P trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed. |
| 117 | Supply & Fixing Stack clamps MS made out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stays to wall or roof for 100 mm bore pipe complete all as specified and as directed. |
| 118 | Supply & Fixing of MS angle iron bracket (design as directed) for door/windows chajja frame work with 04 nos MS fasteners of 16mm dia and 100mm long including MS rivets (for one set) drilling holes and making good fixed anchoring inside wall and top of roof complete all as specified and as directed (weight of fasteners including with MS angle frame arrengments). |
| 119 | Material & Labour for pre-cast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in cooking plateform, cover slabs for man-holes etc set in cement mortar (1:4) complete all as specified and as directed. |
| 120 | Material & Labour for Cement concrete type E-2 1:5:10 (using 40mm thick graded stone aggregates as in foundations, sunken portion filling and mass-concrete complete all as specified and as directed. |
| 121 | Supply & Fixing in repair Stainless steel curtain rod made out of 25 mm dia pipe having wall thickness 1.20 mm with two Stainless steel SS grade 304 brackets fixed with SS screws and PVC sleeves complete all as specified and as directed. |
| 122 | Dismentling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed. |
| 123 | Supply & Fixing Pre- painted galvalume aluminum zinc coating Iron based corrugated steel sheet 0.50mm thick, with side lap and end lap of any colour having tensile strength 550 Mpa ridges, hips, valley gutters, drips and straight flashing or in roof covering fixed with self tapping screws (length & girth as fixed) including taking down steel sheeting complete all as specified and as directed. |
| 124 | Supply & Fixing Pre- painted galvalume aluminum zinc coating Iron based plain steel sheet 0.50mm thick, with side lap and end lap of any colour having tensile strength 550 Mpa ridges, hips, valley gutters, drips and straight flashing or in roof covering fixed with self tapping screws (length & girth as fixed) including taking down steel sheeting complete all as specified and as directed. |
| 125 | Dismantling wall and ceiling boards (fiber, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and as directed. |
| 126 | Supply & Fixing in repair suspended false celing with \\"E\\" grid suspended ceiling grid system of grid size 600mmX600mm with GI frame work of main runner 38mmX24mm, sheet thickness .4mm, cross tee 28mmX24mm, sheet thickness .3mm and wall angle 24mmX24mmX.3mm including 4mm thick non asbestos fiber cement bldgs designer board conforming IS-14862 type B Cat 3 of oceanic texture and ivory colour of size 595mm X595 mm to be placed to centre in the grid suspended by 4mm dia GI wire at distance n.exc 1.2m centre to centre with butterfly clips complete all as specified and as directed. |
| 127 | Dismantling timber scantling 40 sq cm and over in section in any position all as specified and as directed. |
| 128 | Supply & Fixing Mild Steel Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe410-W (GdeE- 250) quality-A complete all as specified and as directed. |
| 129 | Material & Labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint including one coat of red oxide complete all as specified and as directed. |
| 130 | Material & Labour for one coat of synthtic enamel paint to old steel surfaces of any description exc. 10 cm girth or width including prepration old steel surfaces complete all as specified and as directed. |
| 131 | Material & Labour for rendering 10mm thick on fair face of brick works or concrete surfaces of walls with cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and asw directed. |
| 132 | Material & Labour for rendering 15mm thick on other than fair face of brick works or concrete surfaces of walls with cement mortar 1:4 finished surface even and smooth including liquid WPC @ 0.2% by weight of cement complete all as specified and as directed. |
| 133 | Material & Labour for rendering 10mm thick on concrete surfaces of ceiling with cement mortar (1:4) and finished even and smooth without using extra cement complete all as specified and as directed. |
| 134 | Material & Labour for applying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete as per manufacturer's specification on internal/ceiling surfaces including preparation of new plastered surface complete all as specified and as directed. |
| 135 | Material & Labour for coloured non skid ceramic tiles 7 to 8 mm thick joint less (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement to match with the shade of tiles over & including 15 mm thick screed bed in cement mortar 1:6, including dismantling of existing floor tiles including dismantling of old tiles complete all as specified and as directed. |
| 136 | Material & Labour for 15mm thick cement plaster in cement mortar 1:4 on fair faces of brick work finished even and fair complete all as specified and as directed. |
| 137 | Material & Labour for cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sunken floor for correction of slope etc complete all as specified and as directed. |
| 138 | Supply & Fixing Pressed steel frames 125mm x 60mm made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and as directed. |
| 139 | Supply & Fixing Pressed steel frames 105mm x 60mm made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and as directed. |
| 140 | Material & Labour PCC 1:2:4, type C0, using 12.50 mm graded aggregate as in filling in Pressed Steel Chowkhats complete all as specified and as directed. |
| 141 | Supply & Fixing 35 mm thick plain framed, panelled factory made shutters, 2nd class HW rail and style (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 142 | Supply & Fixing in repairs for Vitreous China wash down water closet pan semi-pedestal pattern (Anglo-Indian Type), white (including fixing bolts,flush pipe) front or back inlet including plastinc water closet seat cover closed pattern with flat bottom and connection to drain (or outgoing pipe) and to flushing pipe, etc and making good to floor complete as in repair all as specified and as directed. |
| 143 | Supply & Fixing in repair Vitreous china wash hand basin white flat back size 450 x 300mm including 32mm CP brass waste fitting, 45 cm long PVC connection with brass nut at both ends, 32mm dia PVC west pipe cast iron brackets and making good disturbed surfaces in CM 1:3 or PCC 1:2:4 complete all as specified and as directed. |
| 144 | Supply & Fixing in repair Pillar taps 15 mm Bore dia cast copper alloy with capstan heads cromium plated fancy type screwed down high pressure with or without lettered 'HOT' or COLD with long screwed for iron pipe and fixed in repair complete all as specified and as directed. |
| 145 | Material & Labour for wall mounted mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlets for hot & cold water, non telephonic shower arrangement, with connecting legs & wall flanges, inlets suitable for 15mm bore connections complete all as specified and as directed. |
| 146 | Supply & Fixing Angular Stop Cock with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron pipe or for union and fixed in position complete in all respect all as specified. |
| 147 | Supply & Fixing PVC connections 15 mm size with PTMT nuts of length 450 m complete all as specified. |
| 148 | Supply & Fixing GI tubes of medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors of 15 mm dia including taking down old pipe complete all as specified and as directed. |
| 149 | Supply & Fixing tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 20 mm dia including taking down old pipe complete all as specified and as directed. |
| 150 | PCC 1:3:6 type C-2 using 40mm graded stone aggretgate, as in base for PVC tanks, foundation filling and mass concrete etc complete all as specified and as directed. |
| 151 | Supply & Fixing repairs for 20 mm stop valve, cast iron , screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe of 20mm bore of pipe fixed as in repair complete all as specified and as directed. |
| 152 | Material & Labour Salt-glazed stoneware gully traps, Centrifugal type 150x150mm size, square or round mouthed, type 'P' or 'S' incl CI grating fixed in repair complete all as directed and as specified. |
| 153 | Supply & Fixing in repair cast iron floor trap spun type with CP grating including jointing to waste pipe in run lead dia of outlet 75mm including cutting floor and making good to match with existing surface fixed in repair complete all as specified and as directed. |
| 154 | Material & Labour cutting out cracks to V-section in existing roof slab or terrace, cleaning out, wetting, grouting, with cement sand slurry in 1:3 with mixing of WPC @ 2% by wt of cement complete all as specified and as directed. |
| 155 | Supply & Fixing 4 mm thick sheet glass ordinary quality and glazing with with beads / fixed with screws in square n.exc 0.5sqm in each pane complete all as specified and as directed. |
| 156 | Supply & Fixing in repair stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete including Supply & Fixing 02 Nos stainless steel brackets and finials fency type, stops fixed with ss screws etc all as specified & as directed.Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered. |
| 157 | Supply & Fixing factory made pre-laminated PVC solid board 18-20 mm thick prelaminated on both sides with wooden finished on one side and white finished lamination on other side as in cup-board front shutters complete fixed in position including taking down existing board any type complete all as specified and as directed. |
| 158 | Supply & Fixing solid WPC door frames of size 62 mm x 32 mm single rebate made out of solid WPC with standard Grade Density 780 Kg/CBM single side prelaminated PVC sheet and edges will be painted to match with prelaminated sheet as per specification and drawing. complete fixed in position in all respect complete all as specified and as directed. |
| 159 | Supply & Fixing auto closing hinges 35mm of O crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutter complete all as specified and as directed. |
| 160 | Supply & Fixing Stainless Steel (304 Grade) Finished Butt Hinges 150mm with stainless steel screws complete all as specified and as directed. |
| 161 | Supply & Fixing Stainless Steel (304 Grade) Finished Handles 150 mm with stainless steel screws complete all as specified and as directed. |
| 162 | Supply & Fixing Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long with stainless steel screws complete all as specified and as directed. |
| 163 | Supply & Fixing Hasp and staple 100 mm wide, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified. |
| 164 | Supply & Fixing Stainless Steel (304 Grade) Finished Floor Door Stooper with stainless steel screws complete all as specified and as directed. |
| 165 | Providng and injecting chemical emulsion for post construction anti termite treatment along the external wall below concrete or masonery apron using chemical emulsion @ 2.25 Ltr per liner meter inlcuding drillling and pluging holes etc in apron complete all as specified and as directed. |
| 166 | Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and as directed. |
| 167 | Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft loose soil complete all as specified and as directed. |
| 168 | Supply & Fixing Mild steel Angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. complete all as specified and as directed. |
| 169 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed. |
| 170 | Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and as directed. |
| 171 | Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm & n. exc 10 cm long complete all as specified and as directed. |
| 172 | Material & Labour Preparation of new surface appling two coat of synthetic enamel paint over one coat of red oxide primer n.exc 10 cm width or girth complete all as spcefied and as directed. |
| 173 | Material & Labour for preparing new plastered surfaces and applying Two coats of cement base paint over a coat of primer on surfaces of walls complete all as specified and as directed. |
| 174 | Dismantling posts or struts (wood, steel or R.C.C.) any section from concrete or brick masonary including taking out embedded portion and making good disturbed ground concrete, brick work,masonry complete all as specified and as directed. |
| 175 | Dismantling fencing along with wiremesh any type complete all as specified and as directed. |
| 176 | Dismantling of mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 177 | Excavating in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and as directed. |
| 178 | Material & Labour for PCC 1:4:8, type D-2 with using 40mm graded stone aggregated as in foundation filling complete all as specified and as directed. |
| 179 | Material & Labour Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. |
| 180 | Material & Labour Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m complete as specifiend and as directed. |
| 181 | Supply & Fixing Mild steel work as in framed and hung gates, including Pintle hinges, stops, hand made sliding bolts etc. and similar work confirming to Fe 410 - O or Fe 310 - O complete all as specified and as directed. |
| 182 | Material & Labour for hardcore of broken stone or boulders not exceeding 63mm, deposited, spread and leveled in layers not exceeding 15 cm thick waterd and rammed to a true surface etc complete all as specified and as directed. |
| 183 | Material & Labour for laying Sand filling under floors or in foundation/ path/interlock tiling including watering and consolidation not exc. 25cm thick below paver block complete all as specified and as directed. |
| 184 | Material & Labour for 75mm thick PCC 1:3:6 type C-2 using( 40 mm graded stone aggregate ) as in base of paving etc complete all as specified and as directed. |
| 185 | Material & Labour for PCC(1:2:4) type B-1 using 20mm graded stone aggregate as in Benching, rounded or chamfered on edges including necessary form work , if required etc complete all as specified and as directed. |
| 186 | Material & Labour 100 mm thick PCC 1:4:8, type D2 (using 40 mm crushed stone aggregate) as in sub base complete all as specified and as directed. |
| 187 | Material & Labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed. |
| 188 | Material & Labour pre cast plain cement concrete type C-I, 1:3:6 (using 20 mm graded stone aggregate) cast in situ in kerb stone set in cement motor 1:6 and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. |
| 189 | Supply & Fixing for 150 mm bore, Salt glased stoneware drain pipes (Grade 'A') laid in trenches at any depth including jointing and testing complete, including demolition of existing pipe complete all as specified and as directed. |
| 190 | Material & Labour PCC (1:4:8) type D2 using 40mm graded stone aggregate as in Concrete bed to drain pipes of 150mm bore including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and as directed. |
| 191 | Material & Labour for Plain cement concrete (1:2:4) type B-2 using 40 mm graded stone aggregates as surface channel/drains inside the manholes and like including weathering, sightly rounded or chamfered angles and throating as directed and provision of necessary formwork to any extent and finished exposed surface even and smooth without using extra cement complete all as specified and as directed. |
| 192 | Material & Labour brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radious, old size built in cement mortar 1:4 complete all as specified and as directed. |
| 193 | Material & Labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces walls, finished even & smooth without using extra cement complete all as specified and as directed. |
| 194 | Material & Labour for Cement concrete (1:2:4) type B-1 using 20mm graded machnically crushed stone agg as in benching, coping, plinth course, bands stops etc incl necessary form works complete all specified and as directed. |
| 195 | Material & Labour Cutting into existing MH for connecting new drains and making good to 150 mm dia. pipe and rendering cutting benching etc and finished etc complete all as specified and as directed. |
| 196 | Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 197 | INTERNAL ELECTRIFICATION (REPAIR) WORKS |
| 198 | Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and as directed. |
| 199 | Material & Labour for point wiring complete for one light/fan/ exhaust fan point controlled by one, one way 5 Amp switch with PVC (FRLSH) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including minimum 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including anodised pressed steel concealed terminal switch boxes not less than 1.20 mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLSH) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and as directed. |
| 200 | All as per item No 2.002 above but for call bell point complete all as specified and as directed. |
| 201 | All as per srl item No 2.002 above but for 5 pin 6 amps socket outlet independent board complete all as specified and as directed. |
| 202 | All as per srl item No 2.002 above but for 3 pin 6 amps socket outlet on the same board with other switch complete all as specified and as directed. |
| 203 | All as per srl item No 2.002 above but for one light point controlled by two Nos 2 way switches complete all as specified and as directed. |
| 204 | All as per Item No 2.002 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50 Sqmm and green colour earth cable of size 2.50 Sqmm, complete all as specified and as directed. |
| 205 | Material & Labour for point wiring complete with PVC (FRLSH) insulated unsheathed multistranded copper conductor of size 4 sqmm nominal cross sectional area single core drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, complete including 4 sqmm nominal cross sectional area PVC(FRLSH) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and as directed. |
| 206 | Supply & Fixing Single pole 20 amp, 230 volt and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB complete all as specified and as directed. |
| 207 | Supply & Fixing switch piano flush type one way 6 amps SP 230 volts complete all as specified and as directed. |
| 208 | Supply & Fixing switch piano 2- way, 6 amps flush type 230 volts complete all as specified and as directed. |
| 209 | Supply & Fixing bell push flush type 6 amps SP 230 volts complete all as specified and as directed. |
| 210 | Supply & Fixing piano flush type one way 16 amps SP 240 volts complete all as specified and as directed. |
| 211 | Supply & Fixing socket outlet 2 in 1, 3 pin 5/6 amps flush type 240 volts complete all as specified and as directed. |
| 212 | Supply & Fixing socket outlet 2 in 1, 6 pin, 5 and 16 amps flush type 230 volts complete all as specified and as directed. |
| 213 | Supply & Fixing bell ding dong AC, 230 VOLTS, single pole complete all as specified and directed. |
| 214 | Supply & Fixing ceiling rose of bakelite 65 x 50mm three terminals complete all as specified and as directed. |
| 215 | Supply & Fixing holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and as directed. |
| 216 | Supply & Fixing light fitting with energy saving decorative LED batten 20 watt (4 Feet), 230 voltas, energy efficient tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffusre & integrated electronic driver complete with all accessories prewired and includeing making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and as directed.Note:- Power factor should not be less thtn 0.95. |
| 217 | Supply & Fixing LED bulk head light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 218 | Supply and fixing light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 219 | Supply & Fixing LED building security light fitting 35/36 Watts, excellent thermally managed pressure die cast alumnium come with in-built photo sensor for automatic on/off, IP-66 including GI bracket made out of GI pipe 40 mm bore medium grade bent to an angle of 135 degree and reduced at the end to 32 mm dia, 1.20 mtr long including 2 Nos clamps, suitable size of nut bolts complete all as specified and as directed. |
| 220 | Taking down ceiling fan/Exhaust fan/geysers etc any type and size, sealing cable end, dismantling blades and removing fan and blades to deposite in E/M store yard complete all as specified and as directed. |
| 221 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. |
| 222 | Supply and fixing exhaust fan, steel bodyAC single Phase. 230V of size 300msweep with, blades, and frame and louvers complete all as specified and as directed. |
| 223 | Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed. |
| 224 | Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc.”complete all as specified and as directed. |
| 225 | Supply & Fixing in repair sheet metal enclosure VTPN duble door with suitable size of bus bar TPN 8 way as per IEC-61439-3, with neutral bar, earth bar and cable ties for cable management complete all as specified and directed and also including disconnecting the electric connection from electric meter (incoming and outgoing ) for repair work and making fresh proper electric connection incoming and outgoing using proper size of lugs and wire as required as specified and as directed. |
| 226 | Supply & Fixing MCCB 3 Pole, 415 V, fixed type, 63 Amps with breaking capacity 16 KA complete all as specified and as directed. |
| 227 | Supply & Fixing in replacement of sheet metal enclosure distribution box suitable for MCB'S 8 way SPN 240 volts with 200 Amps rated bus bar double door complete including connecting up and making good distrubed surface complete all as specified and as directed. |
| 228 | Supply and fixing MCB SPN 40 to 63 AMP amp rating 240V, 10KA ‘B ’ curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. |
| 229 | Supply and fixing MCB SP 6 to 32 AMP amp rating 240V, 10KA ‘B ’ curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. |
| 230 | Supply and fixing MCB SP 40 AMP amp rating 240V, 10KA ‘B ’ curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. |
| 231 | Supply & Fixing in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6 sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and as directed. and also include Dismantling of existing service wire of any type / make upto 25 sqmm 4 core. |
| 232 | Excavation in trenches in soft/loose soil n.exc 1.5m wide and above 1.5m depth for laying or errection of poles, stay etc and laying of pipe line, cables etc, and getting out complete all as specified and as directed. |
| 233 | Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in any type of soil complete all as specified and as directed. |
| 234 | Removing surplus excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed. |
| 235 | Supply and laying in replacement, double walled corrugated (DWC) HDPE duct pipe conforming to IS 16205 Pt -24 of approved color complete with fittings for cable protection of size 63 mm outer dia and 50 mm inner dia complete all as specified and as directed. |
| 236 | Material and labour for PCC (1:3:6) type C1 (using 20mm graded aggregate) in coping/pedestal of poles including necessary form work and finishing surfaces fair and even using extra cement complete all as specified and as directed. |
| 237 | S&L XLPE LT UG cable PVC insulated, bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of of cable 35 Sqmm 3.5 Core, including taking down the existing unserviceable UG cable complete all as spd and as directed. |
| 238 | Material & Labour for removal of existing old unsv earthing complete and providing new earthing with galvanised steel earth plate electrode, 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, GI tubing 15 mm bore medium grade protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal, salt complete all as per SSR with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way including earth work in any type of soil , removal of surplus soil to a distance n.exc 50 m and connecting, testing on completion all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and as directed. (Note: Excavation and earth work is deemed to be included in the rates quoted of this item). |
| 239 | Deduct Schedule of Credit of Rs. 15,99,824.00 as brought out from Sr Page No. 68 of tender SCHEDULE OF CREDIT NOTES:1. The materials listed below retrieved from demolition/dismantling as specified in Schedule of credit shall become the property of the contractor and the credit amount as indicated below shall be recovered from the RAR as the work proceeds. Demolition of the work shall be carried out after it is handed over for demolition all as directed by the Engineer-in-Charge. Any other retrieved item not listed below shall become Govt. property.2. The unit rate of salvage materials which will become the property of contractor as assessed by the department is indicated in the schedule of credit and it is final and binding. The contractor is deemed to have visited the site and made his own assessment regarding condition of the materials. No claim of the contractor. Whatsoever against the department regarding actual cost of salvage material is admissible.3. The contractor shall be responsible to remove the materials obtained from demolition from the site as directed and the site shall be left clean and tidy and same shall be deemed to be included in the rates quoted for demolition.4. The contractor shall be allowed to remove the salvage materials from the site only after written approval of the GE after necessary recovery has been made in the RAR. However, in case of any dispute regarding demolished item, decision of CWE shall be final and binding upon both the parties.5. The quantities mentioned under column 4 are approximate and are given as rough guide only. The quantities obtained from items of Schedule 'A' shall be considered for credit. The tenderer shall not have any claim whatsoever for any variation of quantities given in Schedule of credit. Srl No Description of items of works Unit No of Units Rate in Rs Amount in Rs |
| 240 | Old unserviceable Brick work obtained from demolition. |
| 241 | Old unserviceable GI Tubing 15mm bore. |
| 242 | Old unserviceable GI Tubing 20mm bore. |
| 243 | Old unserviceable CP stop cock/Bib tap/pillar tap/angle cock of any size and description. |
| 244 | Old unserviceable Brass gate valve / Stop Vlave of 20mm bore. |
| 245 | Old unserviceable looking mirror of any description. |
| 246 | Old unserviceable Flushing cistern of any description. |
| 247 | Old unserviceable sink of any description. |
| 248 | Old unserviceable EWC/IWC of any description. |
| 249 | Old unserviceable WHB of any description. |
| 250 | Old unserviceable PVC connection. |
| 251 | Old unserviceable CP shower rose with shower arm of any description. |
| 252 | Old unserviceable Towel rail of any description. |
| 253 | Old PTMT/CP Grating of any description. |
| 254 | Old unserviceable CP Wall/sink Mixture. |
| 255 | Old unserviceable Soap dish. |
| 256 | Old unserviceable Towel ring. |
| 257 | Old unserviceable PVC water tank of any description 500Ltr capacity. |
| 258 | Old wooden / iron chowkats with wooden shutter exc 1.5 Sqm and n. exc 4.00Sqm each including all fittings complete. |
| 259 | Old wooden / iron chowkats with wooden shutter n.exc 1.5 Sqm each including all fittings complete. |
| 260 | Iron unserviceable iron scrap. |
| 261 | Old unserviceable PVC / AC waste water pipe of any description. |
| 262 | Old unserviceable CI / PVC Pipes of 100mm bore. |
| 263 | Old unserviceable CI Pipes of 75mm bore. |
| 264 | Old unserviceable CI bend/CI branch pieces 100mm bore of any description. |
| 265 | Old unserviceable wirecloth. |
| 266 | Old unserviceable CI Floor trap/CI bend/CI branch pieces 75mm bore of any description. |
| 267 | Old unserviceable Aluminium handle of any type. |
| 268 | Old unserviceable PVC water tank of any description 1000Ltr capacity. |
| 269 | Old unserviceable AC Sheet. |
| 270 | Old unserviceable Curtain rod. |
| 271 | Old unserviceable False ceiling. |
| 272 | Old unserviceable wooden scantling. |
| 273 | Old unserviceable chain link fencing. |
| 274 | Old unserviceable kota stone / sand stone/ granite stone slab/ paver block/ concrete tiles/ dholpur stone etc retrieved from demolition of flooring. |
| 275 | Old unserviceable Brick tiles retrieved from demolition. |
| 276 | Old unserviceable particle board retrieved from demolition. |
| 277 | Old unserviceable Point wiring complete with conduit /batten etc including old metreials. |
| 278 | Old unserviceable material such as switchs, socket, ceilling rose, lamp holders, bells, regulators etc . |
| 279 | Old unserviceable brunt SPN DB 4/8/12 Way. |
| 280 | Old unserviceable Light fitting any type. |
| 281 | Old unserviceable sub main wiring /serive connection of any type. |
| 282 | Old unserviceable Security light. |
| 283 | Old unserviceable Earthing. Total amount of Credit Schedule 1599824.0 Signature of Contractor AAD (Contracts)For Accepting Officer Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 33 daysJan 01, 2027
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 40 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender