Tender For Special Repair Of 03 X Toilets In Bldg No P-259 Sm Barrack Under Ge (West) Mathura
Tender Value
25.24 Lakhs
Estimated cost
Bid Submission
11 Dec 2026
19 days left
EMD
50499
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mathura → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair Of 03 X Toilets In Bldg No P-259 Sm Barrack Under Ge (West) Mathura
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 2 | Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. |
| 3 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and directed. |
| 5 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-charge. |
| 6 | Taking down chowkhats with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each complete all as specified and directed. |
| 7 | Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4.00 sqm each complete all as specified and directed. |
| 8 | Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge. |
| 9 | Dismantling brick/concrete tiles any size etc including existing roof treatment of any thickness complete all as specified and directed. |
| 10 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thick above or below ground level complete all as specified and directed. |
| 11 | M&L for cement concrete (1:2:4) type B2 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railigs upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, sligtly rounded or chamfered angles and throating, as directed including necessary form work complete all as specified and directed. |
| 12 | M&L for reinforced cement concrete (nominal mix) (1:2:4) type B1, using 20mm graded stone aggregate for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and other similar works complete all as specified and directed and directed. |
| 13 | M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge. |
| 14 | All as per Srl item No 13.00 here-in-before but except brick.Note : Old serviceable brick retrieved from serial item No 2.00 of BOQ here-in-before shall be used under this item. |
| 15 | M&L for brick work with sub class ‘B’ old size burnt bricks straight or curved on plan to any radius half brick thick wall built in CM (1: 6) complete all as specified and directed. |
| 16 | M&L for applying a coat of two component elastomeric acrylic polymer modified cementitious water proofing coating, having properties of 80 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturers specifications and sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed. |
| 17 | S&F Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed. |
| 18 | M&L for cement concrete type C-1, (1:3:6) using 20mm graded aggregate as in bed block or filling of chowkhats including necessary form work complete all as specified and directed. |
| 19 | M&L 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.24 (a) complete all as specified and directed. |
| 20 | S&F 35mm thick plain framed panelled door shutter, factory made (any number of panels) of 2nd class hard wood with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces including 2nd class hard wood kail beading 20mm wide tapering from 10mm to 5 mm on one side of shutter & fitted to chowkhats. The size of rail and style shall be as per IS –1003 (Part-I) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and directed. |
| 21 | S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge. |
| 22 | S&F Factory made box type steel windows with hung shutters both glazed and guaged shutter frame 60x25 mm ERW hollow 'P' section with wall thickness not less than 1mm fixed to pressed steel frame 120mm x 70 mm x 1.6mm thick including fixing glazed portion, iron grills 8mm square MS bar hunges with steel handle and fitting, lugs etc, including one shop coat of primer complete all as specified and directed. |
| 23 | S&F Factory made box type steel windows with hung shutters both glazed shutter frame 60x25 mm ERW hollow 'P' section with wall thickness not less than 1mm fixed to pressed steel frame 120mm x 70 mm x 1.6mm thick including fixing glazed portion, iron grills 8mm square MS bar hunges with steel handle and fitting, lugs etc, including one shop coat of primer complete all as specified and directed. |
| 24 | S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified and directed by Engineer-in-charge. |
| 25 | Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge. |
| 26 | S&F 4 mm thick sheet glass,ordinary quality and glazing with oil putty in squares not exceeding 0.50 sq.m. in each shape complete all as specified and directed. |
| 27 | S&F 4mm thick figured glass in glazing to aluminium door, window & partition including pad panes complete all as specified and directed by Engineer-in-Charge. |
| 28 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. |
| 29 | S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. |
| 30 | S&F Aluminium handle cast type anodized 100mm long complete all as specified and directed by Eng-in-charge. |
| 31 | S&F Aluminium handle cast type anodized 150mm long complete all as specified and directed by Eng-in-charge. |
| 32 | S&F 300mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) complete all as specified & directed by Engineer-in-Charge. |
| 33 | S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed. |
| 34 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge. Note: Stainless steel butt hinges and necessary SS screws shall be paid separately. |
| 36 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 X 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note :(i) MS hold fast/ lugs or SS dash fasteners shall be paid for separately). (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 37 | M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate ) as in floor finishes and leveling course complete all as specified and directed. |
| 38 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm screed bedding in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. |
| 39 | M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge. |
| 40 | M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed. |
| 41 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge. |
| 42 | All as per item No 41.00 (here-in-before) above but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed. |
| 43 | M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge.Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item complete all as spcified and directed. |
| 44 | M&L for rendering 15 mm thick in CM 1:4 including water proofing compound on fair face of brick or concrete surface, finished even and smooth without using extra cement complete all as specified and directed. |
| 45 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed. |
| 46 | M&L for rendering 5mm thick in CM (1:3) as on ceiling complete all as specified and directed. |
| 47 | Supply only liquid water proofing compound ISI marked complete all as specified and directed by Engineer-in-charge |
| 48 | M&L preparation of new plastered surfaces of wall and distempering with two coat of 1st quality acrylic distemper (ready mixed) having having VOC less than 50gm/litre of approved manufacturer of required shade and colour complete as per manfacturer's specification over a coat of 1mm thick wall care putty complete all as specified and directed. |
| 49 | M&L for complete removal of existing treatment and preparation of old treated surfaces of wall for applying two coats of distempering with 1st quality acrylic distmper (ready mixed) having VOC content less than 50gm/litre of approved manufacturer, of required shade and colour over a coat of wall care putty complete as per manufacturer specification complete all as specified and directed. |
| 50 | M&L for preparation of old treated surfaces of wall for applying two coats of distempering with 1st quality acrylic distmper (ready mixed) having VOC content less than 50gm/litre of approved manufacturer, of required shade and colour complete as per manufacturer specification complete all as specified and directed. |
| 51 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 52 | M&L for complete removal of existing treatment and preparation of old surfaces of ceiling and applying three coats of white wash complete all as specified and as directed. |
| 53 | M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 54 | M&L for washed stone grit plaster on exterior walls in two layers the base plaster shall be 15mm thick in two layers. First layer 10mm thick in CM (1:6) & top layer 5mm thick in CM (1:4) mixed with approved water proofing compound @ 3% & shall be sufficiently rough and combed be wire brush or nail comb, feed from all dust, dirt, grease, oil etc for proper bonding. The base plaster shall be cured for 3 to 4 days before applying the grit wash plaster. A homogeneous mix of white cement, coarse sand and 10mm nominal size sone chippings of approved colour in proportion 1:1/2:2 be prepared by adding water proofing compound @ 2% by weight of cement and be mixed homogenously and then mix be applied |
| 55 | Cont/-on a prepared base surface with a float applying gentle pressure in panels with groove all around as per approved pattern including beading, White cement slurry shall be applied @ 2Kg/sqm on base coat before applying a stone grit wash plaster. After the initial setting of about 1 to 2 hours the surface of stone grit plaster surface be scrubbed and washed out gently with a nylon brush and water. The cement on the surface of stone chips be washed away exposing the aggregates and plastered surface shall be cured for 14 days including necessary steel scaffolding work, complete all as specified and directed. |
| 56 | Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 57 | Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 58 | S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge |
| 59 | S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge |
| 60 | S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge. |
| 61 | S&F in repairs vitreous china wash down, water closet pan (pedestal pattern), white including fixing bolts and connection to flush pipe and drain out going pipe and closet seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, CP jet including PVC connection complete all as specified and directed. |
| 62 | S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 1000 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed. |
| 63 | S&F 20mm dia ball brass valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engineer-in-charge. |
| 64 | S&F in repair CP Health faucet with stand fixed on wall in CP hose pipe 1 mtr length and stainless steel screw as approve complete all as specified and directed by Eng-in-charge. |
| 65 | S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge. |
| 66 | S&F in repair brass chromium plated towel ring round with round flange fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge. |
| 67 | S&F in repairs chromium plated Soap dish holder including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge. |
| 68 | S&F in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge. |
| 69 | S&F in repair 600mm x 450mm beveled edge looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick commercial plywood including PVC moulded framing and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-charge. |
| 70 | S&F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed. |
| 71 | S&F 100mm CI pipes soil, waste and vent pipe in any length with or without ears, with cement joints fixed to wall including taking down old unserviceable CI pipe and fittings complete all as specified and directed. |
| 72 | S&F 75mm CI pipes soil, waste and vent pipe in any length with or without ears, with cement joints fixed to wall including taking down old unserviceable CI pipe and fittings complete all as specified and directed. |
| 73 | S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed. |
| 74 | S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-charge. |
| 75 | S&F 100mm bore cast iron bends (any radius), with duck's foot or heel rest complete all as specified and as directed. |
| 76 | S&F 75mm bore cast iron bends (any radius), with duck's foot or heel rest complete all as specified and as directed. |
| 77 | S&F 100mm bore dia cast branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed. |
| 78 | S&F 75mm bore dia cast branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed. |
| 79 | S&F GI spout pipe 50 mm dia tubes,light grade galvanised, with all fitting, laid in treanches complete all as specified and as directed. |
| 80 | S&F 75-80mm thick factory made precast RCC manhole covers including precast frame of any size & shape (Squre / rectangular / circuler), light duty, out side, fixed at site etc complete all as specified and directed.Note : Reinforcment required shall be included in quoted item rate. |
| 81 | M&L for TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 82 | M&L SGSW gully traps square or round mouthed type P of size 180 x 150mm complete all as specified and directed. |
| 83 | S&F in repairs PVC waste pipe 32mm dia of length 0.8mm to 0.9mm fixed complete all as specified and directed. |
| 84 | M&L for water proofing treatment with APP modified bituminous membrane 3mm thick consisting of the following for RCC roof :-(a) Cleaning palstered roof surfaces and applying a coat of oxidised bitumen based solvented primer a@ 0.3Kg /Sqm of approved make on top of dry surface of RCC roof complete all as specified and directed.(b) M&L for APP modified polymeric water proofing membrance 3mm thick weight not less than 3.0 Kg/Sqm with non woven polyster core of approved make applied by heating one surface of membrane with LPG torch with lap of 100mm and the overlap shall be sealed by flame complete all as specified and directed. |
| 85 | S&F repairs PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed. |
| 86 | S&F repairs PVC (SWR) multi floor trap 75mm dia outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed. |
| 87 | M&L for cutting chases, pining in, making good to facing where required and pointed in CM (1:3) for concealed steel water tubing & like and making good, match with existing surfaces by applying white wash/colour wash cutting not exc 10cm girth complete all as specified and directed. |
| 88 | S&F in repair 15mm dia stop cock cast copper alloy, fancy type with, chromium plated long shank and cup (concealed type) with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge. |
| 89 | S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. |
| 90 | S&F in replacement PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed. |
| 91 | S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed. |
| 92 | S&F pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 93 | S&F in repairs vitreous china urinal Half stall type, white incl CP spreader screwed for iron pipe and fixed complete including providing and fixing plugs with and including 60mm long brass screws, pointed around urinal back in cement, fixing discharge pipr, flush pipe, grating and union for discharge complete all as specified and directed by Eng-in-charge. |
| 94 | S&F in repair 20mm gun metal globe or gate valve conforming to IS : 778 ISI marked with iron wheel head screwed both ends for iron pipe including GI fitting socket, nipple, unions as well cutting of pipe and necessary earth work complete all as specified and directed. |
| 95 | Extra over cast iron 75mm dia pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and directed. |
| 96 | Extra over cast iron 100mm dia pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and directed. |
| 97 | Blank |
| 98 | M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge. |
| 99 | M&L for preparation of old steel surfaces of any description or girth over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 100 | M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 101 | M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 102 | S&F precast hydraulically pressed PCC tiles of size 30cm x 30cm x 20mm thick laid over and including screed bed 15mm thick in CM (1:4) set and jointed in neat cement slurry and pointed in CM (1:3) mixed with WPC of approved make in screed bed and pointing on roof complete all as specified and directed. |
| 103 | M&L for treatment of sunken floor slab comprising of the following specifications with and including demolition of sunken floors complete all as specified and directed:-(i) Cleaning the sunken/lowered portion of \ RCC slab surface (incl vertical total depth plus skirting height) of floors by wire brush,chisel out any mortar sticking to the surface and brooming completely. Provn of 40 mm thick avg PCC 1:2:4 type B-O using 12.5mm graded aggregate as in padding concrete to achieve proper slope incl cutting holes in bricks or RCC wall for sprout.(ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and incl integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thermax as approved by GE @ 0.2% by wt of cement consumed incl filling it with water to check dampness and seepage and where dampness/seepage is noticed, nozzles shall be fixed and grouting carried out.Cont/- |
| 104 | Cont/-(iii) All junctions points of side wall where CI/GI/PVC pipes are passing through shall besealed with epoxy puttySikaguard 694 F(I) or equivalent make in Fosroc/Thermax as approved by GE(iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean(v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or equivalent make in Fosroc/Thremax as approved by GE over base coat as per manufacturer's instruction to bottom and vertical sides upto finished floor level +100 mm height. The thickness of two layers shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vetical and bottom surface of the sunken portion.Cont/- |
| 105 | Cont/-(vi) Plaster the bottom surface and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with and incl integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc/Thermax as approved by GE @ 0.2% by wt of cement consumed as per manufacturer's specification incl rounding of corners and injuctions sloping towards spout.(vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint. |
| 106 | Supply and fixing of Tollet Water Supply Pipe 3/4\\" (20 mm)-2 nos. downtake pipes fixing done with Pipe Supporting Clamping System having Profile Bracket+ Slotted C Channel + U Bolt R/M System -1. Domestic Water Supply Down take lines 3/4\\" GI-2 nos. from Terrace to 1st & Ground Floor Vertical Fixed line with wall distance 4\\": Pipe Support Clamping made of: 1. Profile Bracket Wall Distance 4\\" made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method-ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 13 with Serration as per DIN 6923.Cont/- |
| 107 | Cont/- 2. Slotted \\"C\\" Channel B3 Type to be used of size 10\\" (Continuous Slotted \\"C\\" Channel with ribs) made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material 48mm x 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx, Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923-Zn Al Flake coated. Hotdip Galvanizing as per IS 2629 (1985)-610 grams/m2 (>85 microns). Material Grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Cont/- |
| 108 | Cont/- Material Qty: 1. Profile Bracket Wall distance 4\\"-2 Nos. 2. Continuous Slotted C Channel of B3 Type Size 10\\" - 1 No. 3. U Bolt R/M for 3/4\\" GI pipe Dia. - 2 Nos. 4. Justi Khilla GI coated 2 1/2\\"-4 Nos. Fixing details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02.Make: Shaivi or equivalent as approved by GE. |
| 109 | Supply and fixing for Pipe Supporting Clamping - Single Pipe of dia 20 mm (3/4\\") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 75 mm (3\\"): Pipe Support Clamping made of: 1. Mono Bracket for 20 mm (3/4\\") pipe having Wall Distance 75 mm (3\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs.2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Cont/- |
| 110 | Cont/-Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 20 mm (3/4\\") pipe, Wall distance 75 mm (3\\") - 1 Nos. 2. U Bol Rubber Sleeve mounted for 20 mm (3/4\\") GI / UPVC/ CPVC pipe Dia. - 1 nos 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2\\") - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02. Make : Shaivi or equivalent as approved by GE. |
| 111 | Supply and fixing for Pipe Supporting Clamping - Single Pipe of dia 15 mm (1/2\\") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 75 mm (3\\"): Pipe Support Clamping made of:1. Mono Bracket for 15 mm (1/2\\") pipe having Wall Distance 75 mm (3\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs..2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Cont/- |
| 112 | Cont/-Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 15 mm (1/2\\") pipe, Wall distance 75 mm (3\\") - 1 Nos. 2. U Bolt Rubber Sleeve mounted of 15 mm (1/2\\") Pipe Dia. - 1 nos and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2\\") - 2 Nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02. Make : Shaivi or equivalent as approved by GE. |
| 113 | Supply and fixing for Pipe Supporting Clamping - Water supply pipes - 3 no. of dia 20 mm CPVC / GI pipeline running on terrace floor fixing done with Pipe Support Clamping System consists of Terrace Floor Clamp + U Bolt Rubber Sleeve mounted system running horizontally above floor level 100 mm (4\\"): Pipe Support Clamping made of: 1. Terrace Floor Clamp - 15\\" Width x 4\\" Height made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. Rubber pad made Nitrile Butadiende Rubber (NBR); Dimension : Base - 54 mm x 54 mm; tapered above to 44 mm x 44 mm and height - 25 mm; inserted with SS304 Hex Flange nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. The clamp and rubber pad are combined together using SS304 Hex Flange Bolt with serration 5/16 x 3/4 (A/F 13 mm) as per DIN 6921.Cont/- |
| 114 | Cont/-2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Terrace Floor Clamp - 15\\" Width x 4\\" Height - 1 Nos. 2. U Bolt Rubber Sleeve mounted for 25 mm (1\\") CPVC pipe Dia. - 4 nos.Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02. Make : Shaivi or equivalent as approved by GE |
| 115 | Supply and fixing for Pipe Supporting Clamping - Water supply pipes - 3 no. of dia 25 mm CPVC / GI pipeline running on terrace floor fixing done with Pipe Support Clamping System consists of Terrace Floor Clamp + U Bolt Rubber Sleeve mounted system running horizontally above floor level 100 mm (4\\"): Pipe Support Clamping made of: 1. Terrace Floor Clamp - 15\\" Width x 4\\" Height made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. Rubber pad made Nitrile Butadiende Rubber (NBR); Dimension : Base - 54 mm x 54 mm; tapered above to 44 mm x 44 mm and height - 25 mm; inserted with SS304 Hex Flange nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. The clamp and rubber pad are combined together using SS304 Hex Flange Bolt with serration 5/16 x 3/4 (A/F 13 mm) as per DIN 6921.Cont/- |
| 116 | Cont/-2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated.Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Terrace Floor Clamp - 15\\" Width x 4\\" Height - 1 Nos. 2. U Bolt Rubber Sleeve mounted for 25 mm (1\\") CPVC pipe Dia. - 4 nos.Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jaipur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : TD/2022/01 and TD/2024/02. Make : Shaivi or equivalent as approved by GE |
| 117 | Taking down surface / concealed copper / aluminium point wiring (light, bell, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, lamp holders, pendants, sockets, regulators, tubelight fittings etc and making good disturbed surfaces with plaster on walls, floors etc complete all as specified and directed. |
| 118 | M&L for Point wiring complete with 1.5 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with modular sheet cover for fixing switches, sockets, regulators etc. alongwith 1.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed. |
| 119 | All as per serial item No. 109.00 here-in-before but for One 3 pin 5 Amp socket outlet on independent board. |
| 120 | All as per serial item No. 109.00 here-in-before but for One 5 pin 5 Amp socket outlet on the same board with other switches. |
| 121 | M&L for point wiring with 2.5 sqmm PVC insulated, unsheathed FRLSH multistrand copper conductor cable 1100 volts grade drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all and including conduit fittings and fixing accessories 1.2mm thick sunken anodised pressed steel terminal boxes with 3.0 mm thick hylam sheet cover for mounting switches, socket etc including 2.5 Sqmm FRLSH multistrand copper conductor cable as continuous earth wire complete for one socket 16 Amp socket outlet controlled by one switch on independent board.complete all as specified and directed. |
| 122 | M & L concealed sub main wiring with 2 runs of 4 sqmm main wire along with 1 run of 4 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the same including taking down old unserviceable cable complete all as specified by Engr- in- Charge.NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. |
| 123 | M & L concealed sub main wiring with 2 runs of 6 sqmm main wire along with 1 run of 6 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the same including taking down old unserviceable cable complete all as specified by Engr- in- Charge.NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. |
| 124 | S & F modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed. |
| 125 | S & F modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. |
| 126 | S & F modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. |
| 127 | S & F modular type 2/3 pin 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. |
| 128 | S & F modular type 3/5 pin socket with one single pole MCB 20 Amps 230 volts complete all as specified including concealing in wall suitable for AC and domestic appliances complete all as specified and directed. |
| 129 | S&F ceiling rose 63x30 mm three terminal, polycorbonate body complete all as specified and directed. |
| 130 | S&F in repairs Angle / batten holder polycorbonate type body suitable for batten fitting complete all as specified and directed. |
| 131 | S&F in repairs LED bulb base B22 of capacity 10 watts not less than 700 lumens output at 6500K colour temp, complete all as specified and directed. |
| 132 | S&F in replacement LED (1.2m) smartbrite extra batten made of CRCA sheet housing provided for efficient heat dissipation with a PC glossy diffuser duly prewired connection having a normal system lumen output of 2000 lumen/20 watt at a minimum system efficacy of 2000 lumen per 20 watt and total power consumption not more than 20 watt including driver of capacity 10 KA. It has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10\\"%\\" AND PF>0.95 complete all as specified and directed. |
| 133 | S&F in replacement LED (0.6m) smartbrite extra batten made of CRCA sheet housing provided for efficient heat dissipation with a PC glossy diffuser duly prewired connection having a normal system lumen output of 1150 lumen/10 watt at a minimum system efficacy of 1150 lumen per 10 watt and total power consumption not more than 10 watt including driver of capacity 5 KA. It has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10\\"%\\" AND PF>0.95 complete all as specified and directed. |
| 134 | S&F in repair Security Light of 35 watts of new generation energy saving & environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and impact resistance of IK07 with 10KV Built -in-Surge Protection Devision,should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 including suitable pipe, clamps, nut and bolts for mounting the light all as specified and directed. |
| 135 | Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. |
| 136 | Supply & fixing in replacement MCB Single Pole Neutral 240 volt any rating from 40 to 63 amps, C series with rupturing capacity 10 KA complete all as specified and directed. |
| 137 | Supply & fixing in replacement of MCB single pole 240 volt any rating from 6 to 32 amps, B series with rupturing capacity 10 KA complete all as specified and directed. |
| 138 | S & F in replacement of worn out MCB DB TPN with sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door with isolated Neutral Bar & Shrouded bus bar IP protection 43 having door earthing complete all as specified and directed. |
| 139 | S&F in repairs MCCB, 160 Amp, 4 Pole, 36 KA, 415 volts adjustable thermal & fixed magnetic setting complete all as specified and as directed. |
| 140 | Supply, installation and commissioning in replacement (maximum energy efficient type) water heater storage type, five star electric complete of capacity 25 litres, heating element capacity 2 KW, vertical, plastic body including grouting of studs in wall in cement mortar (1:3) nuts, washers and provision of two numbers heavy duty flexible SS connection pipe of hot and cold of 600 mm long with brass nuts and two number brass chromium plated angular valve suitable for 15 mm bore pipe for water supply connection complete all as specified and directed.Note : Old unserviceable water heater shall be deposited in AGE E/M store yard. |
| 141 | Supply and fixing in replacement exhaust fans 300 mm sweep metallic body, heavy duty, four blade, double ball bearing, 1400 RPM, minimum air delivery discharge 1710 CMH suitable for SP, 230/250V, 50 Hz AC supply with protective bird guard with louver shutters including grouting of frame in wall and connecting with and including 3 run 1.5 Sq mm single core, PVC insulated but unsheathered FRLSH multistranded copper conductors cable from ceiling rose to exhaust fan complete all as specified and directed.Note : Old unserviceable exhaust fan shall be deposited in AGE E/M store yard. |
| 142 | M&L for taking down exhaust fan for greasing, painting and servicing and refixing the same as original complete all as specified and directed. |
| 143 | M&L for in replacement earthing with galvanised steel earth plate elctrode 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr below GL) with the toop edge of the plate not less than 1.5 mtr below the normal group level connected to GI earth srtip of size 25x4mm thick soldered and riveted to earth plate,GI earth strip will be protected by using 50mm bore GI pipe (light grade) earth plate to equipment and watering pipe 20mm bore (light grade) and chamber/pit in PCC(1:3:6) type C1 using 20mm graded stone aggregate with precast RCC pit cover 50mm thick in (1:2:4) type B1using 20mm graded stone aggregate reinforced with 8mm dia MS TMT bar at 80mm c/c both way with lifting hook made out of 8mm dia TMT bar duly embedded in RCC cover in lieu of CI pit cover with angle iron frame including excavation and earth work and removal of surplus soil complete all as shown in electrical plase No.3 of SSR Part-I and as specified including earth plate surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers of charcoal dust, common salt complete and earth lead connected to earthing test point/main board all as specified and testing of earthing complete all as specified & directed. |
| 144 | Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.50 mtr depth for foundation etc or for shafts, wells, cesspits, main holes, pier holes etc complete in soft/loose soil complete all as specified and directed. |
| 145 | Returning, filling including spreading, levelling, watering and well ramming in layers n.exc. 25 cm thick in soft/loose soil complete all as specified and directed. |
| 146 | Removing excavated materials not exc 50 mtr and deposited where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and as directed. |
| 147 | M&L for sand cushioning and covering clean and dry sand to underground electric cable with 8 cm before laying and 10 cm over the cable including ramming complete all as specified and directed.Note :- Punned thickness shall be measured and paid for. |
| 148 | M&L for sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed. Please Enable Macros to View BoQ information |
| 149 | M&L for sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysDec 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender