Tender For Provn Of Pathway For Certain Roads At Lichubari Under Ge Jorhat.
Tender Value
38.83 Lakhs
Estimated cost
Bid Submission
11 Dec 2026
19 days left
EMD
78000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jorhat → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Pathway For Certain Roads At Lichubari Under Ge Jorhat.
BOQ
| Sl. No. | Item Description |
| 1 | NOTE:-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.(ii) It is highlighted that the certain condition of General Condition of Contracts (IAFW-2249) has been modified as per direction of MoD i.e. inclusssion of Performance Security, deletion of Risk & Cost Provisions and increase in defect liability period all as per tender documents. The tenderers should keep in mind while quoting their offer. (iii) (Applicable for all items/parts):- The bidders/contractors are advised to refer Notes on BOQ/SCH'A' before entry/quoting the rates. |
| 2 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed. |
| 3 | Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundations or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10Sqm on plan and not exceeding 1.50m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm on soft/loose soil complete all as specified and as directed. |
| 5 | Removing excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed. |
| 6 | Material and labour for hardcore of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 7 | Material and labour for providing cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 8 | Material and labour for providing cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 9 | Material and labour for providing cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concreting complete all as specified and as directed. |
| 10 | Material and labour for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in surface channel, drains and like etc. complete all as specified and as directed. |
| 11 | Material and labour for plain cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in roof kerb or mud stops, rounded or chamfered on edges complete all as specified and as directed. |
| 12 | Material and labour for PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary use and waste of formwork complete all as specified and as directed. |
| 13 | Material and labour for providing precast cement concrete (1:2:4), type B-1, (using 20mm graded aggregate) as in landings, cover slabs(for manholes, etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:4) including necessary use and waste of form work complete all as specified and directed.Note: Reinforcement shall be measured and paid seperately under respective item. |
| 14 | Material and labour for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base floring and finish the surface fair and even complete all as specified and as directed. |
| 15 | Material and labour for 25mm thick precast cement concrete louvres and jallies (measured solid) (1:2:4) type B0 (using 12.5mm graded stone aggregate) including all mouldings and set in CM (1:4), excluding frame complete all as specified and as directed. |
| 16 | Material and labour required extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed. |
| 17 | .-Ditto- all as per item No 15.00 above but add or deduct for each 25mm girth or part there of over or under 30cm and -ditto-. |
| 18 | Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:4) complete all as specified and as directed. |
| 19 | Materials and labour for half brick thick brick work with old size sub class 'B' bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and as directed. |
| 20 | Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. |
| 21 | Supply and fixing steel work in tubular trusses i.e truss bottom, top bend, sides, side supports, holding plates, posts and base plate etc. including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 etc complete all as specified and as directed. |
| 22 | Material and labour for non skid ceramic coloured tiles (Premium Quality) 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 23 | Material and labour for glazed ceramic coloured tiles (Premium Quality) of size 600 x 300 x 8mm thick as on vertical surfaces, set and jointed in neat cement slurry and pointed in white cement with pigment to match with the shade of tiles laid over and including 10mm thick cement plaster in CM (1:4) complete all as specified and as directed. |
| 24 | Material and labour for precast Cement Concrete chequered tiles of size 200 x 200 x 25mm thick as in floor, set and jointed in neat cement slurry and pointed with cement laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 25 | Material and labour for antiskid vitrified paving / Parking tiles of size 300 x 300 x 10mm thick as in floor, set and jointed in neat cement slurry and pointed with cement laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 26 | Material and labour for machine pressed precast cement concrete interlocking paver blocks 60mm thick and M 35 Grade confirming to IS-15658-2006 and laid over and including 25mm thick sand cushioning complete all as specified and as directed. |
| 27 | Materials and labour for 15 mm thick rendering on fair faces of brick work in cement mortar (1:4) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 28 | Material and labour for applying two coats of cement base paint over a coat of alkali resistant primer including preparation of newly plastered surfaces of wall complete all as specified and as directed. |
| 29 | Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 30 | Supply and fixing MCB DB TPN 4 ways double door with MCB TPN incommer including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and as directed.Note:- MCB TPN, MCB SPN and MCB SP shall be measured and paid seperately under respective item. |
| 31 | Supply and fixing of 100 Amp, 415 Volt, 50 Hz, 4-pole on-load manual changeover switch conforming to IS/IEC 60947-3, with I–0–II switching arrangement, housed in suitable size SS enclosure, complete with operating handle, terminals, cable glands, lugs, earthing arrangement, mounting brackets, nuts, bolts, washers and necessary accessories, including connections, testing and commissioning, complete all as specified and as directed. |
| 32 | Supply and fixing MCB TPN, 240 Volts, of 63 amps current rating, 10 KA breaking capacity ‘C' series complete all as specified and as directed. |
| 33 | Supply and fixing MCB SP, 240 Volts, of 6-32 amps current rating, 10 KA breaking capacity ‘C' series complete all as specified and as directed. |
| 34 | Supply and fixing sub-main wiring with PVC insulated & unsheathed two run of 2.50 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of 2.50 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly as earth continuity conductor, drawn through 20 mm conduit/ Casing Caping with all accessories and PVC rectangular boxes for mounting switch socket and fan regulator etc complete all as specified and as directed. Note : Three runs of 2.50 Sqmm cable and conduit shall be measured as one unit. |
| 35 | Supply and fixing Compact street lighting luminaires with deep drawn housing for single 70 Watt LED, 5700K with toughened glass protection, pressure die cast aluminium housing IP66,with epoxy white powder coated and fixing bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length 1.2 mtr,fixed over the vertical wall through two numbers mild steel clamp of 25mm width, 3mm thick MS flat strip and four Nos nuts, bolts & washers of 12mm dia, 150mm long grouted into wall complete all as specified and as directed. |
| 36 | Supply and fixing LED flood light luminaires, 200 watt, 230 Volt, 50 Hz, LED 5000K, IP66 Metal Halide, grey powder coated die-cast aluminium lamp housing, bult-in control gear, faceted anodised aluminium reflector heat resistant toughened clear glass cover complete including connecting and testing all as specified and as directed. |
| 37 | Supply and fixing 40 Watt LED post top (white colour), 230 volt, 360 degree made in cast aluminium spigot housing with decorative opal acrylic diffuser and IP65 protection including fixing with LED driver and lamp complete all as specified and as directed. |
| 38 | Supply and fixing 10 Watt LED bollard light fitting of cool daylight white colour, having pressure die-cast aluminium housing with corrosion-resistant powder-coated finish, inverted pyramid tripod-type diffuser designed to provide uniform 360° soft light distribution, complete with high-efficiency LED light source of system luminous efficacy greater than 100 lumens per watt, correlated colour temperature (CCT) of 5700 K, power factor greater than 0.95 and minimum IP65 protection against dust and water ingress. The fitting shall be suitable for outdoor installation and provided with integral LED driver, necessary electrical connections, terminal connectors, fixing screws, nuts, bolts, washers and other accessories complete all as specified and as directed. |
| 39 | Supply and laying GI tubing 40mm bore light grade with fittings laid in trenches or for road crossing for protection of LT underground cables complete all as specified and as directed. |
| 40 | Material and labour for HDPE pipe of pressure rating 10 kgf/cm² and dia 32 mm for passing of cable through PCC foundation from trench to distribution board with necessary clamp nuts and bolts complete all as specified and as directed. |
| 41 | Labour only for boring of hole under roads with mechanical arrangement upto 50 mm dia without disturbing the top surface of the road for passing the cable across the road complete all as specified and as directed. |
| 42 | Supply and laying under ground XLPE insulated PVC sheathed (Heavy duty) armoured 1100 volts grade aluminium conductor cable of size 25 Sqmm 4 core laid in trenches as per IS 7098 (Part I) including connection cable glands, aluminium lugs etc. complete all as specified and as directed. |
| 43 | Supply and laying under ground XLPE insulated PVC sheathed (Heavy duty) armoured 1100 volts grade aluminium conductor cable of size 16 Sqmm 4 core laid in trenches as per IS 7098 (Part I) including connection cable glands, aluminium lugs etc. complete all as specified and as directed. |
| 44 | Supply & fixing Three core 1.5sqmm (nominal area) service wire PVC insulated copper conductor FRLS, multi stranded, unsheathed 1100 volts grade IS-694 marked for connection from junction box to street light fitting through steel pole with necessary clamps, bolts, etc required for fixing complete all as specified and as directed. |
| 45 | Supply and fixing steel tubular swaged poles, type 410 SP 31 (Overall length 9.00 meter) conforming to IS-2713 (Part 1 to 3) 1980 complete with cast iron base plate, finial taper plug, bolts, nuts and washers, screws. Pole shall be painted with two coat of black bituminous throughout internally and externally upto planting depth and the remaining external portion shall be painted with two coats of aluminum paints over a coat of red oxide primer, painting black & white alternate strips of 30cm each externally from ground level upto 1.2m with synthetic enamel paint, numbering of poles complete all as specified and as directed.Note: Excavation and earth work and PCC shall be measured and paid separately under respective items. |
| 46 | Supply and fixing of loop-in loop-out (LILO) junction box IP 69 of size 300 × 200 × 110 mm, fabricated from 1.6 mm thick Sheet Moulding Compound (SMC) material, weatherproof, dustproof and verminproof, complete with hinged door, suitable locking arrangement and sloping top cover to prevent accumulation of rainwater. The junction box shall be provided with four (04) Nos aluminium busbars of size 20 × 5 mm, securely mounted on suitable insulated supports, and one (01) No 10 Amp MCB of approved make, including necessary internal wiring, cable entry provisions, terminals and accessories. The junction box shall be securely mounted on the existing pole using suitable size MS flat iron clamps, brackets, nuts, bolts, washers and other necessary fixing accessories complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 47 | Supply and fixing of loop-in loop-out (LILO) junction box IP 69 of size 300 × 200 × 110 mm, fabricated from 1.6 mm thick Sheet Moulding Compound (SMC) material, weatherproof, dustproof and verminproof, complete with hinged door, suitable locking arrangement and sloping top cover to prevent accumulation of rainwater. The junction box shall be provided with four (04) Nos aluminium busbars of size 20 × 5 mm, securely mounted on suitable insulated supports, and one (01) No 10 Amp MCB of approved make, including necessary internal wiring, cable entry provisions, terminals and accessories. The junction box shall be securely mounted on the existing pole using suitable size MS flat iron clamps, brackets, nuts, bolts, washers and other necessary fixing accessories complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysDec 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender