Tender For Special Rep To Replacement Of E/M Items In Various Faculties At Eme School,Vadodara.
Tender Value
31.75 Lakhs
Estimated cost
Bid Submission
09 Dec 2026
17 days left
EMD
63500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Vadodara → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Rep To Replacement Of E/M Items In Various Faculties At Eme School,Vadodara.
BOQ
| Sl. No. | Item Description |
| 1 | Supply, installation, connecting, commissioning and repalcement of LT panel with CPRI approved main factory fabricated LT distribution panel board, outdoor type, both side openable including loking arrangement with sliding door bolt , cubical type, 3 phase, 4 wire, 415V, factory made free standing, floor mounting, dust and vermin proof, cubical type, fabricated from 3.15 mm thick MS sheet with anticorrosive coating and finally epoxy polyster powder coating of flint grey shade fully compartmentalised design with 4Nos insulated bus bar each made of high conductivity aluminium suitable for 630 Amps, prewired with suitable size of copper cable/insulated copper strip for fixing arragement at site suitable earth strips conforming to IS, cable glands, lugs etc including grouting of panel board 1.2 mtr above & 30 cm below ground level duly supported on 50x50x6mm angle iron frame & welding 45 cm long angle iron legs of size 50x50x6mm on all the four corners embedded in PCC 1:2:4 using 20 mm stone aggregate upto 30 cm depth complete all as specified and directed by Engineer-in-Charge suitable for and comprising of the following including taking down old LT panel:-(A) INCOMING MCCB adjustable thermal and magnetic of 350 Amps, 4pole, 415 Volts, 36 KA, with rotary macanism - 01 Nos (B) OUTGOING (i) MCCB adjustable thermal and magnetic of 200 Amps, 4pole, 415 Volts, 36 KA, with rotary macanism - 01 Nos (ii) MCCB adjustable thermal and magnetic of 160 Amps, 4pole, 415 Volts, 36 KA, with rotary macanism - 01 Nos (iii) MCCB adjustable thermal and magnetic of 100 Amps, 4pole, 415 Volts, 16 KA, with rotary macanism - 01 Nos(iv) MCCB adjustable thermal and magnetic of 63 Amps, 4pole, 415 Volts, 16 KA, with rotary macanism - 01 Nos(v) MCB , TPN 'C' Series ,240V/415 V , 50HZ , 63 Amps 10 KA - 01 Nos (vi) MCB , SPN 'C' Series ,240V/415 V , 50HZ , 63 Amps 10 KA - 02 Nos(vii) MCB , SPN 'C' Series ,240V/415 V , 50HZ , 32 Amps 10 KA - 03 Nos(viii) Blank space for MCCBs of same capacity - 01 Nos(ix) Digital Multifuction meter with selector switch and three CT/PT site program of suitable ratio and capacity -01 Set(x) LED Type Phase indicator lamps for three phases set of three -01 Nos(xi) Selector switch - 03 Nos(xii) Busbar chamber having insulated aluminium busbar, each suitable for 630 Amps for three phases and neutral -01 Set |
| 2 | Supply, installation, connecting, commissioning and repalcement of LT panel with CPRI approved main factory fabricated LT distribution panel board, outdoor type, both side openable including loking arrangement with sliding door bolt , cubical type, 3 phase, 4 wire, 415V, factory made free standing, floor mounting, dust and vermin proof, cubical type, fabricated from 3.15 mm thick MS sheet with anticorrosive coating and finally epoxy polyster powder coating of flint grey shade fully compartmentalised design with 4Nos insulated bus bar each made of high conductivity aluminium suitable for 720 Amps, prewired with suitable size of copper cable/insulated copper strip for fixing arragement at site suitable earth strips conforming to IS, cable glands, lugs etc including grouting of panel board 1.2 mtr above & 30 cm below ground level duly supported on 50x50x6mm angle iron frame & welding 45 cm long angle iron legs of size 50x50x6mm on all the four corners embedded in PCC 1:2:4 using 20 mm stone aggregate upto 30 cm depth complete all as specified and directed by Engineer-in-Charge suitable for and comprising of the following including taking down old LT panel:-(A) INCOMING MCCB adjustable thermal and magnetic of 400 Amps, 4pole, 415 Volts, 36 KA, with rotary macanism - 01 Nos (B) OUTGOING (i) MCCB adjustable thermal and magnetic of 350 Amps, 4pole, 415 Volts, 36 KA, with rotary macanism - 01 Nos (ii) MCCB adjustable thermal and magnetic of 250 Amps, 4pole, 415 Volts, 36 KA, with rotary macanism - 01 Nos (iii) MCCB adjustable thermal and magnetic of 160 Amps, 4pole, 415 Volts, 36 KA, with rotary macanism - 01 Nos(iv) MCCB adjustable thermal and magnetic of 100 Amps, 4pole, 415 Volts, 16 KA, with rotary macanism - 01 Nos(v) MCB , TPN 'C' Series ,240V/415 V , 50HZ , 63 Amps 10 KA - 03 Nos (vi) MCB , SPN 'C' Series ,240V/415 V , 50HZ , 63 Amps 10 KA - 04 Nos(vii) Blank space for MCCBs of same capacity - 01 Nos(viii) Digital Multifuction meter with selector switch and three CT/PT site program of suitable ratio and capacity -01 Set(ix) LED Type Phase indicator lamps for three phases set of three -01 Nos(x) Selector switch - 03 Nos(xi) Busbar chamber having insulated aluminium busbar, each suitable for 720 Amps for three phases and neutral -01 Set |
| 3 | M & L in repair for fabrication of bus bar chamber of size 80cmx60cmx40cm for 415 volts 3 phase 4 wire system withMCCB adjustable thermal and magnetic of 200A ,36 KA ,4 pole, outdoor type, with digital volt amp meter ,double door, withpedestal mounted, weather and vermin proof fabricated out of 3.15 mm thick MS CRCA sheet with anti corrosive coating & finally epoxy polyster powder coating of flint grey shade including 3 nos. phase indicating lamps, insertion of suitable cable glands for all incoming and out going cable including grouting of panel board 1.2 mtr above & 30 cm below ground level duly supported on 50x50x6mm angle iron frame & welding 45 cm long angle iron legs of size 50x50x6mm on all the four corners embedded in PCC 1:2:4 using 20 mm stone aggregate upto 30 cm depth complete all as specified and directed by Engineer-in-Charge .Note :- Comprising of 4 nos. Aluminium bus bar 200 Amp for phases & 100 Amp for neutral mounted on DMC/ porcelain insulator support complete all as specified and directed. |
| 4 | Earthing Complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.5 metre below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connection by using galvanized earth lead wire 32 x 6 mm dia by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and other end of the earth wire connected to main switch board protected by galvanised iron medium grade pipe 40mm bore in wall/floor/and GI Pipe 20 mm bore light grade for watering with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC pit cover including necessary excavation and earth work in any type of soil, returning slurry approved soil and disposed of surplus soil to a distance not exceeding 50 Mtr away all as shown in electrical plate No 3 of SSR 2009 ( Part-I).Notes (a) The unit rate shall include for GI protection pipe, GI watering pipe, wire mesh, funnel and excavation, RCC pit cover, test point, galvanised iron strip from top of earth plate upto 7.5 metres above ground level and if GI protection pipe is less than 7.5 metres, no price adjustment shall be made.(b) PCC pit shall be provided at least 50cm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junction, elbow etc shall be deemed to be included in the unit rate.(c) If the testing result of earthing is not found below 3 Ω then the contractor shall do another earthing work at his own cost and nothing shall be permissible on this account.(d) Earthing work will be carried out in presence of MES representative. |
| 5 | Supply and Fix in replacement of 40/45 watt LED post top lamp New generation IP 65, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source.T40WLED757PSYMTOPCvells , LPTO-40-CDL-Mor of Crompton ,LP02-501-X7-XX of Wipro Note :- The warranty on light should be minnimum of 2 Years . Please Enable Macros to View BoQ information |
| 6 | Supply and Fix in replacement of 40/45 watt LED post top lamp New generation IP 65, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source.T40WLED757PSYMTOPCvells , LPTO-40-CDL-Mor of Crompton ,LP02-501-X7-XX of Wipro Note :- The warranty on light should be minnimum of 2 Years . Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysDec 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender