Defence Statutory Bodies & Commissions/Committees Closing in 20 days TDR #58618274

Tender For Special Repairs To Doors And Windows In Bldg No P-461, P-462 And P-463 In Kta Under Ge(I) Gos

Issued by Statutory Bodies & Commissions/Committees · Ganjam, Odisha
Tender Value
Ref. Documents
Estimated cost
Bid Submission
12 Dec 2026
20 days left
EMD
89000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Ganjam → Odisha
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Special Repairs To Doors And Windows In Bldg No P-461, P-462 And P-463 In Kta Under Ge(I) Gos

BOQ

Name of Work:- SPL REPAIRS TO DOORS AND WINDOWS IN BLDG NO P-461, P-462 AND P-463 IN KTA UNDER GE(I) GOS
Sl. No. Item Description
1Demolition of cement concrete (unreinforced) in windows around the cill level n exc 15 cm thickness complete all as specified and directed
2Demolition of brick work or stone/ boulder masonary built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.
3Demolition of reinforcement cement concrete above the ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as RCC Almirah, platform, chajjas etc complete all as specified and directed.
4Dismantling of tile, floor, hearth, walls, roof tiles,kota stones etc including bedding (but not backing), and rubbish off permises complete all as specified and directed.
5M&L Brick work with Fly Ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.
6M&L for PCC 1:2:4 type B1 using 20 mm or 12.5 mm graded stone aggregate as in around the windows cill and jams,coping, benching, etc as per site requirement, including necessary form work etc,surface finished even and fair complete all as specified and directed
7M&L Rendering on fair faces of brick work or concrete surfaces of wall 15 mm thick in CM 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed.
8M&L Rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall, soffits, etc as in & around the windows cills, jambs, etc complete all as per site requirement on minimum wall width exc 230 mm but n exc 400 mm finished even and smooth without using extra cement complete all as specified and directed.
9M&L for non skid ceramic coloured tiles of any shade design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor or vertical surfaces etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.
10M & L coloured vitrified tiles of any colour/ any shade 8 to 10 mm thick (square/rectangular) polish area of each tiles n exc 0.36 Sqm coloured cut to required size set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles as in floor or vertical surfaces incl 15 mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge/GE.
11Taking down MS Windows and including MS Grill/ chowkats or frames with shutters of any description (without taking off shutters from the frames) area n. exc 1.5 Sqm each and removing to store complete all as specified and directed.
12Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed
13Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed
14Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) and including 5.5 mm thick glass selected with quality and 15 mm uPVC panel board all as specified and directed by Engr-in-Charge.
15S&F factory made UPVC white colour Slinding Window three track made of extruded profiles with wall thickness of 2.3mm (±0.2mm), Window profile with hollow section with multi chamber, frame (88mm X 52mm), sliding sash (42mm X 67mm), Sliding mesh sash (42x57mm), sliding interlock (one vertical length in each shutter) (45.5mm X 28mm), glazing bead (24.5mm X 16mm) will be mitered, cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware, EPDM gasket 1.2 ± 0.2mm thick galvanised steel frame (30mm x 18mm) 2 Nos, sliding sash (30mm X 18mm) 2 Nos, sliding mesh sash (26mm X 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Haradware (tough lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of apaerture 1.40mm and required accessories and including 5.50 mm glass with selected quality. all as specified and directed by Engr-in-Charge.
16S&F 5-6 mm thick aluminium grills of make \\"Decogrill' model DG 104 surrounded by aluminium 'C' channel with mesh size 99 X 105 mm all as specified and directed.
17S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of watertanks and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.
18Supply and fixing factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension,including Pinhead Glass with thickness of 4mm required for fixing & louvers strips, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in imension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
19M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in treads & risers of steps, skirting, dado, jambs, window-cills, jams etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and also including granite anti slip grooves (minimum 3 grooves for one tread) complete all as specified and directed by Engr-in-Charge.
20Rounding to edges of stone slabs one edge such as steps or treads in stair case complete all as specified and directed.
21M&L for preparation of old/new plastered surfaces of walls or concrete surfaces and applying 3 mm thick wall care putty complete all as specified & directed.
22M&L for complete removal of existing treatment and applying two coats of OBD over a coat of alkali resistant primer on wall complete all as directed by Engineer-in-Charge.
23M&L applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on newly plastered wall surfaces/ old decorated wall surfaces, in case of old decorated wall surfaces includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed.
24M&L and repair of patch work not exceeding 1 sqm each place as per site requirement & Rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finish the surfaces even and smooth without using extra cement including WPC complete all as specified and directed.
25Taking down eaves gutters and rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.
26S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.
27S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.
28S&F Stack clamps made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110 mm PVC pipe complete all as specified and directed.
29S&F PVC(SWR) bends, any radius of 110 mm bore without access door complete all as specified and directed.
30S&F PVC(SWR) bends, any radius of 110 mm bore with access door complete all as specified and directed.
31S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and directed.
32M & L applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete.
33S&F in repair for 25mm dia Stainless Steel Curtain Rod complete all as specified and directed.
34S&F fancy type heavy duty easy-to-fit wall-to-bracket holder for for 25mm dia stainless steel curtain rod, as per site requuirement approved by Engr-in-Charge complete all as specified and directed
35M&L for Treatment of soil using emulsion for Post construction Anti termite Treatment along the face of extrnal or internal wall, on periphery of Window/ door/ ventilator and its sides using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in wall or floor and the like complete all as specified and directed.
36M&L two coats of distempering with 1st quality acrylic distermer (ready mixed) having VOC contents less than 50 gms/ltr of approved manufacturer, of required shade and colour complete as per manufacturers specification after preparation of plasterd surface including a coat of primer on prepared surfaces including, rubbing with sand paper and applying (Plastic Emulsion) complete all as specified and directed.
37M&L preparation of old painted surfaces and applying one coat of oil bound distemper on walls complete all as directed by Engineer-in-Charge
38Taking down cement or cement lime plaster, any description on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58618274
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE Ref. Documents
LAST DATE 12-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Special Repairs To Doors And Windows In Bldg No P-461, P-462 And P-463 In Kta Under Ge(I) Gos
Basic Detail
Tender No GE/GOS/TOK/162 OF 2026-27
Bidding Type Tender
Location
City Ganjam
State Odisha
Key Dates
Publish Date 19 Nov 2026
Submission Date 12 Dec 2026
Open Date 17 Dec 2026
Finance
Tender Value Ref. Documents
Tender Fee 500
EMD 89000
Exemption Not Available
Document List
bff4dd79-e395-4c10-b954-dbd210b1af0e.html
BOQ_896221.xls
Tendernotice_1.pdf
Tender_DOCS.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 19, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 12, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 20 days
Dec 17, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 25 days

Tender Documents

Download All (ZIP) ↓
html

bff4dd79-e395-4c10-b954-dbd210b1af0e.html

xls

BOQ_896221.xls

pdf

Tendernotice_1.pdf

pdf

Tender_DOCS.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender