Science and Technology Government Departments Closing in 18 days TDR #58612374

Tender For Revamping Of Air Handling Units With Associated Piping, Ducting Etc. At Various Locations Of Igcar, Kalpakkam. Note : 1.This Schedule Must Be Read Along With The Drawing, Specification And Scope Of Work (Section V) And General Specificatio

Issued by Government Departments · Chengalpattu, Tamil Nadu
Tender Value
1.42 Crore
Estimated cost
Bid Submission
08 Dec 2026
18 days left
EMD
2.84 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Chengalpattu → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Revamping Of Air Handling Units With Associated Piping, Ducting Etc. At Various Locations Of Igcar, Kalpakkam. Note : 1.This Schedule Must Be Read Along With The Drawing, Specification And Scope Of Work (Section V) And General Specifications (Section Vi) For Complete Interpretation Of This Scope Of Work Quantitywise. 2.Items Of Work Described In Brief Below Are Detailed Under Specification Of Work. The Scope Of Work Will Not Be Estimated From The Brief Description Of This Schedule. 3.Rate Quoted Must Include All Components Required For Meeting The Specification And Performance Requirements Of The Item Irrespective Of Whether They Are Specifically Brought Out In This Schedule Or Not. 4.Tenderers Are Advised To Get Acquainted With The Site Conditions Before Quoting. 5.Schedule Rate Shall Be Firm And Overall Conditional Discount For The Total Tendered Amount Will Not Be Accepted. 6. Rate Quoted Should Be Inclusive Of All Taxes Including Gst.

BOQ

Name of Work:- Revamping of Air Handling Units with associated piping, ducting etc. at various locations of IGCAR, Kalpakkam. Note : 1.This schedule must be read along with the drawing, Specification and scope of work (Section V) and General Specifications (Section VI) for complete interpretation of this scope of work quantitywise. 2.Items of work described in brief below are detailed under Specification of Work. The scope of work will not be estimated from the brief description of this schedule. 3.Rate quoted must include all components required for meeting the specification and performance requirements of the item irrespective of whether they are specifically brought out in this Schedule or not. 4.Tenderers are advised to get acquainted with the site conditions before quoting. 5.Schedule Rate Shall be firm and Overall Conditional Discount for the Total Tendered amount will not be accepted. 6. Rate Quoted Should be inclusive of all taxes including GST.
Sl. No. Item Description
1Supply, installation, testing and commissioning of factory built, floor mounted double skin type horizontal chilled water air handling units made of 25 ± 1 mm thick panels consisting of pre-plasticized G.I /Pre painted Galvanised Sheet Steel with PVC guard film, Polyamide thermal break profile for ensuring thermal bridging performance casing of thickness 0.8 mm outside layer and Aluzinc of 0.8 mm inside layer with Polyurethane foam (PUF) insulation, factory injected between them by injection moulding machine, complete with Aluminum alloy SISW fans (minimum static efficiency(ŋ ≥ 75%) at selected duty conditions with EC/BLDC motor mounted on sturdy SS frame, minimum 2 mm thick stainless Steel (SS 304 / SS 316) base frame, minimum 2 bend PVC eliminators, aluminum finned copper tube cooling coil (tubes thickness not less than 0.5 mm), heresite coated, 6 row deep, 1.2 mm thick SS 304 coil casing, copper header with end connection suitable for MS/GI pipeline, UV lamp for coil section with necessary controls, pre-filter section with 50 mm thick panel type with aluminum frame and aluminum mounting frame, water washable synthetic type air pre-filters, EC drive motor with suitable speed control for operating voltage 415 ± 10% V, 50Hz, 3 Phase AC supply, drain connections, stainless steel (18G) drain pan with nitrile foam insulation, vision panel, sturdy 16G lever operated discharge damper, marine light, full height access door with motor interlock, necessary vibration isolation arrangement etc. complete as per detailed specification and of following capacities.
210 TR, 5000 CFM, 6 ROW DOUBLE SKIN AHU, 30 mm WC ESP
315 TR, 6000 CFM, 6 ROW DOUBLE SKIN AHU, 30 mm WC ESP
430 TR, 12000 CFM, 6 ROW DOUBLE SKIN AHU, 30 mm WC ESP
535 TR, 14000 CFM, 6 ROW DOUBLE SKIN AHU, 30 mm WC ESP
640 TR, 16000 CFM, 6 ROW DOUBLE SKIN AHU, 30 mm WC ESP
760 TR, 24000 CFM, 6 ROW DOUBLE SKIN AHU, 30 mm WC ESP
8Supply, installation, balancing and commissioning of site/factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.
9Factory fabricated/ In-situ fabricated GSS duct of sheet size 0.85mm (22G)
10Supply and fixing of following thickness duly laminated aluminium foil closed cell Nitryle foam rubber/cross linked polyethylene (Class \\"O\\") Thermal insulation on existing duct, valves & pipes after applying suitable adhessive or shall have self adhesive on one side and aluminum foil of 40G thick on outer side as per the specifications and complete as required. All the joints shall be properly sealed with 150 mm wide nitrile rubber insulation and complete with self adhesive aluminum sealing tape.
119 mm Closed cell Nitryle foam rubber/cross linked polyethylene Thermal Insulations
12Supply and fixing of following thickness Fibre free and antimicrobial resistant, Open cell elastomeric nitrile rubber acoustic insulation in supply air ducts with fire retared \\"O\\" class, fire performance, resistant to chemical & micro organism and sound absorption class-D as per the technical specification and complete as required.
1325 mm Open Cell elastomeric nitrile rubber acoustic insulation
14PUF INSULATED CHILLED WATER PIPING WITH ALUMINIUM CLADDING: Supply, installation, testing and commissioning of factory fabricated pre-insulated pipes consisting of MS carrier pipes, PUF insulation and aluminum outer jacket as per specification complete with bends, flanges etc including site fabrication, welding and field insulation. The carrier pipe shall be of carbon steel ERW conforming to IS 1239/3589 (grade Fe330) supplied in 6m ± 100 mm standard length only All pipes shall be brand new, flawless and free from any rust, corrosion and deterioration. The insulation shall be applied by injecting the polyurethane foam into the annulus between carrier pipe and pre-extruded aluminum outer jacket pipe in accordance to ASTM C 591 or by spraying the foam directly onto the pipe and extruding the jacket directly on top of the foam in accordance to ASTM C 1029 type III. The insulation shall have minimum core density of 42 kg/m3, 90% minimum closed cell content minimum compressive strength of 310 kPa and maximum thermal conductivity of 0.03 W/mK at 24°C. The outer jacket shall be formed from 24 G aluminum sheet conforming to IS 277.The pre-insulated pipes shall be supported on 75 mm thick PUF saddles and clamped firmly with GI U-clamps on MS supports. Note: Item includes supply, loading, transportation, unloading, safe storage,erection of pipelines using crane on existing structure and pulling the pipes using hydraulic equipments and arranging for fitup.
15100 NB, 50 mm thick Pre-insulated chilled water piping (Al cladding)
1680 NB, 50 mm thick Pre-insulated chilled water piping (Al cladding)
1750 NB, 50 mm thick Pre-insulated chilled water piping (Al cladding)
1840 NB, 50 mm thick Pre-insulated chilled water piping (Al cladding)
19Supply and installation of EPDM rubber / Nitrile foam sheet field insulation over chilled water pipes as per specification complete with bends, flanges etc. The EPDM rubber / Nitrile foam sheet shall be of 40-60kg/m3, thermal conductivity 0.0352 W/mK @24 C, temperature range 0 to 50° C, class V - 0 fire rated as per UL 94, flammability and smoke density shall be 15/50 as per ASTM E84, water vapour diffusion resistance factor ≥ 7000, water absorption ≤ 5% by weight as per ASTM D 1056. Insulation shall be free from nitrosamine contents, CFC and microbiological growth as per relevant standards.
2032 mm thick Nitrile foam insulation for 100NB chilled water pipes
2125 mm thick Nitrile foam insulation for 80NB chilled water pipes
2225 mm thick Nitrile foam insulation for 50NB chilled water pipes
2325 mm thick Nitrile foam insulation for 40NB chilled water pipes
24Supply & Fixing of volume control adjustable type opposed blade Damper with necessary flanges for duct branches with PVC gears. The Dampers shall be made out of 14G Aluminium channel as per the specification in Secton -V. The opposed blades shall have tie rod with ball & socket joints.
25Volume Control Damper made with Aluminium
26Fabrication of pipe lines: Site fabrication of MS pipes including edge preparation, fit up,welding (root pass-TIG & final pass-arc) and testing. The testing includes 100% DPT on both root & final weld and Hydro test at every 100m length at 10 kg/cm2 after final completion.
27Fabrication of pipe lines
28Dismantling of MS/GI structures, chilled/condenser water MS pipes,AHU, etc and safe handover to CWCP/Department stores. It includes cutting & loading, shifting of removed materials by means of mobile crane, if any, as per the standard practice and as specified within the lead distance of 2 km.
29Dismantling, loading & unloading, seggregation of pipes,AHU includes motor,blower, PUF panels, collection of PUF insulation from site and proper disposal as per EIC Instruction, Al frame, GI /MS structural items etc to work site within 2km lead.
30Supply, fixing, testing and commissioning of butterfly valves with CI body SS disc, Nitrile rubber seal & O-ring PN-16 pressure rating for chilled water
31100mm butterfly valve without insulation
3280mm butterfly valve without insulation
3350mm butterfly valve without insulation
34Supply and installation of forged brass ball valve. The stem, body, ball and gland nut shall be forged brass as per IS 6912 Gr. FLB nut & washer of carbon steel as per IS 1367, gland packing and body seat ring shall be PTFE as per BS EN 12086-1, operating lever shall be CS as per IS 2062, test pressure body- 25 kg/sqcm and seat 16kg/sqcm.
3525 mm Brass Ball Valve
36SS BODY PRESSURE GAUGE Supply and installation of 100 mm dial type SS316 pressure gauge with range 0-10kg/sqcm, direct mounting bottom Entry, 3/8'' BSP (M/FM), Accuracy+/- 2% FSD over Range 130% of FSD, SS body & wetted parts, SS syphon and 15 mm dia SS needle valve, suitable for Temperature upto 70 Deg C complete as required.
37SS body, 100 mm dial type, 0-10 kg/sq.cm Pressure gauge
38SS BODY TEMPERATURE GAUGE Supply and installation of 100 mm dial type SS316 body bimetal temperature gauge of range 0-50°C, 12\\" long stem x 10 mm OD, horizontal mounting, 1/2\\" BSP (M/FM) connection with SS thermowell socket for fixing / inserting thermometer. The temperature gauge shall be made by SS 316 complete as specified.
39SS body, bimetal temperature gauge
40SS NIPPLESSupply and erection of SS 304, Sch 40 seamless pipe nipples of 200 mm long as per ASTM
4125 mm SS Nipples
42SUPPLY AND INSTALLATION OF GI FASTENERS
43M 16 x 50 mm long GI hexagonal head fasteners with 2 nos of 3 mm thick GI plain washers.
44M 16 x 100 mm long GI hexagonal head fasteners with 2 nos of 3 mm thick GI plain washers.
45GASKETS
46The scope of work includes the supply and installation of new asbestos type water gasket with a thickness of 3mm, a width of 1m, and a suitable length as required. The gasket material shall be of high quality and suitable for water sealing applications..
47Supply of MS structural items like plates, angle, channel etc as per IS 2062, Fe 250 grade, fabrication and erection of MS structure to suit conditions by ARC welding process which include edge prepation fit up root and final die penetration test.
48Supply, Fabrication and erection of MS structures
49Supply and erection of pipe fittings and accessories as per specification.
50100 mm slip on flange
5180 mm slip on flange
5250 mm slip on flange
5340 mm slip on flange
54Supply and erection of MS seamless, long radius sch 40 elbow as per IS 11428
55100 NB 90 deg elbow
5680 NB 90 deg elbow
5750 NB 90 deg elbow
5840 NB 90 deg elbow
59SS COUPLING SS 304/316, Full Coupling, Class 3000, threaded female × female ends, NPT threads conforming to ASME B1.20.1, manufactured in accordance with BS 3799.
603/8 inch
6125 NB
62Supply and erection of MS seamless, Sch 40 concentric reducer as per IS 11428.
63100 x 80 NB Concentric Reducer Sch 40
6480 x 65 NB Concentric Reducer Sch 40
6550 x 40 NB Concentric Reducer Sch 40
6640 x 32 NB Concentric Reducer Sch 40
67In-situ fabrication and installation of aluminum sheet cladding over chilled water pipe lines, valves, etc as per approved drawings and specifications of following sheet thickness complete as required. The aluminium sheet shall be conforming to IS 277.
68Fabrication of 24G (0.6 mm) aluminum sheet cladding
69Supply and installation of the following sizes of copper wires in built in trench as per the detailed specification.(Refer Sec VI, Clause No.12.8)
708SWG copper wire
7114 SWG Copper Wire
72Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade following sizes of cables in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification.(Refer Sec VI, Clause No.3)
734C X 10 sqmm 1.1kV grade Copper conductor PVC insulation flat wire armour FRLSH PVC outersheath
744C X 16 sqmm 1.1kV grade Copper conductor PVC insulation flat wire armour FRLSH PVC outersheath
75End Termination of the following size Copper Conductor PVC/XLPE Insulated and FRLS sheathed armoured UG Cable using Single Compression, Heavy Duty, Siemens type Brass Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Copper crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for fixing cable gland. (Refer Sec VI, Clause No.10.1).
764C x 10 Sq.mm including cable gland earthing
774C x 16 Sq.mm including cable gland earthing
78Removal of the following from 415Volts switch boards (Refer Sec VI (MNC), Clause No.19).
7963A/100A/125A, 500V, TP/TPN/SFU/ Combination SFU or 4/6/8/12 Way SPN DB or 4/8 WAY TPN DBs / motor strater units
80Retrieval of the already laid one number 1100 Volts Grade XLPE/HRPVC insulated, Stranded Aluminium conductor cables of following sizes in built-in trenches, on walls, poles and from embedded pipes including removal of end termination GI spacer, clamps etc as per the detailed specification. (Refer Sec VI, Clause No.5)
813/3.5/4 Core upto 25 Sqmm
82Cable tray: Perforated 2.0 mm thick GI cable tray with cover (minimum 70 µ coating thickness) of 200 x 50 x 10 mm size including all accessories and MS mounting support.
83Manufacturing, supplying, hoisting and fixing in position at all lifts, precast units of various patterns and sizes for precast plain solid units, slabs, exhaust fan moulds etc., in reinforced cement concrete of 1:2:4, using 20mm and below machine crushed graded stone aggregate including weigh batching, mechanical mixing, casting, vibrating, finishing of exposed faces, curing, necessary formwork & moulds, transporting and placing at all lifts, preparation of connections, grouting with cement mortar/cement grout wherever needed excluding steel reinforcement complete all as per drawing, specification and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58612374
AUTHORITY Government Departments
TENDER VALUE 1.42 Crore
LAST DATE 08-12-2026
Authority
Authority Name Indira Gandhi Centre For Atomic Research
Work Description Tender for Revamping Of Air Handling Units With Associated Piping, Ducting Etc. At Various Locations Of Igcar, Kalpakkam. Note : 1.This Schedule Must Be Read Along With The Drawing, Specification And Scope Of Work (Section V) And General Specifications (Section Vi) For Complete Interpretation Of This Scope Of Work Quantitywise. 2.Items Of Work Described In Brief Below Are Detailed Under Specification Of Work. The Scope Of Work Will Not Be Estimated From The Brief Description Of This Schedule. 3.Rate Quoted Must Include All Components Required For Meeting The Specification And Performance Requirements Of The Item Irrespective Of Whether They Are Specifically Brought Out In This Schedule Or Not. 4.Tenderers Are Advised To Get Acquainted With The Site Conditions Before Quoting. 5.Schedule Rate Shall Be Firm And Overall Conditional Discount For The Total Tendered Amount Will Not Be Accepted. 6. Rate Quoted Should Be Inclusive Of All Taxes Including Gst.
Basic Detail
Tender No IGCAR/ESG/ACVSD/T-292/2026
Bidding Type Tender
Location
City Chengalpattu
State Tamil Nadu
Key Dates
Publish Date 19 Nov 2026
Submission Date 08 Dec 2026
Open Date 09 Dec 2026
Finance
Tender Value 1.42 Crore
Tender Fee Ref. Documents
EMD 2.84 Lakhs
Exemption Not Available
Document List
2866437d-7b3f-4fda-bea6-d17ebc650ea8.html
BOQ_982499.xls
tenderdocument.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 19, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 08, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 18 days
Dec 09, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 19 days

Tender Documents

Download All (ZIP) ↓
html

2866437d-7b3f-4fda-bea6-d17ebc650ea8.html

xls

BOQ_982499.xls

pdf

tenderdocument.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender