Public Administrative Department Government Departments Closing in 25 days TDR #58603901

Tender For Under District Barabanki, 12 Teaching Rooms, Barabagda, Floor, Plaster, Windows, Doors, Painting, And Personal Repairs At Bhakt Dalganjan Vidyapeeth Inter College Khajuri, Block Dariyabad, Barabanki, Etc., Lot No 1

Issued by Government Departments · Ayodhya, Uttar Pradesh
Tender Value
37.81 Lakhs
Estimated cost
Bid Submission
15 Dec 2026
25 days left
EMD
76000
Bank guarantee accepted
Document Fee
2354
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Ayodhya → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Under District Barabanki, 12 Teaching Rooms, Barabagda, Floor, Plaster, Windows, Doors, Painting, And Personal Repairs At Bhakt Dalganjan Vidyapeeth Inter College Khajuri, Block Dariyabad, Barabanki, Etc., Lot No 1

BOQ

Name of Work:- Under District Barabanki, 12 teaching rooms, Barabagda, floor, plaster, windows, doors, painting, and personal repairs at Bhakt Dalganjan Vidyapeeth Inter College Khajuri, Block Dariyabad, Barabanki, etc., Lot No 1
Sl. No. Item Description
1E/W in excavation by mechanical means (Hydraulic Excavatory)/manual means in foundation trenches or drain (Not exceeding 1.5m in width or 10 sqm on plan). I/c dressing of sides and ramming of bottoms, for all lift, i/c getting out the excavated soil and disposal of surpluse excavated soil as directed, within a lead of 50 m. DSR 2.8
2Providing and laying in position in C.C specified grade excluding the cost of centering, shuttering ,finishing and reinforcement ( 1:6:12)with cement , Fine sand and 40mm gauge B/ ballast i/c all as per pwd spacifications no 273
3Brick work with common bruint clay F.P.S. (Non Modular) Brick of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 Cement ; 6 coarse sand) DAR NO. 6.1.2)
4Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete Name of Work:- PROPOSED ESTIMATE FOR CONSTRUCTION OF B.R.C. BUILDING AT BARABANKI ABSTRACT OF COST (Based on CPWD D.S.R.-2023 & Market Rates) (plinth area of the building at ground floor only shall be measured as per I.S.6313 (Partll 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. The rate of application of chemical emulsion shall be as follows : (1) Treatment for masonary & foundation 5 liters per sqm. (2) Back fill in immediate contact with foundation 7.5 liters/sqm (3) Treatment of top surface of plinth filling 5 liters/sqm (4)Treatment junction of wall and the floor 7.5 liters /sqm (5) Treatment of soil along external perimeter of building 7.5 liters/sqm (6) Treatment of soil under apron along external perimter 5 liters/sqm. (As per manufacturer'sstandard dilution) DSR 2.35.3.1
5Brick work with common bruint clay F.P.S. (Non Modular) Brick of class designation 7.5 in supper structure above plinth up to floor v level in all shapes and sizes cement mortar 1:6 (1 Cement ; 6 coarse sand) DAR NO. 6.4.2
6Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 5.2.2
7Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6
8Structural steel work riveted, bolted or welded in built up sections, truesses and framed work. i/c cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR 10.2
9Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 5.1.2
10Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Concrete of M25 grade with minimum cement content of 330 kg /cum DSR 5.33.1.1
11Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete DSR 5.9.1
12Providing and fixing 35 mm thick shutters panelled or panelled and glazed shutters for doors. Windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of engineer-in-charge. (Note Butt hinges and necessary screws shall be paid seprately) DSR 9.5.3.1
13Steel reinforcement for RCC work i/c straightening, cutting, bending, placing in postion and binding all complete upto plinth level and above plinth levet Thermo-Mechanically treated bars of grade Fe-5000D or more. DSR No. 5.22.6 or 5.22A.6
1412mm thick cement plaster Mixe 1:6 cement fine sand mix mortar in plinth ( inner side) DSR 13.1.2
15Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. DSR 11.3.1
16Supply & glass strip in joints for terrazo/cement concrete floors 40 mm wide and 4 mm thick. DSR 11.13.1
17Excavating, supplying, stacking and filling of local earth (i/c royalty) by mechanical transport upto a lead of 5km also i/c remming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinths, sides of foundation etc. complete for all lift. DAR No. 2.25(a)
18Providing & applying white cement based putty of aveage thickness 1mm of approved brand and manufacturer ove the plastered wall surface to prepare the surface even and smooth complete SI No DSR 13.80
19Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. 13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. DSR 13.48A.1
20Painting with synthetic Enamel paint of approved brand and manufacture of required colour to give and even shade, Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture DSR 13.62.1
21Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. (Floor Tiles) DSR 11.40
22Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Wall Tiles) DSR 8.31
23Providing and fixing water closet squatting pan (Indian type W.C. pan of size 580×440mm with ingegral type foot rests ) with 100 mm sand cast Iron P or Strap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required Same as above but for Indian type W.C. pan DSR 17.1.1
24Providing and fixing wash basin with C.I. brackets,15 mm C.P. brass pillar taps, 32 mm C.P. brasswaste of standard pattern, including painting offittings and brackets, cutting and making good thewalls wherever require a) White Vitreous China Flatback wash basin size 550x 400 mm with single 15mm C.P. brass pillar tappillar tap. DSR 17.7.4
25Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Flexible Pipe 32 mm dia DSR 17.28.2.1
26Providing & fixing C.P. brass long body bib cockof approved quality conforming to IS standardsand weighing not less than 690 gms. DSR 18.51.1
2713 Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brassthreaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction ofEngineer in Charge. 40 mm nominal outer dia Pipes DSR 18.7.4
2813 Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brassthreaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction ofEngineer in Charge. 25 mm nominal outer dia Pipes DSR 18.7.3
29Providing and fixing gun metal gate valve with wheelof approved quality. 25 mm nominal bore DSR 18.7.1
3024 Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for circular tank. DSR 18.48
31Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with mdular type switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. DSR 1.3.3
32Circuit/ Sub main wiring in PVC conduit:-Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.
332 X 1.5 sq. mm+ 1 X 1.5 sq. mm earth wire. DSR 1.14.1
34Sand Filling-Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
35PCCProviding and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
36Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
37Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum
38Footing
39Column
40Plinth
41Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum
42Lintel
43Column
44Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete . Thermo-Mechanically Treated bars of grade Fe-500D or more.
45upto plinth
46above plinth
47Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
48Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)
49Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. Providing & fixing of hold fast for chaukhats of doors and windows.
50Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete fixed to steel window by welding (Window Grill)
51Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 40x40x5 mm, joints mitred and welded by angle iron 40x40x5 mm or 40x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. Providing & fixing of hold fast for chaukhats of doors and windows.
52Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete (Tie Rod)
53Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) (Z-Section)
54Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes
55Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
56Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) (300x16mm)
57Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) (250x10mm)
58Providing and fixing ISI marked oxidised M.S. handles conforming to 1S:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378) 125mm)
5915 mm cement plaster on rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand)
6012 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)
61Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
62Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm. D.S.R. 11.46.2
63Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an evenshade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
64Finishing walls with Primer Acrylic smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67ltr/10 sqm over the including base coat of water proofing cement paint applied @ 2.20 kg/10 Sqm.
65Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer
66Centering and shuttering including strutting, propping etc. and removal of form: in Foundations, footings, bases of columns, etc. for mass concrete
67Centering and shuttering including strutting, propping etc. and removal of form in Suspended floors, roofs, landings, balconies and access platform
68Centering and shuttering including strutting, propping etc. and removal of form in Lintels, beams, plinth beams, girders, bressumers and cantilevers
69Centering and shuttering including strutting, propping etc. and removal of form in Columns, Pillars, Piers, Abutments, Posts and Struts
70Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
71Group C
72Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
73Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
742 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
752 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
76MCB's & DB’s :
77Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
78100 A,30KA,FPMCCB
79Supply and Fixing of LED Tube Light with batten suitable for up to 1X22 watt LED tube light fitting complete including tube on surface complete in all respect.
80Supply and burying of 600mm x 600 mmx6mm G.I. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm G.I.pipe and funnel for watering and two earthing leads of No.8to10SWG G.I.wire in 15mm diaG.I. pipe upto switch board (from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm. square C.I. frame with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects.
81Supply and burying of 40mm dia x 4.5 metres long G.I. pipe, vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No.6 to 8SWG G.I.wire in G.I. pipe upto appron (and from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) upto switch board, 30cm. square C.I.box with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects.
82Erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick G.I. down rod 19mm dia duly painted, complete in all respects.
83S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16 SWGM.S. sheet incorporating 10mm dia, M.S. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour T & P etc., for proper completion of work.
84Supply fixing of electronic fan regulator (Modular) 120-280 V. ISI marked, on the existing switch board including making connetion, required material, labour T/P etc for proper completion of work to the satisfaction of Engineer in charge of work.
85Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. or as directed by the Engineer-Incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc.
8625.0 sq Mm*3.50 core.
87Supply & erection of AC 1200mm Sweep, 230/250 Volts, 50 Hz ceilling fan with standard down rod, blades including connection etc. complete as required-.
88S/F Inaugration black granite (Polished) 20mm thick stone size 0.90x0.75m. including lettering, printing, border etc. will be painted of superior quality is required shade and colour including fixing excavation of foundation (1.40x0.50x0.40 m), P.C.C. 1:6:12 (1.40x0.50x0.10m), brick work 1:4 cement coarse sand foundation (1.40x0.345x 0.30m) ,upto (1.40x0.23x1.35 m),12mm thick plaster 1:4 cement coarse sand and finishing walls with water proffing white cement paint of approved make and quality such as super snowcem paint etc. all complete. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58603901
AUTHORITY Government Departments
TENDER VALUE 37.81 Lakhs
LAST DATE 15-12-2026
Authority
Authority Name Rural Engineering Department
Work Description Tender for Under District Barabanki, 12 Teaching Rooms, Barabagda, Floor, Plaster, Windows, Doors, Painting, And Personal Repairs At Bhakt Dalganjan Vidyapeeth Inter College Khajuri, Block Dariyabad, Barabanki, Etc., Lot No 1
Basic Detail
Tender No 2071/SE RED Ayodhya/Barabanki/26-27 Dt 22/09/2026
Bidding Type Tender
Location
City Ayodhya
State Uttar Pradesh
Key Dates
Publish Date 19 Nov 2026
Submission Date 15 Dec 2026
Open Date 15 Dec 2026
Finance
Tender Value 37.81 Lakhs
Tender Fee 2354
EMD 76000
Exemption Not Available
Document List
BOQ_2298026.xls
e11548d0-1c41-49f3-8c3c-228a38e99a1c.html
T2_Barabanki.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 19, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 15, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 25 days
Dec 15, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 25 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_2298026.xls

html

e11548d0-1c41-49f3-8c3c-228a38e99a1c.html

pdf

T2_Barabanki.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender