Tender For Dnit For Providing And Installing Of Furniture At Tehsil Complex Nakodar, District Jalandhar
Tender Overview
Project Description
Tender for Dnit For Providing And Installing Of Furniture At Tehsil Complex Nakodar, District Jalandhar , Providing, Supplying And Placing Of Chairseat/Back Assembly: The Cushioned Seat Assembly Consists Of Seat Base Moulded In Glass-Filled Poly-Amide, Moulded Polyurethane Foam & Upholstered With High Stretch Knitted Polyester Fabric. The Back Is Injection Moulded In Glass Filled Polypropylene Which Is Upholstered With Mesh Fabric.The Back Consist Of Adjustable Lumbar Support Made Of Injection Moulded Polypropylene Having An Adjustment Of 3.0 ±0.1 Cm.* Mesh Back Size : 45.5 Cm. (W) X 54.0 Cm. (* Seat Size : 48.5 Cm. (W) X 49.0 Cm. (D)High Resilience (Hr) Polyurethane Foam: The Hr Polyurethane Foam Used In Seat And Backcushion Is Moulded In Density Min 48 Kg/M³, And Hardness Load 15 ± 2 Kgf As Per Is:7888 For 25% Compression.Tilt Mechanism, Spines & Spine Connector: The Seat And Back Are Firmly Connected To The Baseframe And Are Cantilevered In Such A Way That It Gives A Multi-Dimensional Movement Possibility Just With A Simple Lean On The Sides Or Back, Without Need For Complex Manual Adjustments. The Cantilevered Seat Offers Impact Cushioning While Sitting And Synchronises With The Back Movement During Posture Changes. The S Shaped Spines Moulded In High Strength Glass-Filled Poly-Amide And The Spine Connector Moulded In Glass-Filled Poly-Amide Form The Back-Spine Structure Involved In Multi-Dimensional Recline Motion.The Variable Tilt Angle Recline Motion Can Be Adjusted With 3 Position Tilt Limit Feature Which Is Inbuilt In Seat Base And The Tension (Return Force) Is User Weight Dependent.Adjustable Armrests: The Assembly Consists Of Armrest Housing Sliding Over The Armrest Structure,Bothmoulded In Glass-Filled Poly-Amide. The Height Adjustment Feature Is Button Operated Having Adjustment Of6.6±0.5Cm. The Armrest Top Is Made Up Of Integral Skin Pu Moulded Over Plastic Inner Moulded In Glass-Filled Poly-Amide.Pneumatic Height Adjustment: The Seating Height Can Be Adjusted With A Pneumatic Gas-Lift Having An Adjustment Stroke Of 9.2 ± 0.3 Cmpedestal Assembly: The Pedestal Is Injection Moulded In Glass-Filled Poly-Amide And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Is 66.0±0.5 Cm. Pitch Centre Diameter And 76.0±1.0 Cm. With Castors. Twin Wheel Castors: 5 Nos. Twin Wheel Castors Are Injection Moulded In Poly-Amide Having 5.0±0.1Cm Wheel Diameter And Assembled To The Pedestal.Width: 76.0Cm Depth: 76.0Cmheight: 101.0-109.5Cm Seat Height: 44.5-53.8Cmthe Product Should Be Certified By Bifma Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of High Back Chair. Seat/Back Assembly: The Cushioned Seat Assembly Consists Of Seat Base Moulded In Glass-Filled Poly-Amide, Moulded Polyurethane Foam & Upholstered With High Stretch Knitted Polyester Fabric. The Cushioned Back Assembly Consists Of Back Inner Moulded In Polypropylene In-Situ Moulded With Polyurethane Foam & Upholstered With High Stretchknitted Polyester Fabric. Back Size : 45.5 Cm. (/W/) X 53.0 Cm. (H) Seat Size : 48.5 Cm. (W) X 49.0 Cm. (D)High Resilience (Hr) Polyurethane Foam: The Hr Polyurethane Foam Used In Seat And Back Cushion Is Moulded In Density Min 48 Kg/M3, And Hardness Load 15 ± 2 Kgf As Per Is:7888 For 25% Compression.Tilt Mechanism, Spines & Spine Connector: The Seat And Back Are Firmly Connected To The Base Frame And Are Cantilevered In Such A Way That It Gives A Multi-Dimensional Movement Possibility Just With A Simple Lean On The Sides Or Back, Without Need For Complexmanual Adjustments. The Cantilevered Seat Offers Impact Cushioning While Sitting And Synchronises With The Back Movement During Posture Changes. The S Shaped Spines Moulded In High Strength Glass-Filled Poly-Amide And The Spine Connector Moulded In Glass-Filled Poly-Amide Form The Back-Spine Structure Involved In Multi-Dimensional Recline Motion. The Variable Tilt Angle Recline Motion Can Be Adjusted With 3 Position Tilt Limit Feature Which Should Be Inbuilt In Seat Base And The Tension (Return Force) Should Be User Weight Dependent.Adjustable Armrests: The Assembly Consists Of Armrest Housing Sliding Over The Armrest Structure, Both Moulded In Glass-Filled Poly-Amide: The Height Adjustment Feature Should Be Button Operated Having Adjustment Of 6.6±0.5Cm. The Armrest Top Should Be Madeup Of Integral Skin Pu Moulded Over Plastic Inner Moulded In Glass-Filled Poly-Amide.Pneumatic Height Adjustment: The Seating Height Can Be Adjusted With A Pneumatic Gas-Lift Having An Adjustment Stroke Of 9.2 ±0.3 Cm Pedestal Assembly: The Pedestal Should Be Injection Moulded In Glass-Filled Poly-Amide And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Should Be 66.0±0.5 Cm. Pitch Centre Diameter And 76.0±1.0 Cm. With Castors .Twin Wheel Castors :5 Nos. Twin Wheel Castos Are Injection Moulded In Poly-Amide Having 5.0 ± 0.1 Cm Wheel Diamter Assembled To The Pedestal..Overall Dimensions Of Chairseat Height - Min 44.5 To Max 53.8 Cm. Height - Min 99.5 To Max 108.8 Cm.Width& Depth Of Chair As Measured From Pedestal - Width-76.0 Cm And Depth-76.0 Cm. The Product Should Be Certified By Bifma , Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of High Back Chair. Seat/Back Assembly: The Cushioned Seat Assembly Consshould Be Ts Of Seatouter (Material-30% Glass Fiber Nylon)& Upholstered Seat Inner (Material- Poly Propylene) With Moulded Polyurethane Foam &Polyster Fabric. The Net Back Should Be Made Up Of Back Outer (Material-Glass Fiber Filled Nylon)& Back Inner (Material- Pp) And Upholsteredusing Polyester Mesh Fabric With High Tenacity Yarn. Full Back Size: 46.5 Cm. (W) X 60.0 Cm. (H)Seat Size : 51.0 Cm. (W) X 49.0 Cm. (D)High Resilience (Hr) Polyurethane Foam: The Hr Polyurethane Foam Should Be Moulded With Density = 45 +/- 2 Kg/M³ And Hardness Load 12 +/- 2 Kgf For 25% Compression.Back Spine: The Support Spine Should Be Made Up Of High Pressure Die Cast Polished Hedaluminum.Armrests : The Armrest Should Be Having Two Adjustment, Height (6.0±0.5Cm) And Depth (6.0±0.5Cm). Height Adjustment Should Be Provided In Aluminum Structure Of Armrest Which Should Be Connected To Aluminum Back Spine And Should Be Operated By Button. The Depth Adjustment Should Be Provided In Pad Which Should Be Fixed To Armrest Structure. Armrest Top Should Be Made Up Of Pu Molded Over Plastic Inner.Active Bio-Synchro Mechanism:The Adjustable Tilting Mechanism Should Be Designed With The Following Features:360° Revolving Type• Front-Pivot For Tilt With Feet Resting On Ground & Continuous Lumber Support Ensuring More Comfort• Tilt Tension Adjustment Can Be Operated In Seating Position• 5 Position Tilt Limiter Giving Option Of Variable Tilt Angle To The Chair• Seat / Back Tilting Ratio Of 1:2•The Mechanism Housing Should Be Made Uphpdaluminum& Black Powder Coated (Dft 40 To 60 Micron)Seat Depth Adjustment: Seat Depth Adjustment Should Be Integrated In The Seat Through A Sliding Mechanism. Seat Depth Adjustment Range Should Be Of 3.75±0.1 Cmlumbar Support Assembly: The Lumbar Support Assembly Should Consist Of Lumbar Spine (Material-Glass Fiber Filled Nylon) Which Should Be Fixed To Aluminum Back Spine. The Lumbar Pad (Material- Poly Propylene) Should Be Fixed To Lumbar Spine Through Lumbar Pad Support. Lumbar Support Assembly Has Height Adjustment Of 5.0±0.5Cm.Pneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Stroke Of 10.0 ± 0.3Cm.Pad Support. Lumbar Support Assembly Has Height Adjustment Of 5.0±0.5Cm.Pneumatic Height Adjustment: The Pneumatic Height Adjustment Has An Adjustment Stroke Of 10.0 ± 0.3Cm.Pedestal Assembly With Castors:The Pedestal Should Be High Pressure Die Cast Polished Aluminum And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Should Be 65.0 ± 0.5Cm. Pitch-Center Dia.(75.0 ± 1.0Cm. With Castors.)Headrest :The Neckrest Assembly Consshould Be Ts Of Upholstered Neckrest Inner(Material-Polypropylene) With Moulded Polyurethane Foam And Polysterfabric.Upholstered Inner Should Be Fixed To Neckrestcover.Neckrest Should Be Fixed To Back Assembly Through Neckrest Spine .Neckrest Assembly Has Height Adjustment Of 5.5 +/- 0.5Cm And Rotation Adjustment Of Overall 20° +/- 2°.Twin Wheel Castors: The Twin Wheel Castors Should Be Injection Moulded In Black Pp Having 6.0± 0.1Cm Wheel Diameter. Overall Dimensions Of Chairseat Height - Min 45.5 To Max 55.5Cm. Height - Min 95.5 To Max 105.5 Cm.Width& Depth Of Chair As Measured From Pedestal - Width-75.0 Cm And Depth-75.0 Cm The Product Should Be Certified By Bifma , Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of Mid Back Chair. Seat/Back Assembly: The Seat And Back Are Made Up Of 1.2 ±0.1Cm. Thick Hot-Pressed Plywood Measured. Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. The Seat Has Extra Thick Foam On Front Edge To Give Comfort To Popliteal Area.Mid Back Size 47.5 Cm. (W) X 58.0 Cm. (H). Seat Size 47.0 Cm. (W) X 48.0 Cm. (D)High Resilience (Hr) Polyurethane Foam: The Hr Polyurethane Foam Is Moulded With Density = 45±2 Kg/M3 And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression.Armrests: The One-Piece Armrests Are Injection Moulded From Black Co-Polymer Polypropylene. Center Tilt Synchro Mechanism: The Mechanism Is Designed With The Following Features: •360° Revolving Type. • Upight Position Locking • Tilt Tension Adjustmen.•Seat/Back Tilting Ratio Of1:3.Tubular Frame : The Powder Coated ( Dft 40-60 Microns ) Tubular Frame Is Cantilever Type & Made Of Ø 2.54 ±0.03Cm. X 0.2±0.016Cm.Thk. M.S. Er.W. Tube.Pneumatic Height Adjustment : The Pneumatic Height Adjustment Has An Adjustment Stroke Of 12.0 ±0.3Cm.Telescopic Bellow Assembly : The Bellow Is 3-Piece Telescopic Type And Injection Moulded In Black Polypropylene.Pedestal Assembly : The Pedestal Is Injection Moulded In Black 33%Glass-Filled Nylon And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Is 66.3 ±0.5Cm. Pitch-Centre Dia. (76.3 ±1.0Cm With Castors).Win Wheel Castors : The Twin Wheel Castors Are Injection Moulded In Black Nylon.Overall Dimensions Of Chairwidth (W): 76.3 Cm.Depth (D): 76.3 Cm.Height (H): 85.5-97.5 Cm.Seat Height (Sh): 42.5-54.5 Cm.The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of Waiting Chair. Seat Shell :The Seat Shell Should Be A Welded Assembly Of Seat,Back And Side Frame. The Seat And Back Should Be Made Of 0.12±0.013Cm Thk Cr Steel Sheet With Oblong Perforations.They Should Be Welded To Sideframe Of Size 3.2±0.05Cm X 0.5 ± 0.05 Cm Thk Hr Steel.The Welded Assembly Should Be Powder Coated ( Dft 40-60 Microns ).The Seat Has A Front Water Fall Edge Toprovide Popliteal Clearance For Comfortable Seating. It Also Has A Buttock Support Curve That Not Only Provides Rear Support But Also Prevents Small Children From Falling Through The Gap Between Seat And Back. Clean And Flat Surfaces Of Seat And Back Aids In Easy Maintenance. * Seat Size : 47.8 Cm (W) X 44.6 Cm (D) * Back Size : 41.6 Cm (W) X 23.0 Cm (H)Understructure Assembly Consshould Be Ts Of Connecting Beam And Leg Assembly Made Of M.S. E.R.W. Oblong Tube Of Size 7.5±0.03Cm X2.5±0.03Cm X 0.2±0.016Cm Thk.The Welded Structure Assembly Should Be Powder Coated ( Dft 40-60 Microns ).The Leg Assembly Should Be Fitted With Shoes And Levellers In Nylon. The Leg Structure Should Be Designed With Minimal Should Be A Of Contact Close To Groundproviding Easy Access For Cleaning Purposes. The Shoes Fitted To Leg Assembly Help In Aligning The Structure For Back To Back Arrangements. Levellers Take Cshould Be Of Uneven Flooring.Connecting Beam Should Be Fitted With Snap Locking End Cap.Lt Also Aids In Side-By-Side Understructure Alignment, Product Should Be Cerified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of High Back Chair. Seat Assembly: The Seat Is Made Up Of 1.5±0.1 Cm Thick Hot-Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam.Seat Size: 51.8Cm (W) X 49.7Cm (D)Back Assembly: The Back Is Injection Moulded In Glass Filled Polypropylene Which Is 2 Upholstered With Mesh Fabric. The Back Consist Of Adjustable Lumbar Support Made Of Injection Moulded Polypropylene Having An Adjustment Of 5.0 10.1 Cm.Back Size: 47.9 Cm(W) X 66.9 Cm (H)High Resilience (Hr) Polyurethane Foam: The Hr Polyurethane Seat Foam Is Moulded With Density 45+/-2 Kg/M And Hardness 14 ± 2 Kgf As Per Is:7888 For 25% Compression.Armrests (Adjustable):The Height Adjustable Armrest Is Made Of Polypropylene And Can Be Adjusted To 6.010.1Cm Height It Also Has Swivel And To And Fro Adjustment With Moulded Pu Armtopactive Bio-Synchro Mechanism: The Adjustable Tilting Mechanism Is Designed With The Following Features 360° Revolving Typefront-Pivot For Tilt With Feet Resting On Ground & Continuous Lumber Support Ensuring More Comfort Till Tension Adjustment Can Be Operated In Seating Position5 Position Tilt Limitegiving Option Of Variable Sit Angle To The Chair Seat/Back Tilting Ratio Of 1:2The Mechanism Housing Is Made Up Of Hpdc Aluminium& Black Powder Coated (Dft 40 To 60 Micron)Headrest The Headrest Sub-Assembly Is Made Up Of Injection Moulded Glass Filed Polypropylene Which Is Upholstered With Moulded Hr Polyurethane Loam And Fabric Has An Adjustment Of 3.00.1Cm & It Is Assembled Over Greta 20F The Complete Headrest Assembly Is Retro Fic To The Main Chair Pneumatic Height Adjustment: The Pneumatic Height Adjustment With An Adjustment Stroke Of 10.0±0.3Cm.Pedestal Assembly: The Pedestal Is Injection Moulded In Black 30% Glass-Filled Nylon And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Pitch-Center Dia Is 166.1±0.5 Cm.(76.1 ± 1.0 Cm. With Castors).Twin Wheel Castors: The Twin Wheel Castors Are Injection Moulded In Black Polyamide Having 6.01 0.1Cm Wheel Diameter. Width (W) - 76.0Cmdepth (D) - 76.0Cmheight (H) - 114.0 Cm- 123.5Cm Seat Height - 43.5 - 54.0Cmthe Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of Three Seater Sofa. Seat Foam : The Seat Is Made Up Of Pu Foam In Density 28 ±2 Kg/Cu.Mtr With An Additional Top Layer Of Supersoft Pu Foam In Density 32 ± 2 Kg/Cu, Upholstered With Fabric Or Leatherette.Back Foam : The Back Is Made Up Of Pu Foam In Density 28 ± 2 Kg/Cu. Mtr With Two Additional Top Layer Of Supersoft Foam Of Density 32±2 Kg/Cu. Mtr, Upholstered With Fabric Or Leatherette.Understructre : Understructure Is Made Up Of 1.2±0.1 Cm. Thick Hot Pressed Plywood [Moisture Resistance & Termite Proof As Per Is:303] & Pinewood Of Cross Sections Devoid Of Major Knots & Surface Defects. 6 Nos. Per Seat & 3.8Mm Dia Zigzag Spring Assembly Is Mounted Over Understructure For Cushioning Purpose.Leg Assembly : It Is A Welded Assembly Made In Stainless Steel (Grade Ss 202) Tube & Plate With Plastic Endcap. Width (W): 206.0 Cm. Depth (D): 90.5 Cm. Height (H): 85.5 Cm. Seat Height (Sh): 45.0 Cm. The Product Should Be Cerified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Supplying And Placing In Position Main Table,Eru& Pedestal Of The Following Specifications. 2350X2350x750 Primary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Soft Closing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Managementsecondary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top.Modesty Panel Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top.Under Structure Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Integrated Pedestal Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening.Pedestals Are Provided With Lock For Security.The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Supplying And Placing In Position Main Table,Eru& Pedestal Of The Following Specifications. 1800X2100x750 Primary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Soft Closing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Managementsecondary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top.Modesty Panel Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Topunder Structure Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Integrated Pedestal Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Drawer Fronts Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membranepressed On To Toppedestal Construction Is Box-Box-File Type Which Uses Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Is 325 Mm.Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening.Pedestals Are Provided With Lock For Security.The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Supplying And Placing In Position Main Table Of The Following Specifications.1800X900x750 Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With0.4Mm Pvc Membrane Pressed On To Top Softclosing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Management.Modesty Panel Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Topunderstructure Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Integrated Pedestal Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Drawer Fronts Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedstal Construction Is Box-Box-File Type Which Uses Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Is 325 Mm.Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening.Pedestal Is Provided With Lock For Security. The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing & Placing In Position Office Table With With Cpu Hanger With Overall Size Shall Be 1650 Width X 900 Depth X 728 Height Mm . Top Shall Be 18 Mm Thick Pre Laminated Particle Board All Work Surface Edges Shall Be Having Duly Sealed With 2 Mm Thick Pvc Edgebanding.Understructure Modesty Panel 18 Mm Thick Pre Laminated Particle Board . The Rectangular Frame Shall Be Fabricatedcomponent In 1.2 Mm Thick Crca , Finish : Powder Coat( Epoxy Polyster) . Leg Shall Be Fabricated Component In 38 Mm X 25 Mm 1.2Mm Thick Ms Erw Atube ,Finish Powder Coat ( Epoxy Polyster).The Plastic Cap For Cable Travel Shall Be Injection Moulded Polypropylene And Leveler Glide For Shall Be Nylon 6 & Ms Bolt. The Storage Shall Be Having Shell And Drawer Tray 0.6 Mm Thick Crca Finish Powder Coat (Epoxy Polyster) Plus The Drawer Front Shall Be 0.8 Mm Thick Crca Finish Powder Coat (Epoxy Polyster) Plus Lock With 10 Lever Andhandle And Leveller. The Wire Management Shall Be Horizontal Wire Carrier 0.7 Mm Thick Crca Finish Powder Coat (Epoxy Polyster) And Vertical Wire Carrier 0.8 Mm Thick Crca Finish Powder Coat (Epoxy Polyster) .The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Supplying And Placing In Position Main Table,Eru& Pedestal Of The Following Specifications. 1350X600x750 Primary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Soft Closing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Managementsecondary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top.Modesty Panel Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top.Under Structure Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Integrated Pedestal Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirmingdrawer Fronts Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Drawer Fronts Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pedestal Construction Is Box-Box-File Type Which Uses Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Is 325 Mm.Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening.Pedestals Are Provided With Lock For Security.The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Supplying And Placing In Position Main Table Of The Following Specifications.Its Size Shall Be 1650 Width Mm X 900 Depth Mm X 740 Height Mm .Table Top Shall Be 25 Mm Thick Plain Particle Board (Ppb) Clad With 0.6 Mm Thick Post Formed Laminate And 1 Mm Thickbacking Laminate (Bdl) .Flat Edge Duly Sealed With 2 Mm Thick Pvc Beading.The Modesty Shall Be 18 Mm Thick Plain Particle Board ( ) Ppb Clad With 1.0 Mm Thick Decorative Laminate (Dl) On Both Sides. Edge Sealed With 2 Mm Thick Pvc Beading. The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing And Fixing Centre Table Of Size 1200X600 Mm, Glass Table Top And Chrome Plated Pipe Frame, Of Approved Manufacturer, Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of High Back Chair.Seat/Back Assembly: The Cushioned Seat Should Be Made Of Injection Molded Plastic Outer & Inner. Plastic Inner Should Be Upholstered With Stitched Cover And Moulded High Resilience Polyurethane Foam Of Density 45±2 Kg/M3,And Hardness Load 16 ± 2 Kgf For 25% Compression.The Stitched Cover Should Be Made From Spacer Fabric And Leatherette. Cushioned Back Should Be Made Of Pu Foam With Insitu Molded Ms E.R.W Round Tube Of Size 1.9±0.03Cm X 0.16±0.0128Cm. It Upholstered With Spacer Fabric And Leatherette. Seatsize : 47.0Cm.(W)X48.0Cm. (D) .Back Assembly: The Cushioned Back Is Made Of Pu Foam With Insitu Molded Ms E.R.W Round Tube Of Size 1.9±0.03Cm X 0.16±0.0128Cm. It Upholstered With Spacer Fabric And Leatherette. Back Size : 45 Cm. (W) X 75.5 Cm. (D)Armrests : The Armrest Top Should Be Moulded From Polyurethane(Pu) And Mounted On To A Drop Lift Adjustable Type Tubular Armrest Support Made Of 03.81±0.03 Cm X 0.2±0.01 Cm Thk Ms E.R.W Tube. The Armrest Height Adjustable Up To 6.5±0.5Cm In 5 Steps.The Armrest Structure Should Be Powder Coated (Dft 40-60 Micron).Active Bio-Synchro Mechanism : The Adjustable Tilting Mechanism Should Be Designed With The Following Features:•360° Revolving Type.•Front-Pivot For Tilt With Feet Resting On Ground And Continuous Lumbar Support Ensuring More Comfort.• Tilt Tension Adjustment Can Be Operated In Seating Position.•5-Position Tilt Limiter Giving Option Of Variable Tilt Angle To The Chair.• Seat/Back Tilting Ratio Of 1: 2•The Mechanism Housing Should Be Made Up Of Hpdc Aluminium Black Seat Depth Adjustment Seat Depth Adjustment Should Be Integrated In The Seat Through A Sliding Mechanism. Seat Depth Adjustment Range Should Be Of 6.0±0.5 Cm.Adjustable Back Supportback Frame Should Be Connected To The Up/Dn Mechanism Housed In Plastic T Spine. It Can Be Adjusted In The Range Of 7.42±0.5 Cm For The Comfortable Back Support To Suit Individual Need.Pneumatic Ht. Adjustment The Pneumatic Ht Adjustment Has An Adjustment Stroke Of 10.0±0.3 Cm.Pneumatic Ht. Adjustment : The Pedestal Is Injection Moulded In Black 33% Glass-Filled Nylon 66 And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Is 66.1±0.5Cm. Pitch-Center Dia.(76.1±1.0 Cm. With Castors.)Twin Wheel Castor : 5 Nos. Twin Wheel Castors Should Be Injection Moulded In Plastic Having 6.0±0.1Cm Wheel Diameter And Assembled To Pedestal.Overall Dimensions Of Chair Seat Height - 44.4-54.4Cm. Height - 113.6-131.1Cm.Width-76.1 Cm And Depth-76.1 Cmthe Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing, Supplying And Placing Of High Back Chair. Seat/Back Assembly : The Cushioned Seat Should Be Made Of Injection Molded Plastic Outer & Inner. Plastic Inner Should Be Upholstered With Pure Leather And Moulded High Resilience (Hr) Polyurethane Foam Of Density 45±2 Kg/M3,And Hardness Load 16 ± 2 Kgf For 25% Compression.The Cushioned Back Should Be Made Of Pu Foam With Insitu Molded Ms E.R.W Round Tube Of Size 1.9±0.03Cm X 0.16 ±0.0128Cm. It Upholstered With Pure Leather. Woodfenchairseat Size : 47.6 Cm. (W) X 49.2 Cm. (D)Back Size : 47.5 Cm. (W) X 77 Cm. (D)Armrests: The Armrest Top Should Be Moulded From Polyurethane(Pu), Upholstered In Pure Leather And Mounted On To A Drop Lift Adjustable Type Tubular Armrest Support Made Of 03.81±0.03 Cm X 0.2±0.01 Cm Thk M.S E.R.W Tube Having Chrome Plated Finish.The Armrest Height Adjustable Up To 6.5±0.5Cm In 5 Steps.Active Bio-Synchro Mechanism: The Adjustable Tilting Mechanism Should Be Designed With The Following Features:•360° Revolving Type.•Front-Pivot For Tilt With Feet Resting On Ground And Continuous Lumbar Support Ensuring More Comfort.•Tilt Tension Adjustment Can Be Operated In Seating Position.• 5-Position Tilt Limiter Giving Option Of Variable Tilt Angle To The Chair.•Seat/Back Tilting Ratio Of 1: 2•The Mechanism Housing Should Be Made Up Of Hpdcaluminium Black Powder Coated.Seat Depth Adjustment: Seat Depth Adjustment Should Be Integrated In The Seat Through A Sliding Mechanism. Seat Depth Adjustment Range Should Be Of 6.0±0.5 Cm.Adjustable Back Support: Back Frame Should Be Connected To The Up/Dn Mechanism Housed In Plastic T Spine. The Product Should Be Certified By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Almirah With Gordian Lock Shall Have An Overall Size Of 916Mm(W)X486mm(D)X1981mm(H) With Welded Construction. It Should Have The Shelf Thickness Of 0.7 Mm, Back Thickness Of 0.8Mm, Door Thickness Of 0.8Mm (High Yield Strength) And All Other Components Shall Have A Thickness Of 0.9Mm. These Components Shall Be Made Of Crca ‘D Grade High Yield Strength As Per Is:513. The Storwel Plain Shouldhave A Mazak Handle And Three Way Locking Mechanism With Shooting Bolts. It Should Have A Height Wise Adjustable Shelf Mounting Which Shall Have A Uniformly Distributed Load Capacity Of Max 40 Kg. It Should Also Have A M10 Screw Type Leveller With Hex Plastic Base. The Finishing Shall Include Epoxy Powder Coated To The Thickness Of 50 Microns (+/- 10). Plenty Of Colour Options And Shelving Options Shall Be Available. The Product Should Be Certifiied By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Supplying And Placing In Position Conference Table 22 Seaterconfernce Table U Shape Of The Following Specifications .Worksurface : Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Understructure : It Consist Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping.Aluminium Alloy 63400 - Wp Profile Is Used For Connecting Panels Together. The Product Has A Knock-Down Construction.Plastic Abs Access Flap Is Provided For Easy Access To Wires And Cables. Work Top Is Available In Various Shapes As Shown Above.Modestypanel : Made Of 18Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Conforming To Is-12823:1990, Edgebanded With Matching 2 Mm Thick Pvc Lipping. Powder Coated Accent Metal Strip Provided Below Work Surface To Enhance Aesthetics. . The Product Should Be Certifiied By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Supplying And Placing In Position Wooden Visitor Teak Chair Visitor Pu Polished Of Approved Manufacturer . The Product Should Be Certifiied By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , Providing And Fixing Partition Upto Ceiling Height Consisting Of G.I. Frame And Required Board Including Providing And Fixing Of Frame Work Made Of Special Section Power Pressed/ Role Form G.I. Sheet With Zinc Coating Of Grade 175 Consisting Of Floor And Ceiling Channel 50Mm Wide Having Equal Flanges Of 32Mm And 0.5Mm Thick Fixed To The Floor And Ceiling At The Spacing Of 610Mm Centre To Centre With Dash Fastener Of 12.5Mm Diameter,40Mm Length And The Studs 48Mm Wide Having One Flange Of 34Mm And Other Flange 36Mm And 0.50Mm Thick Fixed Vertically Within Flanges Of Floor And Ceiling Channel And Placed At A Spacing Of 610Mm Centre To Centre By 6Mm Dia Bolts And Nuts At Both Ends Of Partition Fixed Flush To Wallwith Rawl Plugs At Spacing 450Mm Centre To Centre And Fixing Of Boards To Either Side Of Frame Work By 25Mm Drive All Screws On Studs Spacing Of 300Mm Centre To Centre, Including Jointing And Finishing To A Flush Finish With Recommended Jointing Compound, Jointing Tape, Joint Finisher And Two Coats Ofprimer Suitable For Board As Per ManufactureS Specificatior And Primer Suitable For Board As Per ManufactureS Specifications And Direction Of Engineer-In-Charge All Complete , Providing And Fixing Blinds Of Approved Manufacturer, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge. , 1. Workstation Partition Made Up Of 45 Mm Thick With 1200Mm Ht. Modular, Panel-Based System With Flexible Construction Allowing For A Variety Of Functional And Decorative Finishes. Material Composed Of Internal Block Of A Pre Lam, Fabric And White Board Tile Above The Worktop. Top Side Panel Glass Tile 4 Mm Thick Toughened Clear Glass, Bottom Plain Metal Tile Made Up Of Pre-Lam Board. All Trims And Profiles Are Made From Aluminium Extrusions For Durability And Sleek Appearance. Worktop Made Up Of 25 Mm Thick Pre-Laminated Particle Board Having Top Surface Decorative Laminate And Bottom Surface Backing Laminate Of Minimum 0.6 Mm Thickness. All Exposed Edges To Be Machine-Pressed With 2 Mm Thick Pvc Edge Banding For Enhanced Durability And Safety. Mounted On Mild Steel (Ms) Legs With Adjustable Levelers. Metal Pedestal (3 Drawer), Keyboard Tray With Mouse Tray, And Metal Cpu Trolley With Castor Wheel.2. Medium Back Chair, Mesh Back, Pu Cushioned Seat, Injection Molded Back Frame, Pu Adjustable Arms, Synchro Tilt Mechanism, Powder Coated, Class 4 Gas Lift And Nylon Base With 60 Mm Castors, Complete In All Respect.3. Reading Table - 2350 X 1150 X 750 Mm. Worktop Made Up Of 25 Mm Thick Mdf With One Side Pre-Laminated Board. Understructure Made Up Of 18 Mm Thick Pre-Laminated Twin Board With All Exposed Edges Edge-Banded With 2 Mm Pvc Lipping. Wire Management Wire Raiser And Cable Tray Made Of 0.8 Mm Crca Sheet Duly Powder Coated With Two Cable Cut-Outs Beneath The Access Flap. . The Product Should Be Certifiied By Bifma, Complete As Per Specifications And To The Entire Satisfaction Of Engineer In Charge.
BOQ
| Sl. No. | Item Description |
| 1 | Providing, supplying and placing of ChairSEAT/BACK ASSEMBLY: The cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The Back is injection moulded in glass filled Polypropylene which is upholstered with Mesh fabric.The back consist of adjustable lumbar support made of injection moulded Polypropylene having an adjustment of 3.0 ±0.1 cm.* Mesh Back Size : 45.5 cm. (W) x 54.0 cm. (* Seat Size : 48.5 cm. (W) x 49.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam used in seat and backcushion is moulded in Density Min 48 kg/m³, and hardness load 15 ± 2 kgf as per IS:7888 for 25% compression.TILT MECHANISM, SPINES & SPINE CONNECTOR: The seat and back are firmly connected to the baseframe and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The \\"S\\" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-amide form the back-spine structure involved in multi-dimensional recline motion.The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent.ADJUSTABLE ARMRESTS: The assembly consists of armrest housing sliding over the armrest structure,bothmoulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide.PNEUMATIC HEIGHT ADJUSTMENT: The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cmPEDESTAL ASSEMBLY: The pedestal is injection moulded in glass-filled Poly-amide and fitted with 5 nos. twin wheel castors. The pedestal is 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors. TWIN WHEEL CASTORS: 5 nos. twin wheel castors are injection moulded in Poly-amide having 5.0±0.1cm wheel diameter and assembled to the pedestal.Width: 76.0cm Depth: 76.0cmHeight: 101.0-109.5cm Seat Height: 44.5-53.8cmThe product should be certified by BIFMA complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 2 | Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretchknitted polyester fabric. Back Size : 45.5 cm. (/W/) x 53.0 cm. (H) Seat Size : 48.5 cm. (W) x 49.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam used in seat and back cushion is moulded in Density Min 48 kg/m3, and hardness load 15 ± 2 kgf as per IS:7888 for 25% compression.TILT MECHANISM, SPINES & SPINE CONNECTOR: The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complexmanual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The \\"S\\" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-amide form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which should be inbuilt in seat base and the tension (return force) should be user weight dependent.ADJUSTABLE ARMRESTS: The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide: The height adjustment feature should be button operated having adjustment of 6.6±0.5cm. The Armrest Top should be madeup of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide.PNEUMATIC HEIGHT ADJUSTMENT: The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ±0.3 cm PEDESTAL ASSEMBLY: The pedestal should be injection moulded in glass-filled Poly-amide and fitted with 5 nos. twin wheel castors. The pedestal should be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors .TWIN WHEEL CASTORS :5 nos. twin wheel castos are injection moulded in Poly-amide having 5.0 ± 0.1 cm wheel diamter assembled to the pedestal..Overall Dimensions of ChairSeat Height - min 44.5 to max 53.8 cm. Height - min 99.5 to max 108.8 cm.Width& Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm. The product should be certified by BIFMA , complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 3 | Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seatouter (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam &polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholsteredusing Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H)Seat Size : 51.0 cm. (W) x 49.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression.BACK SPINE: The support spine should be made up of High Pressure Die cast polished hedAluminum.ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism:The adjustable tilting mechanism should be designed with the following features:360° revolving type• Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort• Tilt tension adjustment can be operated in seating position• 5 position Tilt limiter giving option of variable tilt angle to the chair• Seat / back tilting ratio of 1:2•The mechanism housing should be made upHPDAluminum& black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cmLUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)Headrest :The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polysterfabric.Upholstered inner should be fixed to Neckrestcover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2°.TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. Overall Dimensions of ChairSeat Height - min 45.5 to max 55.5cm. Height - min 95.5 to max 105.5 cm.Width& Depth of Chair as measured from pedestal - Width-75.0 cm and Depth-75.0 cm The product should be certified by BIFMA , complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 4 | Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area.MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM: The mechanism is designed with the following features: •360° revolving type. • Upight position locking • Tilt tension adjustmen.•Seat/back tilting ratio of1:3.TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2±0.016cm.thk. M.S. ER.W. Tube.PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors).WIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.Overall Dimensions of ChairWIDTH (W): 76.3 CM.DEPTH (D): 76.3 CM.HEIGHT (H): 85.5-97.5 CM.SEAT HEIGHT (SH): 42.5-54.5 CM.The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 5 | Providing, supplying and placing of waiting chair. SEAT SHELL :The seat shell should be a welded assembly of seat,back and side frame. The seat and back should be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powder coated ( DFT 40-60 microns ).The seat has a front water fall edge toprovide popliteal clearance for comfortable seating. It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back aids in easy maintenance. * SEAT SIZE : 47.8 cm (W) x 44.6 cm (D) * BACK SIZE : 41.6 cm (W) x 23.0 cm (H)Understructure assembly consshould be ts of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5±0.03cm x2.5±0.03cm x 0.2±0.016cm thk.The welded structure assembly should be powder coated ( DFT 40-60 microns ).The leg assembly should be fitted with shoes and levellers in Nylon. The leg structure should be designed with minimal should be a of contact close to groundproviding easy access for cleaning purposes. The shoes fitted to leg assembly help in aligning the structure for back to back arrangements. Levellers take cshould be of uneven flooring.Connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment, product should be cerified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 6 | Providing, supplying and placing of High Back Chair. SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood upholstered with fabric and moulded polyurethane foam.SEAT SIZE: 51.8cm (W) x 49.7cm (D)BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm.BACK SIZE: 47.9 cm(W) x 66.9 cm (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU armtopACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features 360° revolving typeFront-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort Till tension adjustment can be operated in seating position5 position Tilt limitegiving option of variable sit angle to the chair Seat/back tilting ratio of 1:2The mechanism housing is made up of HPDC Aluminium& black powder coated (DFT 40 to 60 micron)HEADREST The Headrest sub-assembly is made up of injection moulded glass filed Polypropylene which is upholstered with moulded HR polyurethane loam and fabric has an adjustment of 3.00.1cm & it is assembled over GRETA 20F The complete headrest assembly is retro fic to the main chair PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0±0.3cm.PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 166.1±0.5 cm.(76.1 ± 1.0 cm. with castors).TWIN WHEEL CASTORS: The twin wheel castors are Injection moulded in black Polyamide having 6.01 0.1cm wheel Diameter. WIDTH (W) - 76.0cmDEPTH (D) - 76.0cmHEIGHT (H) - 114.0 cm- 123.5cm SEAT HEIGHT - 43.5 - 54.0cmThe product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 7 | Providing, supplying and placing of three seater sofa. SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette.BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose.LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM. The product should be cerified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 8 | Supplying and placing in position Main Table,ERU& pedestal of the following specifications. 2350x2350x750 Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire managementSecondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Pedestals are provided with lock for security.The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 9 | Supplying and placing in position Main Table,ERU& pedestal of the following specifications. 1800x2100x750 Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire managementSecondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to topUnder structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membranepressed on to topPedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Pedestals are provided with lock for security.The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 10 | Supplying and placing in position Main table of the following specifications.1800x900x750 Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to topUnderstructure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Pedestal is provided with lock for security. The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 11 | Providing & placing in position office table with with CPU Hanger with overall size shall be 1650 Width x 900 Depth x 728 Height mm . Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding.Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricatedcomponent in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever andhandle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) .The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 12 | Supplying and placing in position Main Table,ERU& pedestal of the following specifications. 1350x600x750 Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire managementSecondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirmingDrawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Pedestals are provided with lock for security.The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 13 | Supplying and placing in position Main table of the following specifications.Its size shall be 1650 Width mm x 900 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thickbacking laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 14 | Providing and Fixing Centre table of size 1200x600 mm, Glass table top and chrome plated pipe frame, of approved manufacturer, certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 15 | Providing, supplying and placing of High Back Chair.SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16±0.0128cm. It upholstered with spacer fabric and leatherette. SeatSIZE : 47.0cm.(W)x48.0cm. (D) .BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16±0.0128cm. It upholstered with spacer fabric and leatherette. BACK SIZE : 45 cm. (W) x 75.5 cm. (D)ARMRESTS : The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5±0.5cm in 5 steps.The Armrest structure should be powder coated (DFT 40-60 micron).ACTIVE BIO-SYNCHRO mechanism : The adjustable tilting mechanism should be designed with the following features:•360° revolving type.•Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.• Tilt tension adjustment can be operated in seating position.•5-position Tilt limiter giving option of variable tilt angle to the chair.• Seat/back tilting ratio of 1: 2•The mechanism housing should be made up of HPDC Aluminium black SEAT DEPTH ADJUSTMENT Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm.ADJUSTABLE BACK SUPPORTBack Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need.PNEUMATIC HT. ADJUSTMENT The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.PNEUMATIC HT. ADJUSTMENT : The pedestal is injection moulded in black 33% glass-filled Nylon 66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.1±0.5cm. pitch-center dia.(76.1±1.0 cm. With castors.)TWIN WHEEL CASTOR : 5 Nos. twin wheel castors should be injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal.Overall Dimensions of Chair Seat Height - 44.4-54.4cm. Height - 113.6-131.1cm.Width-76.1 cm and Depth-76.1 cmThe product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 16 | Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. WoodfenchairSeat SIZE : 47.6 cm. (W) x 49.2 cm. (D)BACK SIZE : 47.5 cm. (W) x 77 cm. (D)ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps.ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features:•360° revolving type.•Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.•Tilt tension adjustment can be operated in seating position.• 5-position Tilt limiter giving option of variable tilt angle to the chair.•Seat/back tilting ratio of 1: 2•The mechanism housing should be made up of HPDCAluminium black powder coated.SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm.ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. The product should be certified by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 17 | Almirah with gordian lock shall have an overall size of 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain shouldhave a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. The product should be certifiied by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 18 | Supplying and placing in position conference table 22 seaterconfernce table U shape of the following specifications .Worksurface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Understructure : It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above.ModestyPanel : Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edgebanded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. . The product should be certifiied by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 19 | Supplying and placing in position wooden visitor Teak chair visitor pu polished of approved manufacturer . The product should be certifiied by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 20 | Providing and fixing partition upto ceiling height consisting of G.I. frame and required board including providing and fixing of frame work made of special section power pressed/ role form G.I. sheet with zinc coating of grade 175 consisting of floor and ceiling channel 50mm wide having equal flanges of 32mm and 0.5mm thick fixed to the floor and ceiling at the spacing of 610mm centre to centre with dash fastener of 12.5mm diameter,40mm length and the studs 48mm wide having one flange of 34mm and other flange 36mm and 0.50mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6mm dia bolts and nuts at both ends of partition fixed flush to wallwith rawl plugs at spacing 450mm centre to centre and fixing of boards to either side of frame work by 25mm drive all screws on studs spacing of 300mm centre to centre, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, joint finisher and two coats ofprimer suitable for board as per manufacture’s specificatior and primer suitable for board as per manufacture’s specifications and direction of engineer-in-charge all complete |
| 21 | Providing and fixing Blinds of approved manufacturer, complete as per specifications and to the entire satisfaction of Engineer in Charge. |
| 22 | 1. Workstation partition made up of 45 mm thick with 1200mm Ht. Modular, panel-based system with flexible construction allowing for a variety of functional and decorative finishes. Material composed of internal block of a Pre lam, fabric and white board tile above the worktop. Top side panel glass tile 4 mm thick toughened clear glass, Bottom plain metal tile made up of pre-lam board. All trims and profiles are made from aluminium extrusions for durability and sleek appearance. Worktop made up of 25 mm thick pre-laminated particle board having top surface Decorative laminate and bottom surface Backing laminate of minimum 0.6 mm thickness. All exposed edges to be machine-pressed with 2 mm thick PVC edge banding for enhanced durability and safety. Mounted on mild steel (MS) legs with adjustable levelers. Metal pedestal (3 drawer), keyboard tray with mouse tray, and metal CPU trolley with castor wheel.2. Medium back chair, mesh back, PU cushioned seat, injection molded back frame, PU adjustable arms, synchro tilt mechanism, powder coated, class 4 gas lift and nylon base with 60 mm castors, complete in all respect.3. Reading Table – 2350 x 1150 x 750 mm. Worktop made up of 25 mm thick MDF with one side pre-laminated board. Understructure made up of 18 mm thick pre-laminated twin board with all exposed edges edge-banded with 2 mm PVC lipping. Wire management wire raiser and cable tray made of 0.8 mm CRCA sheet duly powder coated with two cable cut-outs beneath the access flap. . The product should be certifiied by BIFMA, complete as per specifications and to the entire satisfaction of Engineer in Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
TodayBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender