Civil Aviation Boards / Undertakings / PSU Closing in 12 days TDR #58603072

Tender For Construction Of New Domestic Terminal Building And Miscellaneous Works At Hubballi Airport. Sh - Additional Civil Works

Issued by Boards / Undertakings / PSU · Dharwad, Karnataka
Tender Value
1.97 Crore
Estimated cost
Bid Submission
01 Dec 2026
12 days left
EMD
5.93 Lakhs
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Dharwad → Karnataka
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Construction Of New Domestic Terminal Building And Miscellaneous Works At Hubballi Airport. Sh - Additional Civil Works

BOQ

Name of Work:- Construction of new domestic terminal building and miscellaneous works at Hubballi airport. SH - Additional Civil Works
Sl. No. Item Description
1Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 3000 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil
2Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
3Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-I) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
4Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: All works upto plinth level. Concrete of M30 grade with cement content of 350 kg /cum and Admix -0.5 % (Mix design shall be provided by AAI without any cost deduction)
5Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: All works above plinth level. Concrete of M30 grade with cement content of 350 kg /cum and Admix -0.5 % (Mix design shall be provided by AAI without any cost deduction)
6Add for using extra cement in the items of design mix over and above the specified cement content therein.
7Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
8Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers
9Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts
10Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
11Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.a) Thermo-Mechanically Treated bars of grade Fe-500D or more.
12Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required: In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
1312 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)
14Painting with synthetic enamel paint of approved brand and manufacture to give an even shade a) Two or more coats on new work
15Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
16Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
17Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron)
18Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion. For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
19Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.
20Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm).
21Providing and laying non-pressure NP3 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe
22Brick work with Fly Ash bricks of class designation 7.5 in superstructure below plinth level in all shapes and sizes in: Cement mortar Cement mortar 1:6 (1 Cement : 6 coarse sand)
23Brick work with Fly Ash bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 (1 Cement : 6 coarse sand)
24Providing and laying tactile tile of stainles steel strips (SS 316, for vision impaired persons as per standards) of size 280x35x4.5 mm drilled fixed tight with inbuilt stem/shank including fixing with approved epoxy compound etc., of required size, on the top of the floor with suitable arrangement as per approval of Engineer-in-charge.
25Providing and laying tactile tile of stainles steel stud (SS 316, for vision impaired persons as per standards) of size 35x25x4.5 mm drilled fixed tight with inbuilt stem/shank including fixing with approved epoxy compound etc., of required size, on the top of the floor with suitable arrangement as per approval of Engineer-in-charge.
26Providing & Fixing Frosted film (300 micron thick) for glass, as per direction of Engineer in charge.
27Supply & Installation of SS Bollard as per approved make of Stainless Steel 304 grade Bollard , Height-900mm, Diameter – 100mm, thickness of bollard -2mm , Base plate dia –140 mm, Fixed to floor with Chemical fasteners as per refer drawing and technical specifications complete with all respect as desired and direction of Engineer in charge.
28Supply and delivery at site of 9-Litre capacity round/cylindrical Stainless Steel (SS-304) Pedal Trash Bin, completely assembled and packed. The outer body shall be fabricated from premium, corrosion-resistant stainless steel featuring a brushed/matte finish with an anti-fingerprint coating. The unit must incorporate a heavy-duty, hands-free foot pedal mechanism integrated with a soft-close/silent-close lid system. The supply must include a removable, leak-proof inner plastic bucket equipped with a robust integrated handle. Rates shall be inclusive of the complete bin assembly, manufacturer's warranty, protective packaging, loading, transit and safe transport/unloading at the designated site store, complete as per the technical specifications and instructions of the Engineer-in-Charge. (Make- Tramontina or equivalent)
29Providing and fixing wind clamp of extruded Aluminium (Alloy 6061) section as per required size, drawing and specification including Stainless steel (316 grade) nut bolts with fastner on Double insulated aluminium standing seam steel roofing System as per direction of Engineer in charge
30Hiring and running charges of hydraulic excavtor 3D including driver and fuel for misc. works etc as per direction of Engineering in charge
31Providing and applying tack coat using bitumen emulsion (Rapid setting) complying with IS:8887, spraying the bitumen with mechanically operated spray unit at the rate specified below, cleaning and preparing the existing pavement surface as per specifications complete in all respects as per direction of Engineer-In-Charge. If the actual quantity of bitumen emulsion varies from the quantity specified, necessary cost adjustment for deviation in the quantity of bitumen emulsion shall be done as per rate in actual supply voucher from nearest refinery at the time of execution. a) 0.20 Kg/Sqm on existing bituminous surface
32Providing and laying of Hot Mix Semi Dense Asphaltic Concrete (SDAC) using crushed stone aggregate of quality, size and grading as specified and 2% cement by weight of aggregates as filler of quality as specified and Viscosity Grade Bitumen (Supplied in Bulk) in proportions as per job mix formula and laid to specified levels, grade and camber as per specification, drawings and as directed by the Engineers-in-charge including compacting with 8-10 tonne, preferably vibratory road roller of adequate capacity to achieve the specified values of compaction, strength, surface accuracy complete [for tendering purpose VG bitumen of grade VG-30 content shall be taken as 123.76 kg/m3 of mix supplied in bulk produced by Govt. Refineries and 2% cement by weight of aggregates as filler Material]. (Job Mix formula shall be provided by AAI without any cost deduction) Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58603072
AUTHORITY Boards / Undertakings / PSU
TENDER VALUE 1.97 Crore
LAST DATE 01-12-2026
Authority
Authority Name Airports Authority Of India
Work Description Tender for Construction Of New Domestic Terminal Building And Miscellaneous Works At Hubballi Airport. Sh - Additional Civil Works
Basic Detail
Tender No AAI/Hub/Engg (C)/NTB-ACW/2026-27
Bidding Type Tender
Location
City Dharwad
State Karnataka
Key Dates
Publish Date 18 Nov 2026
Submission Date 01 Dec 2026
Open Date 02 Dec 2026
Finance
Tender Value 1.97 Crore
Tender Fee 1180
EMD 5.93 Lakhs
Exemption Not Available
Document List
BOQ_347421.xls
d7e7a878-5029-4f16-9deb-e6ae699e0b0f.html
TenderDocument.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 18, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 01, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 12 days
Dec 02, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 13 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_347421.xls

html

d7e7a878-5029-4f16-9deb-e6ae699e0b0f.html

pdf

TenderDocument.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender