Tender For Repair And Maintenance Of 90 Cm Aia Double Vent Hume Pipe Sluice Gate (21.837729N, 88.199387E) At Prasadpur Near The House Of Triptipada Das In Mouza- Kakdwip, G.P.- Swami Vivekananda, Block- Kakdwip Under Kakdwip-I Sub-Division Of Ced-Ii,
Tender Overview
Project Description
Tender for Repair And Maintenance Of 90 Cm Aia Double Vent Hume Pipe Sluice Gate (21.837729N, 88.199387E) At Prasadpur Near The House Of Triptipada Das In Mouza- Kakdwip, G.P.- Swami Vivekananda, Block- Kakdwip Under Kakdwip-I Sub-Division Of Ced-Ii, Sdb.
BOQ
| Sl. No. | Item Description |
| 1 | PART A as per DSR 2023 |
| 2 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge In cement mortar |
| 3 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (including equivalentdesign mix) |
| 4 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 5 | 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form work for :Foundations, footings, bases for columns |
| 8 | Applying Correction factor on DSR 2023 on account on account of GST @ 0.973[for PART-A, Sl no.1to sl no.6) |
| 9 | Applying Cost Indices @ (118/100)=1.18(for PART-A) |
| 10 | PART - BTaking out sluice gate draw shutter gearing arrangements & pedestal including refitting the same with new nuts & bolts where necessary.(a) Upto 4 Sqm.(ii) Taking out only. |
| 11 | Taking out flap shutter of sluice gate including hoisting arrangements and refitting the same with new nuts & bolts where necessary(a) Upto 4 Sqm.(i) Taking out and refitting the same. |
| 12 | (ii) Taking out only. |
| 13 | Supplying, fitting, fixing Mild Steel draw shutter with Mild Steel plate of thickness as specified by the Engineer-in-charge and other necessary Mild Steel sections for sluice including fabricating the same (as per drawing and instruction given by the Engineerin-charge) excluding cost of Mild Steel guide channel, sill beam, gearing arrangement etc. but including painting with two coats of anticorrosive bituminous paint of approved make & brand over two coat of red lead primer and with necessary masonry work with all materials supply etc. complete at site. |
| 14 | Supplying, fitting and fixing at site Cast Iron flap shutter for hume pipe sluice with Cast Iron collar and other fittings etc. complete (as per drawing & direction of Engineer-in charge) including casting the same, necessary drilling & painting with two coats of anticorrosive bituminous paint of approved make and brand over two coats of red lead primer with carriage to site complete.(This Rate is inclusive of taking out of old ones) |
| 15 | Supplying, fitting & fixing Cast Iron wheel (after taking out existing one if necessary), rim made of 28 mm. to 36 mm. dia to fit any size of gear rod including carriage to site, painting with two coats of bituminous paint over two coats of red lead primer etc. complete as per direction of the Engineer-in-charge.(b) 60 cm. dia. Cast Iron wheel |
| 16 | Supplying / Replacing Gun Metal Bush for screw gearing arrangement required for hanging arrangement of draw shutter and fitting & fixing with the screw gearing arrangement for operating the draw shutter by taking out the old screw gearing arrangement and Gun Metal bush etc. complete as per direction of the Engineer-in-charge. (The old materials to be returned to Departmental Godown.)(a) 50 mm. dia |
| 17 | Supplying / Replacing Gear rod by a new Mild Steel Gear rod, threaded length as required and fitting, fixing in position with screw gearing arrangement for operating the draw shutter including taking out old gear rod by cutting bolts etc. complete as per direction of the Engineer-in-charge. (The old materials to be returned to Departmental Godown.)(a) 50 mm. dia |
| 18 | Supplying, fitting & fixing in position rubber seal arrangements with musical note harmonic 'J' type for making water tight in both up and down stream of draw shutter as well as flap shutter including guide paths, additional M. S. flats, bolts and nuts for fixing the rubber seal in position including fabrication cost and carriage of all materials to site and complete as per direction of the Engineer-incharge(b) Musical Note, Harmonic Type(i) 59 mm x 6 mm |
| 19 | Supplying, fitting & fixing in position rubber seal arrangements with musical note harmonic 'J' type for making water tight in both up and down stream of draw shutter as well as flap shutter including guide paths, additional M. S. flats, bolts and nuts for fixing the rubber seal in position including fabrication cost and carriage of all materials to site and complete as per direction of the Engineer-incharge(b) Musical Note, Harmonic Type (b) 127 mm. x 6 mm. |
| 20 | Supplying / Replacing at site new pedestal or other similar items for sluices made with Mild Steel plates, angles, channels, holding down nuts & bolts etc. including fitting, fixing in position in concrete or masonry complete as per direction of the Engineer - in -charge. |
| 21 | Supplying / Replacing including fitting & fixing at site new Cast Iron guide channel true to the line & level for draw shutters of sluices as per drawing & direction of the Engineer-in-charge with Cast Iron hold fast not more than 1 Metre apart including two coats of anti-corrossive bituminous paint of approved make and brand over two coats of red lead primer. (Rate is inclusive of taking out of old guide channels, if required) |
| 22 | Labour charges for collecting or taking out displaced cement concrete or brick blocks of all sizes from slope, bed or apron and relaying the same in canal bed or slopes including clearing, dressing, ramming and preparing bed with necessary earthwork complete within a lead of 200 metre and all lifts complete. |
| 23 | Making filter with well graded 40 mm down ballasts and laying uniformly behind weep holes, below pitching on bed, side slopes including supply and carriage of all materials to site including preparing bed with earthwork up to 30 cm depth, where necessary and compacting with wooden malllet after laying to achieve designed section as per direction of the Engineer- in - Charge (measurements will be on finished work / in stack after deducting necessary void).(a) Jhama ballast |
| 24 | Cast in situ Brick block pitching of required size with 1st class kiln burnt / picked jhama bricks in cement mortar including flush pointing on all faces except exposed face which will be plastered with 19 m.m. thick cement plaster & curing, dressing, ramming & preparing subgrade in slopes & bed with all leads & lifts including cost of all materials. The gap between adjacent blocks will not be more than 10 m.m. (Mortar mix for making blocks, pointing & plastering-1:4) |
| 25 | Supplying, dressing and stacking at site bamboo pins above 5 cm. diameter and upto 7.5 cm. diameter. (Dia. to be measured at mid length). |
| 26 | Driving bamboo pins in standing or flowing water including scaffolding and driving appliances.(a) Where boats are not necessary. |
| 27 | Supplying, fitting and fixing with iron nails half split bamboo wailing pieces (av. dia. of bamboo not less than 5.0 cm.) |
| 28 | Supplying Eucalyptus-bullah piles at work site, including dressing and making one end pointed.(iii) 15 cm diameter |
| 29 | Labour for driving Jhaw / Eucalyptus bullah piles by monkey in all sorts of soil including hoisting and placing piles in position, protecting the pile head with iron ring and cutting and shaping heads before and after driving and including hire and labour for necessary driving appliances and all tackles.(iii) 15 cm diameter |
| 30 | Supplying, fitting and fixing with iron nails half split bullah wailing pieces and cross pieces etc. complete with cost of all materials and carriage to site.(a) Width of thinner end above 10 cm.and less than 15cm(i) Jhaw / Eucalyptus. |
| 31 | Coal tarring on wooden surfaces including cost of materialsa) One Coat |
| 32 | Supplying empty Cement bags in good condition |
| 33 | Filling empty Cement bags with dry earth or sand, stitching the bag (cost of thread included) and carrying and placing them in position and all incidental charges complete but excluding cost of filling materials, (Earth or sand) and gunny bags. |
| 34 | Earthwork in making new embankment / ring bundh/ retired embankment by excavation of earth from borrow pits in all kinds of soil including making berms and depositing the same in layers not exceeding 25 cm. as per profile within an initial lead of 30 metre and lift of 1.5 metre including cost of nicking outlines, dug-belling, putting profiles, cutting and removing thick and thorny jungles, uprooting trees and stumps of all sizes upto 30 cm., girth from the site alignment as per direction of the Engineer-in- Charge including dewatering, removal of weeds, carcasses, organic matter etc., if any, breaking clods, rough dressing, watering, ramming, compacting etc. complete.A. Where land for earth owned/arranged by the Department. |
| 35 | Extra rate over Item Nos.31 for all kinds of soil for every additional lead of 30 metres or part thereof beyond the initial lead of 30 metres.. a) One extra lead. |
| 36 | Extra rate over Item Nos.31 for all kinds of soil for every additional lift of 1.50 metre or part thereof beyond the initial lift of 1.50 metre. |
| 37 | Earthwork in excavation in all kinds of soil for making embankments, repairs to the embankment, closing breaches etc. as per profile including supply and transporting the earth by truck or tractor or any other mechanical means on land , including loading, transporting, unloading and stacking with all lifts bothways and head load where necessary and depositing the same on embankments, clannels, filling depressions in requisite profile, levelling as per direction of the Engineer-in-charge within a lead of,A) Beyond 500 metre and upto 1.00 km |
| 38 | Earthwork in re-excavation / silt clearance of drainage channels in all kinds of soil including sludge and slush but excluding slush mixed with industrial wastes, sewage, municipal garbage, carcasses, etc and depositing the same as per profile in proper place as directed by the Engineer-in-charge without causing hindrance to traffic and posing health hazard and making arrangement to maintain the site in workable condition including removal of polypacks, brickbats, stone ballasts & boulders, remnants of bullah & bamboo pins and all kinds of water hyacinth, solid / semi solid compact mass formed due to water hyacinth and burning them to ashes or removing outside Govt land where necessary and removal of thick & thorny jungles upto 30 cm girth including shoring and shuttering, if required, and including initial removal of sludge and slush etc by pan or bucket if required, and making arrangement for bailing out of any seepage water and removal of sand or soil blown from underneath, all complete.(a) By manual means within an initial lead of 30 M and an initial lift of 1.50 M(Measurement : Pre-work and Post-work level section. Pre-work section to be taken after removal of water hyacinth and all other floating materials etc.)(a) By manual means within an initial lead of 30 M and an initial lift of 1.50 M |
| 39 | Add 18% for GST [ for PART-B, Sl no.9 to sl no.36] |
| 40 | Add 1% Cess [ for PART-B, Sl no.9 to sl no.37] Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender