Tender For Under District Jaunpur, Beautification Of Dr. B.R. Ambedkar Statue In Abbopur, Block Shahganj Gram Panchayat, Lot No 22
Tender Value
10 Lakhs
Estimated cost
Bid Submission
26 Nov 2026
5 days left
EMD
20000
Bank guarantee accepted
Document Fee
856
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaunpur → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Under District Jaunpur, Beautification Of Dr. B.R. Ambedkar Statue In Abbopur, Block Shahganj Gram Panchayat, Lot No 22
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil as per SI.No. 2.8.1 |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) As per SI no. 4.1.8 |
| 3 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) as SI No-5.1.2 |
| 4 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) as SI No-5.1.2 |
| 5 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Above Plinth Lvl as SI No-5.2.2 |
| 6 | Steel reinforcement for R.C.C. work ready to use \\"cut and bend\\" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. As per SI. No.- 5.22 B.1 |
| 7 | Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. In grantings, frames, guard bar, ladder, railing, brackets, gates and similar works as per SI no. 10.25.2 |
| 8 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing andpolishing etc. all complete as specified and as directed by the Engineer-in-Charge.DSR 11.56.1 |
| 9 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil as per SI.No. 2.8.1 |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) As per SI no. 4.1.8 |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). D.S.R. CODE. 4.1.3 |
| 12 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire D.S.R. CODE 16.18.1 |
| 13 | Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. |
| 14 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture D.S.R. CODE 13.48.3 |
| 15 | Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3 |
| 16 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 |
| 17 | Providing & laying in position cement concrete in 1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) D.S.R. (2023) CODE. 4.1.11 |
| 18 | Brick masonry work in 1:4 cement mortar in foundation complete excluding pointing and plastering, as per drawing and Technical Specification Clauses 600, 1202 & 1203. MoRD Spec. 600 & 1200 II Chapter 11 SI.No. 11.5 (2) |
| 19 | Construction of granular sub-base by providing well graded material , spreading in uniform layers with motor grader on prepared surface ,mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achive the desired density, complete as per Technical Specification Clause. 401. |
| 20 | Providing and Laying of interlocking concrete block pavement having thickness 80 mm as per drawings and technical specification clause .MoRD Spec. 1504 Chapter 6 SI.No. 6.7 |
| 21 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement as per SI No-11.20.1 |
| 22 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). D.S.R. CODE. 4.1.3 |
| 23 | Supply and Installation of Solar street light . PV ModuleBROAD PERFORMANCE PARAMETERSOnly indigenous modules shall be used in the project. SPV module of 36 cells 110 Wp, Voltage at Maximum Power (Vmpp) 18.0 V±0.3%. Module Voc should be minimum of 22 V. Module efficiency should be > 14.8%BatteryLithium Ferro Phosphate (LifePO4/LFP) 12.8 Volt, 45 Ah, at STCLight SourceWhite Light Emitting Diode (W-LED) 18 Watt (LED +Driver) Using LEDs which emits ultraviolet light will not be permittedLight Out putWhite colour (colour temperature 5500-6500 K). The Lumen efficacy of LED-minimum 135 lumens/Watt and the lumens output (luminous flux) of luminaries should be 2250 lumen. The illumination should be uniform without dark bands or abrupt variations, and soothing to the eye. Higher light output will be preferred.Mounting of light, Controller and Battery packApprox., 4.5 meter above the ground, mounted at pole below the module mounting structure.Average duty cycleDusk to dawn |
| 24 | lksyj gkbZekLV ykbZfVax la;a=] lksyj ihoh iSuy] cSVjh cSad& yhfFk;e Qsjk&QkLQsV {kerk 12-8 oksYV 50 ,Eeh;j vkoj (4x50 ,Eih;j vkoj okV½ Y;wfeukj& g~okbZV ,ybZMh vk/kkfjr 72 okV (4x18 okV {kerk½ M~;wVh lkbZfdy&lk;adky ls izkRk% dky rd vkDVkxksuy iksy& thvkbZ 7 ehVj yEckbZ] vU; vo;o& dfcy] cSVjh ckDl ,oa vU; gkMZ os;j ¼vuqca/kkuqlkj½ |
| 25 | Supply and Installation of Cement Bench(M.R.) |
| 26 | Plantation work (With Ashoka Tree) |
| 27 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete D.S.R. 10.1 |
| 28 | Providing & Fixing of plastic net as tree guard |
| 29 | Supply and fixing of informatory M.S sign board, size 1.2X0.90m made of 18mm gauge M.S sheet fic in ISA 40X40X6mm, frame support in back side by 40X5mm flat iron on all four side along with to vertical post of2.90mt. Diagonal bracing of size 40x5mm fiat iron, electrically welded and painted with one coat red oxide primer and 2 coat superier quality enamel paint with lettering work of required specified information also I/c fixing in trench both side C.C. 1:2:4 size 0.45 x 0.45x0.50 m Required for proper complation of the work. Reference Specification S.I. No. 502 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender