Civil Aviation Boards / Undertakings / PSU Closing in 18 days TDR #58593470

Tender For Improvisation Of Traffic Lane In Front Of Terminal Building At S.V. Airport, Raipur. Sh : Provision Of Drainage System And Other Miscellaneous Works.

Issued by Boards / Undertakings / PSU · Raipur, Chhattisgarh
Tender Value
1.50 Crore
Estimated cost
Bid Submission
09 Dec 2026
18 days left
EMD
4.51 Lakhs
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Raipur → Chhattisgarh
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Improvisation Of Traffic Lane In Front Of Terminal Building At S.V. Airport, Raipur. Sh : Provision Of Drainage System And Other Miscellaneous Works.

BOQ

Name of Work:- Improvisation of traffic lane in front of Terminal Building at S.V. Airport, Raipur. SH : Provision of drainage system and other miscellaneous works.
Sl. No. Item Description
1CARRIAGE OF MATERIALS by Mechanical Transport including loading,unloading and stacking :i) Lime, moorum, building rubbish.a) for lead upto 2 km
2Brick work with common burnt clay modular bricks of class designation 5.0 in foundation and plinth in: a) Cement Mortar 1:6 (1 cement : 6 coarse sand).
3Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: a) 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
4Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :a) Gutter (1200 mm over all girth)
5Providing and Fixing of GI Gutter Spout of size 400mm dia as per direction and satisfaction of Engineer-in-charge.
6Providing and applying Micro Concrete (REARM) solution below and around the base plate of colum as per direction and satisfaction of Engineer-in-charge.
7Centering and shuttering including strutting, propping etc. and removal of form for a) Columns, Pillars, Piers, Abutments, Posts and Struts including Extra for shuttering in circular work (20% of respective centering and shuttering items).
8Providing and fixing of rebars with TMT reinforcement bars of grade 500D or more in RCC Structures at all levels including drilling of RCC, fixing of TMT bars in position including grouting with suitable material as per direction of Engineer-in-charge.
9Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.a) Thermo-Mechanically Treated bars of grade Fe-500D or more.
10Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
11Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. a)Electric resistance or induction butt welded tubes
12Welding by gas or electric plant including transportation of plant at site etc. complete.
13Providing flat iron brackets 50x 3 mm size at maximum spacing of 1.0 m with necessary bolts, nuts and washers etc. for fixing gutters with purlins or other steel members as directed by engineer in charge.Note : Longitudnal Length of gutters shall be measured for payment
14Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. a) In cement mortar
15Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. a) For thickness of tiles 10 mm to 25 mm
16Painting with PU paint of approved brand and manufacture on M.S. structural steel/sheets/surfaces as per manufactures specification i/c surface scrapping, sand papering, sand blasting and applying epoxy priming coat etc complete with spraying or brush as per site requirement & direction of Engineer-in-charge.
17Designing, fabricating, testing, installing and fixing in position CurtainWall with Aluminium Composite Panel Cladding, with open grooves forlinear as well as curvilinear portions of the building , for all heights and alllevels etc. including: (a) Structural analysis & design and preparation of shop drawings forpressure equalisation or rain screen principle as required, proper drainageof water to make it watertight including checking of all the structural andfunctional design. (c) The fastening brackets of Aluminium alloy 6005 T5 I MS with HotDip Galvanised with serrations and serrated washers to arrest the windload movement, fasteners, SS 316 Pins and anchor bolts of approvedmake in SS 316, Nylon separators to prevent bi-metallic contacts allcomplete required to perform as per specification and drawing The itemincludes cost of all material & labour component, the cost of all mockups at site, cost of all samples of the individual components for testingin an approved laboratory, field tests on the assembled working curtainwall with aluminium composite panel cladding, cleaning and protection ofthe curtain wall with aluminium composite panel cladding till the handingover of the building for occupation. Base frame work for ACP claddingis payable under the relevant aluminium items. The Contractor shallprovide curtain wall with aluminium composite panel cladding, havingall the performance characteristics all complete , as per the Architecturaldrawings, as per item description, as specified, as per the approved shopdrawings and as directed by the Engineer-in-Charge. However, for thepurpose of payment, only the actual area on the external face of thecurtain wall with Aluminum Composite Panel Cladding (including width ofgroove) shall be measured in sqm. up to two decimal places.
18Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. a) Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent
19Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.i) Granite stone slab of colour black, Cherry/Ruby red. a) Area of slab upto 0.50 sqm
20Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
21Providing and laying Pavement Quality Concrete (PQC) produced in a batching and mixing plant having a Characteristic flexural strength i.e. flexural strength of 4.1 MPa at 28 days using Ordinary Portland cement of 43/53 grade or Portland Pozzolana Cement or Portland Slag cement conforming as per relevant IS codes, to be mixed at site, with 0.5% Super plasticizer by mass of cementitious material, fine aggregate, graded stone aggregates of 40 mm nominal size in appropriate proportion as per specification and job mix formula, laid in panels as per drawings/design as approved by the Engineer-In-Charge using Slip Form Paver or Fixed form paver including anti friction layer, joint filler board, making necessary provision for expansion, dummy and construction joint including filling with Polysulphide sealant of approved make, curing and making profile, complete as per direction of Engineer-in-Charge and specifications. The item for Execution shall include all operations making pavement for intended use but not limited to following:(i) Polyethylene sheet (White in color) of thickness 400 micron conforming to IS: 2508 with 6mm thick fine sand layer.(ii) Providing and laying in position for expansion joint, 25mm thick pre-cut Synthetic joint filler board of approved make conforming to IS:1838(part 3)-2011, 45 mm from top (to be removed at the time of filling of Polysulphide sealant).(iii) Mechanically cutting dummy joints 3mm wide x 1/3rd thickness of slab which is subsequently widened to 10mm for the top 25mm depth and construction joints 10mm wide x 25mm deep as per specification.(iv) Providing and laying in position Polysulphide sealant of approved make conforming to BS-5212-1990 or IS: 11433-1995 in expansion/ construction / dummy joints including rounding off edges, applying 2 coats of approved primer compatible with the brand of Polysulphide and preparing the surface and applying masking tape along the edge of joint to prevent accidental spillage of sealant on top surface and to give neat finish to the sealant and removing the masking tape after application of sealant etc. as per the details below:
22(a) Expansion Joints of size 25 mm wide and 10 mm deep over 30mm dia expanded closed-cell Polyethylene foam back-up/backer rod of minimum density 22 Kg/Cum, as per manufacturer’s specifications and sketch at Appendix-‘A’.(b) Construction Joints of size 10 mm wide and 10 mm deep over 12mm dia expanded closed-cell Polyethylene foam back-up/backer rod of minimum density 22 Kg/Cum, as per manufacturer’s specifications and sketch at Appendix-‘A’.(c) Dummy Joints of size 10 mm wide and 10 mm deep over 12 mm dia expanded closed-cell Polyethylene foam back-up/backer rod of minimum density 22 Kg/Cum, as per manufacturer’s specifications and sketch at Appendix-‘A’.(v) Making profile as per DGCA CAR, panel drawing showing dummy, construction, expansion joints location.Note:(i) Areas inaccessible to paving equipment shall be constructed by manual/hand guided method. Areas in which manual/hand guided methods of construction become indispensable shall be got approved by the Engineer-in-Charge in writing in advance.(ii) The quantity of cement, type of cement and super plasticizer for one Cum. of finished concrete specified are for tendering purpose only. The contractor shall quote his rates assuming quantity of OPC cement as 360 Kg/Cum or 400 Kg of Portland Pozzolana Cement/ Portland Slag cement. In addition, if the actual quantity of cement & super plasticizer required as per laboratory mix design varies from the quantity assumed above, necessary cost adjustment for deviation in the quantity of cement and super plasticizer as per mix design, if any, shall be done as per the rate of cement and super plasticizer in actual supply voucher from manufacturer/authorized dealer at the time of execution. In the case of authorized distributor, the rate may be authenticated by the manufacturer. The rate of cement and super plasticizer exclusive of GST shall only be considered for payment.
23Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :a) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
24Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)
25Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :i) For fixed portiona) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Please Enable Macros to View BoQ information
26Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :i) For fixed portiona) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58593470
AUTHORITY Boards / Undertakings / PSU
TENDER VALUE 1.50 Crore
LAST DATE 09-12-2026
Authority
Authority Name Airports Authority Of India
Work Description Tender for Improvisation Of Traffic Lane In Front Of Terminal Building At S.V. Airport, Raipur. Sh : Provision Of Drainage System And Other Miscellaneous Works.
Basic Detail
Tender No AAI/Raipur/Engg-Civil/Canopy Drainage and Divider/2026
Bidding Type Tender
Location
City Raipur
State Chhattisgarh
Key Dates
Publish Date 18 Nov 2026
Submission Date 09 Dec 2026
Open Date 11 Dec 2026
Finance
Tender Value 1.50 Crore
Tender Fee 1180
EMD 4.51 Lakhs
Exemption Not Available
Document List
65eca402-dce9-4988-b8e7-75a024a24322.html
BOQ_347427.xls
DNIT.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 18, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 09, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 18 days
Dec 11, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 20 days

Tender Documents

Download All (ZIP) ↓
html

65eca402-dce9-4988-b8e7-75a024a24322.html

xls

BOQ_347427.xls

pdf

DNIT.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender