Tender For Renovation Of Hostel Including Toilet, Floor, Window, Kitchen, Roof, Fan And Electrical Work At Residential Girls Hostel, Sewai, Simdega.
Tender Value
99.95 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
6 days left
EMD
2 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Simdega → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Hostel Including Toilet, Floor, Window, Kitchen, Roof, Fan And Electrical Work At Residential Girls Hostel, Sewai, Simdega.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down old door and window shutters including stacking serviceable materials within 15M. lead and disposal of unserviceable materials with all leads all complete as per direciton of E/l. |
| 2 | Taking down chowkhat in doors including stacking serviceable materials within 15M. lead and disposal of unserviceable materials with all leads all complete as per direciton of E/l. |
| 3 | Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l. |
| 4 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item - A) and disposal of excavated earth to a distance up to 50m. Including all lifts with levelling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design & building specification and direction of E / I |
| 5 | Extra for earth work in hard soil as per specification and direction of E/I (vide classification of soil item - B)Quantity same as per above item no. 1 |
| 6 | Earth fillng in foundation trenches and plinth in layers not exceeding 150mm. thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenches wtith a lead of 50M. And lift of 1.5M. All complete as per building specification and direction of E/I (Mode of measurement - compected volume)Quantity same as per item no. 1 i.e. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:2:4(1Cement :2 coarse sand (zone-III):graded stone aggregate 20 mm nominal size).1:2:4(1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20mm nominal size) |
| 8 | Supplying, fitting and fixing 20 guage G.C.I, sheet gate fitted on M.S. Angle frame of size 60x60x6mm. including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. |
| 9 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15 mm. depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/l. |
| 10 | Extra for cleaning the old surface by scrapping the entire old white wash or colour wash including cost of scaffolding all complete as per direction of E/l. |
| 11 | Providing 12mm thick cement plaster (1:6) with clean sand of F.M. 1.5 including screening , curing with all leads & lifts of water scaffolding taxes and royality all complete as per building specification and direction of E/I. |
| 12 | Providing 6mm thick cement plaster (1:4) in ceilling with clean sand of F.M. 1.5 including screening , curing with all leads & lifts of water scaffolding taxes and royality all complete as per building specification and direction of E/I. |
| 13 | Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. |
| 14 | Providing two coats of oil bound distemper of approved shade and make over old surface including washing, cleaning and papering the walls, scaffolding, washing of floors and taxes, all complete as per building specification and direction of E/l. |
| 15 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l. |
| 16 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) |
| 17 | Providing & Applying high quality acrylic modified resin based textureof Dholpur/Red sand stone Pattern with anti algae and UV resistanceproperties to be applied as intermediate finish in desired pattern @43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrappingand properly cleaning the surface to remove loose particles from theplaster surface, followed by top coating with Premium Acrylic Smoothexterior paint with Silicone additives of required shade by two ormore coats @ 1.43 litres/10 sqm, complete as the direction ofEngineer -in-Charge. |
| 18 | Labour for scrapping old paint with paint remover and blow lamp as required on wooden or steel surface including cost of all labour and materials and scaffolding all complete as per building specification and direction of E/l. |
| 19 | Providing two coats of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all comple as per building specification and direction of E/I. |
| 20 | Dismantling R.C.C.work including stacking serviceable materials in countable stacks within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l. |
| 21 | Reinforced cement concrete work in walls (any thickness) includ beams,suspended floors ,roofs having slope upto 15\\" landing, balcony,shelves,chajjas,lintel,band, plan window,sills staircase and sprial staircase above plinth level upto floor five level excluding cost of ,shuttering finishing and reinforcement with 1:1.5:3 (1 cement :1.5 corse sand (zone-III):3 graded stone aggregate 20 mm nominal size) |
| 22 | Centering and shuttering including strutting,proppingetc.and removal of form for foundation,footing ,bases of colunmns ,etc for mass concrete. Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 23 | Suspended floors, roofs, landings, balconies and access platform |
| 24 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 25 | Providing TMT steel reinforcement 8mm dia. rod 12mm dia as per approved design & drawing excluding the carriage of M.S. rods (straight or in coils) to work site, cutting, bending, and binding with anneled wire with the cost of wire removel of rust placing the rods in position all complete as per building specification and direction of E/I. 8mm Dia |
| 26 | Providing TMT steel reinforcement 8mm dia. rod 12mm dia as per approved design & drawing excluding the carriage of M.S. rods (straight or in coils) to work site, cutting, bending, and binding with anneled wire with the cost of wire removel of rust placing the rods in position all complete as per building specification and direction of E/I.10 mm Dia |
| 27 | Providing TMT steel reinforcement 8mm dia. rod 12mm dia as per approved design & drawing excluding the carriage of M.S. rods (straight or in coils) to work site, cutting, bending, and binding with anneled wire with the cost of wire removel of rust placing the rods in position all complete as per building specification and direction of E/I.12mm Dia |
| 28 | Dismantling tile work in floors and roofs laid in cement mortar includingstacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm |
| 29 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading,transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leadsincluding all lifts involved. |
| 30 | Providing and laying water proofing treatment in sunken portion of WCs,bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with waterproofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with waterproofing cement compound @ 0.126 kg/sqm. This layer will be allowed toair cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 31 | Providing coarse clean sand filling in foundation trenches and plinth including ramming and watering in layers not exceeding 150mm thick with all leads & lifts including the cost of all materials, labour, royality, & taxes all complete as per building specification and direction of E/I (Mode of measurement - compected volume). |
| 32 | Providing designation 75B one brick flat soling joints filled with local sand including the cost of watering taxes royality all complete as per building specification and direction of E/I. |
| 33 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:2:4(1Cement :2 coarse sand (zone-III):graded stone aggregate 20 mm nominal size). |
| 34 | Providing and laying rectifified Glazed Ceramic floor tiles of size 300 X 300 mm (thickness to be specified by the manufacture)of 1st quality conforming to IS:15622 of approved make in all colours & shades except White,lvory, Grey, Fume Red Brown,laid on 20mm thick bed of cement mortar 1:4 including grouting the joints with white cement and matching pigments etc.complete. Size 300mm x 300mm.. |
| 35 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing polishing and cost of curing, taxes and royality all complete as per building specification and direction of E/I. |
| 36 | Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory adesigned ready to use, acrylic modified flexible,\fbrush, roller or sprayeppled wate r proof i n g coati n g as per man ufactl rer specificatio r-(Withfollowing steps :-(a)surface preparation :-Provrding and cleaning of concrete surface toremove dLrst, oil, grease including removal of existing loose paint /coating, and cement laitance by cleaning with compressed air & water jetincluding all materials, labour, tools complete. Ponding test to be doneafter plugging all outlets and to be checked from sofftt to identify seepage,leakage. On identiiication of seepage, cement grouting to be done withnon shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg/ Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners andjoinis such as those betr,veen the parapet wall and the roof slab etc shall |
| 37 | Covering of treated surface wrth PCC :- Providing 25 mm thick Cement Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixingcerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr |
| 38 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :3 trak |
| 39 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm) |
| 40 | Providing & fixing fly proof wire gauze to windows, clerestory windows &doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 41 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulusof elasticity 900 N/mm2 and resistance to spread of flame of Class Acategory with property of being termite/borer proof, water/moistureproof and fire retardant and fixed in position with M.S hold fast/lugs/SSdash fasteners of required dia and length complete as per direction ofEngineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall bepaid for separately).Note: For WPC solid door/window frames, minus 5 mm tolerance indimensions i.e depth and width of profile shall be acceptable. Variation inprofile dimensions on plus side shall be acceptable but no extra paymenton this account shall be made.Frame size 65 x 100 mm |
| 42 | Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in-charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2,modulus of elasticity 850 N/mm2 and resistance to spread of flame ofClass A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) framemade of 25 x 25 x 1.5 mm square hollow box section including applyinga priming coat of approved steel primer, placed at grid made at 1.0 x 1.0m or as per requirement at site with necessary stainless steel fastenersand SS screws etc., all complete as per direction of Engineer-In- Charge.(Note: M.S (mild steel) framework with priming coat and necessary SSfasteners and SS screws shall be paid separately. |
| 43 | Providing and fixing factory made P.V.C. door frame of size 50x47 mmwith awall thickness of 5 mm, made out of extruded 5mm rigid PVCfoam sheet, mitred at corners and joined with 2 Nos of 150 mm longbrackets of 15x15 mm M.S. square tube, the vertical door frame profilesto be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDMrubber gasket weather seal to be provided through out the frame. Thedoor frame to be fixed to the wall using M.S. screws of 65/100 mm size,complete as per manufacturer’s specification and direction of Engineerin-Charge. |
| 44 | Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides.The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 45 | Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: |
| 46 | Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l. |
| 47 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 48 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l. |
| 49 | Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l. |
| 50 | Providing and laylng Doublecharge vitrrfied floor tiles in different sizes (thickness to be specified by the manufactre } with water absorption less than 0.08% and confcrming to lS: 15622/ISO 13006 of approved make, in all colours and shadds, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointrng with grey cement slurry @ 3 3 kg/ sqm includin grouling the loints with white cement and matching pigments etc ,complete step tiles & have bullnose,anti and self embossed line size of tiles 600x600 mm |
| 51 | Providing and laylng vitrrfied floor tiles for step of stair in with water absorption less than 0.08%and confcrming to lS: 15622, of approved make, in all colours and shadds, laid on 20mrr thick cement mortar 1:4 (1 cement : 4 coarsesand), jointrng with grey cement slurry @ 3 3 kg/ sqm includin grouling the loints with white cement and matching pigments etc ,complete step tiles & have bullnose,anti and self embossed line size of tiles 1200x300 mm x 15 mmFor Stair |
| 52 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.) |
| 53 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6(1 cement : 3 coarse sand (zone-Ill) derived from natural sources :6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, includingnecessary excavation, levelling & dressing & finishing the top smooth.. |
| 54 | Providing designation '100 A brick work with fly ash lime brick (FLAG) confirming to lS 12894-199C (9\\"x4.5'x3\\") in C M (1 :6)in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5inciudinq providing 10 min thick mo(ar joints, cost of screening materials,rakinq out loirrts to 15mm depth, curing, taxes and royalty allcomplete.as per building specification and direction of E/|. |
| 55 | Reinforced cement concrete work in walls (any thickness) including attached pillasters,buttresses,plinth and string courses fillets ,columns pillars,piers abutments ,post and struts etc.above plinth level ,excluding cost of ,shuttering finishing and reinforcement with 1:1.5:3 (1 cement :1.5 corse sand (zone-III):3 graded stone aggregate 20 mm nominal size) |
| 56 | Supplying,at site angle iorn post and strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and driling holes upto 10 mm etc.complete. |
| 57 | Providrng desrgnation 100 A brick work with fly ash lime brick (FLAG) c,:nflri-ning to IS 12894-1990 (9\\"x4.5'x3\\") in C M ('1 .6 )in foundation arrd plinth rvith approved quality of clean coarse sand of F.M. 2 to 2.5including providing 1O nrm thici< mortar joints, cost of screening materials, rcrkingout jr:inis to '15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/|. |
| 58 | Providing and fixing concertina coil fencing with punched tapeconcertina coil 600 mm dia 10 metre openable length ( total length90 m), having 50 nos rounds per 6 metre length, upto 3 m height ofwall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apartand with 9 horizontal R.B.T. reinforced barbed wire, stud tied withG.I. staples and G.I. clips to retain horizontal, including necessarybolts or G.I. barbed wire tied to angle iron, all complete as per directionof Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Springcore (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mmwith tape (0.52 mm thick) and weight 43.478 gm/ metre (cost ofM.S. angle, C.C. blocks shall be paid separately) |
| 59 | Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume). |
| 60 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). |
| 61 | Providing 150mm. wide brick drain in cement mortar (1:6) with av. 125 mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l. |
| 62 | Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 63 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 64 | Constructing brick masonry road gully chamber 50x45x60 cm withbricks in cement mortar 1:4 (1 cement : 4 coarse sand) including500x450 mm pre-cast R.C.C. horizontal grating with frame completeas per standard design :With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 |
| 65 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 66 | Providing and fixing precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by Engineer-in-charge 0.50mm (+ 0.05%) total coated thickness with zinc coating 120 grams per Sft.. as per IS : 277, in 240 mpa steel grade, 5-7 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 meter or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 67 | Providing and fixing precoated galvanised steel sheet roofingaccessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm) |
| 68 | Carriage of materials by diesel truck including loading at source, unloading at works site and stacking properly, labour, P.O.L. etc. all complete as per direction of E/I. (i)Fly ash lime Brick/Brick lead 8 KM (1k+7p) |
| 69 | (ii) Sand with avg.lead10 KM |
| 70 | (iii)Stone chips with avg.lead 8 KM |
| 71 | (iv)Earth work with avg.lead 3KM |
| 72 | Dismantling W.C. Pan of all sizes including disposal of dismantledmaterials i/c malba all complete as per directions of Engineer-in-Charge. |
| 73 | S / F / F viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S approved make with 100mm. H.C.I. 'p' trap 15 liters C.I. pull & let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm. alkathene / PVC telescupice flush, pipe about 2.00 m. long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthen ware foot rest to be fixed in floor 15 mm. C.I. body brass spindle stop cock of weight not less than 50 grams, 15mm. PVC connecting pipe 450 mm. long and the exposed pipe and cistern eith two coats of approved paints over a coat of red oxide primer etc. all complete as per specification and direction of E / I.580 mm. long with 12.5 liter low level PVC cistern |
| 74 | Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with \\"p\\" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. |
| 75 | Providing and fixing PTMT towel rail complete with brackets fixed towooden cleats with CP brass screws with concealed fittingsarrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm,78 mm wide and effective height of 88 mm, weighing notless than 170 gms |
| 76 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 77 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore. |
| 78 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter |
| 79 | Supplying and installtion Polythine water storage tank all complete as per direction of E / I. |
| 80 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. |
| 81 | Flush pipe with union spreaders and clamps all in C.P. brass forsingle stall (including C.P and Fitting) |
| 82 | Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l. |
| 83 | Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS :13592 type A including jointing with seal ring conforming to IS : 4382, leaving 10mm gap for thermal expension,single socketed pipes 75 mm. Dia. PVC pipe, |
| 84 | Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS :13592 type A including jointing with seal ring conforming to IS : 4382, leaving 10mm gap for thermal expension 110 mm. Dia. PVC pipe, |
| 85 | Providing and fixing on wall face unplasticised PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expension.Single push fit coupler 100 mm. dia. |
| 86 | Bend 110 mm. dia. |
| 87 | Shoe 110 mm dia. |
| 88 | Providing and fixing to the intel mouth of rain water pipe cast iron greetings 15 cm diameter and weighing 440 grams. |
| 89 | Providing and fixing unplasticised -PVC pipe clips of approved designto unplasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length, including cuttingbrick work and fixing in cement mortar 1 : 4 (1 cement: 4 coarse sand) andmaking good the wall etc. complete.110 mm |
| 90 | Providing and fixing Chlorinated polyvinyl Chloride(CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching,refilling & testing of joints complete as per direction of Engineer in Carge.15 mm nominal outer dia pipes |
| 91 | 20 mm nominal outer dia Pipes. |
| 92 | 32 mm nominal outer dia Pipes. |
| 93 | Making holes in walls for laying G.l. pipes and restoring the same after pipe lavinq as per specification and direction of E/|.(d) 250mm thick wall |
| 94 | Providing and fixing Gun metal full way valve of approved quality, allcomplete, as per specification and direction of E/|.(d) 32 mm dia.wt not less than 700 gms |
| 95 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 96 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore 15 mm nominal bore, |
| 97 | Providing and fixing C.P. brass stop cock (concealed) of standarddesign and of approved make conforming to IS:8931.15 mm nominal bore, |
| 98 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931,15mm nominal bore, |
| 99 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge |
| 100 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia. |
| 101 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,32 mm Diahaving thermal stability for hot & cold water supply, including allCPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.32 mm nominal outer dia Pipes |
| 102 | Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS : 2800 (partI) including necessary bolts & nuts of requried size complete.Rate=2019.05/1.2254 |
| 103 | S/F/F 4 core 6 sq.mm thick copper wire to connset submersible with all complete job. |
| 104 | Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 2HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 1.5 HP |
| 105 | Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914.F.A.S.D starter upto 5 to 10 H.P |
| 106 | Point re-wiring in existing conduit :-Rewiring for light point/fan point/exhaust fan point/ call bell point 1.5sq.mm FR PVC insulated copper conductor single core cable in existingsurface / recessed Steel/PVC conduit including dismantling as required |
| 107 | Twin coatol Point re-wiring in existing conduit :-Rcwiring for nrin conhol light point with 1.5 sq.mm FR PVC insulatedcoppcr conductor single core cable in existing surface / recessed steeVPVCconduit including dismantling as required |
| 108 | Wirilg in cxisting conduit :-ls\\"ppfyr\\"g and drawing following sizes of FR PVC insulated copperlconductor single core cable in existing zurface / recessed steel / PVCloonarit including dismantling as required 2x1.5 sq.mm |
| 109 | 2x2.5 sq.mm |
| 110 | 2x4 sq.mm |
| 111 | S/F PVC/G.I. boxes :-Supplying and fixing of following sizes of PVC/G.I box on surface / recesswith suitable size of phenolic laminated sheet cover in front includingpainting etc. as required.170 mm xZ2lmmx 48mm deep/ (8\\" x 10\\") |
| 112 | Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit with modular type, Group A |
| 113 | Wiring for light/power plug with 2x4sq.mm FR PVC insulated copper conductor single core cable |
| 114 | Circuit/ submain wiring in PVC conduit :-Wiring for circuit/ submain wiring along with earh wire with the followingsizes of FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit as required. 2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 115 | 2x2.5 sq.mm + 1x2.5 sq.mm earth wire |
| 116 | 2 x 4.0 sq.mm + I x 4.0 sq.mm earth wire |
| 117 | SIF power plug point with piano type accessories :-Supplying and fixing suitable size GI/PVC box of 121 mm x l73mm x48mm/(6\\" x 8\\") (nominal size ) on surface or in recess with suitable size ofphenolic laminated sheet cover in front including providing and fixing 6 pinl5/16 amps socket outlet and l5/16 amps piano tlpe switch. connection,painting etc. as required |
| 118 | Supplying and fixing following modular type switch/ socket on the existing switch box/cover.5/6 amps, one way switch |
| 119 | Supplying of XLPE alluminium armoured cable with all complete job. 16sqmm, 4 core |
| 120 | lS/F Piaoo type switch/ socket :-lSupptyrng and fxing of following piano type switch / socket on the existinglswitch box / cover including connections etc. as requted.5/6 amps, one way switch |
| 121 | 3 pin 5/6 amps, socket outlet |
| 122 | 15/16 amps, 6 pin socket outlet |
| 123 | Supplying and fixing batten holder including connection etc. as required. |
| 124 | Supplying and fixing 2 pin, 5 amps ceiling rose on existing junction box/ wooden block including connection etc. as required. |
| 125 | S/F rewireable double pole/TP&N switch disconnector - Providing and fixing following capacity double pole/TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc as required.16 amps, double pole |
| 126 | 32 amps, TP&N |
| 127 | 63 amps, TP&N |
| 128 | 100 amps, TP&N |
| 129 | S/F following way single pole neutral, sheet, MCB distribution board, 240 volts on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)8 way, single door |
| 130 | S/F 15/16 watt LED Bulb |
| 131 | Supply Installation, testing and commissioning of follwing size ceiling fan 3Blades confirming to13:374,.2019 including wiring the down rods ofndard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wireuitable for 230V 50H2, single phase supply etc. complete as required.l200mm (48\\") Ceiling Fan |
| 132 | S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughenedglass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC, 50H2. Luminarieshall be confirm to IS: 10322 part-5/section-5 and shall be complete with all neccssary accessories asrequired 30W LED Flood light |
| 133 | Supply of 9\\" (230mm) metal exaust fan Fan Bajaj/Crompton or any other approved make etc |
| 134 | S.I.T.C of floowing rating surface mounted LED tube light fitting suitablefor 230V 50H2, single phase supply etc. complete as required.10/12W LED Tube light |
| 135 | P/p G.I. lightning condutor finial :-Providing and fixing of lighting conductor finial , made of 25mm dia300mm long , G.I. tube, having single prong at top, with 85mm dia 6mmthick G.I. base plate including holes etc. complete as required. |
| 136 | Pff G.I. lightning conductor tape in horizontal mn :-Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface ofwall for lightning conductor complete as required.( for Horizontal run ). |
| 137 | PIF G.I. lightning conductor tape in vertical run :-Providing and fxing G.I. tape 20mm x 3rrm thick on parapet or surface ofwall for lightning conductor complete as required.( for Vertical run ). |
| 138 | Fixing lightring conductor tape in horizontal run :-Fixing of copper/G.L tape 20mrn x 3mm thick on parapet or surface of wallfor lightning conductor complete as required.( for horizontal n n ). |
| 139 | Fixing lightning conductor tape in vertical run :-Fixing of copper/G.I. tape 20mm x 3mm thick on parapet or surface of wallfor lightning conductor complete as required.( for vertical run ). |
| 140 | Earthing with copper earth plate 600mm x 600mm x 3mm thick Including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (but without charcoal or coke and salt) |
| 141 | Supply and laying 8 SWG coppcr wirc at 0,50 metre below ground level for conductor earth electrode, including solding etc. as required. |
| 142 | Add 18 % GST (in Basic Rate must fill 12) |
| 143 | Add 1% Labour Cess (in Basic Rate must fill 1) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender