Tender For Providing Borewell And Water Supply Arrangements For Government Higher Secondary School At Kotamalam In Erode District.
Tender Value
4.45 Lakhs
Estimated cost
Bid Submission
03 Dec 2026
14 days left
EMD
4500
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Erode → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing Borewell And Water Supply Arrangements For Government Higher Secondary School At Kotamalam In Erode District.
BOQ
| Sl. No. | Item Description |
| 1 | Drilling of 6\\" dia (150mm) vertical bore of hard rock areas to any required depth as directed by the departmental officers rate is inclusive of labour charges for inserting casing pipe assembling the equipment in piont as selected welding the casing pipe if necessary and also tranportation charges for the rig and supporting vehicle from one place to another etc., complete complying with standard specifications. |
| 2 | Upto 150m below Ground level |
| 3 | From 151m upto 180m |
| 4 | From 181m upto 210m |
| 5 | From 211m upto 240m |
| 6 | From 241m upto 270m |
| 7 | Supplying and fixing in position best approved of BIS quality 160mm dia Special Blue Pipes for Bore well including cost of necessary fittings and accessories etc., complete complying with standard specification and as directed by the departmental |
| 8 | Supplying and fixing of suitable PVC end cap (6Kg/cm2) for 6\\" dia bore well of best quality with ISI mark. (The PVC end cap should be got approved by the departmental officers before execution) |
| 9 | Supply and laying of 2 core 1.5 sq.mm armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers. |
| 10 | Supply and fixing of 40mm dia CPVC(Chlorinated Poly Vinyl Chloride) pipe(Higher Pressure rating with higher pipe thickness) Standard dimension ratio of best and approved quality for delivery cum support pipe for submersible motor install inside borewell etc, complete complying with standard specification and as directed by the departmental officers. |
| 11 | Supplying and fixing erecting 5.00 HP (DECCAN MAKE) ISI make bore well SUBMERSIBLE PUMPSET with required accassories for the 5.0HP ISI make3 phase electricmotar 2900rpm, 400/S.S. shaft cable of discharging 100 to 200 LPM against a total Head of 135m to 100m with ISI mark and an outlet of 50mm and suitable for 150mm dia bore well including supplying and fixing M.S. fabricated wall mounting Pannel board with internal wiring as per I.E. rules and necessary locking arrangements with suitable cutler and hammer type bush button automatic 10 HP texvel DOL starter 1 no, suitable 15 Amp, TPIC switch, 0 to 500 v Voltmeter, 0 to 20 Amps Ammeeter, single phase preventer. pilot lamps with 3 bulps to indicate power supply and 50mm dia GI couplying 2 nos, M. S. clamps 2 nos, 2.5 Sq mm wire 3 core copper flat submergible cable, including Conveyance and Erection charges including required G. I. pecials, MR Tape Electrical connection charges., delivery pipe connection charges and other plumbing works including hire charges for Chain pully, tripod and other tools and trial run for three days etc., including labour charges complete complying as directed by the departmental officers |
| 12 | Supplying and fixing of Nylon rope complete complying with standard specification and as directed by the departmental offices. |
| 13 | Supplying and fixing of 3 Phase Panel Board including labour charges etc., complete as directed by the departmental officers. |
| 14 | Supplying & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550KG/Cub.MT & shore hardness of 55. The door shall be a plain matt board as decided by the Engineer-in-Charge of the department. The WPC door shall be fixed onto the Aluminium \\"G\\" type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4\\" in SS (Slinding Door) etc., complete and as directed by the departmental officers. |
| 15 | Fabrication, supply and fixing in position of ‘N’ type ventilators using M.S. angle of size 25 x 25 x5 mm for frame and M.S. Flat of size 20 x 3 mm for fixing the weld mesh and using 25 x 22 x3 mm ‘T’ section for frame glass. Special type of Hold fast welded to the frame of 45 degree inclined towards centre for wall and fxing the weldmesh 25mm square including cost of 3mm thick pinheaded glass panes for all panels and fixing the glass panels with necessary clips & putties with required bolts, nuts and washers and one coat of red oxide primer etc. including necessary dismantling, making holes in RCC columns, beams, masonry wherever necessary with power drill to the extend required and made good to the original conditions after fising complete complying with standard specification and as directed by the departmental officers |
| 16 | Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works) |
| 17 | CP screw down tap |
| 18 | Supplying and fixing in position of best quality PVC/SOIL/ waste pipe (6 Kg / cm2) of following size having ISI mark and providing leak proof joints including fixing to the wall with specials,PVC/ MS clamps etc.,and making connection to all sanitary fittings, dismantling the masonry /R.C.C works wherever necessary and redoing the dismantled portion to the original condition complying with standard specification etc., complete. (The P.V.C.Pipes should be got approved by the Executive Engineer before use on works) |
| 19 | 75mm dia PVC Soil / Waste Pipe |
| 20 | 110mm dia PVC Soil / Waste Pipe |
| 21 | Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). |
| 22 | 75 mm dia PVC Elbow with Door |
| 23 | 110 mm dia PVC Elbow with Door |
| 24 | Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn,teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works) White glazed European Water Closet with 10 litre capacity PVC flushing tank fixed on to wall |
| 25 | GST 18% Including GST 18% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysDec 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender