Power Government Departments Closing in 13 days TDR #58585337

Tender For Work Of Renovation Of The Existing Lt Lines Covering 41 Nos. Of Distribution Transformer Centres At V.P. Kirlapal Dabal Under The Tribal Sub-Plan In Sanvordem Constituency, Under The Jurisdiction Of Electrical Sub Div-Iv, Division Vii, Cur

Issued by Government Departments · goa, Goa
Tender Value
11.27 Crore
Estimated cost
Bid Submission
04 Dec 2026
13 days left
EMD
21.27 Lakhs
Bank guarantee accepted
Document Fee
1500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Work Of Renovation Of The Existing Lt Lines Covering 41 Nos. Of Distribution Transformer Centres At V.P. Kirlapal Dabal Under The Tribal Sub-Plan In Sanvordem Constituency, Under The Jurisdiction Of Electrical Sub Div-Iv, Division Vii, Curchorem

BOQ

Name of Work:- Work of renovation of the existing LT lines covering 41 Nos. of Distribution Transformer Centres at V.P. Kirlapal Dabal under the Tribal Sub-Plan in Sanvordem Constituency, under the jurisdiction of Elect. Sub Div-IV, Division VII, Curchorem
Sl. No. Item Description
1Supply
2Supply of RCC pole 9mtrs long R.C.C. Pole as per drawing approved by CEE and conforming to IS standards as amended upto date.
3Supply of RCC pole 7.5mtrs long R.C.C. Pole as per drawing approved by CEE and conforming to IS standards as amended upto date.
4Providing of Cement concrete in the ratio 1:2:4(1 cement: 2 Sand, 4 graded granite/basaltic, aggregate 20mm nominal size) including cost of centering, shuttering & muffing 0.4mts above the ground & properly curved
5Supply of Cross Arm Channel 4Pin .The cross arms shall be made of M.S. channel of ISMC-75 vide table 2 of IS: 8081 1964 . The cross arms shall be without any joints. The cross arms shall be hot dipped galvanized generally conforming to IS - 2633/72. The length of the 4pin cross arm shall be 1110mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm for clamping arrangement to the pole. The length of the 4pin side cross arm shall be 1410mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm 40 mm from the left edge of the X-arm for clamping arrangement to the pole & two holes of size 17mm dia at 355mm & 660mm from the slotted hole for arrangement to fix angle support. The angle support shall be of ISA 50x50x6mm G.I. with 17 mm dia holes at the two ends. The other end of the angle shall be clamps utilizing suitable G. I. stay clamps of length 312mm end to end [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
6Supply of Cross Arm Channel 2Pin .The cross arms shall be made of M.S. channel of ISMC-75 vide table 2 of IS: 8081 1964 . The cross arms shall be without any joints. The cross arms shall be hot dipped galvanized generally conforming to IS - 2633/72. The length of the 4pin cross arm shall be 1110mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm for clamping arrangement to the pole. The length of the 4pin side cross arm shall be 1410mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm 40 mm from the left edge of the X-arm for clamping arrangement to the pole & two holes of size 17mm dia at 355mm & 660mm from the slotted hole for arrangement to fix angle support. The angle support shall be of ISA 50x50x6mm G.I. with 17 mm dia holes at the two ends. The other end of the angle shall be clamps utilizing suitable G. I. stay clamps of length 312mm end to end [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
7Supply of HDGI 11KV V-Shape X arm [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
8Supply of Cut point Channel 1.3 mtr long [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
9Supply of HDGI Top fitting for 11KV [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
10Supply of HDGI Top fitting cross arm ISMC channel,75x40mm,0.7mts long [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
11Supply of 11KV guard cross arm, ISMC channel 75 x 40mm, 1.5mtr long [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
12Supply of GI Xarm clamp LA for 9.0mts pole shall be hot dipped galvanized generally conforming to IS - 2633/72 [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
13Supply of GI Xarm clamp SA for 9.0mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/73 [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
14Supply of GI stay clamp SA for 9.0mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/73 [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
15Supply of GI Xarm clamp LA for 7.5mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/74 [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
16Supply of GI Xarm clamp SA for 7.5mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/75 [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
17Supply of 11kv Pin insulators with GI pins
18Supply of 11kv Disc insulators with metal parts 45KN
19Supply of LT pin insulator with GI pin
20Supply of Insulator -(LT) Shackle .L.T. brown glazed shackle insulators of size 100mm x 115mm conforming to fig.No.4 and type 2 of IS: 1445/77 as amended upto date. Minimum failing load shall be 16kN. Insulators shall have marking and packing as prescribed in IS
21Supply of ACSR 'WEASEL' of size ( 6/1/2.59mm) for earthing and jumpering .Packing and marking of drum will be as per IS:Conductor length shall be 1500 mtr. with tolerance of +/- 5%
22Supply of conductor-AA ANT, 2. 7/3.10 mm .
23Supply of conductor -AA GNAT,1. 7/2.21 mm,
24Supply of Anticlimbing device(barbed wire).Hot dip galvanized steel barbed wire type 4 conforming to IS:278/1962 as amended upto date and galvanization conforming to IS:4826/1979as amended upto date
25Supply of 11KV Enamelled danger board of size 250mm x 200mm.
26Supply of Earthing complete with 2.5mts long, 40mm GI earthing pipe, class B, 20kgs each of salt and charcoal, excvation, re-filling etc chamber with brick masonary..Earthing pipe made of Hot Dip galvanized steel tube of heavy class, 40mm nominal bore conforming to IS 1239 Part 1 1990 as amended upto date and Hot Dip zinc coating shall conform to IS 4736-1968 as amended upto date
27Supply of Stay set complete for 9.0 mts RCC Pole.HDGI Stay Sets Complete Comprising of stay rod with plate, HDGI stay wire of size 7/10swg, Break insulator of 15KV/8KV,HDGI turn buckle with eye bolt, suitable HDGI stay clamps, HDGI nut bolts, . The Stay wire shall comply with the specific requirements of IS: 2141-1979, IS: 4826-1979 & IS: 6594-1974 or the latest versions thereof and also as per the specifications enclosed.
28Supply of Stay set complete for 7.5 mts RCC Pole.HDGI Stay Sets Complete Comprising of stay rod with plate, HDGI stay wire of size 7/10swg, Break insulator of 15KV/8KV,HDGI turn buckle with eye bolt, suitable HDGI stay clamps, HDGI nut bolts, . The Stay wire shall comply with the specific requirements of IS: 2141-1979, IS: 4826-1979 & IS: 6594-1974 or the latest versions thereof and also as per the specifications enclosed.
29Supply of HDGI D.P Structure Materials. All the materials shall be hot dipped galvanized [Galvanising should be hot dipped Galvanised as per IS:2629/66, minimum Zinc coating of 1000 gms/sq.mtr, 140 Microns DFT), suitable for high salinity coastal areas]
30Supply of 11 KV GOAB switch with 200 A.12 KV rated voltage GOAB switches tilting type, outdoor, manually operated, triple pole, single break, conforming to IS: 9921-Part1 to V as amended upto date and detailed specifications enclosed herewith. Each set shall comprise of six pedestal and three tilting post insulators. Insulator should be factory cemented by the manufactures of the insulators and have minimum 320mm creepage distance and AB switches contacts shall be of copper/copper alloy
31Supply of 11 KV HG fuse,200A, Horn gap type fuseI.TECHNICAL PARTICULARS:1. Highest System voltage : 12 KV (R.M.S)2. Impulse voltage withstand voltage : 75 KV (Peak)3. One minute power frequency withstand voltage : 35 KV (R.M.S.)4. Continuous current rating of the unit : 200 Amps
32Supply of 9 KV, 5A Lightning Arrestor, pole mounted.9 KV, 5 KA nominal discharge current Metal Oxide gapless distribution class lightning arrestor conforming to IEC-60099-4 and IS 3070 Part 3 1993 as amended upto date suitable for 11 KV 50 HZ effectively earthed neutral system with necessary mounting arrangements and connector suitable to connect ACSR conductor upto overall diameter 12.30 mm.The marking of the Lightning Arrestors shall be as per IS
33Supply of MS Distribution box complete.M. S. distribution box MCCB of 400Amps capacity Kit Kat Porcelain fuse carrier and base with extended terminals.
34Supply of Distribution Transformer metering unit
35Supply of HDGI nuts & bolts.G.I. Hexagonal head bolts and hexagonal nuts conforming to IS 1363 part 1 to 3 1992 as amended upto date.The bolts and nuts shall be hot dip galvanized as per IS: 2629-1985 as amended upto date
36Supply of XLPE armoured cable 3 & 1/2 core 240 sq.mm.The armoured cable shall be suitably terminated at both the ends with appropriate sizes of Aluminum lugs duly crimped using a crimping tool. Appropriate sizes of G.I / Brass nut / bolts / washers shall be used for firmly connecting the same to the MCCB’s/Transformer L.T. Bushings/Outgoing LT feeder
37Supply of XLPE armoured cable 3 & 1/2core 120 sq.mm.The armoured cableshall be suitably terminated at both the ends with appropriate sizes of Aluminum lugs duly crimped using a crimping tool. Appropriate sizes of G.I / Brass nut / bolts / washers shall be used for firmly connecting the same to the MCCB’s/Transformer L.T. Bushings/Outgoing LT feeder
38Supply of XLPE armoured cable 3 & 1/2 core 95 sq.mm(For Neutral).The armoured cable shall be suitably terminated at both the ends with appropriate sizes of Aluminum lugs duly crimped using a crimping tool. Appropriate sizes of G.I / Brass nut / bolts / washers shall be used for firmly connecting the same to the MCCB’s/Transformer L.T. Bushings/Outgoing LT feeder
39Supply of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes: 1)240Sq.mm
40Supply of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes:1. 120 Sq.mm
41Supply of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes:1. 95Sq.mm.
42Supply of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes:1. 70Sq.mm.
43Supply of FRP Fencing complete with Gate around every distribution sub-station containing , one distribution transformer and one LV switchboard including danger plate (Size 4Mx3Mx2M) with Concreting for FRP Fencing supports with plinth (0.3x0.3x0.5) Cu.m. x 12 nos. Each ratio 1:3:6
44Cost of Erection/ dismantling of old network
45Erection of 9 mts. long RCC poles .The poles should be as per drawing approved by CEE and conforming to IS standards as amended upto date. The Component used for pole shall conform to following IS amended upto date.
46Erection of 7.5mts. long RCC poles .The poles should be as per drawing approved by CEE and conforming to IS standards as amended upto date. The Component used for pole shall conform to following IS amended upto date
47Fixing of Cross Arm Channel 4Pin .The cross arms shall be made of M.S. channel of ISMC-75 vide table 2 of IS: 8081 1964 . The cross arms shall be without any joints. The cross arms shall be hot dipped galvanized generally conforming to IS - 2633/72. The length of the 4pin cross arm shall be 1110mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm for clamping arrangement to the pole. The length of the 4pin side cross arm shall be 1410mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm 40 mm from the left edge of the X-arm for clamping arrangement to the pole & two holes of size 17mm dia at 355mm & 660mm from the slotted hole for arrangement to fix angle support. The angle support shall be of ISA 50x50x6mm G.I. with 17 mm dia holes at the two ends. The other end of the angle shall be clamps utilizing suitable G. I. stay clamps of length 312mm end to end
48Fixing of Cross Arm Channel 2Pin .The cross arms shall be made of M.S. channel of ISMC-75 vide table 2 of IS: 8081 1964 . The cross arms shall be without any joints. The cross arms shall be hot dipped galvanized generally conforming to IS - 2633/72. The length of the 4pin cross arm shall be 1110mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm for clamping arrangement to the pole. The length of the 4pin side cross arm shall be 1410mm with 4 holes of 22 dia each on each flange section. In addition 2 holes of size 18mm x 40mm slotted holes shall be provided on the cross arm 40 mm from the left edge of the X-arm for clamping arrangement to the pole & two holes of size 17mm dia at 355mm & 660mm from the slotted hole for arrangement to fix angle support. The angle support shall be of ISA 50x50x6mm G.I. with 17 mm dia holes at the two ends. The other end of the angle shall be clamps utilizing suitable G. I. stay clamps of length 312mm end to end
49Fixing of HDGI 11KV V-Shape X arm
50Fixing of Cut point Channel 1.3 mtr long
51Fixing of HDGI Top fitting for 11KV
52Fixing of HDGI Top fitting cross arm ISMC channel,75x40mm,0.7mts long
53Fixing of 11KV guard cross arm, ISMC channel 75 x 40mm, 1.5mtr long
54Fixing of GI Xarm clamp LA for 9.0mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/72
55Fixing of GI Xarm clamp SA for 9.0mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/73
56Fixing of GI stay clamp SA for 9.0mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/73
57Fixing of GI Xarm clamp LA for 7.5mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/74
58Fixing of GI Xarm clamp SA for 7.5mts pole.shall be hot dipped galvanized generally conforming to IS - 2633/75
59Fixing of 11kv Pin insulators with GI pins
60Fixing of 11kv Disc insulators with metal parts 45KN
61Erection of LT pin insulator with GI pin
62Fixing of Insulator -(LT) Shackle .L.T. brown glazed shackle insulators of size 100mm x 115mm conforming to fig.No.4 and type 2 of IS: 1445/77 as amended upto date. Minimum failing load shall be 16kN. Insulators shall have marking and packing as prescribed in IS
63Stringing of ACSR 'WEASEL' of size ( 6/1/2.59mm) for earthing and jumpering .Packing and marking of drum will be as per IS:Conductor length shall be 1500 mtr. with tolerance of +/- 5%
64Stringing of conductor-AA ANT, 2. 7/3.10 mm .
65Stringing of conductor -AA GNAT,1. 7/2.21 mm,
66Fixing of Anticlimbing device(barbed wire).Hot dip galvanized steel barbed wire type 4 conforming to IS:278/1962 as amended upto date and galvanization conforming to IS:4826/1979as amended upto date
67Fixing of Enamelled danger board of size 250mm x 200mm
68Erection of Earthing complete with 2.5mts long, 40mm GI earthing pipe, class B, 20kgs each of salt and charcoal, excvation, re-filling etc Chamber with brick masonary. Earthing pipe made of Hot Dip galvanized steel tube of heavy class, 40mm nominal bore conforming to IS 1239 Part 1 1990 as amended upto date and Hot Dip zinc coating shall conform to IS 4736-1968 as amended upto date
69Erection of Stay set complete for 9.0 mts RCC Pole.HDGI Stay Sets Complete Comprising of stay rod with plate, HDGI stay wire of size 7/10swg, Break insulator of 15KV/8KV,HDGI turn buckle with eye bolt, suitable HDGI stay clamps, HDGI nut bolts, conforming to drawings approved. The Stay wire shall comply with the specific requirements of IS: 2141-1979, IS: 4826-1979 & IS: 6594-1974 or the latest versions thereof and also as per the specifications enclosed.
70Erection of Stay set complete for 7.5 mts RCC Pole.HDGI Stay Sets Complete Comprising of stay rod with plate, HDGI stay wire of size 7/10swg, Break insulator of 15KV/8KV,HDGI turn buckle with eye bolt, suitable HDGI stay clamps, HDGI nut bolts, conforming to drawings approved. The Stay wire shall comply with the specific requirements of IS: 2141-1979, IS: 4826-1979 & IS: 6594-1974 or the latest versions thereof and also as per the specifications enclosed.
71Fixing of HDGI D.P Structure Materials.
72Erection of 11 KV GOAB switch with 200 A.12 KV rated voltage GOAB switches tilting type, outdoor, manually operated, triple pole, single break, conforming to IS: 9921-Part1 to V as amended upto date and detailed specifications enclosed herewith. Each set shall comprise of six pedestal and three tilting post insulators. Insulator should be factory cemented by the manufactures of the insulators and have minimum 320mm creepage distance and AB switches contacts shall be of copper/copper alloy
73Fixing of 11 KV HG fuse,200A, Horn gap type fuseI.TECHNICAL PARTICULARS:1. Highest System voltage : 12 KV (R.M.S)2. Impulse voltage withstand voltage : 75 KV (Peak)3. One minute power frequency withstand voltage : 35 KV (R.M.S.)4. Continuous current rating of the unit : 200 Amps
74Erection of 9 KV, 5A Lightning Arrestor, pole mounted.9 KV, 5 KA nominal discharge current Metal Oxide gapless distribution class lightning arrestor conforming to IEC-60099-4 and IS 3070 Part 3 1993 as amended upto date suitable for 11 KV 50 HZ effectively earthed neutral system with necessary mounting arrangements and connector suitable to connect ACSR conductor upto overall diameter 12.30 mm.The marking of the Lightning Arrestors shall be as per IS
75Erection of MS Distribution box complete.M. S. distribution box MCCB of 400 Amps capacity Kit Kat Porcelain fuse carrier and base with extended terminals.
76Removing & re-erection of 200KVA Distribution Transformer
77Removing & re-erection of 100KVA Distribution Transformer
78Erection of Distribution Transformer Metering Unit.
79Providing of HDGI nuts & bolts.G.I. Hexagonal head bolts and hexagonal nuts conforming to IS 1363 part 1 to 3 1992 as amended upto date.The bolts and nuts shall be hot dip galvanized as per IS: 2629-1985 as amended upto date
80Erection of XLPE armoured cable 3 & 1/2 core 240 sq.mm.The armoured cable shall suitably terminated at both the ends with appropriate sizes of Aluminum lugs duly crimped using a crimping tool. Appropriate sizes of G.I / Brass nut / bolts / washers shall be used for firmly connecting the same to the MCCB’s/Transformer L.T. Bushings/Outgoing LT feeder
81Erection of XLPE armoured cable 3 & 1/2 core 120 sq.mm.The armoured cable shall be suitably terminated at both the ends with appropriate sizes of Aluminum lugs duly crimped using a crimping tool. Appropriate sizes of G.I / Brass nut / bolts / washers shall be used for firmly connecting the same to the MCCB’s/Transformer L.T. Bushings/Outgoing LT feeder
82Erection of XLPE armoured cable 3 & 1/2core 95 sq.mm(for Neutral).The armoured cable shall be suitably terminated at both the ends with appropriate sizes of Aluminum lugs duly crimped using a crimping tool. Appropriate sizes of G.I / Brass nut / bolts / washers shall be used for firmly connecting the same to the MCCB’s/Transformer L.T. Bushings/Outgoing LT feeder
83Providing of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes: 1)240Sq.mm
84Providing of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes:1. 120 Sq.mm.
85Providing of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes:1. 95Sq.mm.
86Providing of Aluminum crimping lugs shall conform to IS: 8309-1976 as amended upto date. Lugs shall be made of aluminium of grade 1E of IS 5082-1969 suitable for aluminium cables of following sizes:1. 70Sq.mm.
87Erection of FRP Fencing complete with Gate around every distribution sub-station containing RMU, one distribution transformer and one LV switchboard including danger plate (Size 4Mx3Mx2M) with Concreting for FRP Fencing supports with plinth (0.3x0.3x0.5) Cu.m. x 12 nos. Each ratio 1:3:6
88Removing of Rail poles 90 lb/yd 11 mtr long
89Removing of RCC poles 9 mtr long
90Removing of RCC poles 7.5 mtr long
91Removing of 4 pin cross arm
92Removing of 2 pin cross arm
93Removing of HDGI 11KV V shape X-arm
94Removing of cut point channel 1.3 mtr long
95Removing of HDGI Top Fitting for 11KV.
96Removing of HDGI Top Fitting cross arm ISMC Channel, 75x40mm,0.7mtrs long
97Removing of Shackle insulator with metal parts
98Removing of Pin insulator with GI Pin
99Removing & restringing of ACSR of weasel conductor
100Removing AA ANT conductor
101Removing AA GNAT conductor
102Removing of old Rail pole DP structure materials
103Removing of 11 KV GOAB switch 200A
104Removing 11 KV HG fuse set 200A
105Removing of 11kv Disc insulators with metal parts 45KN
106Removing of MS Distribution Box
107Removing of lightning arrestor
108Removing XLPE armoured cable 3 1/2 core 240sq.mm.
109Removing XLPE armoured cable 3 1/2 core 120sq.mm.
110Removing XLPE armoured cable 31/2 core 95sq.mm. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58585337
AUTHORITY Government Departments
TENDER VALUE 11.27 Crore
LAST DATE 04-12-2026
Authority
Authority Name Department Of Electricity
Work Description Tender for Work Of Renovation Of The Existing Lt Lines Covering 41 Nos. Of Distribution Transformer Centres At V.P. Kirlapal Dabal Under The Tribal Sub-Plan In Sanvordem Constituency, Under The Jurisdiction Of Electrical Sub Div-Iv, Division Vii, Curchorem
Basic Detail
Tender No Tender 42(2026-27)/CSC
Bidding Type Tender
Location
City goa
State Goa
Key Dates
Publish Date 18 Nov 2026
Submission Date 04 Dec 2026
Open Date 07 Dec 2026
Finance
Tender Value 11.27 Crore
Tender Fee 1500
EMD 21.27 Lakhs
Exemption Not Available
Document List
BOQ_33620.xls
ff487088-39a6-4c11-895e-9cb35c2440db.html
Tendernotice_1.pdf
Tendernotice_2.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 18, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 04, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 13 days
Dec 07, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 16 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_33620.xls

html

ff487088-39a6-4c11-895e-9cb35c2440db.html

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender