Defence Statutory Bodies & Commissions/Committees Closing in 18 days TDR #58581866

Tender For Provn Of 02 X Addl Class Rooms Alongwith Allied Infra Near Chanakya Block At Mcmm Jabalpur

Issued by Statutory Bodies & Commissions/Committees · Jabalpur, Madhya Pradesh
Tender Value
43.59 Lakhs
Estimated cost
Bid Submission
09 Dec 2026
18 days left
EMD
87180
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Provn Of 02 X Addl Class Rooms Alongwith Allied Infra Near Chanakya Block At Mcmm Jabalpur

BOQ

Name of Work:- PROVN OF 02 X ADDL CLASS ROOMS ALONGWITH ALLIED INFRA NEAR CHANAKYA BLOCK AT MCMM JABALPUR
Sl. No. Item Description
1Surface excavation in hard/dense soil n. exc 30 cm deep and avg 15 cm deep complete all as specified and directed.
2Excavation in trenches n.exc 1.50 mtr wide and n. exc 1.50 mtr depth, for foundation, manhole etc n.exc 10Sqm on plan and getting out in hard/dense soil complete all as specified & directed.
3M&L cement concrete (1:4:8) type D-2 (40 mm graded stone aggregate) as in sub base, mass concrete complete all as specified and directed.
4M&L ready mix RCC M-25 (Design Mix) (20 mm graded stone aggregate) as in foundation, raft, footing, plinth beam, base for column etc complete all as specified and directed. Note:- Only river sand will be use for reinforcement cement concrete work.
5Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished concrete surfaces complete all as specified and directed.
6Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete complete all as specified and directed
7M&L for ready mix RCC M-25 (Design Mix) (20 mm graded stone aggregate) as in column complete all as specified and directed. Note:- Only river sand will be use for reinforcement cement concrete work.
8Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete completed all as specified and directed.
9M&L for ready mix RCC M-25 (20 mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.50 m complete all as specified and directed.Note:- Only river sand will be use for reinforcement cement concrete work.
10Use and waste of formwork to sofits of suspended slabs such as roof slabs, floors slabs, landings and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed.
11M&L ready mix RCC M-25 (20 mm graded stone aggregate) as in slabs suppoorted on walls, beams and column in floors, roof, landings, balconies, canopies, deck slab and in shevels the like complete all as specified and directed.Note:- Only river sand will be use for reinforcement cement concrete work.
12M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
13All as per Item No 12 here-in-before but 8mm dia.
14All as per Item No 12 here-in-before but 8 mm dia and over upto and including 10mm dia in stirrups, spacers and binders
15M&L old size brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed
16M&L for old size brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick wall, built in CM 1:4 complete all as specified and directed
17M&L for 10 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed. Note:- Only river sand will be use for plastering work.
18M&L for 15mm thick rendering on fair faces of brick surfaces in CM (1:4), first coat 10 mm thick plaster in CM 1:4 and second coat 5 mm thick in CM 1:4 with using water proofing liquid finished surfaces even and smooth without using extra cement complete all as specified and directed. (with water proofing compound @ 200ml per bag off cement or as per manufacturers's instructions)Note:- Only River sand will be use for plastering work. WPC shall be measured and paid separately.
19M&L for 5mm thick rendering in CM (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.Note:- Only River sand will be use for plastering work
20M&L for 5mm thick rendering in CM (1:3) on RCC surface finished even and smooth without using extra cement complete all as specified and directed.Note:- Only River sand will be use for plastering work
21Forming embarkment including raising (or lowering) earth, spreading in layer n .exc 30 cm thick watering, ramming/rolling and finishing to required size and slope etc n.exc 1.5 mtr high from base complete all as specified and directed.
22M&L for broken stone or boulder hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.
23M&L for PCC 1:4:8 type D2 using 40mm graded aggregate, 100mm thick, as in sub base complete all as specified and directed.
24M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 20 mm thick screed bed in CM 1:6 complete all as specified and directed.
25M&L for kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 10 mm thick backing coat in CM 1:4 complete all as specified and directed.
26S&F Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of 15 mm thick screed bed in CM 1:6 complete all as specified and directed.
27M&L for Glazed ceramic tiles (450x300)x 8-10 mm thick, as in dado/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of 10 mm thick backing coat in CM 1:4 complete all as specified and directed.
28M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding laid over 20 mm thick screed bed in CM 1:4 rates including moulding and rounding complete all as specified and directed.
29M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite rates are including rounding and moulding complete all as specified and directed.
30M&L for 20-25mm thick Machine cut cudappah stone slab over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.
31S&F factory made steel windows with side hung shutters including projecting type hinges with lugs steel handles and steel peg stays, with glazing bars, devetailed or welded complete all as specified and directed.
32All as per item No 31 here-in-before but without glazing bars.
33M&L framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.
34S&F stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.
35M&L Sheet glass ordinary quality and glazing with oil putty in square n. exc. 0.5 sqm in each pane 3 mm thick complete all as specified and directed.
36M&L for rendering 10 mm thick on fair faces of concrete surface in cement mortar 1:3 for receive the roof finishes with water proofing liquid. (WPL Shall be measured and paid separately) complete all as specified and directed.
37M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms /sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 ltr/Sqm by forced complete all as specified and directed.Three course roof treatment consists of as under :- (a) Applying one coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr per sqm.(b) Laying of APP based membrane as specified thickness and weight.(c) Applying two coat of aluminium paint @ 100ml/sqm.
38M&L for 75 mm thick Cement concrete type C2, 1:3:6 (40mm graded aggregate) finishing the surface even and smooth without using extra cement complete all as specified and directed.
39S&F 125X60 mm size of Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and as directed.
40M&L for plain cement concrete Type C1, 1:3:6 (using 20 mm graded aggregate) for filling of hollow pressed steel frame complete all as specified and directed.
41M&L for plain cement concrete Type B-0 1:2:4 (using 12.5 mm graded stone aggregates) for fixing hold fast including repairing of disturbed plaster (while taking down door/window,ventilator frame) and matching the repaired surface with existing one complete all as specified and directed.
42S&F 25 x 3mm FI hold fast conforming to Fe 290, Gde -E-165 complete all as specified and directed.
43S&F 35mm thick second class hardwood factory made flush shutters, solid, core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.
44S&F 35 mm thick second class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass gauge etc. wihout sash bars sizes of the members of the shutters as specified in SSR Part-I section 8 , clause 8.24 (a) complete all as specified and directed.
45S&F Solid PVC Double door frame of size 50mm x 95mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet reinforced with M.S. tube, supplying & fixing in opening as per specification & drawing specified and directed.
46S&F 28 to 30mm thick Factory Made Solid PVC Moulded Door Shutter, particle board (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.
47S&F 100 mm butt hinges, cast brass,with mild steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and directed.
48S & F 150 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.
49S&F 150 mm long aluminum anodized barrel tower bolts of extruded section complete all as specified and directed.
50S & F 300 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed complete all as specified and directed.
51S & F Aluminium door stopper of size 150 mm long double legged fixed to bottom rail of door shutter provided with rubber bushing at one end to stop the door at floor and other end provided with aluminium plate base fixed with door shutter with screws at appropriate height complete all as specified and directed.
52S&F MS 300mm helical door springs including roller and roller plate complete all as specified and directed.
53S&F aluminium powder coated ventilators partly fix and partly louvered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc complete all as specified and directed.
54Supply only liquid water proofing compound complete all as specified and directed.
55S & F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover complete all as specified and directed.
56S&F vitreous china squatting pan (Orissa pattern white) long pan fixed size 580x440mm white with integral footrest with 100 mm bore Cast iron `P' or `S' trap complete (excluding flushing cistern and flush pipe) complete all as specified and directed.
57S&F PVC valveless syphonic action type flushing cistern 10 ltrs capacity low level, white with inlet ball valve, float and handle including brackets flush pipe of polythene of low or high density of PVC 32mm dia for low level cistern complete all as specified and directed.
58S&F vitreous china urinal, Half stall type white, with grating and union etc complete all as specified and directed.
59S&F vitreous china white counter oval shape wash hand basin of size 630x450mm including brackets complete all as specified and directed.
60Supply and fix swan neck long body 15 mm bore CP pillar taps, fancy type, cast copper alloy with capstan heads screwed down high pressure with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed.
61S&F chromium plated brass urinal spreader any size and description for fixing with necessary screws and bracket complete all as specified and directed.
62S&F tubular towel rail 20 mm dia 'D' type 600mm long of stainless steel complete all a specified and diredted.
63S&F 4 mm thick looking mirror of selected quality glass, without mounted on 6mm thick AC building board or commercial plywood or PVC and fixed to wall with chromium plated brass/aluminum screws and cup washers complete all as specified and directed.
64S&F brass chromium plated, 15 mm bore health faucet, (flexy type) min 1.00 mtr long complete all as specified and as directed.
65S&F brass chromimum plated two way bib cock fancy type, 15mm bore complete all as specifed and as directed.
66S&F angle stop valves 15mm bore, fancy type chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.
67S&F 15mm bore PVC connection with PTMT nuts of length 450mm complete all as specified and directed.
68S&F brass chromium plated bottle trap for wash basin/sink with inlet and outlet screwed for pipe or connections including necessary packing, union and cap bore of trap 32mm fixed complete all as specified and directed.
69S&F waste coupling brass CP for glazed ware sink, WHB etc with long screwed shanks and fly nuts complete of 32mm dia.etc. complete all as specified and directed.
70S&F 15mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors complete all as specified and directed.
71S&F 20 mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors complete all as specified and directed.
72S&F 1000 Ltrs capacity rotational moulded polythene water storage tank ISI marked (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.
73S&F 20mm bore ball brass valve, high pressure with polythene float & fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.
74S&F 20mm bore Gun metal gate valve with iron wheel head screwed both end for iron pipe complete all as specified and directed.
75S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified.
76S&F PVC (SWR) pipes single socketed in any length with rubberring joints fixed to walls 75mm bore complete all as specified and directed.
77S&F 110mm bore PVC (S.W.R) bend with access door complete all as specified and directed.
78S&F 110mm bore PVC (SWR) branch piece, single `Y’ equal or un equal with access door complete all as specified and directed.
79S&F 75mm bore PVC (S.W.R) bend with access door complete all as specified and directed.
80S&F 110mm bore PVC vent cowl complete all as specified and directed.
81S&F PVC floor trap 75 mm dia with CP gratings complete all as specified and directed.
82S&F PVC nahani trap 110 mm dia with CP gratings complete all as specified and directed.
83S&F toilet paper holder fixed to walls with brass chromium plated (CP) brass screws complete all as specified and directed.
84S & F PVC waste pipe 32 /40 mm dia x 600 mm long complete all as specified and directed.
85Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall complete all as specified and directed.
86Preparing new surfaces of ceiling and applying three coat of white wash complete all as specified and directed.
87M&L for preparation of newly plastered surfaces of wall and applying two coats enterior emulsion over a coat of primer and avg 3 mm thick wall care putty complete all as specified and directed.
88Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10 sqm over and avg 3 mm thick wall care putty on new surfaces complete all as specified and as directed.
89Material & Labour for painting two coats with synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10cm width or girth including preparation of surfaces complete all as specified and directed.
90Preparation of new or previously un-treated wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.
91Returning, filling in, including spreading levelling watering and well ramming in layers nexc 25cm as in hard/dense soil complete all as specified and directed.
92Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed in hard/dense soil complete all as specified and directed.
93M&L for anti-termite Treatment of soil under floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12 mm dia holes with CM 1:2 to match the floors complete all as specified and directed.
94M&L for anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @2.25 litres per linear meter including drilling and plugging holes etc.in apron complete all as specified and directed.
95M&L for 150 mm dia reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.
96Material & Labour for concrete bed to 150 mm bore drain pipes in cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.
97M&L for 15mm thick rendering on fair faces of brick surfaces in CM (1:6), finished surfaces even and smooth without using extra cement complete all as specified and directed.
98M&L for PCC 1:2:4 type B2 using 40 mm graded stone aggregate as in surface channel & drain complete all as spacified and directed.
99Extra over surface channel inside of manholes for forming fair finished drains of channels 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends, complete all as specified and directed. (Inner girth only be measured and paid), complete all as specified and directed.
100Surface excavation not exceeding 30 cm deep and averaging 15 cm deep in soft/ loose soil and getting out including clearing all grass vegetation, saplings, shrubs, brush woods under growth roots and trees exceeding 30 cm girth, complete all as specified and directed.
101Removing excavated material hard/dense soil not exc 50 m deposited where directed at a level n.exc 1.5 m above the starting point for soil, complete all as specified and directed.
102M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.
103M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base, complete all as specified and directed by engineer-in-charge.
104Material and labour for pre-cast cement concrete type B1 1:2:4 (20mm graded aggregate) as in kerb stone (factory made) on road and path including exavating in line n.exc 20cm in width and 30cm deep with 50mm thick PCC 1:4:8 in sub base of excavated area lay/fix the curve stone over PCC and packing the same duly retuning filling and pointing the gaps between curve stones with grey cement complete all as specified and as directed
105M&L for 60mm thickness machine pressed pre-cast concrete interlocking paver block any size and shape confirming to IS 15658-2006, M-30 grade with grey cement and no pigment, laid over 50mm thick sand cushion and including joints filled with sand, complete all as specified and directed.
106M&L for PCC (1:2:4) type B-1 (20mm graded aggregate) as in kerbs/coping and the like including weathering, slightly rounded or chamfered angles and throating, including formwork complete all as specified and directed
107Excavating in post holes (or similar holes) in Hard/dense soil each n exc 0.5 cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed
108S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed by Engineer-in-charge.
109S&F steel Plates (plain or chequered)channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W(Gde-E-250) quality-A complete all as specified and directed by Engineer-in-charge.
110S&F 5 to 10 mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed.
111S&F mangalore pattern pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.
112S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.
113S&F MS steel flat iron as in wind tie for roof sheet including securing bolts complete all as specified and directed.
114Material and labour for point wiring (concealed) for light point in and including rigid non-metallic PVC heavy duty conduit, 19/ 20 mm dia suitable size including cutting chases for conduits, sinking for boxes for concealed conduit wiring with 1.5 sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cable single core, 1100 volts grade for fixing moudular flush type metal boxes suitable for fixing modular switches, sockets and fan regulator etc., including PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm as an earth wire connected to common earth and earth dolly as per IS specification and as specified in SSR Part-I complete for one light point /fan/ bell/ buzzer controlled by one modular switch, 1 way 6 amps, 1 module complete and all as directed.
115All as per item No. 114 here-in-before but with one 3 pin, 5 amps socket outlet on independent board.
116All as per item No. 114 here in before but with 2.5 sqmm copper conductor cable for one 3 pin, 15 amps socket out let on independent board.
117All as per item No. 114 here-in-before but with 4 sqmm and 4 sqmm as earth conitnuty conductor
118M&L for sub main wiring with two single core, multi stranded, PVC insulated, 1100 Volt grade, FRLS, cable with copper conductor of size 6 Sq mm in and including/drawing through rigid non metalic PVC conduit medium grade, ISI marked, 25 mm dia for sub main wiring including continuous PVC insulated copper conductor single core earth continuity conductor of size 6 Sqmm connected common earth dolly complete all as specified and directed. Note:- 2x 6 Sq mm conductor cable, 1 x 6 Sq mm conductor earth continuity cable & PVC conduit shall be measured as one unit length
119Supply and fix modular switch type 230/ 250 volts, 6 amps, 1 module, single pole, one way, complete all as specified and directed.
120Supply and fix modular socket out let multi purpose 2 in 1, 2/3 pin, 6 amps, flush type, ISI marked complete all as specified and directed.
121Supply and fix switch modular 16 amps, flush type, ISI marked complete all as specified and directed.
122Supply and fix modular socket 2/3 pin combined, 6/16 amps, flush type, ISI marked complete all as specified and directed.
123Supply and fix sheet metal enclosures for SPN with two pin and earth plug and socket with one single pole MCB 20 amps complete all as specified and directed.
124Supply and fix ceiling rose surface bakelite, three terminal complete all as specified and directed.
125Supply & fixing round shape 12 Watts 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holder , LED Lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.
126Supply and fix LED light fitting 1 x 18Watt, 220V, AC decorative box type with driver, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all fixing arrengenment complete all as specified and directed.Note:- The LED batten and LED tube rod shall be of same make.
127Supply and fix LED street light 35/36 W IP 65 complete all as specified and directed.
128Supply and fixing ceiling fan complete with blades, down rods, electronic regulator and accessories, 20 volts, 1200 mm sweep. Min air delevery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.
129Supply and Fixing Sheet metal enclosure for DBs when MCBs to be Used, 4 way, VTP & N, double door type, 440 Volt with 200 amps rated busbar suitable for MCCB 4 pole incomer complete all as specified and directed.Note : MCBs will be Measured separately.
130Supply and Fixing Sheet metal enclosure for DBs when MCBs to be Used, 8 way, SPN, double door type, 240 Volt with 200 amps rated busbar complete all as specified and directed.(Note : MCBs will be Measured separately)
131Supply and Fixing Sheet metal enclosure for DBs when MCBs to be Used, 4 way, SPN, double door type, 240 Volt with 200 amps rated busbar complete all as specified and directed.Note : MCBs will be Measured separately.
132Supply and Fixing MCCB, four pole, 100 Amp, 415 Volt, of breaking capacity 16 KA complete all as specified and directed.
133Supply and fix MCB, SPN, 240 volts, 40 amps capacity, 'C' series complete all as specified and directed.
134Supply and fix MCB, SP, 240 volts, 5 to 32 amps capacity, 'C' series complete all as specified and directed.
135M & L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length fo drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.
136Supply and fixing of exhaust fan, steel body AC single phase. 230 V of size 300 m sweep with blades and frame and louvers and including making of holes in wall, floor etc complete all as specified and directed.
137Supplying and installing steel body desert cooler electric driven (single phase), having nominal air flow capacity of 4000 Cum per hour (or nearest size) complete all as specified and directed.
138Supply and lay pipe galvanized, “Heavy class”, including fittings, 20 mm (1”) dia with all fitting such as elbow, funnel, socket, reducer, pipe cutting and nipple as required at site complete all as specified and as directed.
139Supply and lay pipe galvanized, “Heavy class”, including fittings, 15 mm (1/2”) dia with all fitting such as elbow, funnel, socket, reducer, pipe cutting and nipple as required at site complete all as specified and as directed.
140Supply and fixing of gun metal,globe or gate valves of size 20 mm, with iron wheel head,screwed both ends for iron pipe and fixed.
141Supply and fixing of gun metal,globe or gate valves of size 15 mm, with iron wheel head,screwed both ends for iron pipe and fixed.
142M&L for construction of masonry valve pit with the following specification:- Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 900 x 900x900 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mmx40mmx5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and two coats of synthetic enamal paint and preparation of surfaces complete all as specified and shown on drawing.
143Cutting existing steel tubing of 20 mm pipe for alteration or additions complete all as specified & directed.
144Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core cable complete all as specified and directed
145Excavation in trenches not exceeding 1.5m in width and not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and directed
146Supply & laying dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trench complete all as specifieds and directed.
147M & L for unreinforced precasted concrete cable cover class LV, type 1,flat , size 250mm x 150mm x 40mm complete all as specified and directed
148Material and labour for GI pipe ''light grade'' for road crossing / on wall / on pole with fixed clamps, nuts, bolts for cable protection of size 40 mm dia complete all as specifieds and directed.
149Schedule of credit amount of Rs 0.00 to be deducted during AOC. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58581866
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 43.59 Lakhs
LAST DATE 09-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for Provn Of 02 X Addl Class Rooms Alongwith Allied Infra Near Chanakya Block At Mcmm Jabalpur
Basic Detail
Tender No 8944/E8
Bidding Type Tender
Location
City Jabalpur
State Madhya Pradesh
Key Dates
Publish Date 18 Nov 2026
Submission Date 09 Dec 2026
Open Date 14 Dec 2026
Finance
Tender Value 43.59 Lakhs
Tender Fee 500
EMD 87180
Exemption Available
Document List
5900979b-8544-4877-aa00-1d7807898bc8.html
BOQ_896714.xls
TENDER8944.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 18, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 09, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 18 days
Dec 14, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 23 days

Tender Documents

Download All (ZIP) ↓
html

5900979b-8544-4877-aa00-1d7807898bc8.html

xls

BOQ_896714.xls

pdf

TENDER8944.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender