Tender For Special Repair To Ug Sump No.02 & Pump House At Kr Bk Under Ge (South) Bangalore.
Tender Value
37.86 Lakhs
Estimated cost
Bid Submission
08 Dec 2026
16 days left
EMD
75720
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bengaluru Urban → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Ug Sump No.02 & Pump House At Kr Bk Under Ge (South) Bangalore.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or stone walls or concrete ceiling etc, incl raking out joints, hacking for key scrubbing down with water, etc. complete all as specified and directed. |
| 2 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3.0kg of cement per sq metre |
| 3 | Surface preparation by removing loose concrete by gentle chipping until the hard concrete is exposed leaning of exposed surface thoroughly with air /water jet to get solid surface of walls, ceiling etc. |
| 4 | M&L for Ready mix concrete (design mix), M-30 grade in foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slabs, underreamed piles, flooring and mass concrete complete all as specified and as directed. |
| 5 | M&L for Cleaning the existing reinforcement with hammer tapping and wire Brush/ rotary wire brush, fixed to hand drill machine, making the surfaces free form loose corrosion material, dirt scalling etc. complete. Applying two coats of polymer based alkaline rust converting primer confirming to ASTM-B 117 by means of paint brush, liberally all over in two coats of 1 hour between the costs, The product should converts the rust in to stable organo metallic complex molicule layer, this should also act as primer to further treatment of steel etc. complete. The work should be carried out with all the safety belt and adequate labour insurance under the supervision of qualifed supervisor etc. complete. |
| 6 | Providing and applying Epoxy Phenolic Based anti-corrosive coating in 2 coats with time interval of minimum 6 hours. The coating shall have ECorr value of -45 mV against SCE in 3.5 NaCL for 100 hours and electrochemical evaluation of max 0.5 mA /cm2. This coating shall be applied over coated rebars. Coated rebars are aloowed to be cure in air for Minimum 48 hours oras per manufacturer’s specification as direction of Engineer in-charge. |
| 7 | Providing and applying concrete penetrating, migratory bipolar corrosion inhibitor conforming to ASTMG-109) by brush/spray with dosage of 4 Sqm/ ltr, over the entire chipped off / exposed concrete area including material, equipment, labour etc. complete in order to arrest further corrosion of reinforcement bars. The application of Bipolar corrosion inhibitor should reduce the corrosion in terms of coulombs by 30% minimum upon migration through the embedded side of concrete as measured. |
| 8 | S&F Welded steel wire fabric complete to concrete using concrete nails weigh n exc 4 Kg per sqm. |
| 9 | M&L for Providing 50mm thick (average) ready to use polymer modified mortar in two layers on the exposed concrete surface sandwiched by a layer of weld mesh fixed to concrete using concrete nails. Note - Weld mesh shall be measured and paid seperately. Speciality Coatings Pvt. Ltd. |
| 10 | Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface as per directed and complete. |
| 11 | Providing and applying High strength, free flow microconcrete of M50 Grade whereevere required with required shuttering. Dry density of material should be 1900 Kg-2000 Kg per cum. No mixiing of aggregate /cement should be allowed. For more than 100 mm thickness 15-20% baby chips of <15 mm can be addedd. |
| 12 | M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with liquid water proofing compound incl finished even and smooth without using extra cement complete all as specified and directed.Note-WPC shall be measured and paid seperately |
| 13 | M&L rendering 5 mm thick on fair faces of brick work or concrete surfaces of ceiling in cement mortar 1:3 incl finished even and smooth (without using extra cement). |
| 14 | PU Foam and PU Plain Injection (Active Leakage):Supply and apply of 1 component Polyurethane Injection, Dr. Fixit PU Foam Injection and 2 component Dr. Fixit PU plain injection as per the site condition of M/s Pidilite Industries Ltd; a low viscosity, hydrophobic polyurethane resin. The product when mixed & reacts with water foams instantly to 30-40 times its volume. The PU foam or PU plain injection system is injected in the concrete substrate under pressure using a suitable grouting pump. Storing & application to be done strictly in accordance with manufacture's methodology. Applicator to ensure complete surface preparation of concrete substrate prior to application. This including removing and packing of NRV Packers complete. Mode of measurement will be actual area treated. |
| 15 | Epoxy Injection Grout application (No active leakage): Providing and grouting with two component low viscous Moisture Insensitive Epoxy Injection Grout Dr. Fixit Epoxy Injection Grout or an approved equivalent to strengthen the structure at cocrete cracks. The material having mixing ratio - (Base : Hardener) - 100:60 (by weight) at the rate of 0.50kg/nozzle, which gives compressive strength of 70MPa in 7days as per BS6319:part 2, Flexural strength of 30MPa in 7days as per BS6319:part 3, Tensile strength of 15MPa in 7days as per BS6319:part 7, epoxy resin based injection grout meets the requirement of BS 6319 & ASTM C 881. The finished cost to include surface preparation, fixing of non-return valve injection packers of 10 or 12 mm dia at concrete cracks, seal the nozzles with polyester resin anchor grout Dr. Fixit Instant leak plug 0.2kg/nozzle. All the application procedure shall be as per the direction of the Engineer In charge. |
| 16 | Providing injection grouting low viscosity (3-5 cps) high molecular weight monomer APCOREP INJECTION GROUT LV into concrete by injection grouting at 400-500 mm centre to centre through nylon nipples of 12 mm dia fixed and drilled to the depth of 75mm to 120 mm, Injected into drilled holes at 4-6 kg /cm2 pressure and having tensile strength of >30 N/mm2 (ASTM-D-638-95) & flexure of >50 N/mm2 (ASTM-D-790-96). Injection Nipples to be placed and grouted with Apcorep EpoxySeal. Mixing Ratio : 1:1 (Base: Hardener) by Weight Compressive Strength - >70 Mpa at 7 Days (Assuming 0.2kg consumption of epoxy) sketch and directions of Engineer-in- charge.Note - Rate inclusive of drilling holes and nozle fixing, closing holes etc complete. |
| 17 | M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces mixed with integral water proofing compound as per manufacturer's instructions, surfaces finished even and smooth without using extra cement including dismantling existing water proofing treatment any type and any thickness from top surface of RCC roof slab and removing the materials outside defence land complete all as specified and directed.(Note:- Water proofing compound shall be measured and paid separately as supply only under relevant item of this schedule) |
| 18 | Preparing the new plastered surface of roof, removing the dust and laitance etc, Apply one coat of polymer based priming bond coat 1:4:7 (polymer, water and cement) to seal all the pores on the treated surface. Lay 45GSM glass fibre mesh or geo textile on the primed surface while it is in tacky condition. Apply two coats of PU RoofKoat/Davko K10 of approved shade on the Glass Fibre Mesh with a gap of 3-4hrs between the coating complete all as specified and as directed. |
| 19 | Providing and applying two coats of CFTRI Approved food grade epoxy with consumption of 350-400 g/sqm. |
| 20 | M&L for preparation of new plastered surfaces of walls including and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 21 | M&L for 75 mm thick, PCC 1:3:6 type C1 (using 20mm graded stone aggregate), finished even and and fair as in plinth protection incl joints filling complete all as specified. |
| 22 | S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 23 | M&L preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide. |
| 24 | Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) incl staking serviceable material and removing debris outside MD land complete all as specified and directed. |
| 25 | M&L 75 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded crushed stone aggregate), as in sub base of floors complete all as specified and directed. |
| 26 | M&L Machine Pre cast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-40 grade with grey cement and pigment as in ramps/Hardstandings complete all as specified and directed. |
| 27 | M & L for coloured vitrified heavy duty ceramic scratch and stain resistant external tiles of size 40cm x 40cm x 12mm thick laid over and including 15mm thick CM 1:4 set jointed and pointed in neat cement slurry in floors complete all as specified and as directed. |
| 28 | Removing building materials / waste material/ debri beyoned the distance of 1.00 KM distance incl loading unloading and stacking or levelling including raising/lowering complete at the destination outside defence land all as specified and as directed. |
| 29 | Demolition of precast concrete articles and precast concrete block walling complete all as specified and as directed. |
| 30 | M&L Precast cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate ) as in block masonry with solid block, exc 10cm in width and setting in mortar 1:6 complete all as specified and as directed. |
| 31 | Supply only Liquid water proofing compound |
| 32 | Dismantling floor hearth/ stone slabs/mosaic tile flooring or wall tiling including cement mortar bedding (but not backing) or plastering and removing servicebale tiles to stores and rubbish off the same out side the MD land complete all as specified and as directed. |
| 33 | M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl screed bed of 15mm thick in CM 1:6 etc complete all as specified and directed. |
| 34 | S&F coloured glazed ceramic tile in vertical surface 300x400x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering CM 1:4 backing coat complete all as specified and as directed. |
| 35 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm etc complete all as specified and directed. |
| 36 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm and exc. 4 Sqm etc complete all as specified and directed. |
| 37 | S&F Factory Made single extruded WPC (Wood polymer composite) solid door/windows and other frames / chowkats of size 45mm x 70mm single rebated comprising of virgin PVC polymer of K value 58-60 (SuspensionGrade) calcium carbonate and natural fibres (Wood powder/rice husk/wheat husk) and Non-toxic additives (Maximum toxicity index of 12 for 100 gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws withdrawal strength of 2200 N (Face) and 1100 N (Edge) minimum compressive strength of 58 N/Sq mm, modulas of elasticity 900 N/Sq mm and resistance to spread flame of Class A category with property of being termite / borer proof, water/moisture proof and fire retardant and fixed in position with MS holdfast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (MS holdfast/lugs or SS dash fastener shall be paid for separately) |
| 38 | S&F Factory Made single extruded WPC (Wood polymer composite) solid door/windows and other frames / chowkats of size 65mm x 100mm single rebated comprising of virgin PVC polymer of K value 58-60 (SuspensionGrade) calcium carbonate and natural fibres (Wood powder/rice husk/wheat husk) and Non-toxic additives (Maximum toxicity index of 12 for 100 gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws withdrawal strength of 2200 N (Face) and 1100 N (Edge) minimum compressive strength of 58 N/Sq mm, modulas of elasticity 900 N/Sq mm and resistance to spread flame of Class A category with property of being termite / borer proof, water/moisture proof and fire retardant and fixed in position with MS holdfast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (MS holdfast/lugs or SS dash fastener shall be paid for separately) |
| 39 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other double rebate Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length incl all necessary fittings complete as per direction of Engineer-in-Charge. complete all as specifed. |
| 40 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge. |
| 41 | S&F factory made PVC glazed door shutter of approved make, made out of extruded PVC sections/solid moulded panel, with provision of glass panel(plain/frosted) or wiremess, including glazing, all fixtures and fittings such as hinges, handles, tower bolts, screws, etc complete all as specified. |
| 42 | S&F Stainless steel butt hinges of size 100mm fixed Complete all as specified and as directed. |
| 43 | S&F in repairs 200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified. |
| 44 | S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 45 | S&F 150 mm size extruded aluminium alloy handles for doors fabricated type anodized complete all as specified. |
| 46 | S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded |
| 47 | Steel ventilator with top hung shutter including hinges, steel peg stay, complete |
| 48 | S & F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane |
| 49 | S&F 4mm thick figured glass pin headed type and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified. |
| 50 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 51 | Cutting chases, pinning in, stone concrete block or slabs wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth and removal of debris otside of MOD land complete all as specified. |
| 52 | S & F in repair of CPVC pipes 20mm all SDR 11 Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of pipe of 15 mm GI pipe complete all as specified. |
| 53 | S&F of 20 mm dia CPVC brass elbow complete all as specified and as directed. |
| 54 | S&F of 20 mm dia CPVC Brass Tee complete all as specified and as directed. |
| 55 | S&F of 20 mm dia female/male brass threaded adapter complete all as specified and as directed. |
| 56 | S&F of 15 mm CP extension nipple complete all as specified and as directed. |
| 57 | S&F in repairs 100mm dia PVC (SWR) floor/Nahani trap, plain with grating including solvent cement with dismatnling of old nahani trap with necessary PCC/ cement work complete all as specified and as directed. |
| 58 | S&F PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints laid in floors complete all as specified and as directed. |
| 59 | S&F PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints laid in floors complete all as specified and as directed. |
| 60 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) 'P' or 'S' trap including dismantling of old Water closet complete all as specifed and as directed. |
| 61 | S&F in repairs plastic water closet seat cover, White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifed and as directed. |
| 62 | S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with inlet ball valve and float including flush pipe, handle, bracket PVC short/long bendetc. complete all as specified and directed |
| 63 | S&F in repairs PVC connection 15 mm size , 60 cm long with PTMT adopter,check nuts and washer on both sides for cold water complete all as specified. |
| 64 | S&F in repair vitreous china wash hand basin, white, flat back size 550 x 400 mm including one number brass CP waste coupling, waste pipe 32 mm dia, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed. |
| 65 | S&F in repairs 2 way bib cock double handle with flange and all necessary fittings all as specified and directed. |
| 66 | S&F in repair, bib taps, brass, fancy type, long body, chromium plated for 15 mm bore pipe or for brass ferrule or to GI socket complete all as specified and directed. |
| 67 | S&F in repairs 15 mm nominal bore stop valves/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed . |
| 68 | S&F in repairs over head shower chromium plated 95 mm dia with 3 flow with SS over head shower arm of 180mm with flange complete all as specified and directed. |
| 69 | S&F in repair tubular towel rail 600 mm long of brass chromium plated 20 mm dia D type 60 cm long fixed with two plugs (gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws complete all as specified. |
| 70 | S & F in repairs looking mirror of 5 mm thick 500mmx700mm with double coat for protection and longevity grounded edges for safety and silver plating on the back for better refelection and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified & directed. |
| 71 | S&Fin repairs 15mm size health faucet, ABS body , with wall hook and 1 metre stainless steel braided rubber hose pipe complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 72 | S&Fin repairs 15mm size health faucet, ABS body , with wall hook and 1 metre stainless steel braided rubber hose pipe complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysDec 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender