Tender For Remodeling Of Lift Irrigation Scheme Patta Brawary In Gp Brawary, Tehsil & Distt. Solan (Sh:- Providing, Laying, Jointing, Testing & Commissioning Of Gi And Hdpe Pipes In Distribution System & Providing And Fixing Field Outlet Assemblies).
Tender Overview
Project Description
Tender for Remodeling Of Lift Irrigation Scheme Patta Brawary In Gp Brawary, Tehsil & Distt. Solan (Sh:- Providing, Laying, Jointing, Testing & Commissioning Of Gi And Hdpe Pipes In Distribution System & Providing And Fixing Field Outlet Assemblies).(Job No.-2)
BOQ
| Sl. No. | Item Description |
| 1 | Excavating trenches of required width for pipes, cables, etc including excavation in all kinds of soil such as pick work, jumper work, saturated soil including bailing & pumping out water, blasting soft / hard rock or chiselling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, levelling of beds to correct grade including shoring, strutting planking, timbering and dewatering wherever required, stacking the useable and unusable material/soil separately and after laying, jointing and testing of pipes returning the usable soil in trenches in 15cm layers including consolidating of such deposited layer by ramming and watering and then disposing of all surplus excavated soil/ unusable material as directed including carriage of material within all leads and lifts & to the entire satisfaction of Engineer in charge. |
| 2 | Pipes, cables etc. upto 80mm dia |
| 3 | Pipe Excavation 80mm-300mm Dia |
| 4 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches or drains etc upto all depths in all kinds of soil such as pick work, jumper work, soft & hard rock and through conglomerate rock upto all leads and lifts, stacking the excavated soil not more than 3m clear from the edge of excavation and than returning the stacked soil in 15cm layers when required into plinth side of foundation etc. consolidating each deposted layer by ramming and watering and then deposing of all surplus excavated earth in all leads and lifts including carriage of material complete in all respect & to the entire satisfaction of Engineer in charge. |
| 5 | Providing and laying in position cement concrete 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) & curing complete excluding cost of form work in foundation and plinth including entire carriage of material in all leads and lift complete in all respect & as per direction of Engineer in charge. |
| 6 | Providing and laying in position cement concrete 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size) & curing complete excluding cost of form work in foundation and plinth including entire carriage of material in all leads and lift complete in all respect & as per direction of Engineer in charge. |
| 7 | Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm.so as to give a fair finish including centering, shuttering, strutting and propping etc with wooden batens and ballies,height of propping and centring below supporting floor to celing not exceeding 4 mtrs and removal of the same for insitu- reinforced concrete & plain concrete work. |
| 8 | Foundations, footings, bases for columns |
| 9 | Laying, jointing, testing and commissioning of Plain ended GI (MG) pipe with circumferential butt welded joints wherever required by electric arc welding, (welding thickness shall be equal to pipe wall thickness) and testing of GI pipe of following diameters conforming to IS-1239-Part I latest with up to date amendments having wall thickness as specified below capable of withstanding required test pressure, including manufacturing & fabrication of reducers/tapers, all short pieces, bends etc as per site requirements made from parent tube in random length 4m-6m with plane end and jointed with MS flanges conforming to IS-6392-1971 or Latest with up to date amendments. The pipe end shall be bevelled suitable for butt welded joint including the cost of jointing with butt welding conforming to IS-816-1969 or latest amendments with electrode as per IS:814-1991 or latest with up to date amendments including required no and size of MS nuts and bolts as per IS:1369-1967 or latest with up to date amendments and compressed asbestos fiber, jointing gasket sheet not less than 3.00 mm in thickness as per IS:2712-1998 or latest with up to date amendments including 99% butt welded joint. The welding of flanges to be done on both faces in two layers on outer face & one layer on inner face to make the joint leak proof & to the entire satisfaction of Engineer in charge. The laying of pipe conforms to IS:5822-1994 or latest with up-to-date amendments & as per CPHEEO manual & will also include all operational such as cutting, welding and jointing including flushing, cleaning and hydraulic testing including carriage of material in all leads & lifts complete in all respect to the entire satisfaction of Engineer in charge. |
| 10 | GI-Medium Pipe of Dia 150 mm (Plane Ended) |
| 11 | GI-Medium Pipe of Dia 125 mm (Plane Ended) |
| 12 | Providing, welding and fixing of M.S. plate flanges conforming to following flange tables as per IS 6392-1971 (Latest with up to date amendments) and welding of MS flanges with GI pipes in three layers i.e two-layer on outer faces and one layer on inner faces to make the joint leak-proof (The cost of proving and laying of GI pipes and butt welded joints to be measured and paid for separately). The welding of flanges should conform to IS 816-1969 with electrodes as per IS 814-1991 and the required number of nuts and bolts conforming to IS 1364. The thickness of gasket not less than 3.00 mm conforming to IS 2712-1998. The work shall be done as per the entire satisfaction of the Engineer in charge with in all leads and lifts including carriage of material complete in all respect. |
| 13 | for GI (MG)pipe of 150mm Flange Table-5 |
| 14 | for GI (MG)pipe of 125mm Flange Table-5 |
| 15 | Laying, jointing with fusion welding process, testing & commissioning in trenches High-Density Polythene Pipes of following diameter & class conforming to IS:4984-1995 or latest with upto date amendments including all necessary fitting in all leads and lift to the entire satisfaction of the Engineer in charge.(Earth work in trenches to be measured & paid sepeartely). |
| 16 | 250 mm (Class- PE-80 PN-8.0) |
| 17 | 250 mm (Class- PE-80 PN-4.0) |
| 18 | 225 mm (Class- PE-80 PN-6.0) |
| 19 | 200 mm (Class- PE-80 PN-4.0) |
| 20 | 180 mm (Class- PE-80 PN-4.0) |
| 21 | 160 mm (Class- PE-80 PN-4.0) |
| 22 | 125 mm (Class- PE-80 PN-4.0) |
| 23 | 90 mm (Class- PE-80 PN-4.0) |
| 24 | 90 mm (Class- PE-80 PN-6.0) |
| 25 | 90 mm (Class- PE-80 PN-10.0) |
| 26 | 63 mm (Class- PE-80 PN-6.0) |
| 27 | 63 mm (Class- PE-80 PN-4.0) |
| 28 | 125 mm (Class- PE-80 PN-6.0) |
| 29 | 63 mm (Class- PE-80 PN-12.5) |
| 30 | Laying, jointing, testing and commissioning of Plain ended GI (MG) pipe with circumferential butt welded joints wherever required by electric arc welding, (welding thickness shall be equal to pipe wall thickness) and testing of GI pipe of following diameters conforming to IS-1239-Part I latest with up to date amendments having wall thickness as specified below capable of withstanding required test pressure, including manufacturing & fabrication of reducers/tapers, all short pieces, bends etc as per site requirements made from parent tube in random length 4m-6m with plane end and jointed with MS flanges conforming to IS-6392-1971 or Latest with up to date amendments. The pipe end shall be bevelled suitable for butt welded joint including the cost of jointing with butt welding conforming to IS-816-1969 or latest amendments with electrode as per IS:814-1991 or latest with up to date amendments including required no and size of MS nuts and bolts as per IS:1369-1967 or latest with up to date amendments and compressed asbestos fiber, jointing gasket sheet not less than 3.00 mm in thickness as per IS:2712-1998 or latest with up to date amendments including 99% butt welded joint. The welding of flanges to be done on both faces in two layers on outer face & one layer on inner face to make the joint leak proof & to the entire satisfaction of Engineer in charge. The laying of pipe conforms to IS:5822-1994 or latest with up-to-date amendments & as per CPHEEO manual & will include all operational such as cutting, welding and jointing including flushing, cleaning and hydraulic testing complete in all respect to the entire satisfaction of Engineer in charge including entire carriage of material up to all leads and lifts. |
| 31 | GI-Medium Pipe of Dia 100 mm pipe plane ended thickness of pipe =4.50 mm |
| 32 | GI-Medium Pipe of Dia 65 mm pipe Screw & socketed thickness of pipe =3.60 mm |
| 33 | Providing and fixing cast iron sluice valve (with hand wheel) as per IS:780-1984/IS:14846-2000 class-I or latest with up to date amendments up to 300mm dia including cost of brass spindle & as per IS:2906-1984 class-II or latest with up to date amendments for dia <300mm complete with nuts and bolts, rubber insertion etc (tail piece if required shall be measured and paid for separately) complete in all respect as per the direction of Engineer in charge. |
| 34 | 40mm Gun Metal Valve |
| 35 | 65 mm Gun Metal Valve |
| 36 | 80 mm Gun Metal Valve |
| 37 | 100 mm Gun Metal Valve |
| 38 | Providing & fixing of GI fitting |
| 39 | 65Ø G.I. pipes Elbow |
| 40 | 65Ø X 40Ø G.I. Reducer |
| 41 | 40Ø G.I. pipes Tee |
| 42 | 40Ø G.I. pipes nipple(6\\" Length) |
| 43 | 65Ø G.I. Tee |
| 44 | 80Ø G.I. pipes Elbow |
| 45 | 80Ø X 65Ø G.I. Reducer |
| 46 | 65Ø G.I. pipes Tee |
| 47 | 65Ø G.I. pipes nipple(6\\" Length) |
| 48 | 80Ø G.I. Tee |
| 49 | 125Ø G.I. pipes Elbow |
| 50 | 125Ø X 80Ø G.I. Reducer |
| 51 | 80Ø G.I. pipes Tee |
| 52 | 80Ø G.I. pipes nipple(6\\" Length) |
| 53 | 125Ø G.I. pipes Tee |
| 54 | 150Ø G.I. pipes Elbow |
| 55 | 150Ø X 100Ø G.I. Reducer |
| 56 | 100Ø G.I. pipes Tee |
| 57 | 100Ø G.I. pipes nipple(6\\" Length) |
| 58 | 150Ø G.I. pipesTee |
| 59 | 200mm Ø pipes Elbow |
| 60 | 200Ø X 100Ø Pipe Reducer |
| 61 | 100Ø G.I. pipes Tee |
| 62 | 100Ø G.I. pipes nipple(6\\" Length) |
| 63 | 200Ø pipesTee Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender