Defence Statutory Bodies & Commissions/Committees Closing in 17 days TDR #58579507

Tender For Repair To Fencing, Compound Wall, Drain And Certain Misc Work At Tech Area Of Kaluchak And 23 Wing Under Ge (Af) Jammu

Issued by Statutory Bodies & Commissions/Committees · Jammu, Jammu and Kashmir
Tender Value
30 Lakhs
Estimated cost
Bid Submission
08 Dec 2026
17 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Repair To Fencing, Compound Wall, Drain And Certain Misc Work At Tech Area Of Kaluchak And 23 Wing Under Ge (Af) Jammu

BOQ

Name of Work:- REPAIR TO FENCING, COMPOUND WALL, DRAIN AND CERTAIN MISC WORK AT TECH AREA OF KALUCHAK AND 23 WING UNDER GE (AF) JAMMU
Sl. No. Item Description
1M&L 100 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone agg as in ,floors and Pavings etc, finished even and smooth w/o using extra cement including demolition of PCC Complete all as specified and directed by Engineer-In-charge.
2M&L Cement concrete 1:3:6 type C2 using 40mm graded stone crushed aggregate in plinth protection, 75mm thick, finished even and smooth using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight, complete incl demolition of existing unserviceable plinth protection Complete all as specified and directed by Engineer-In-charge.
3M&L for cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation Mass concrete as in manhole sub base,drain subbase, and same nature of work etc , incl demolition of existing unserviceable subase, Complete all as specified and directed by Engineer-In-charge.
4M&L for coloured anti skid ceremic tiles 7 to 8 mm thick area of each tiles exc. 0.11 sqm and n. exc. 0.18 sqm (400 x 400 mm joint free (rectified) ) as in floor set & jointed in neat cement slurry and pointed in white /coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete incl dismantling of existing tiles/flooring and remove demolished matreial to out side MoD land Complete all as specified and directed by Engineer-In-charge.
5Ditto all as per item no.4 above but in dado / skirting etc. over and including 10 mm thick rendering in CM (1:4) Complete all as specified and directed by Engineer-In-charge.
6M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, incl demolition old existing paver block/chequered tiles and remove demolised matreial/debries out side MoD land complete all as specified and directed by Engr-in-charge.
7M&L chequered cement concrete coloured tiles machine pressed conforming to IS 13801:1993 and , size not less than 300mm x 300mm (Approx), thickness 25mm,made by table vibratory method using PU mould, as in floor, paving set and jointed in neat cement to match with gray pigment including screed bed or bedding layer in CM 1:6 finished fair and even for laying floor finishes/tiles incl demolition old existing paver block/chequered tiles etc remove demolised matreial/debries out side MoD land complete all as specified and directed by Engineer-in-Charge.
8M&L 25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor and in surface channel finishes including finishing the surfaces even and rough without using extra cement, incl demolition of existing unserviceable subase complete all as specified and as directed by Engr-in-Charge.
9M&L for reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for slabs supported on wall, beams and columns, roofs, landings, balconies, canopies, deck slabs ,manhole cover ,drain cover and in shelves and the like , incl demolition of existing unserviceable reinforced cement concrete in any position, Complete all as specified and directed by Engineer-In-charge.Note : Reinforcement shall be measured and paid for separately.
10M&L for use and Formwork to sides of concrete foundations ,footings , columns , raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work Complete all as specified and directed by Engineer-In-charge.
11M&L for form work to sides and soffits of suspended slabs such as roof slabs, landings and similar work n.exc 200mm thick (horizantal or slopping) for flat fair finished surfaces, Complete all as specified and directed by Engineer-In-charge.
12Extra for forming fair finishing drain or channel 30 cm inner girth in cement concrete , using extra cement including forms, moulds etc Complete all as specified and directed by Engineer-In-charge.
13M&L for Steel reinforcement 10mm dia and over, TMT bars, cut to length, bent to shape required including, cranking, bending, spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, Complete all as specified and directed by Engineer-In-charge.
14M&L for steel reinforcement 6 to 8mm dia and over, TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, Complete all as specified and directed by Engineer-In-charge.
15M&L Cast iron work grade FG150, unmachined, inbrackets, gully traps,gratings, railing, frames,manhole covers, fire andsoot doors, dampers, stop valve boxes, gate stops,parts of ranges, balusters and similar articles Complete all as specified and directed by Engineer-In-charge.
16M&L Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, and including demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc complete all as specified and as directed by Engr-in-Charge.
17M&L for Brick work with sub class 'B' bricks, straight or curved on plan to any redius in half brick thick wall built in cement mortar 1:4, and including demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc complete all as specified and as directed by Engr-in-Charge.Complete all as specified and directed by Engineer-In-charge.
18All as per item no. 16 here-in-before but Excepet Bricks work with old size bricks, using old reuse bricks, as retrieved from dismantling of brick work under respective item, after removing mortar from and cleaning bricks; straight or curved on plan exc 6m mean radius, built in CM 1:6 Complete all as specified and directed by Engineer-In-charge.
19Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete including removal of all debris carryout from Mod land all as specified and directed by Engineer-in-Charge.
20M&L 10mm thick rendering on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:6 and applying three coats of white wash on new wall surface including preparation of surface., complete all as specified and directed by Engr-in-charge.
21M&L 15mm thick rendering on fair faces of brick work or concrete surfaces, other than fair face (without using extra cement) in cement mortar 1:4 including WPC @ 200ml per bag of cement complete all as specified and directed by Engr-in-charge.
22M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 sqm including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces as in camouflage pattern or as directed by Engr-in- charge, including preparation of surfaces of new walls etc Complete all as specified and directed by Engineer-In-charge.
23M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 sqm including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over old surfacesin camouflage pattern or as directed by Engr-in- charge, including preparation and complete removal of existing treatment of surfaces of old surfaces etc Complete all as specified and directed by Engineer-In-charge.
24M&L for applying two or more coat of Ist quality acrylic distemper (ready mixed) having VOC contents less than 50 gms/litre of approved manufacturer of required shade and colour complete as per manufacturer's specification, incl. preparation and complete removal of existing treatment of old surfaces of walls etc Complete all as specified and directed by Engineer-In-charge.
25S&F for reinforcement concrete pipes, class NP-2 laid and jointed complete with collars bore of pipe 450mm , fixed in cement mortar 1:3 including demolition and breaking up existing drain pipes complete all as specifiedand as directed by Engr-In-Charge.
26Removal of soil/silt, sludge,Shrubs and other waste from the drains to Wide and depth and cleaning thesurface throughly for free flow of rain watercomplete all as directed by Engr-In-Charge.Note : All sludge and waste matrial have carry out from this location out from Air Force sation.
27Dismanting of fencing wire mesh & barbed wire etc, Complete all as specified and directed by Engineer-In-charge.
28Dismantling wrought iron or mild steel work,frame work such as truss, wind tie, angle frame work , concertina coil of any description Complete all as specified and directed by Engineer-In-charge.
29Excavation in post holes (or similar holes) each n exc 0.5 cum, and removing surplus soil to distance n exc 50m and making good surface of any type of soil.Complete all as specified and directed by Engineer-In-charge.
30S&F Steel work in tubular trusses/purlins/posts (of round/rectangula/square hollow section) including angle cleats for jointing with welding confirming to IS.1161- 1979 grade St.-240, Complete all as specified and directed by Engineer-In-charge.
31S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick, trapozoidal pattern with guard film of any colour having tensile strength of 550 Mpa as in roof covering/cladding in wall, fixed with self tapping screws including dismantling old plain or corrugated asbestos sheeting , any gauge, thickness Complete all as specified and directed by Engineer-In-charge.
32M&L for MS work conforing to Fe-410-0 of Fe-310-0 Grade for fencing posts and struts in fencing and gate grill and grating including cutting bending top to shape as directed drilling holes matching for barbed wire etc. including all necessary drilling work complete and Complete all as specified and directed by Engineer-In-charge.
33Mild steel screw bolts (machine made) with hexagonal or square heads at one ends and screwed the other ends, or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut exc 5 cm long but n-exc 10cm, dia of shank 10 mm , Complete all as specified and directed by Engineer-In-charge.
34Supply only chain link MS Galvanised 4.0mm dia and 75mm pitch of wire fencing including line wires, and type to any type of standars, rails, straining bolts, etc. Complete all as specified and directed by Engineer-In-charge.
35Fixing only Chain link fencing including line wires, any mesh, size and type of standerds, rails, straining bolts,etc. including provission of binding wire Complete all as specified and directed by Engineer-In-charge.
36S&F MS round bars of 10mm dia in fencing for stiffening conforming to Fe-290,Gde -E-265
37Preparation of steel or iron surfaces of any description, over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer Complete all as specified and directed by Engineer-In-charge.
38Preparation of steel or iron surfaces of any description, n exc 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer Complete all as specified and directed by Engineer-In-charge.
39S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed non-magnetic with 2mm dia barbs at 75mm spacings and straining and fixing to any type of of standard rails straining bolts, including, securing or tying at crossings with and Provision of galvanised mild steel wire, stapples or steel pins, etc. as directed (each line wire to be measured) Complete all as specified and directed by Engineer-In-charge.
40Restraining & resecuring including making good & repairs galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed non-magnetic with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc Complete all as specified and directed by Engineer-In-charge.
41S&F concertina coil with punched tape of 600 mm dia , centre core wire shall be minimum 2.5 mm dia of mild steel wire conforming to IS 280-2006. Galvanised coating of steel concertina coil shall confirm to the requirements as laid down for medium coated wire in IS 4826 \\"Hot dipped galvainsed coating of round steel wires\\" conretina coil shall be fixed in diamond shape with the help of dovetail two handle and spikes shall be fixed at both end of coil,minimum straight length of the wire 150 RM of 10 RM of work ,minimum weight 13.5 Kg for 10 RM of work i.e. 90gm per RM of wire Complete all as specified and directed by Engineer-In-charge.
42Cleaning manually of blocked WC seat trap, inside house and gully trap it includes remove/refixing of grating and cleaning of WC's trap,kitchen/bath traps any type/pattern (pedestal/squatt pattern) upto 1st manhole and making the drain pipe of any size full functional by flushing with water to entire satisfaction of Engr-in-Charge including cleaning of 1st manhole and removing the waste material/sludge etc to out side form defence land complete all as directed by Engr-in-Charge.
43Cleaning of underground SGSW pipes of size 150mm dia by rodding from manhole to manhole or manhole to septic tank/well including taking off manhole cover and cleaning of manholes of any size and depth and removing waste material/sludge to out side form defence land complete all as directed by Engr-in-Charge.
44Cleaning and dewatering of septic tanks/pits of any depth incl let and outlet chamber and removing sludge (in solid and semi solid), silt, both organic and in-organic nature including any type of waste matterial after plugging of incomimg sewage line and removing waste material / sludge etc to out side form defence land and burrying the same in pit complete all as specified and directed by Engr-In-Charge.
45Removing of Sludge, mud from sewage sumpwell, manhole ,soakpit, sokage well of any depth incl inlet and outlet chamber (in solid and semi solid), silt, both organic and in-organic nature including any type of waste matterial/sludge with Mechaniclly or manual which are required on ground without any other financial effect removing waste material/sludge to out side form defence land complete all as directed by Engr-in-Charge.
46Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegetation upto and including roots upto 30mtrs hight form ground complete all as specified and directed.Note: This included any thick of plaster and already of tiles or mosaic tiles etc.
47M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) in foundations or in subbase including demolition of un-reinforced cement concrete in ground floor and paving any surface Complete all as specifed and directed by Engr-In-Charge.
48M&L for 25mm thick PCC type B-0, 1:2:4 (using 12.5mm graded aggregate in flooring finishing rough to recieveing Top layer for flooring including demolition un-reinforced cement concrete in ground floor and paving any surface complete all as specified and direted by Engineer in charge.
49M&L PCC 1:2:4 type B1 (Using 20mm graded stone aggregate )as in benching, bed plates, coping and the like including weathering, slightly rounded or chamfered angles as directed including necessary form work and finishing the surface even and smooth without using extra cement and including demolition un-reinforced cement concrete in ground floor and paving any surface complete all as specified and directed by Engr-In-Charge.
50Precast cement concrete type B-1, 1:2:4 (20mm graded crushed stone aggregate) as in manhole cover/drain cover set in CM 1:4 complete ( reinforcement shall be measured separately) all as specified incl form work cement including demolition/ dismentling reinforced/precast cement concrete of any depth complete all as specified and directed by Engr-In-Charge.
51M&L for joint free glazed ceremic tiles 300x250x7 mm or 450x350x7 mm thick, as in dado, vertical surfaces set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) , including dismantling floor, hearth or wall tiling including cement mortar and remove demoilshed material out side to defence land complete all as specified and directed by Engineer-in-Charge.Note - Design,colour shall be approved by GE/ User
52M&L for Joint free colored non skid ceramic tiles 7 to 8 mm thick, area of each tile exc 0.06 sqm but n exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement over and incl 15 mm thick screed bed in CM 1:4 to match Shade, pattern, laying etc of tiles, including dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing demolished material to out side defence land complete all as specified and directed by Engineer-in-Charge.Note - Design,colour shall be approved by GE/ User
53M&L for Joint free colored non skid ceramic tiles 7 to 8 mm thick, area of each tile exc 0.11 sqm but n exc 0.16 sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:4 to match Shade, pattern, laying etc of tiles including dismantling of existing unserviceable tiles including cement mortar bedding (but not backing) and removing demolished material to out side defence land complete all as specified and directed by Engineer-in-Charge.Note - Design,colour shall be approved by GE/ User
54M&L chequered or machine pressed cement concrete coloured tiles machine pressed conforming to IS 13801:1993 and ISI marked, size not less than 300mm x 300mm (Approx), thickness 25mm, as in floor, paving set and jointed in neat cement slurry and pointed in colored cement over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:4 to match Shade, pattern, laying etc of tiles, including dismantling of existing unserviceable tiles including cement mortar bedding (but not backing) and removing demolished material to out side defence land complete all as specified and directed by Engineer-in-Charge. Note - Design,colour shall be approved by GE/ User
55M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including dismentling of tile/Paver block complete all as specified and direted by Engineer in charge.
56Excavation in trenches in any type soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth in foundation etc for manholes, sewage line and getting out soil and remove out from defence land Complete all as specifed and directed by Engr-In-Charge.
57Returning filling in including spreading levelling , watering and well ramming in layers not exceeding 25 cm Complete all as specifed and directed by Engr-In-Charge.
58Cutting into existing manholes any size or any type for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed by Engr-in-Charge.
59M&L for 200 mm thick concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150/200 mm SGSW pipes including demolition of existing old pipes(salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specifiedand as directed by Engr-In-Charge.
60S&F for reinforcement concrete pipes, class NP-2 laid and jointed complete with collars bore of pipe 200mm , fixed in cement mortar 1:3 complete all as specifiedand as directed by Engr-In-Charge.
61S&F for Slat-glazed stoneware (SGSW) grade \\"A\\" drain pipes 200mm bore laid in trenches and jointed on concrete bed, complete including testing etc complete all as specified and shown in drgs(Concrete bed shall be measured and paid for separately).
62Extra for forming fair finishing drain or channel 30 cm inner girth in cement concrete , using extra cement including forms, moulds etc complete all as specified and direted by Engineer in charge.
63Providing and laying at or near ground level actory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and direted by Engineer in charge.
64M&L for 15mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed including taking up or down steel tubing complete to walls and ceilings or laid in floors complete all as specified and direted by Engineer in charge.
65Refixing only for 15mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed including taking up or down steel tubing complete to walls and ceilings or laid in floors complete all as specified and direted by Engineer in charge.
66M&L for 20mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed including taking up or down steel tubing complete to walls and ceilings or laid in floors complete all as specified and direted by Engineer in charge.
67Re fixing only 20mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floor complete all as specified and direted by Engineer in charge.
68M&L for cleaning and removing all scale and dirt, etc from water tanks of capacity exceeding 500 ltrs but not exceeding 1000 ltrs and from mouth of circulating pipes, etc including disconnecting, reconnecting & refixing water tanks in position complete all as specified and direted by Engineer in charge.
69S&F Rotational moulded polyethylene water storage tank, inner and out white, three layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes incuding dismantling 500 ltr water tanks and removing to store complete all as specified and as directed by Engr-in-Charge.
70S&F Rotational moulded polyethylene water storage tank, inner and out white, three layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes incuding dismantling 1000 ltr water tanks and removing to store complete all as specified and as directed by Engr-in-Charge.
71S&F PVC water tank cover suitable for 500/1000 Litre capacity including proper fixing with clamp &nut bolt complete all as specified and direted by Engineer in charge.
72S&F for in repair Angle valve cast copper alloy chromium Plated (CP) fancy type 15mm dia screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or for unions and fixed complete all as specified and direted by Engineer in charge.
73S&F for in repair CP Bib taps long nose, fancy type 15mm dia screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or for unions and fixed complete all as specified and direted by Engineer in charge.
74S&F in repairs Health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 Mtr long flexible tube and ABS Wall hook including making connections and fixed in position complete all as specified and directed by Engr-in- charge
75S&F Jet spary with one meter flexible tube 15mm dia for EWC including all connection complete all as specified and direted by Engineer in charge.
76S&F for repair toilet paper holder fancy type chromium plated screwed down for fixing to wall with screws complete all as specified and direted by Engineer in charge.
77S&F in repairs 10 ltrs capacity (PVC), valve less, syphonic action type, fluhsing cistern, low level, white, with inlet, ball valve, float and handle including brackets, PVC 32mm dia flushing pipe for cistren ete complete fixed in repairs complete all as specified and direted by Engineer in charge.
78S&F PVC (SWR) pipes single socketed in any length with rubber ring joints in trenches bore of pipe 110 mm with PVC clamps and saddles including taking down existing (SGSW/PVC) pipe and fittings.complete all as specified and direted by Engineer in charge.
79S&F in repair 110mm bore PVC (SWR) 'S or P' trap, including fixed with solvent cement complete all as specified and direted by Engineer in charge.
80S&F in reapir vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing of flushing cistern, brackets, flushing pipe, and CP jet spray including CP flexible pipe for EWC etc complete all as specified and direted by Engineer in charge.
81Vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding excluding connections to 'flushing cistern/pipe, 'Fixed in repair' complete all as specified and direted by Engineer in charge.
82S&F in repairs vitreous china urinal flat back 465x355x265mm size , including grating and Connection to flushing pipe and outgoing pipe complete all as specified and direted by Engineer in charge.
83S&F for in repair 15mm dia 450mm long PVC connection with PTMT nut and washer complete all as specified and direted by Engineer in charge.
84M&L with Tools grubbing up tree trunk including roots portion from wall /roof filling holes with PCC and making the surface finished with Cement plaster CM 1:3 upto 4th storey of Bldg complete all as specified and direted by Engineer in charge.
85M&L for removal of vegitation / trees grith exc 30cm n. exc 100cm from wall, roof top and CI/PVC sewer lines on wall upto height of 4th storey bldgs incl waste materials removing from site and area of removal places filling with PCC/CM 1:4 as site required,complete all as specified and direted by Engineer in charge.Note:- Contractor arrange his own suitable T&P as per site requirement and nothing extra shall be paid for the said work.PCC & CM 1:4 if any required will be measured and paid separately.
86Note:-i) All the complaint(s) received will be lodged & rectified by the contractor rep and will have to maintain a proper record as directed in complain register and in complain slip. (ii) Complain slip and complain register will be provided by the contractor without any extra charge.(iii) Complain register will be produced on daily basis to JE and Engr-in-charge (iv) The new items provided shall be measured and paid for separately under relevant items of Sch ‘A’.(v) If contractor fails to attend the complaints in 48 hours a recovery of Rs 200 shall recovered per complaint. (vi) Any Misc items reqd viz. colours, putty, Machenically Equipment which are required on ground etc in the work should be deemed incl in the respective items of works and nothing extra shall be paid on the account.
87SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58579507
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 30 Lakhs
LAST DATE 08-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for Repair To Fencing, Compound Wall, Drain And Certain Misc Work At Tech Area Of Kaluchak And 23 Wing Under Ge (Af) Jammu
Basic Detail
Tender No CA NO GE/AFJ-77/2026-27
Bidding Type Tender
Location
City Jammu
State Jammu and Kashmir
Key Dates
Publish Date 17 Nov 2026
Submission Date 08 Dec 2026
Open Date 15 Dec 2026
Finance
Tender Value 30 Lakhs
Tender Fee 500
EMD 60000
Exemption Available
Document List
BOQ_896547.xls
f88e8048-1427-46e4-84f0-0013ce43251f.html
Tender77.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 17, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 08, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 17 days
Dec 15, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 24 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_896547.xls

html

f88e8048-1427-46e4-84f0-0013ce43251f.html

pdf

Tender77.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender