Defence Statutory Bodies & Commissions/Committees Closing in 16 days TDR #58573147

Tender For Special Repair To Bldg No T-38 At Jhanger Base And Bldg No T-13 & 14 (Or Living) At Rumlidhara Under Age B/R Dett-A Of Ge 862 Ews

Issued by Statutory Bodies & Commissions/Committees · Rajouri, Jammu and Kashmir
Tender Value
44.38 Lakhs
Estimated cost
Bid Submission
08 Dec 2026
16 days left
EMD
88800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Rajouri → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Special Repair To Bldg No T-38 At Jhanger Base And Bldg No T-13 & 14 (Or Living) At Rumlidhara Under Age B/R Dett-A Of Ge 862 Ews

BOQ

Name of Work:- SPECIAL REPAIR TO BLDG NO T-38 AT JHANGER BASE AND BLDG NO T-13 & 14 (OR LIVING) AT RUMLIDHARA UNDER AGE B/R DETT-A OF GE 862 EWS
Sl. No. Item Description
1Schedule 'A' Part-I (B/R Works)Demolition of cement concrete (unreinforced) in ground floors and paving n. exc 15 cm th (below or above ground level), complete all as specified and directed. Note: No extra cost to be borne by govt in r/o flooring overleaped with tile incl screed .Thickness to be considered as total thickness of overleaping.
2Dismantling of plain or corrugated steel sheeting or any other type, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.
3Dismantling of existing false ceiling of any type etc, complete all as specified and directed.
4Taking down cement plaster on brick/stone or concrete surfaces including racking out joints hacking for key to any thickness scrubbing down with water etc, complete all as specified and directed. Note : No extra cost shall be borne by Govt exchequer for any no of layers over leaping of tiles/ mosiac finish.
5Taking down chowkhats with shutter (without taking off from shutter) n. exc 1.5 sqm each and removing to store, complete all as specified and directed.
6Taking down chowkhats with shutter (without taking off from shutter) exc 1.5 sqm and n exc 4 sqm each and removing to store and making good to surface disturbed due taking down, complete all as specified and directed.
7Taking down GI tubing of 15 mm dia and connection and including cleaning for refixing or removel, complete all as specified and directed.
8Taking down GI tubing of 20 mm dia and connection and including cleaning for refixing or removel, complete all as specified and directed.
9Dismantling of existing PVC water tank exc 500 litres and n.exc 1000 ltrs capaicty and removing to store, complete all as specified and directed.
10M&L for brick work in cement mortar (1:6) using old size sub class 'B' bricks in walling, straight or curved on plan exc 6m mean radius all as specified and including demolition of Brick/stone work built in cement morter of any descrption incl all necessary quions arches piilars etc, complete all as specified and directed.
11M&L for stone walling random rubble, uncoursed, well bonded bedded and solidly hearted, built in cement mortar 1:6 and including demolition of Brick/stone work built in cement morter of any descrption incl all necessary quions arches piilars etc, complete all as specified and directed.
12All as per Item No 11.00 here-in-before but except stone.
13Extra over stone walling, random rubble brought upto courses, for hammer dressing to face stones and dressing of face beds and joints, with maximum depressions on face from straight edge held against the dressed surface not exc. 40 mm on lime or sand stone, complete all as specified and directed.
14M&L for formwork to sides and soffits of floor or roof beam, beam hunching, girders, lintel, cantilevers, shelves including suports, overhangs etc, complete all as specified and directed.
15M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) for Beams, cantilevers, bressumers, lintel over 1.5 m span, icluding demolition of Reinforced cement Concrete in Roofs, floors ( other than ground floors), beams, staircases, landings, chajjas, lintel band and similar suspended works.(reinforcement cut as required to facilitate demolition), complete all as specified and directed.
16M&L for mild steel TMT bars 10mm dia and over, cut to length, bend to shape required, including cranking ,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.
17All as per Item No 16.00 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders.
18S&F mild steel as in Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. confirming to Fe 290 (grade E-165). (cut to ordinary lengths i.e. within 20mm of the length indicated), complete all as specified and directed.
19Erection and fixing only steel work in main and cross beams jack rafters, purlines where connected to common rafters and running rails and fixed with angle cleats or other connecting plates complete confirming to IS 1161-1979 grade St-240, complete all as specified and directed.
20S&F plates (plain or chequered ) channels square cut or notched oridinary or counter sunk forming holes w/o any attatchment confirming to Fe-290 grade-165, complete all as specified and directed.
21S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other,or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long, dia of shank 11 to 15 mm, complete all as specified and directed.
22S&F pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50mm thick of approved colour (multi colour pattern as approved by GE) having tensile strength 550 MPa as in roof covering/ cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed. Note : No extra cost shall be borne by Govt exchequer in r/o colour, pattern, etc.
23S&F pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of approved colour (multi colour pattern as approved by GE) having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.
24S&F 4mm thick designer ceiling board (Make \\" Everest/ Ramco/ Gyproc\\" Hill & Lake Pattern) in ceiling fixed with screw as per manufacturers instructions , laid on hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet & of size 24 x 32 x 300 mm spaced at 12 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be grater than 450 mm from adjustacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturction, complete all as specified and directed.
25All as per Item No 24.00 here-in-before but except material. Note : Ceiling boards dismantled from item No 03 shall be stored carefully without any damages and reused as refixing if contractor damages ceiling board intentionally then recovery of damaged boards shall be carried out.
26M&L for 15mm thick rendering on fair faces of brick surfaces finished even and smooth without using extra cement in cm 1:4, complete all as specified and directed.
27M&L for 15mm thick rendering on brick or concrete surfaces in cm 1:6 finished even and smooth without using extra cement, complete all as specified and directed.
28M&L for rendering 20 mm thick plastering on stone masonry surface in CM (1:6) and rendering is to be finished even and smooth without using extra cement, complete all as specified and directed.
29All as per Item No 28.00 here-in-before but in cm 1:4 (external surfaces).
30M&L for cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) 75 mm thick as in plinth protection laid in slope 1:12 from outer edge of the wall finished even and fair ,laid in alternate bays including providing 6 mm wide joints through out the thickness of plinth protection in concrete bays and in between walling and plinth protection,joint filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed.
31M&L for 25 mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregeate) as in levelling course to floor finishes, complete all as specified and directed.
32M&L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and directed.
33M&L for 15mm thick rendering on fair faces of brick works in cement mortar 1:4 finished rough for receiving tiles as in dado and skirting, complete all as specified and directed.
34S&F 18-20 mm thick machine cut kota stone slab (area of each slab nexc 0.27 Sqm except space constraint) in flooring laid and jointed with gry cement slurry Mixed with pigment to match the shade of the slab including rubbing and mirror polishing, roughing the surface including dismantling work, complete all as specified and directed.
35All as per Item No 34.00 here-in-before but as in riser to steps, skirting ,dado,window cills fixed with cement mortar 1:4.
36M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and directed.
37M&L for coloured glazed ceramic tiles in vertical surface (thick 600 x 300 x 7mm thick) set and jointed in neat cement slrry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and directed.
38Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc, complete all as specified and directed.
39M&L for PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as in hollow portion of pressed steel frame, complete all as specified and directed.
40M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in bed blocks, bed blocks of hold fasts, coping, PCC cill etc including formwork, complete all as specified and directed.
41S&F factory made MS tubular Box type window of MS rolled steel section conforming to IS-1038 and shall be ISI marked manufactured by ISI approved manufacturer, openable frames shall be fabricated of sections as approved by Engr-in-Charge corner welded to form a solid fused welded joint handles shall be of z section welded with openable frame box steel section(Consisting of both shutter glazed shutter and gauge shutter complete) used in outer frame shutter frame and central frame shall be ERW section of 16 gauge with fixing lugs to be fixed as per provision of IS-1038 except that top lugs shall not be provided , all shutters of windows shall be provided with 4 Nos friction free hinges, 2 Nos 75 mm tower bolts to each leaf of window one at top and one at bottom welded on 3 mm thick steel sheet piece of suitable size which shall be in turn welded to z section f steel window to provide suitable arrangement of using tower bolt and 1 nos bow handle in each shutter. Glazed shutter and , gauged shutter of window , mild steel casement stays 300 mm with hinged joint and two plates with studs complete all as specified with all fittings and fixtures without glazing bars, 3mm sheet glass in glazed shutter and , GI wire mesh,of 0.56 nominal dia and average width of aperature 1.18 mm in gauged shutter, etc, complete all as specified and directed.
42S&F guard bars/grills as specified in between glazed and fly proof window shutter(sand witching guard bars/grill) as per drg No CEPZ/TD-325/07 dt 04.12.07 primer coated, complete all as specified and directed.
43S&F pressed steel frames (size 125 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc, complete all as specified and directed.
44S&F pressed steel frames (size 105 x 60mm ) for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer, complete all as specified and directed.
45S&F plain framed, panelled shutters (any number of panels) with pannel of timber flat on both sides (feather edged) or of veneered particle board with commercial face veneers 35 mm thick 2nd class hard wood supplied and fitted to chowkats, complete all as specified and directed.
46M&L 35 mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc, size of members of shutter as specified in SSR Part-I, Section 8, clause 8.20 (a), fitted to chowkats, complete all as specified and directed.
47S&F Stailess Steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks of galvanised wire staples, complete all as specified and directed.
48S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet, reinforced with MS square tube supplying and fixing in opening as per specification and drawing, complete all as specified and directed.
49M&L for factory made solid panel PVC shutter 30 mm thick ( style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for style and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the styles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification and drawing in SSR part-II and as per sample kept in office of AGE B/R, complete all as specified and directed.
50S&F 300mm ordinary rat tail rod pattern springs including roller plate, complete all as specified and directed.
51S&F Aluminium handles, cast type, anodised 150mm long, complete all as specified and directed.
52S&F aluminium, anodised barrel tower bolts of extruded section and fixed of size 200 mm long, complete all as specified and directed.
53S&F aluminium alloy anodised sliding door bolt with fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed of size 200 mm, complete all as specified and directed.
54S&F anodised aluminum 100mm size butt hinges, extruded aluminum alloy ISI marked, complete all as specified and directed.
55S&F Curtain Rod of stainless steel 25 mm dia fancy type complete and with steel baal, hanging hooks/brackets / end caps of length, complete all as specified and directed.
56M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm, complete all as specified and directed.
57S&F steel water tubing medium grade galvanised with all fittings including short lengths, laid in trenches complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20 mm, complete all as specified and directed.
58S&F in repair 15 mm bore old galvanized pipes including new fittings where necessary fixed complete to wall and ceiling or laid in floors, complete all as specified and directed.
59S&F in repair 20 mm bore old galvanized pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floors, complete all as specified and directed.
60S&F Rotational moulded polythene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 1000 ltrs capacity with and including tank nipple, complete all as specified and directed. Note : The water tank shall be double layer IS Marked duly embossed on face and weight as per IS specifications.
61S&F in repair Ball valves high pressure 20mm dia of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for iron pipe and fixed (Min wt 15 mm -142 grms / 20mm 210 grms), complete all as specified and directed.
62S&F in repair Bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore, complete all as specified and directed.
63S&F in repair Stop valve/Angle valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm dia pipe, ISI marked, complete all as specified and directed.
64S&F in repair stop valve 20 mm dia cast copper alloy, secrewed down high pressure, with crutch or butterfly handle secrewed both ends for iron pipe and fixed, complete all as specified and directed.
65S&F in repair 15 mm bore Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed, complete all as specified and directed.
66S&F in repair 15mm bore wall mixer with overhead shower with 115 mm long bend pipe on upper side, connecting legs & wall flanges, complete all as specified and directed.
67S&F in repair viterous China urinal half stall type white including CP spreader holding screws, waster pipe etc, complete all as specified and directed.
68S&F wash basin of size 550x400mm, vitreous china (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed.
69S&F Vitreous china wash down water closet white orissa pattern of size 550x440mm including integral foot rest excluding flushing cistern and flush pipe) including P or S trap, complete all as specified and directed.
70S&F in repair Viterous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern, flush pipe, incl P or S trap, complete all as specified and directed.
71S&F in repair plastic water closet seat cover,white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.
72S&F in repair PVC low level flushing cistern 10 ltrs capacity white with inlet ball value, float valve and handle incl brackets, PVC flush pipe, complete all as specified and directed.
73S&F in repair stop valve (Concealed type) cast copper chromium plated screwed down, high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe, complete all as specified and directed.
74S&F in repair Hand shower ( health faucet ) with 8mm dia 1.2 meter long flexible braided chromium plated tube with wall hook, complete all as specified and directed.
75S&F in repair chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed.
76S&F in repair tubular towel rail 20mm dia, D type, chromium plated 60cm long between flanges, complete all as specified and directed.
77S&F Gratings of 100 mm dia, fixed in repairs, complete all as specified and directed.
78S&F in repair Stainless Steel soap dish with and including rowel plugs and SS screws, complete all as specified and directed.
79S&F in repair six peg set with 4 mm thick base plate stain less steel fixed with and including rowel plugs and stainless steel screws, complete all as specified and directed.
80S&F in repair glass corner shelf with chromium plated guard rails fiexed with and including stain less steel screws and rowel plugs, complete all as specified and directed.
81S&F in repair sheet glass bevelled edge mirror of selected quality glass of 5 mm sheet glass mounted to walls with fasteners or plugs of selected quality including removal of existing broken/US glass mirror any size, complete all as specified and directed.
82S&F in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.
83M&L in repair for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.
84S&F in repair PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to or laid in trenches or in floors,walls with steel clamps, complete all as specified and directed.
85S&F in repair PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to or laid in trenches or in floors and walls with steel clamps, complete all as specified and directed.
86S&F in repair 110 mm bore PVC (SWR) bend any radius, complete all as specified and directed.
87S&F in repair 110 mm bore PVC (SWR) reducer, complete all as specified and directed.
88S&F in repair 75 mm bore PVC (SWR) vent cowl, complete all as specified and directed.
89S&F in repair 32mm waste fittings, brass, chromium plated for glazed ware basins, etc with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.
90M&L for preparation of newly plastered surface and applying two coats of oil bound distemper with 2mm thick wall care putty, complete all as specified and directed.Note:- Painting shall be done by Painting roller.
91Complete reomoval of existing treatment from walls, by using mechanical equipment (Electric sander ) and preparation of surface to receive the treatment and applying two coats of distemper oil emulsion, complete all as specified and directed. Note:- Once the surface is cleared off old treatment completely, the stage for treatment shall be approved by Eng-in-Charge.
92M&L for preparation of new wall surfaces and applying two coats of cement base paint on wall with approved colour (multi colour pattern as approved by GE), complete all as specified and directed. Note:- Painting shall be done by Painting roller.
93M&L for preparation of old wall plastered or unplastered surfaces and applying one coat of cement base paint on wall with approved colour (multi colour pattern as approved by GE), complete all as specified and directed.Note:- Painting shall be done by Painting roller.
94M&L for two coats of synthetic enamel paint on new steel surfaces including preparation over a coat of red oxide Zinc chrome primer, complete all as specified and directed.
95M&L for one coat of synthetic enamel paints on old steel surfaces including preparation of surfaces, complete all as specified and directed.
96M&L for two coats of synthetic enamel paint on new wooden surfaces including preparation over a coat of pink primmer, complete all as specified and directed.
97M&L for one coat of synthetic enamel paints over old wooden surfaces including preparation of surfaces, complete all as specified and directed.
98M&L for one coat of Black paint for writing letters on surfaces of any description wood,steel, iron, concrete, brick,stone etc exc 10 cm width or girth, complete all as specified and directed.Note:- Letter writing/Painting shall be done at any height as directed by Engr-in-Charge.
99M&L for re-writing and repainting of letter or figures (Block, Roman, Italic or Indian) n exc 30 cm high with synthetic enamel paint of any colour, complete all as specified and directed. Note:- Letter writing/Painting shall be done at any height as directed by Engr-in-Charge.
100M&L for re-writing and repainting of Stops, Commas, Short lines, Dashes,Hyphens, Brackets by using synthetic enamel paint of any colour, complete all as specified and directed.Note:- Letter writing/Painting shall be done at any height as directed by Engr-in-Charge.
101M&L for cement concrete type C2, 1:3:6 (using 40 mm graded crushed stone aggregate) as in surface channel and drains including formwork, complete all as specified and directed.
102Extra for forming fair finished drain or channels 30cm inner girth in cement concrete using extra cement including forms, mould, mitred/stopped ends etc, complete all as specified and directed.
103Construction of Septic tanks, exc, in ordinary soil, foundation,In PCC 1:2:4, brick work in CM 1:4, RCC,Slab covers including RCC precast manhole cover having 6mm plate embedded all and sludge chambers reinforced cover with angle iron frame Vent shaft around/fibre etc.for 50 users (as per Drg No CEUZ/TD/1585/2021, Sheet 1/4 to 4/4), complete all as specified and directed.
104Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 1.8 M dia X 3.0M deep (as per Drg No CEUZ/TD/1585/2021, Sheet 1/4 to 4/4), complete all as sdpecified and directed.
105Excavation in trenches not exceeding 1.5 mtr wide and not exc 1.5 mtr depth for laying of cables, pipe lines, protection pipes and foundations etc and getting out in soft/loose soil, complete all as specified and directed.
106M&L for PCC.1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation mass concrete, complete all as specified and directed.
107M&L for PCC 1:4:8 type D-2 as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for SGSW pipe 150mm dia, complete all as specified and directed.
108M&L for PCC 1:2:4 type B1 as in surface channels, benchings, etc. of manholes finished fair and even, complete all as specified and directed.
109M&L for brick Work old size with Sub Class B bricks, straight or curved on plan n.exc 6m radious on plan built in CM 1:4, complete all as specified and directed.
110Supply only integral Water Proofing Compound conforming to IS, complete all as specified and directed.
111M&L for Salt glazed Stoneware pipe 150mm dia in any length wit or without ear laid in trenches and jointed in CM 1:1, complete all as specified and directed.
112Returning filling in soil including spreading leveling watering and well rammimg in layer n exc 25 cm, complete all as specified and directed.
113Removing excavated soil not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point, complete all as specified and directed.
114Dismantling of stone slabs and tiles of any description or thickness in floors, Aprons laid dry or laid dry and pointed, complete all as specified and directed.Note:- Dismantled tiles shall be refixed only after the sand cushioning is provided , wherever there is undulations then refixing shall be done in patches.
115M&L for 25 mm thick sand filling under floors or in foundtion including watering and consolidation for laying inter locking tiles, complete all as specified and directed.
116M&L for machine pressed precast concrete interlocking paver block of any shape and size approved by EIC, ISI marked (IS:15658-2006) 80mm thick, M-40 grade, in paths and hardstanding,with colored cement laid tightly over and joints filled with dry sand, complete all as specified and directed.Note:- No extra cost shall be claimed by contractor and sand cushioning measured in respective item of 25 mm sand cushioning.
117Demolition of cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.
118Demolition of Brick/stone work built in cement mortar of any descrption incl all necessary quions arches piilars etc, complete all as specified and directed.
119Dismantling mild steel work of any description not otherwise provided for, complete all as specified and directed.
120Dismantling timber scantling 40 sq cm and over in section, in any position, complete all as specified and directed.
121Taking down shutter of any desc n exc 1.5 sqm and refixing in the same opening, complete all as specified and directed.
122Hacking out old broken glasses (Any thickness, size quality, description) from wooden or steel frames fixed with putty or wooden beads, complete all as specified and directed.
123S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 11 to 15 mm neck dia for jointing purlines,rafters etc, complete all as specified and directed.
124S&F Mild steel bolts.exc. 22.5 cm length not exc. 30 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 11 to 15 mm neck dia for jointing truss with chequered plate etc, complete all as specified and directed.
125M&L for PCC 1:2:4 type B-1 (using 12.5 mm graded stone aggregate) for holding nut, bolt of chequered plate , truss and like, complete all as specified and directed.
126S&F 3mm Sheet glass ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane, complete all as specified and directed.
127M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surface of ceiling/facia/chajja, finished surface even and smooth without using extra cement, complete all as specifed and directed. Note:- No extra cost cost shall be claimed by contractor in respect of formwork/scafolding and at any height and site where plaster is to be executed.
128M&L 10 mm thick rendering in cement mortar (1:6) on new fair faces of brick/ concrete surfaces of walls, finished even & smooth without using extra cement, complete all as specified and directed.
129M&L for preparation of newly plastered surfaces of any position /wall and applying two coats of exterior weather proof paint of approved colour (multi colour pattern as approved by GE) over a coat of alkali resistant primer, complete all as specified and directed.
130M&L for preparation of plastered wall / facia /chajja surface and applying two coats of exterior weather proof paint over a coat of alkali reistant primer, complete all as specified and directed.
131M&L for applying three coats of white washing on walls including preparation of newly plastered surfaces, complete all as specified and directed.
132M&L for 75mm thick Cement concrete type D- 2, 1:4:8 (using 40mm graded stone aggregate) as in sub base of floors, pavings complete all as specified and directed.
133M&L for chequered cement concrete tiles of size 30cm x 30cm x 25mm thick set and jointed and pointed in neat cement slurry as in treads and cut polished with gray cement and no pigment, complete all as specified and directed.
134M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.
135Schedule 'A' Part-II (E/M Works)Taking down unserviceable aluminum point wiring (light, fan, socket or power) complete, including all fitting and fixtures such as switches, ceiling roses, pendants, regulators sockets, light fittings etc.) removing material for taking credit (credit for above items should be made as per conditions separately) and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications complete all as specified and directed.
136M&L for Point wiring for one light point/fan point controlled by one way switch with 1.5 sqmm (nominal area) single core FRLS, PVC insulated 1100volts, grade multi stranded unsheathed copper conductor unsheathed in and including non metalic rigid PVC Casing & Caping of 25mm width (medium grade double locking system) complete with all accessories including modular metal flush box, modular white cover plate with frame, blanking plate etc suitable for Mylinc/ Coral/ Sleek model accessories etc and 1.5sqmm (nominal area) single core FRLS, PVC insulated 1100volts grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including cutting, chasing and making good to the disturbed surfaces to match with the existing specification complete all as specified. Note: Three run of copper conductor of required size and one run of casing capping measured as one unit and also colour coding of wiring to be followed as Red/ Yellow/ Blue for phase, black for neutral and green for earth.
137One light/ fan point controlled by one switch one way.
138One socket outlet 6 Amp, 2/3 pin point controlled by one switch one way on same switch board.
139One socket outlet 6 Amps 2/3 pin, point controlled by one switch one way on independent switch board.
140All as per item No 136.00 here-in-before, but point wiring 2.5 sqmm for switch socket combination for 15Amps point controlled by one switch.
141S&F modular switch piano, 1 module, single pole one way 6Amp, complete all as specified and directed.
142S&F modular switch piano, 1 module, single pole one way 16Amp, complete all as specified and directed.
143S&F modular socket 16A, 2/3 pin, 2 module, ISI marked, 230 Volts, complete all as specified and directed.
144S&F modular socket outlet 6A, 3 pin, 2 module, ISI marked, 230 Volts, complete all as specified and directed.
145S&F modular switch bell push 6A, 1 module, 6A, ISI marked, 230 volts, complete all as specified and directed.
146S&F switch piano flush type, 1 module, single pole one way 5Amp, complete all as specified and directed.
147S&F switch piano flush type, 1 module, single pole one way 15Amp, complete all as specified and directed.
148S&F socket outlet 5A, 2 in 1, 5 pin, ISI marked, 230 Volts, complete all as specified and directed.
149S&F socket outlet 15A, 2 in 1, 5 pin, ISI marked, 230 Volts, complete all as specified and directed.
150S&F ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body, complete all as specified and directed.
151S&F modular fan regulator 120watt, step type 2 module, complete all as specified and directed.
152S&F in replacement for LED Tube light fitting, complete with 1x 20 watts, 220V, AC decorative box type with driver, holder in and including LED tube light connection complete prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height, complete all as specified and directed.
153S&F Lamp holder insulated body PVC/ Polycabonate type with back plate suitable for batten/ angular/ pendent holder fittings, complete all as specified and directed.
154S&F LED lamp 7/9/10 watt suitable for lamp holder, complete all as specified and directed.
155S&F in replacement for environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head, 10 watts, 6000K inbuilt LED luminaire comprising of high brightness LEDs, IP-54 protection including connecting electrically using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75sqmm, complete all as specified and directed.
156S&F in replacement for LED Tube light fitting, 1x 10 watts, complete with 2 feet decorative ultra slim near LED lighting fixture with co extruded polycarbonate body, environmental friendly energy efficient ready to use complete prewire and connecting electrically using cord flexible 3 core PVC insulated overall sheathed with flexible copper conductor of size 0.75sqmm, complete all as specified and directed.
157M&L for metallic exhaust fan, 4 blade, heavy duty, double ball bearing, 230V, 50Hz, 250mm sweep having power input 70W speed 1200RPM, with protective bird guard including connecting with three core, 0.75 sqmm PVC insulated copper conductor cable, complete all as sepecified and directed.
158S&F in replacement building security light 35 Watt 230 V with pressure die-cast housing with individual LEDs as light source and lens embedded PC cover having TOP opening separate driver compartment with IP-66 protection and impact resistance of IK-07 complete with connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 1.0sqmm, complete all as specified and directed.
159M&L for street light bracket made up of 40mm bore light grade GI pipe 1.2mtr long including necessary bending welding etc, complete all as specified and directed.
160Supply, laying, connecting and testing of service cable of size 10sqmm 2 core 1100volts grade heavy duty cable, PVC insulated stranded aluminium conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire or drawn in and including medium grade non metalic rigid PVC conduit as per site requirement, flat or circular after taking down old unserviceable cable including other accessories, complete all as specified and directed.
161M&L in replacement sheet metal enclosure MCB DB, SPN 240 volts 8 way with IP-66 IK-09 protection double door 200A complete with appropirate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specificaiton, complete all as specified and directed.Note: MCBs will be measured separately.
162M&L in replacement sheet metal enclosure MCB DB, SPN 240 volts 12 way with IP-66 IK-09 protection double door 200A complete with appropirate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specificaiton, complete all as specified and directed.Note: MCBs will be measured separately.
163S&F MCB SP 240 volt any rating from 6 to 40Amps with rupting capactity 10KA, including providing thimble for out going cable, complete all as specified and directed.
164S&F MCB SPN 240 volt any rating from 6 to 40Amps with rupting capactity 10KA, including providing thimble for out going cable, complete all as specified and directed.
165Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16sqmm 4 core, complete all as specified and directed.
166M&L for sand cushioning to underground cable, provided with a layer 8cm before and 15cm after layig and stretching jointing and testing the cable, complete all as specified and directed.Note: Punned thickess shall be measured for payment purpose.
167Supply and laying brick covering with width equal to length of brick as mechanical protection to cable using sub class 'B' bricks laid flat, size 230mm x 115mm x 75mm, complete all as specified and directed.
168Supply and laying GI pipe 40mm bore light grade in any length with all GI fittings such as socket, elbow, bend, union, Tee etc laid in trenches/duct/culvert/road crossing etc for protection of cables including removing old unserviceable item, complete all as specified and directed.
169M&L for earthing complete with galvanised steel earth plate electrode 60cm x 6cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground leel) with top edge of the plate not less than 1.5 meters below normal ground level, earth plate surrounding by and packed with 15cm thick layer of char coal dust and common salt, earth lead GI wire 4.00mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and thimbled and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm bore and water pipe 20mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-1 & RCC cover all as specified & shown in elect plate No 3 of SSR Part-I of 2009 including testing on completion including taking down existing unserviceable earthing, complete all as specified and directed.Note: Earth wire and protection pipe upto board is included in the rate quoted. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58573147
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 44.38 Lakhs
LAST DATE 08-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Special Repair To Bldg No T-38 At Jhanger Base And Bldg No T-13 & 14 (Or Living) At Rumlidhara Under Age B/R Dett-A Of Ge 862 Ews
Basic Detail
Tender No GER-87/2026-27
Bidding Type Tender
Location
City Rajouri
State Jammu and Kashmir
Key Dates
Publish Date 17 Nov 2026
Submission Date 08 Dec 2026
Open Date 11 Dec 2026
Finance
Tender Value 44.38 Lakhs
Tender Fee 500
EMD 88800
Exemption Available
Document List
BOQ_896623.xls
cfad5e0c-ceb8-4c93-a899-1b1cbd7c3408.html
TD.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 17, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 08, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 16 days
Dec 11, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 19 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_896623.xls

html

cfad5e0c-ceb8-4c93-a899-1b1cbd7c3408.html

pdf

TD.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender