Agriculture Government Departments Closing in 11 days TDR #58569352

Tender For Additional Development Work Along With Extension Of Existing Drainage System Of The Haringhata Meat Plant, Mohanpur, Nadia, Pin-741246 Under West Bengal Livestock Development Corporation Limited, Lb-2, Sector-Iii, Salt Lake City, Kolkata -

Issued by Government Departments · Nadia, West Bengal
Tender Value
49.91 Lakhs
Estimated cost
Bid Submission
02 Dec 2026
11 days left
EMD
99835
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Nadia → West Bengal
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Additional Development Work Along With Extension Of Existing Drainage System Of The Haringhata Meat Plant, Mohanpur, Nadia, Pin-741246 Under West Bengal Livestock Development Corporation Limited, Lb-2, Sector-Iii, Salt Lake City, Kolkata - 700106.

BOQ

Name of Work:- Additional Development Work along with extension of existing drainage system of the Haringhata Meat Plant, Mohanpur, Nadia, PIN-741246 under West Bengal Livestock Development Corporation Limited, LB-2, Sector-III, Salt Lake City, Kolkata - 700106.
Sl. No. Item Description
1Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm
2Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation.
3Earth work in filling in compound, tank, low land,ditches etc. with good earth, in layers not exceeding 150 mm. including breaking clods and consolidating the same by ramming and dressing complete. (Payment will be made on profile measurement before and after the work) (C) (iv) With carried earth arranged by the contractor within a radius exceeding 5 km. but not exceeding 10 km. including cost of carried earth
4(A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)
5Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches
6Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. a) Pakur Variety
7Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes (i) Pakur Variety
8Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 guage black annealed wire at every intersection, complete as per drawing and direction. (i) Tor steel / Mild Steel II. Other than TATA/ SAIL/RINL
9Hire & Labour charge for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works.
10Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (b) 20 mm thick plaster
11Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m.
12DismantlingR.C. floor,roof,beamsetc. including cutting rods and removing rubbish as directed withinaleadof75m. includingstackingof steel bars. (a) In ground floor including roof.
13Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth
14Brick work with 1st class bricks in cement mortar (1:6) (b) In Super structure, ground floor
15125mm. thickbrickworkwith1st class bricks incementmortar (1:4) in ground floor.
16Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (c) 15 mm thick plaster
17Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). a) With 0.5 mm thick sheet
18Galvanised iron sheet eaves gutter fitted and fixed with necessary 50 mm X 6 mm M.S flat bar clamps bent to design, bolts, nuts, washers etc. complete. (b) 300 mm. wide gutter
19Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping) (A) 300 mm lapping each way (a) With 0.60 mm sheet
20Supplying, fitting and fixing glass reinforced polyester translucent fiber glass sheet to match with GCI Corrugation as per IS:12866-1989 in roof fitted and fixed with 10 mm dia \\"J\\" or \\"L\\" hook, bolts and nuts, limpet and bitumen washers and putty with150mm endlap and one corrugation minimum side lap complete. b) 2.0mm +/- 0.2 mm thick sheet.(3.25Kg/Sq.m) i) Natural white or tinted blue colour
21(a) Supplying, fitting and fixing steel rolling shutter profile type with 18 B.G . of approved type steel latche section 75mm wide, fitted with coil wire spring to necessiate the fitting of required Nos. of C.I. Pulleys on heavy type solid drawn seamless steel tube complete with locking arrangements both inside and outside specially builtup side guide channels including providing a hood for the steel rolling shutter in the room, painting two coats of approved aluminium paint over a coat of red lead primer complete. 1. (Measurement will be made on the area of opening covered by the rolling shutter corrected upto 2 decimal.) 2. Payment of painting to be separately.
22Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (b) Two Coats i) Water based interior grade Acrylic Primer
23Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Standard Quality
24(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.
25(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary b) On steel or other metal surface : With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white)
26Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge. 10-12 Micron thickness Annodizing film Natural white
27Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987 iii) 5mm thick clear glass.
28Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987;(A) clear, toughened glass conforming to IS: 2553-1992 (part-II) (A) clear, toughened glass conforming to IS: 2553-1992 (part-II) (i) 6mm thick
29Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge. (Payment will be made on finished length of the work). (A) In 10-12 Micron thickness Annodizing film, I) Natural white g) Fixed glazing. i) Top, bottom and side member.
30ii) Mullion.
31iii) Glazing clip
32Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed. (i) 16 mm dia bolt (b) 450 mm long
33(ii) 20 mm dia bolt (c) 600 mm long
34Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. (iii) 35 mm. thick
35TAXES & DUTIES
36Add: G.S.T. @ 18% of Rs. 41,88,397=54 (Sl. No. 1.01 to 1.34) i.e. Rs. 7,53,911=56
37Add : Labour Cess @ 1% of Rs. 49,42,309=10 i.e. Rs. 49,423=09 Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58569352
AUTHORITY Government Departments
TENDER VALUE 49.91 Lakhs
LAST DATE 02-12-2026
Authority
Authority Name Animal Resources Development Department
Work Description Tender for Additional Development Work Along With Extension Of Existing Drainage System Of The Haringhata Meat Plant, Mohanpur, Nadia, Pin-741246 Under West Bengal Livestock Development Corporation Limited, Lb-2, Sector-Iii, Salt Lake City, Kolkata - 700106.
Basic Detail
Tender No WBARD/WBLDC/NIT-1097e/2026-27 Dated 03/11/2026
Bidding Type Tender
Location
City Nadia
State West Bengal
Key Dates
Publish Date 17 Nov 2026
Submission Date 02 Dec 2026
Open Date 04 Dec 2026
Finance
Tender Value 49.91 Lakhs
Tender Fee Ref. Documents
EMD 99835
Exemption Available
Document List
a1c7ebcd-a29a-453f-8ef8-49d4a4a403fa.html
BOQ_5212764.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 17, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 02, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 11 days
Dec 04, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 13 days

Tender Documents

Download All (ZIP) ↓
html

a1c7ebcd-a29a-453f-8ef8-49d4a4a403fa.html

xls

BOQ_5212764.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender