Tender For Electrification Package For Blocks 145,122,101,113,119B, 111,107C 135A Etc For Inrp Site, Tarapur
Tender Value
23.37 Crore
Estimated cost
Bid Submission
14 Dec 2026
26 days left
EMD
33.37 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Palghar → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Electrification Package For Blocks 145,122,101,113,119B, 111,107C 135A Etc For Inrp Site, Tarapur
BOQ
| Sl. No. | Item Description |
| 1 | Supply, Installation, Testing and Commissioning of following configuration 415V, 3-phase, 4 wire, double door, with R Y B Phase LED indication and MCB position indication through glass front, IP-54, Prewired with HFFR copper wires, horizontal type, metallic Double Door, Phase Segregated three pole and neutral MCB Distribution Board fabricated out of 2 mm thick ,powder coated with RAL7035 shade, pre-galvanised G.I. sheet steel, suitable for flush/Surface mount in brick wall complete with appropriate rating earth and neutral bar, din bar, brass earthing studs, phase distribution drawing, danger board, name plate, 2 mm thick removable gland plate on both top and bottom side with required number of knock out holes, neoprene gasket, etc. as per tender technical specifications. |
| 2 | 4 way having 1 no. main incomer of In = 16 A TPN MCB, Ics=10kA, Type C with 1 no. In = 16 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 12 nos. outgoing of In =6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 3 | 4 way having 1 no. main incomer of In = 25 A TPN MCB, Ics=10kA, Type C with 1 no. In = 25 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 12 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 4 | 4 way having 1 no. main incomer of In = 32 A TPN MCB, Ics=10kA, Type C with 1 no. In = 32 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 12 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 5 | 6 way having 1 no. main incomer of In = 25 A TPN MCB, Ics=10kA, Type C with 1 no. In = 25 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 18 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 6 | 6 way having 1 no. main incomer of In = 32 A TPN MCB, Ics=10kA, Type C with 1 no. In = 32 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 18 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 7 | 6 way having 1 no. main incomer of In = 40 A TPN MCB, Ics=10kA, Type C with 1 no. In = 40 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 18 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 8 | 6 way having 1 no. main incomer of In = 16 A TPN MCB, Ics=10kA, Type C with 1 no. In = 16 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 18 nos. outgoing of In =6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 9 | 8 way having 1 no. main incomer of In = 25 A TPN MCB, Ics=10kA, Type C with 1 no. In = 25 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 24 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 10 | 8 way having 1 no. main incomer of In = 40 A TPN MCB, Ics=10kA, Type C with 1 no. In = 40 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 24 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 11 | 8 way, TPN MCB DB with Incomer of 16A, Isc=10kA, Type C, (100mA) 16A DP RCBO for each phase and 24 Nos of 6A, Isc=10kA, Type C, SPN Ougoing MCB feeder as per SLD and technical specification |
| 12 | 8 way having 1 no. main incomer of 32A TPN MCB, Isc=10kA, Type C with 1 no. of 32A, Isc=10kA, DP, MCB and RCCB(100mA) as incomer for each phase and 24nos. outgoing of 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA breaking capacity and as per tender technical specifications. |
| 13 | 8 way having 1 no. main incomer of 63A TPN MCB, Isc=10kA, Type C with 1 no. of 63A, Isc=10kA, DP, MCB and RCCB(100mA) as incomer for each phase and 24nos. outgoing of 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA breaking capacity and as per tender technical specifications. |
| 14 | 12 way having 1 no. main incomer of In = 40 A TPN MCB, Ics=10kA, Type C with 1 no. In = 40 A, Ics=10kA, DP, RCBO(100mA) as incomer for each phase and 24 nos. outgoing of In =16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 15 | 10way having 1 no. main incomer of 63A TPN MCB, Isc=10kA, Type C with 1 nos. of 63A, Isc=10kA, DP, MCB and RCCB (100mA) as incomer for each phase and 30 nos. outgoing of 16A SPN MCB suitable for 240V rating, Type \\"C\\" curve, 10 kA breaking capacity and as per tender technical specifications. |
| 16 | 10way having 1 no. main incomer of 32A TPN MCB, Isc=10kA, Type C with 1 nos. of 32A, Isc=10kA, DP, MCB and RCCB(100mA) as incomer for each phase and 30 nos. outgoing of 16A SPN MCB suitable for 240V rating, Type \\"C\\" curve, 10 kA breaking capacity and as per tender technical specifications. |
| 17 | 10 way having 1 no. main incomer of 25A TPN MCB, Isc=10kA, Type C with 1 no. of 25A, Isc=10kA, DP, MCB and RCCB (100mA) as incomer for each phase and 30 nos. outgoing of 16A SPN MCB suitable for 240V rating, Type \\"C\\" curve, 10 kA breaking capacity . |
| 18 | 12way having 1 no. main incomer of 32A TPN MCB, Isc=10kA, Type C with 1 nos. of 32A, Isc=10kA, DP, MCB and RCCB (100mA) as incomer for each phase and 36nos. outgoing of 16A SPN MCB suitable for 240V rating, Type \\"C\\" curve, 10 kA breaking capacity and as per tender technical specifications. |
| 19 | 12way having 1 no. main incomer of 25A TPN MCB, Isc=10kA, Type C with 1 nos. of 32A, Isc=10kA, DP, MCB and RCCB (100mA) as incomer for each phase and 36nos. outgoing of 16A SPN MCB suitable for 240V rating, Type \\"C\\" curve, 10 kA breaking capacity and as per tender technical specifications. |
| 20 | Supply, Installation, Testing and Commissioning of following configuration 240V, 1-phase, 2 wire, with Phase and MCB position indication through glass front, Pre-wired with HFFR copper wires, IP-54, MCB Distribution Board fabricated out of 2mm thick Pre Galvanised G. I sheet steel, powder coated with RAL7035 shade, suitable for flush/Surface mount in brick wall complete with appropriate rating earth and neutral bar, din bar, brass earthing studs, phase distribution drawing, danger board, name plate, earth bar, din bar for MCB mounting, 2 mm thick removable gland plate on both top and bottom side with required number of knock out holes, neoprene gasket, check-nuts etc. as required as per tender technical specifications. |
| 21 | 12 way having 1 no. main incomer of In = 63A DP MCB, Ics=10kA, Type C and 12 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 22 | 12 way having 1 no. main incomer of In = 40A DP MCB, Ics=10kA, Type C and 12 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 23 | 12 way having 1 no. main incomer of In = 16A DP MCB, Ics=10kA, Type C and 12 nos. outgoing of In = 6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 24 | 10 way having 1 no. main incomer of In = 25A DP MCB, Ics=10kA, Type C and 10 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 25 | 10 way having 1 no. main incomer of In = 16A DP MCB, Ics=10kA, Type C and 10 nos. outgoing of In = 6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 26 | 8 way having 1 no. main incomer of In = 63A DP MCB, Ics=10kA, Type C and 8 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 27 | 8 way having 1 no. main incomer of In = 40A DP MCB, Ics=10kA, Type C and 8 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 28 | 8 way having 1 no. main incomer of In = 32A DP MCB (100mA), Ics=10kA, Type C and 8 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 29 | 8 way having 1 no. main incomer of In = 25A DP MCB, Ics=10kA, Type C and 8 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 30 | 8 way having 1 no. main incomer of In = 16A DP MCB, Ics=10kA, Type C and 10 nos. outgoing of In = 6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 31 | 6 way having 1 no. main incomer of In = 40 A DP MCB, Ics=10kA, Type C and 6 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 32 | 6 way having 1 no. main incomer of In = 32A DP MCB (100mA), Ics=10kA, Type C and 6 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 33 | 6 way having 1 no. main incomer of In = 25A DP MCB, Ics=10kA, Type C and 6 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 34 | 6 way having 1 no. main incomer of In = 25A DP MCB (100mA), Ics=10kA, Type C and 6 nos. outgoing of In = 6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 35 | 6 way having 1 no. main incomer of In = 16 A DP MCB, Ics=10kA, Type C and 6 nos. outgoing of In = 10 A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 36 | 6 way having 1 no. main incomer of In = 16 A DP MCB, Ics=10kA, Type C and 6 nos. outgoing of In = 6 A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 37 | 4 way having 1 no. main incomer of In = 32 A DP MCB (100mA), Ics=10kA, Type C and 4 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 38 | 4 way having 1 no. main incomer of In = 25A DP MCB, Ics=10kA, Type C and 4 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 39 | 4 way having 1 no. main incomer of In = 16A DP MCB, Ics=10kA, Type C and 4 nos. outgoing of In = 10A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 40 | 4 way having 1 no. main incomer of In = 25 A DP MCB (100mA), Ics=10kA, Type C and 4 nos. outgoing of In = 6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 41 | 4 way having 1 no. main incomer of In = 16A DP MCB, Ics=10kA, Type C and 4 nos. outgoing of In = 6A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 42 | 4 way having 1 no. main incomer of In = 40 A DP MCB, Ics=10kA, Type C and 4 nos. outgoing of In = 16A SPN MCB. suitable for 240V rating, Type \\"C\\" curve, 10 kA rated service breaking capacity and as per tender technical specifications. |
| 43 | DC DB |
| 44 | 4 way having 1 no. main incomer of In = 16 A DP DC MCB, and 4 nos. outgoing of In = 6A DP DC MCB suitable for 110V DC and as per tender technical specifications. |
| 45 | 4 way having 1 no. main incomer of In = 25 A DP DC MCB, and 4 nos. outgoing of In = 10A DP DC MCB suitable for 110V DC and as per tender technical specifications. |
| 46 | 8 way having 1 no. main incomer of In = 10 A DP DC MCB, and 8 nos. outgoing of In = 6A DP DC MCB as per tender technical specifications. |
| 47 | Supply, installation, testing and commissioning of 40 W Surface Mounted LED Batten Luminaire, 1200 mm long, extruded aluminium housing with opal polycarbonate diffuser, integrated constant-current LED driver, minimum efficacy 110 lm/W, luminous flux not less than 4400 lumens, CRI ≥80, PF ≥0.95, THD ≤10%, surge protection minimum 2.5 kV, operating on 220–240 V AC, complete with mounting accessories. |
| 48 | SITC of LED surface mount downlighter light complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, Surface mounted with a nominal system lumen output of equal or more than 2400lumens and a minimum system efficacyof 100lm/W.The luminaire shall have a rated system lifetime of 25,000 burning hours. The luminaire should have a CCT of 5700K,Initial chromaticity <5 and CRI > 80.The luminaire shall meet IP20 rating with THD < 10% and PF > 0.9 and in-built surge protection of 4kV. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof siliconerubber ring. The total power consumption should not exceed 24W (including driver). |
| 49 | Supply of LED light fittings complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, suitable PVC terminal box, LED Highbay with a nominal system lumen output of 18000 lumens and a minimum system efficacy of not less than 140 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70B50. The luminaire should have a CCT of 5700K and CRI > 70 and SDCM<5. The luminaire shall meet IP66 and IK 08 rating with THD < 10% and PF > 0.95 and in-built surge protection of 4kV. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof silicone rubber ring. The total power consumption should not exceed 130W (including BIS Compliant integrated driver) and other requirements shall be as per tender technical specifications. |
| 50 | SITC of LED Surface mount Periphery light complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, Surface mounted with a nominal system lumen output of 4200 lumens and a minimum system efficacyof 120lm/W.The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a CCT of 5700K, and CRI > 70.The luminaire shall meet IP66 rating with THD < 10% and PF > 0.95 and in-built surge protection of 4kV. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof silicone rubber ring. The total power consumption should not exceed 36W (including driver). |
| 51 | Supply, installation, testing and commissioning of 36 W LED Flameproof Tube Light, suitable for hazardous locations, Ex db eb IIC T6 Gb, Zone 1 & Zone 2, IP66, die-cast aluminium housing with toughened glass diffuser, stainless steel fasteners, integral constant-current LED driver, minimum efficacy 110 lm/W, complete with Ex-certified cable gland, mounting accessories and all hardware. |
| 52 | SITC of LED 4ft Slim LED Tube light fixture with 2 no. of LED Tube having a nominal system lumen output of minimum 2340 lumens and a minimum system efficacy of 130 lm/W per tube. The luminaire should have a CCT of 6500K and CRI>80. The luminaire shall meet IP20 rating with THD<10%, PF>0.95, SDCM< 7 and RoHS compliant. The luminaire housing should made of Extruded Aluminium with extruded PC diffuser & should have anodised finish. The total power consumption should not exceed 36W (including driver). |
| 53 | SITC of LED recess mount 2'x2' grid light complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, Recess/Surface mounted with a nominal system lumen output of 4200lumens and a minimum system efficacyof 120lm/W.The luminaire shall have a rated system lifetime of 50,000 burning hours at L70B50 @ 50k hrs. The luminaire should have a CCT of 5700K,Initial chromaticity <5 and CRI > 80.The luminaire shall meet IP20 rating with THD < 10% and PF > 0.9 and in-built surge protection of 4kV. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof siliconerubber ring. The total power consumption should not exceed 36W (including driver). |
| 54 | SITC of 230V light fitting, LED Bulkhead type with a nominal system lumen output of 780 lumens and a minimum system efficacy of 120 lm/W. The luminaire should have a CCT of 5700K and CRI > 80. The luminaire shall meet IP65 rating with THD < 10% and PF > 0.95 , L70B50 shall be 50000 hours, complete with light fitting SS accessories, flexible GI metallic conduit sleeves, Cu lugs, 3 inch pvc terminal box, . . The luminaire housing should have made of High pressure die cast Aluminium with high quality PMMA diffuser. The total power consumption should not exceed 6.5 W (including BIS Compliant integrated driver) and other requirements shall be as per tender technical specifications. |
| 55 | SITC of light fitting, LED Bulkhead type with a nominal system lumen output of 1440 lumens and a minimum system efficacy of 120 lm/W. The luminaire should have a CCT of 5700K and CRI > 80. The luminaire shall meet IP65 rating with THD < 10% and PF > 0.95 , L70B50 shall be 50000 hours, complete with light fitting SS accessories, flexible GI metallic conduit sleeves, Cu lugs, 3 inch pvc terminal box, . The luminaire housing should have made of High pressure die cast Aluminium with high quality PMMA diffuser and suitable for 110V DC operation. The total power consumption should not exceed 12 W (including BIS Compliant integrated driver) and other requirements shall be as per tender technical specifications. |
| 56 | SITC of light fitting, LED Bulkhead type with a nominal system lumen output of 1200 lumens and a minimum system efficacy of 120 lm/W. The luminaire should have a CCT of 5700K and CRI > 80. The luminaire shall meet IP65 rating with THD < 10% and PF > 0.95 , L70B50 shall be 50000 hours, complete with light fitting SS accessories, flexible GI metallic conduit sleeves, Cu lugs, 3 inch pvc terminal box, . . The luminaire housing should have made of High pressure die cast Aluminium with high quality PMMA diffuser. The total power consumption should not exceed 10W (including BIS Compliant integrated driver) and other requirements shall be as per tender technical specifications. |
| 57 | SITC of \\"FLAMEPROOF\\" LED Bulkhead type with a nominal system lumen output of 1200 lumens and a minimum system efficacy of 120 lm/W. The luminaire should have a CCT of 5700K and CRI > 80. The luminaire shall meet IP65 rating with THD < 10% and PF > 0.95 , L70B50 shall be 50000 hours, complete with light fitting SS accessories, flexible GI metallic conduit sleeves, Cu lugs, 3 inch pvc terminal box, . . The luminaire housing should have made of High pressure die cast Aluminium with high quality PMMA diffuser. The total power consumption should not exceed 10W (including BIS Compliant integrated driver) and other requirements shall be as per tender technical specifications |
| 58 | Supply, installation, testing and commissioning of 2 × 8 W LED Flame Proof Luminaire, suitable for Zone 1 & Zone 2 hazardous areas, die-cast aluminium housing with toughened glass diffuser, IP65/IP66 protection, , complete with LED driver, Ex-certified cable gland, mounting accessories and all necessary hardware. |
| 59 | SITC of LED light fittings complete with light fitting accessories, including supply of fixing SS accessories,flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs,LED decorative type sleek mirrorWall light with high diffuser of 14W with nominal system output of 1400 lumens and should have a CCT of 3000K and CRI>80.The Luminaire should made of metal with high quality PMMA diffuser.The total power consumption should not exceed 14W (including driver). |
| 60 | SITC of LED light fittings complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, suitable PVC terminal box, LED Highbay with a nominal system lumen output of 12500 lumens and a minimum system efficacy of not less than 140 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70B50. The luminaire should have a CCT of 6500K and CRI > 80 and SDCM<5. The luminaire shall meet IP66 and IK 08 rating with THD < 10% and PF > 0.95 and in-built surge protection of 4kV. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof silicone rubber ring. The total power consumption should not exceed 90W (including BIS Compliant integrated driver) and other requirements shall be as per tender technical specifications. |
| 61 | SITC of LED surfcae mount 2'x2' grid light complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, Surface mounted with a nominal system lumen output of 4200lumens and a minimum system efficacyof 120lm/W.The luminaire shall have a rated system lifetime of 50,000 burning hours at L70B50 @ 50k hrs. The luminaire should have a CCT of 5700K,Initial chromaticity <5 and CRI > 80.The luminaire shall meet IP20 rating with THD < 10% and PF > 0.9 and in-built surge protection of 4kV. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof siliconerubber ring. The total power consumption should not exceed 36W (including driver). |
| 62 | SITC of LED integral driver Flood light with a nominal system lumen output of 18000 lumens and a minimum system efficacy of 120 lumen/watt. The luminaire should have a CCT of 5700K and a CRI>70. The luminaire shall meet IP66 rating with THD<10% and PF>0.95. The luminaire housing should be made of pressure die cast aluminium and front toughened glass cover. The total power consumption should not exceed 150W (including driver). |
| 63 | SITC of LED integral driver Bollard/ Landscape light with a nominal system lumen output of 600lumens and a minimum system efficacy of 75lumen/watt. The luminaire should have a CCT of 5700K and a CRI>80. The luminaire shall meet IP65 rating with IK07, THD<20% and PF>0.95. The luminaire housing should be made of aluminium/ GI with Black powder coating and polycarbonate diffuser. The total power consumption should not exceed 8W (including BIS compliant driver). Submission of LM80-08 for LED source & LM79-08 for Luminaire from NABL Accredited Lab mandatory. The light fitting shall be supplied with SS accessories, flexible GI metallic conduit sleeves, Cu lugs, 3 inch PVC terminal box and other requirements as per tender technical specifications. |
| 64 | SITC of LED street light fitting of not more than 40W having System Efficacy >120lm/W, system output >=4800 Lumens, THD<10%, Power Factor >=0.95, CRI >70, CCT 6500K, IP66 protected pressure die cast aluminium housing having PC diffuser with IK08.The luminaire shall be supplied with pipe of suitable dia for mounting of the same. Driver shall have 6KV Surge protection. Submission of LM80-08 for LED source & LM79-08 for Luminaire from NABL Accredited Lab mandatory. BIS certified. The light fitting shall be supplied with SS accessories, flexible GI metallic conduit sleeves, Cu lugs, 3 inch PVC terminal box and other requirements as per tender technical specifications. |
| 65 | SITC of LED integral driver 100W flood light Industrial Batten Surface mounted with a nominal system lumen output of 12500 lumens and a minimum system efficacy of 125 lumen/watt. The luminaire should have cool white colour temperature 6500K and a CRI>80. The luminaire shall meet IP66 rating with THD<10% & PF>0.9. The luminaire housing should be made of pressure die cast aluminium. The total power consumption should not exceed 104 W (including driver) |
| 66 | SITC of LED 4ft Slim LED Tube light fixture with one no. of LED Tube having a nominal system lumen output of minimum 2340 lumens and a minimum system efficacy of 130 lm/W. The luminaire should have a CCT of 6500K and CRI>80. The luminaire shall meet IP20 rating with THD<15%, PF>0.9, SDCM< 7 and RoHS compliant. The luminaire housing should made of Extruded Aluminium with extruded PC diffuser & should have anodised finish. The total power consumption should not exceed 18W (including driver). |
| 67 | SITC of Black painted Extruded aluminium housing single sided 8W LED signage exit light,Red LED’s mounted inside the housing,Laser engraved Signage matter on Single / Double Acrylic sheet fixed on one side along with Ni-Cd Battery back up to 2 hrs. (Charged up to 8 - 10 Hrs),Mounting strings provided for pendent mounting ,Operating Voltage 150-280V AC and Ingress protection – IP42 |
| 68 | SITC of LED Highbay with a nominal system lumen output of 19500 lumens and a minimum system efficacy of 130 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a color temperature of 6500K and CRI > 80 and SDCM<5. The luminaire shall meet IP66 and IK 08 rating with THD < 10% and PF > 0.95 and in-built surge protection of 4kV. The luminaire should be tested from NABL accredated LAB and should have proper IES file. The luminaire housing should made of High Pressure die cast Aluminium with narrow beam optics and having gasket of heat proof siliconerubber ring. The total power consumption should not exceed 157W (including driver) |
| 69 | SITC of 150W SON HPSV lighting fixture complete with SON-T 150W high pressure sodium lamp, high efficiency aluminium reflector, die-cast aluminium housing, toughened glass cover, non- integral control gear comprising ballast, ignitor and capacitor, IP65/IP66 protection, suitable for 230V AC 50Hz supply, complete with mounting accessories, testing and commissioning. |
| 70 | SITC of 70W SON HPSV lighting fixture complete with 70W High Pressure Sodium Vapour Lamp, non-integral control gear comprising ballast, ignitor and capacitor, die-cast aluminium housing, high efficiency aluminium reflector, toughened glass cover, IP65/IP66 protection, suitable for 230/240V AC, 50Hz supply, pole arm mounting arrangement, including all accessories, testing and commissioning complete |
| 71 | Type B Low intensity LED based aviation light as per the Civil Aviation requirement (ICAO) as per tender specification. |
| 72 | SITC of LED integral driver Flood light with a nominal system lumen output of 8400 lumens and a minimum system efficacy of 120 lumen/watt. The luminaire should have a CCT of 5700K and a CRI>70. The luminaire shall meet IP66 rating with THD<10% and PF>0.95. The luminaire housing should be made of pressure die cast aluminium and front toughened glass cover. The total power consumption should not exceed 70W (including driver). |
| 73 | SITC of LED light fittings complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, LED medium bay with a nominal system lumen output of 10400 lumens and a minimum system efficacy of not less than 130 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a CCT of 5700K and CRI > 70 and SDCM<5. The luminaire shall meet IP66 and IK 08 rating with THD < 10% and PF > 0.95 and in-built surge protection of 4kV. The luminaire should be tested from NABL accredated LAB and should have proper IES file. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof silicone rubber ring. The total power consumption should not exceed 80W (including driver). |
| 74 | SITC of LED Circular Recessed downlighter with a nominal system lumen output of 1500lm and a minimum system efficacy of 100lm/W. The luminaire should have a CCT of 6500K and CRI> 80. The luminaire shall meet IP20 rating with THD<10%, PF>0.95. The luminaire housing should made of polycarbonate with high effeciency diffuser. The total power consumption should not exceed 14W (including driver). |
| 75 | SITC of LED Recess mount downlight light complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs,Recess mounted with a nominal system lumen output of 2000 lumens and a minimum system efficacyof 110lm/W.The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a CCT of 6500K,and SDCM <5 and CRI > 80.The luminaire shall meet IP65 rating with THD < 10% and PF > 0.95 and in-built surge protection of 4kV. The luminaire housing should made of High Pressure die cast Aluminium with wide beam optics and having gasket of heat proof siliconerubber ring. The total power consumption should not exceed 18W (including driver) |
| 76 | SITC of LED 4ft Slim Batten with a nominal system lumen output of 2100 lumens and a minimum system efficacy of 115 lm/W.The luminaire should have CCT 6500K and CRI > 80. The luminaire shall meet IP20 protection rating with THD < 10% and PF > 0.9. The luminaire housing should made of Extruded Aluminium with extruded PC diffuser & should have anodised finish. The total power consumption should not exceed 19W (including driver) |
| 77 | SITC of 19 Watt LED Batten having system efficacy 115 lm/W, system output 2100 lumens, THD < 10%, Power Factor > 0.9, CRI > 80, CCT 6500, CRCA Powdered coated housing and IP65 protection |
| 78 | Supply, installation, testing and commissioning of 30W LED recessed downlighter complete with high efficiency SMD LED module, integral constant current driver, die-cast aluminium housing, high efficiency reflector and optical diffuser, having minimum system efficacy of 110 lm/W and minimum lumen output of 3300 lumens, CRI ≥80, PF ≥0.90, surge protection minimum 4kV, suitable for 220–240V AC, 50Hz supply, recessed false ceiling mounting arrangement, complete with all accessories, fixing hardware and commissioning. |
| 79 | SITC of LED Recessed 1ft x 4ft Troffer Luminaire with a nomial system lumen output of 3200 lumens and a minimum system efficacy of 90 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a color temperature of 6500K and CRI>80. The luminaire shall meet IP20 rating with THD<10% and PF >0.9. The luminaire housing should made of powder coated metallic CRCA with high efficiency opal diffuser. The total power consumption should not exceed 35W (including driver) |
| 80 | Supply, installation, testing and commissioning of 300mm diameter round surface mounted LED fixture complete with high efficiency SMD LED module and integral constant current driver, having minimum system efficacy of 110 lm/W and minimum lumen output of 1320 lumens, CRI ≥80, PF ≥0.90, wide beam optical diffuser, suitable for 220–240V AC, 50Hz supply, with polycarbonate/aluminium housing, opal diffuser, including mounting accessories, fixing hardware and commissioning complete. |
| 81 | Supply and Installation of Single phase heavy duty exhaust fan of sweep 300 mm with FRP duct suitable for domestic application |
| 82 | Supply |
| 83 | Installation, Testing and Commissioning |
| 84 | Supply, Installation, Testing and Commissioning of new energy efficient High Grade ABS Basic Hand Dryers, wall mounted, 1800Watt or above, Touch free Infra-red Sensor activation, AC220-240V, 50/60Hz and as per tender technical specifications. |
| 85 | Supply and laying of following size earthing conductor at 1000 mm below ground level including excavation, brazing, connection to earth pits, refilling the trench etc. as required. |
| 86 | 95 sq. mm stranded bare tinned copper conductor |
| 87 | Supply and laying of 125 sq mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 88 | Supply and laying of 70 sq. mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 89 | Supply and laying of 35 sq mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 90 | Supply and laying of 25 sq. mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 91 | Supply and laying of 16 sq. mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 92 | Supply and laying of 6 sq. mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 93 | Supply and laying of 4 sq. mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 94 | Supply and laying of 2.5 sq. mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 95 | Supply and laying of 2 x 10 sq. mm Cu PVC insulated earthing conductor in 25mm HDPE pipe including underground laying with excavation/ clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge.(supply of HDPE pipe included in Contractor's scope) |
| 96 | Supply and laying of 10 sq mm stranded bare tinned copper conductor including clamping/ cleating on surface/ floor/ ceiling/ wall/ tray, making chase, repairing the same, connection through brazing/ bolting etc. as per instructions by Engineer-In-Charge. |
| 97 | SITC of 63A rated welding receptacles. |
| 98 | Supply and laying of 14 SWG tinned solid copper conductor throughout along the conduit including fixing with ties, brazing etc as required. |
| 99 | Supply and laying of 25mm x 3mm tinned copper flat |
| 100 | Supply and installation of Busbar Insulator of size M8 x 40mm, MOC: Epoxy as per tender specification. |
| 101 | Supply and installation of Copper lug suitable for 70 Sq.mm stranded tinned copper conductor |
| 102 | Supply and installation of Copper lug suitable for 95 Sq.mm stranded tinned copper conductor |
| 103 | Supply and installation of Copper lug suitable for 10 Sq.mm stranded tinned copper conductor |
| 104 | Supply and installation of Copper lug suitable for 35 Sq.mm stranded tinned copper conductor |
| 105 | Supply and installation of Copper lug suitable for 125 Sq.mm stranded tinned copper conductor |
| 106 | Supply and installation of M10 brass nut bolt, 3/4\\" long suitable for 10mm threaded hole for making connection to earth pad. |
| 107 | Supply and installation GI C Clamp of size 25*3 mm ,length 200mm having suitable size of hole for fixing of cu strip. |
| 108 | Supply and fixing of vertical air termination made up of 20 mm dia., 1 mtr. long copper rod attached to 50 mm dia. Copper sphere having drilled and tapped holes for fixing 5 nos. of 150 mm long spikes and square copper base plate of 150 mm length and 10 mm thickness as per latest IS & technical specification and approved drawing. |
| 109 | Supply and erection of plate earth electrode pit comprising of 600 X 600 X 3.15mm thick tinned copper earth plate, 50mm dia class B watering pipe of 2.7 mtr length, funnel, earth conductor connection, test link, concrete inspection pit with GI cover having lifting arrangement, etc. as perIS:3043-2001. |
| 110 | Supply and erection of rod earth electrode pit comprised of 25mm dia. and 3mtr long tinnedcopper earth rod, connection of 2 x 95 sq mm conductor, 50mm dia class B watering pipe of 3 mtr length, funnel, earth conductor connection clamp, test link, concrete inspection pit with GI coverhaving lifting arrangement, etc. as per IS:3043-2001. |
| 111 | Supply and installation of test link box and termination of earthing conductor from earthing protection system and earth pit and should consist of 2mm thick powder coated pre-galvanised G.I. weather proof sheet enclosure with cover, having 2 parallel paths of 30 mm x 6mm copper strip link, teflon sealing after connection, earthing stud, suitable for connecting of 8 nos. of 95sqmm earthing conductors etc and as per tender technical specifications. |
| 112 | Supply and installation of test link box and termination of earthing conductor from Lightning protection system and earth pit and should consist of 2mm thick powder coated pre-galvanised G.I. weather proof sheet enclosure with cover, having 30 mm x 6mm copper strip link, teflon sealing after connection, earthing stud, suitable for connecting of Cu strip and 2 nos. of 95sqmm earthing conductors etc and as per tender technical specifications |
| 113 | Supply, Installation, Testing and Commissioning of the following Modular switches in the existing recess mounted GI box as per Technical specifications. |
| 114 | Supply of 1 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 115 | Installation, Testing and Commissioning of 1 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 116 | Supply of 2 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 117 | Installation, Testing and Commissioning of 2 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 118 | Supply of 3 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 119 | Installation, Testing and Commissioning of 3 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 120 | Supply of 4 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 121 | Installation, Testing and Commissioning of 4 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 122 | Supply of 5 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 123 | Installation, Testing and Commissioning of 5 nos. of 6A, Single Pole, Modular Switch with heavy duty polycarbonate face plate and suitable mounting arrangements as per technical specification. |
| 124 | Supply & Installation of 2 nos. of 6A/16A (compatible with both 6A and 16A), Single phase Modular type socket with 16A switch for each socket and heavy duty Polycarbonate face plate, 2nos. of plug tops and suitable mounting arrangements as per technical specification. |
| 125 | Supply & Installation of 1 nos. of 6/16A, Single phase Modular socket with 16A switch for socket and heavy duty Polycarbonate face plate, 1no. Of plug top and suitable mounting arrangements as per technical specification. |
| 126 | Supply and Installation of the following modular heavy duty polycarbonate box , Fire Retardant, ISI marked switches, sockets, plug tops, PVC Box and combined face plates as per technical specification. |
| 127 | 4-modular PVC box including cover plate, face plate with 2 nos. of RJ11(4 Pin) connector with shutter telephone socket and 2 nos of RJ45 socket (UTP/STP) with shutter and connector. |
| 128 | 2-modular PVC box including cover plate with face plate with 2 nos of RJ45 socket (UTP/STP) with shutter and connector. |
| 129 | Supply & Installation of 12 Way modular domestic type Switch box with cover plate, 4 nos of switches of rating 6 Amp and 4 no of sockets ( 6/20 Amps ), suitable for surface mounting as per attached technicalspecification |
| 130 | Supply and Installation of 6 Way modular domestic type Switch box with cover plate, 2 nos of switches of rating 6 Amp and 2 no of sockets ( 6/20 Amps ), suitable for surface mounting as per attached technical specification. |
| 131 | 3 nos. of 1M 16Amp switch, 3 nos. of 6A/16A 2M Shuttered socket (Heavy Duty) , suitable 9M heavy duty polycarbonate box, fire Retardant combined face plate and 3 nos. of 2M Plug Top |
| 132 | 2 nos. of 1M 16Amp switch, 2 nos. of 6A/16A 2M Shuttered socket (Heavy Duty) , suitable 6M heavy duty polycarbonate box, fire Retardant combined face plate and 2 nos. of 2M Plug Top |
| 133 | 1 no. of 6A/16A 2M Shuttered socket (Heavy Duty) and 1 nos. of 1M 16Amp switch suitable 3M heavy duty polycarbonate box, fire Retardant combined face plate and 1 no. of 2M Plug Top |
| 134 | 1 no. of 6A/16A 2M Shuttered socket (Heavy Duty) , suitable 2M heavy duty polycarbonate box, fire Retardant combined face plate and 1 no. of 2M Plug Top |
| 135 | 6 nos. of 1M 6Amp switch and suitable 6M heavy duty polycarbonate box, fire Retardant combined face plate |
| 136 | 4 nos. of 1M 6Amp switch and suitable 4M heavy duty polycarbonate box, fire Retardant combined face plate |
| 137 | 3 nos. of 1M 6Amp switch and suitable 3M heavy duty polycarbonate box , fire Retardant combined face plate |
| 138 | 2 nos. of 1M 6Amp switch and suitable 2M heavy duty polycarbonate box, fire Retardant combined face plate |
| 139 | 1 nos. of 1M 6Amp switch and suitable 1M heavy duty polycarbonate box , fire Retardant combined face plate |
| 140 | SITC of single un-switched weatherproof socket outlet, 6A, 230V AC, suitable for outdoor application, complete with weatherproof enclosure, shuttered socket, 2M plug top, 3pin configuration, IP65 protection, suitable mounting arrangement, terminals and all necessary accessories as per tender technical specification. |
| 141 | Supply and fixing of heavy duty Class-B Galvanised steel (G.I.) ERW conduit pipe of following sizes along with all accessories such as bends, junction box, socket, check nut, etc. including making threads, removing burrs, connection of accessories, cleating with heavy duty GI spacer saddles or suit to site clamps on RCC wall, column, steel structural, etc. as required under the instruction of Engineer-in-incharge. Surface type junction box shall be provided. |
| 142 | 25 MM |
| 143 | 40 MM |
| 144 | Supply of Single Core HFFR wires (Copper) of size mentioned below in voltage grade 1100 V as per the IS 17048: 2018 (latest edition) and as per conductor class 2 of IS: 8130 / 1984 as per technical specification |
| 145 | 1.5 Sq. mm |
| 146 | 2.5 Sq. mm |
| 147 | Installation/drawing through concealled/ surface conduit and wiring and termination at both ends of Single Core HFFR wires (Copper) of size mentioned below in voltage grade 1100 V as per the IS 17048 : 2018. As per conductor class 2 of IS: 8130 / 1984 as per technical specification |
| 148 | 1.5 Sq. mm |
| 149 | 2.5 Sq. mm |
| 150 | Supply and Installation of Casing and Capping of Flame Retardant (FR) PVC material , Ivory Colour, Unplasticised formulation for prolong storage or usage, double lock, ISI Marked as per IS 14927, Highly durability, Resistance to oil and grease of following sizes as required |
| 151 | Size 25mm × 16 mm |
| 152 | Size 38 mm × 16 mm |
| 153 | Size 50 mm × 16 mm |
| 154 | Size 38 mm × 25 mm |
| 155 | Size 50 mm × 25 mm |
| 156 | Size 50 mm × 50 mm |
| 157 | Providing and fabrication of structural steel (IS 2062 E250 BR) supports, bracket etc. with the usage of suitable size angle, channel, strip, plate, pipe, including cutting, welding, fabrication, painting etc. as per tender technical specifications |
| 158 | Supply and Installation of flexible Galvanized steel PVC coated conduit pipe of size 26mm including cleating with heavy duty GI saddles or suit to site clamps on RCC wall, column, steel structure, etc. as required under the instruction of Engineer-in-charge and as per tender specification. |
| 159 | Supply and Installation of flexible Galvanized steel PVC coated conduit pipe of size 50mm including cleating with heavy duty GI saddles or suit to site clamps on RCC wall, column, steel structure, etc. as required under the instruction of Engineer-in-charge and as per tender specification. |
| 160 | Supply of required material and making of straight exothermic braze joints of copper conductors (95 sqmm) as per technical specification. |
| 161 | Supply of required material and making of 'T' type exothermic braze joints of copper conductors (95 sqmm) as per technical specification. |
| 162 | Supply and Installation of GI Anchor Fastner of size M8x80 MM by drilling through concrete block as per site requirement for fixing plate Eps or other structures as per the tender specification. |
| 163 | Supply and installation of GI Anchor Fastner of size M12x130 MM |
| 164 | Supply and Installation of 2mm thick pre-galvanished GI sheet with powder coating including marking,cutting (as per site requirement)and erection on top of JB openings on wall and ceiling at approximate height of 7 mtrs (in size of 150mm ×150mm). |
| 165 | Supply and Installation of Single phase heavy duty exhaust fan of sweep 200 mm with FRP duct suitable for domestic application. |
| 166 | Supply |
| 167 | Installation, Testing and Commissioning |
| 168 | Supply, Installation, Testing and Commissioning of Ceiling mounted dual type occupency sensor with inbuilt or external power pack and auxiliary relay having min 15 mtr sensing range in 180 deg orientation and time delay ranges from 30 sec to 30 min and should have output relay capacity of 1000 W (for LED lighting fixtures) |
| 169 | Supply, Installation, Testing and Commissioning of Occupancy sensor bypass switch box having 3 pole rotary switch fixed on GI enclosure with cover |
| 170 | SITC of Junction box / Cable pull box shall be weather proof type, size 100mm x 100mm x 50mm fabricated out of 2mm thick GI sheet, cable gland plate at bottom, punched hole for conduit entry on all sides, suitable to terminate 2 Nos of 3 core x 2.5 sqmm Cu conductor, 8 Nos of terminals, etc as required |
| 171 | Making the opening in brick masonry for door / window / clear story opening including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface including disposal of mulba/ rubbish to the nearest dumping ground. |
| 172 | Core cutting of 300mm thick RCC slab and hole dia 100mm |
| 173 | Supply and Installation of (M.O.C: Pre-Galvanized G.I sheet steel) powder coated wall mounted PA Main Junction Box (PJB) made of 14SWG, punched hole for conduit entry on all sides and suitable for incoming cable of size 100 pair x 1.5 sq.mm. armoured twisted pair cable. The junction box shall consist of 200 nos. terminals suitable for 1.5 sq.mm. as per the technical specification. |
| 174 | Supply & installation of wall mounted PA Main Junction Box (PJB) fabricated out of 2 mm thick Pregalvanised GI sheet Powder coated, punched hole for conduit entry on all sides and suitable for incoming cable of size 50 pair x 1.5 sq.mm. armoured twisted pair cable. The junction box shall consist of 100 nos. terminals suitable for 1.5 sq.mm. |
| 175 | Supply and Installation of (M.O.C: Pre-Galvanized G.I sheet steel) powder coated wall mounted PA Main Junction Box (PJB) made of 14SWG, punched hole for conduit entry on all sides and suitable for incoming cable of size 20 pair x 1.5 sq.mm. armoured twisted pair cable. The junction box shall consist of 40 nos. terminals suitable for 1.5 sq.mm. as per the technical specification. |
| 176 | Supply & installation of wall mounted PA Main Junction Box (PJB) fabricated out of 2 mm thick Pregalvanised GI sheet Powder coated, punched hole for conduit entry on all sides and suitable for incoming cable of size 10 pair x 1.5 sq.mm. armoured twisted pair cable. The junction box shall consist of 20 nos. terminals suitable for 1.5 sq.mm. |
| 177 | Supply & installation of wall mounted PA Main Junction Box (PJB) fabricated out of 2 mm thick Pregalvanised GI sheet Powder coated, punched hole for conduit entry on all sides and suitable for incoming cable of size 5 pair x 1.5 sq.mm. armoured twisted pair cable. The junction box shall consist of 10 nos. terminals suitable for 1.5 sq.mm. |
| 178 | Supply, drawing/ laying & termination of 25 pair, 1.5 Sq. mm, Flexible, Overall Aluminum Mylar screen with drain wire, Copper, Multistranded conductor, unamoured, FRLS PVC Sheathed (Inner and Outer) as per attached specifications |
| 179 | Supply, drawing / laying & termination of 10 pair, 1.5 Sqmm, Flexible, overall Aluminum Mylar screen with drain wire, Copper, Multistranded conductor, Armoured, FRLS PVC Sheathed (Inner and Outer) as per attached technical specifications |
| 180 | Supply, drawing/ laying & termination of 1 pair, 1.5 Sq. mm, Flexible, Overall Aluminum Mylar screen with drain wire, Copper, Multistranded conductor, unamoured, FRLS PVC Sheathed (Inner and Outer) as per attached specifications |
| 181 | Supply and Installation of Indoor type (M.O.C: Pre-Galvanized G.I sheet steel) powder coated MDF box with krone connector made of 14SWG for 1500+ 1500 pairs of Telephone cable as per the technical specification. |
| 182 | Supply and Installation of Indoor type (M.O.C: Pre-Galvanized G.I sheet steel) powder coated MDF box with krone connector made of 14SWG for 200 + 200pairs of Telephone cable as per the technical specification. |
| 183 | Supply and Installation of Indoor type (M.O.C: Pre-Galvanized G.I sheet steel) powder coated MDF box with krone connector made of 14SWG for 100 + 100pairs of Telephone cable as per the technical specification. |
| 184 | Supply and Installation of Indoor type (M.O.C: Pre-Galvanized G.I sheet steel) powder coated MDF box with krone connector made of 14SWG for 50 + 50pairs of Telephone cable as per the technical specification. |
| 185 | Supply and Installation of Indoor type (M.O.C: Pre-Galvanized G.I sheet steel) powder coated MDF box with krone connector made of 14SWG for 300 + 300pairs of Telephone cable as per the technical specification. |
| 186 | Supply and Installation of Indoor type (M.O.C: Pre-Galvanized G.I sheet steel) powder coated MDF box with krone connector made of 14SWG for 20 + 20pairs of Telephone cable as per the technical specification. |
| 187 | Supply and Laying of 100 Pair, 0.5 mm dia copper conductor, jelly filled armoured telephone cable |
| 188 | Supply and Laying of 50 Pair, 0.5 mm dia copper conductor, jelly filled armoured telephone cable |
| 189 | Supply and Laying of 20 Pair, 0.5 mm dia copper conductor, jelly filled armoured telephone cable |
| 190 | Supply and drawing of 2 Pair 0.5 mm copper conductor Telephone cable from EPABX Main JB upto RJ-11 socket unit of individual telephone instrument through concealed conduit including end termination in RJ-11 socket units. |
| 191 | Supply and Installation of 2Way heavy duty polycarbonate, Fire Retardant, ISI marked Front plate with modular type Four Pin RJ-11 socket unit (with modular PVC box) |
| 192 | Supply & installation of wall mounted Junction box for PA speakers fabricated out of 2 mm thick Pre Galvanised GI sheet steel Powder coated, punched hole for conduit entry on all sides and having 4 way 4 nos. of terminals, suitable for terminating 1.5 sq. mm PA cable. |
| 193 | Supply installation of wall mount and desktope type analog telephone instrument with alphabet and numeriucal caller ID facility. |
| 194 | Supply of 23AWG CAT6 Armoured UTP cable LSZH type |
| 195 | Laying of 23AWG CAT6 Armoured UTP cable LSZH type |
| 196 | Supply of 23AWG CAT6 unarmoured UTP cable LSZH type |
| 197 | laying of 23AWG CAT6 unarmoured UTP cable LSZH type |
| 198 | Supply of 52-port (48x1 Gbps RJ-45 Copper port, 4x1/10 Gbps SFP port) smart web-managed layer-2 network switch with mounting accessories |
| 199 | Installation of 52-port (48x1 Gbps RJ-45 Copper port, 4x1/10 Gbps SFP port) smart web-managed layer-2 network switch with mounting accessories |
| 200 | Supply of 28-port (24x1 Gbps RJ-45 Copper port, 4x1/10 Gbps SFP port) smart web-managed layer-2 network switch with mounting accessories |
| 201 | Installation, testing, commissioning of of 28-port (24x1 Gbps RJ-45 Copper port, 4x1/10 Gbps SFP port) smart web-managed layer-2 network switch with mounting accessories |
| 202 | Supply of Industrial grade 10-port (8x1 Gbps RJ-45 Copper port, 2x1/10 Gbps SFP port) POE+ layer-2 ethernet network switch along with power supply arrangement and mounting accessories |
| 203 | Installation, testing, commissioning of Industrial grade 10-port (8x1 Gbps RJ-45 Copper port, 2x1/10 Gbps SFP port) POE+ layer-2 ethernet network switch along with power supply arrangement and mounting accessories |
| 204 | Supply of 24-Port CAT6 Patch panel of 1U size suitable for 19\\" rack fully loaded with all wiring support accessories inclduing RJ45 connectors. |
| 205 | Installation of 24-Port CAT6 Patch panel of 1U size suitable for 19\\" rack fully loaded with all wiring support accessories inclduing RJ45 connectors. |
| 206 | Supply of Fully Loaded drawout type, LC type 24-port Fiber Distribution (LIU)System of 1U size suitable for mounting in 19\\" rack. |
| 207 | Installation of Fully Loaded drawout type, LC type 24-port Fiber Distribution (LIU)System of 1U size suitable for mounting in 19\\" rack. |
| 208 | Supply of 1Gbps Single Mode (SFP) 1000BASE-LX LC transreciever Module compatible with supplied ethernet switches. |
| 209 | Installationof 1Gbps Single Mode (SFP) 1000BASE-LX LC transreciever Module compatible with supplied ethernet switches. |
| 210 | Supply of 24-core Armoured Single Mode (9/125 um) Multi-tube loosely buffered Fiber optic cable |
| 211 | Laying of 24-core Armoured Single Mode (9/125 um) Multi-tube loosely buffered Fiber optic cable through HDPE pipe. |
| 212 | Supply of HDPE pipe 40 mm along with all accessories like bends, couplers etc, fitting, cutting and jointing etc. |
| 213 | Laying of HDPE pipe 40 mm along with all accessories like bends, couplers etc, fitting, cutting and jointing etc. |
| 214 | CAT6 Patch cords, 1 meter |
| 215 | Supply |
| 216 | Installation |
| 217 | CAT6 Patch cords, 2 meter |
| 218 | Supply |
| 219 | Installation |
| 220 | LC-LC SM Duplex Fiber Patchcords 2 meter length. |
| 221 | Supply |
| 222 | Installation |
| 223 | LC-LC SM Duplex Fiber Patchcords 5 meter length. |
| 224 | Supply |
| 225 | Installation |
| 226 | LC-LC SM Duplex Fiber Patchcords 10 meter length. |
| 227 | Supply |
| 228 | Installation |
| 229 | LC-LC SM Duplex Fiber Patchcords 15 meter length. |
| 230 | Supply |
| 231 | Installation |
| 232 | Fiber optic Splicing and Termination of Connectors |
| 233 | SITC of Indoor IP based 2 MP vandal resistant(IK10) Dome IR camera(POE) along with mounting accessories and junction box |
| 234 | SITC of Outdoor IP based 5 MP Motorised Focused Zoom(MFZ) varifocal IR Bullet camera(POE) along with mounting accessories and outdoor weatherproof junction box |
| 235 | SITC of Outdoor IP based 2 MP WDR IR PTZ(Pan-tilt-Zoom) POE camera (25x or better optical zoom) with mounting accessories and outdoor weatherproof junction box |
| 236 | Supply installation of CCTV 55 inch professional display with necessary wall mounting accessories |
| 237 | Supply installation of HDMI/Display port adaptor with the fiber optic HDMI cable 20 meter length for interface between display and NVR system |
| 238 | Supply of 32-Channel NVR with 1080p resolution support and H.265 or better decoding with minimum 20 TB storage capacity and Supply of Central Video management software along with license for integrated view of NVRs |
| 239 | Installation, commissioning of 32-Channel NVR with 1080p resolution support and H.265 or better decoding with minimum 20 TB storage capacity along with configuration of Central Video management software along with license for integrated view of NVRs |
| 240 | Supply & Installation of 10TB Surveillance grade hard disks compatible with above surveillance system |
| 241 | Supply 9U wall mount network rack of 19\\" size side openable with minimum 2 cooling fans(90 cfm), 5 socket PDU, 2 cable manager and fully loaded with all accessories |
| 242 | Installation, testing, commissioning of 9U wall mount network rack of 19\\" size side openable with minimum 2 cooling fans(90 cfm), 5 socket PDU, 2 cable manager and fully loaded with all accessories |
| 243 | Supply of 9U outdoor IP66 network rack of 19\\" size fully loaded with all accessories |
| 244 | Installation, testing, commissioning of 9U outdoor IP66 network rack of 19\\" size fully loaded with all accessories |
| 245 | Supply of 32U Floor standing rack fully loaded with all accessories |
| 246 | Installation, testing, commissioning of 32U Floor standing rack fully loaded with all accessories |
| 247 | Supply of 24-core armoured cable OFC Splicing jointing kit for cable |
| 248 | Installation of 24-core armoured cable OFC Splicing jointing kit for cable along with OTDR reports |
| 249 | SITC of small form factor/mini PC 16GB RAM/512GB SSD for CCTV surveillance with supply of HDMI/DP connector and 15 meter optical HDMI cable compatible with 55\\" professional display |
| 250 | Supply laying of 32 mm flexible Galvanised steel PVC coated conduit with all fixtures |
| 251 | Supply, installation, testing, commissioning of Key access management system (Minimum 48 Nos. of key) with RFID card access and inbuilt control unit for RFID card enrolment of as per technical specifications. |
| 252 | Excavation in all type of soils of width as specified in the technicals specification at approx. depth of 1000mm below ground level, sand bedding, laying of bricks on side and top,backfilling ,dewatering, consolidation, shoring, disposal of excess earth, Item includes supply of sand and class- 1 bricks Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 26 daysDec 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 27 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender