Tender For Construction Of 30M And 45M Wide Main Roads In Greater Aligarh, Located On Khair Road (Part-A)
Tender Value
15.82 Crore
Estimated cost
Bid Submission
08 Dec 2026
20 days left
EMD
31.65 Lakhs
Bank guarantee accepted
Document Fee
29500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Aligarh → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of 30M And 45M Wide Main Roads In Greater Aligarh, Located On Khair Road (Part-A)
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood,trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared.-DSR-2023/2.31 |
| 2 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.-DSR-2023/ 2.25A |
| 3 | Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with 1⁄2 tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : (a) All kinds of soil-DSR-2023/2.3.1 |
| 4 | Preparation and consolidation of sub grade with power road roller/Vibro roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.-DSR-2023/16.1 |
| 5 | Construction of Granular sub base using crusher run, spreading in uniform layers with mortor grader on prepared surface,mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density,complete as per clause 401. By Mix in Place Method.-Derived from MoRT&H-401 |
| 6 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.Wet Mix Macadam (Plant Mix Method)-Derived from MoRT&H-406 |
| 7 | Providing and applying prime coat with SS1 grade bitumne emulsion on prepared surface of granular base including clearing of road surface and spraying prime at the rte of .70kg/sqm using mechanical means-Derived from MoRT&H-502 |
| 8 | Providing and laying bituminous macadam with higher capacity hot mix plant using crushed aggregates of specified grading, premixed with bitumeneous binder,transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clause 510.6 and 501.7 to achieve the desired compaction-Derived from MoRT&H-504 |
| 9 | Providing and applying Tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.-Derived from MoRT&H-503 |
| 10 | Providing and laying semi dense graded bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder @ 5.0% of mix & filler transported through hot mix to site laying with a hydrostatic paver finisher with sensor control to required grade level and alignment and rolling with smooth wheeled vibratory and tandem rollers as per MORTH specification clause no. 508 complete in all respect-Derived from MoRT&H-504 |
| 11 | Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Enginner- In- charge and accordance with applicable specifications.-DSR-2023/16.62 |
| 12 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineerin- charge.: all kind of soil-DSR-2023/2.6.1 |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)-DSR-2023/4.1.10 |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)-DSR-2023/ 6.1.1 |
| 15 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering: 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stoneaggregate 20 mm nominal size derived from natural sources)-DSR-2023/ 4.1.3 |
| 16 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortor 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer- In- charge (length of finished kerb edging shall be measured to calculate volume for paymets. (Precast C.C Kerb stone shall be approved by Enginner- In- charge)-DSR-2023/16.69 |
| 17 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : (A) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture-DSR-2023/13.62.1 |
| 18 | Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/- 5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.-DSR-2023/16.50 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysDec 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender