Civil Aviation Boards / Undertakings / PSU Closing in 18 days TDR #58564656

Tender For Drain And Paver Block Work Of Back Nine Cart Paths At Cial Golf Club.

Issued by Boards / Undertakings / PSU · Ernakulam, Kerala
Tender Value
5.93 Crore
Estimated cost
Bid Submission
10 Dec 2026
18 days left
EMD
11 Lakhs
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Drain And Paver Block Work Of Back Nine Cart Paths At Cial Golf Club.

BOQ

Name of Work:- Drain and Paver Block Work of Back Nine Cart Paths at CIAL Golf Club.
Sl. No. Item Description
1Clearing grass and removal of the rubbish up to a distance of 5km m outside the periphery of the area cleared.
2Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 5 km outside the periphery of the area cleared.
3Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 min width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 5 km and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil
4Earth work in excavation for all kinds of soil by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 5 km, as per specifications & directions of Engineer-in-charge.
5Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 5 km :All kinds of soil for Pipes, cables etc, not exceeding 80 mm dia.
6Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 5 km :All kinds of soil for Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
7Extra for quantities of earth works, executed in or underwater and/or liquid mud, including cost of pumping or bailing out water and removing slush etc. complete. The unit will be cu.m/metre depth. The quantity shall be measured as the depth measured from the sub soil water level up tothe centre of gravity of the qty executed in difficult conditions multiplied by the quantity executed under subsoil water. The depth shall be reckoned correct to 0.10 m, 0.05 m or more shall be taken as 0.10 m and less than 0.05 m ignored.
8Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m, as per specifications & directions of Engineer-in-charge.
9Filling with available earth (excluding rock) stacked at CIAL premises including excavation and loading with hydraulic excavator, conveyance to site, unloading, spreding of earth layers of thickness not less than 20 cm and consolidating each deposited layer and watering etc for a lead up to 5 Km including cost and conveyance of all labours, lead lifts etc as directed by Engineer-in-charge.
10Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots, reffiling of pits and stacking of serviceable material and disposal of unserviceable material within a lead of 5 km. Beyond 30 cm girth upto and including 60 cm girth
11Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots, reffiling of pits and stacking of serviceable material and disposal of unserviceable material within a lead of 5 km. Beyond 60 cm girth upto and including 120 cm girth
12Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots, reffiling of pits and stacking of serviceable material and disposal of unserviceable material within a lead of 5 km. Beyond 120cm girth upto and including 240 cm girth
13Disposal of excavated earth by mechanical means, including loading, transporting, unloading to approved dumping ground or as approved by Engineer in- charge, beyond 50 m initial lead, for a lead up to 5 km, including all lifts involved.
14Providing and laying in position cement concrete of specified grade, properly mixed and consolidated with hand rammers, including cost and conveyance of all materials, labour, curing, lead, lift, etc., excluding the cost of centering and shuttering, as per specifications & directions of Engineer-in-charge - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
15Providing and laying in position M15 grade cement concrete of specified grade excluding the cost of centering and shuttering-1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) including cost & conveyance of all materials, labour charges, tools machineries rentals etc as directed by Engineer-in-charge All work up to plinth level
16Providing and laying in position machine batched, machine mixed and machine vibrated design mix M-25 grade cement concrete conforming to IS 456 or IS 10262 using cement content as per approved design mix, coarse sand conforming to IS 383 and 20 mm nominal size graded hard granite broken stones, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per specifications and directions of Engineer-in-charge. Minimum cement content is 400 kg/cu.m. No payment shall be made for extra cement used in design mix. All works up to plinth level.
17Extra for laying reinforced cement concrete/plain cement concrete in or under water and/ or liquid mud, including cost of pumping or bailing out water and removing slush etc., complete. Note:- The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and lessthan 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions.
18Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding with binding wire etc. complete including cost, conveyance, lead, lift of all materials for all types of RCC works as per drawing/specifications and as directed by the Engineer-in-charge, for all works upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
19Centering and shuttering including strutting, propping etc. and removal of form, as per specifications and directions of the Engineer-in-charge, for Foundations, footings, bases of columns, etc. for mass concrete.
20Centering and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc
21Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform
22Centering and shuttering including strutting, propping etc. and removal of form work for : Columns, Pillars, Piers, Abutments, Posts and Struts
23Supplying, laying, placing 50mm outer dia (6 kg/cm2) UPVC pipes with necessary arrangements for weep holes in drain, culvert etc as directed by the Engineer-in-charge
24Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer including cost and conveyance of all materials, lead, lift, labour charges, sundries etc. complete as per specifications and as directed by the Engineer-in-charge all complete.
25Steel (Yst 310 Grade) work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete : Electric resistance or induction butt welded tubes including cost and conveyance of all materials, lead, lift, labour charges, sundries etc. complete as per specifications and as directed by the Engineer-in-charge
26Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).
27Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately).
28Painting with synthetic enamel paint of approved brand and manufacture to give an even shade, at all levels, as per specifications and directions of the Engineer-in-charge : Two or more coats on new work
29Scarifying the existing granular road surface including but not limited to Granular Sub Base, Wet mix mecadam, Water bound mecadam extra and disposal of scarified material within all lifts and leads upto 5 km.
30Providing and Constructing subgrade and earthen shoulders with approved material obtained from borrow pits brought from out side wit h all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 etc and complete and as per direction of engineer in charge and as per technical specification clause-305 MORTHRate shall be inclusive of cost and conveyance of all materials inluding red earth, tools labour, loading & unloading charges, rentals, machineries, fuel etc.
31Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge and as per technical specification clause- 401 MORTH With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30Rate shall be inclusive of cost and conveyance of all materials, tools labour, loading & unloading charges, rentals, machineries, fuel etc.
32Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in 75 TPH mechanical mix plant for all leads & lifts, laying in uniform layers with 100 TH mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge as per clause 406 MORTHRate shall be inclusive of cost and conveyance of all materials, tools labour, loading & unloading charges, rentals, machineries, fuel etc.
33Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of 6mm nominal size aggregate, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
34Providing and laying 80mm thick factory made cement concrete interlocking paver block of M-40 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of 6mm nominal size aggregate, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
35Supplying and laying HDPE pipe of dia 140mm (PN 10/PE80) in position for cross drainage purpose across road including cost and conveyance of all materials, labour, electrofusion jointing, all specials as directed by Engineer -in-Charge
36Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 300 mm dia RCC pipes.
37Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia RCC pipes.
38Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 600 mm dia RCC pipes.
39Supplying, laying, jointing and hydro statically testing ISI marked HDPE pipes of 10 kg/cm2 conforming to IS4984: 1985 PE -100 including all fittings and specials such as tees, elbows, bends, reducers, end caps, saddles, plugs, couplings MTA, etc. including the cost of all jointing materials, bolts nuts rubber washers, ferrule, pipe supports, hire of tools, cost of conveyance of water testing, etc. Complete so as to withstand the internal design pressure of 10kg/cm2 etc. complete as directed by Engineer-in-Charge .63 mm dia pipe
40Supplying, laying, jointing and hydro statically testing ISI marked HDPE pipes of 10 kg/cm2 conforming to IS4984: 1985 PE -100 including all fittings and specials such as tees, elbows, bends, reducers, end caps, saddles, plugs, couplings MTA, etc. including the cost of all jointing materials, bolts nuts rubber washers, ferrule, pipe supports, hire of tools, cost of conveyance of water testing, etc. Complete so as to withstand the internal design pressure of 10kg/cm2 etc. complete as directed by Engineer-in-Charge .75 mm dia pipe
41Supplying, laying, jointing and hydro statically testing ISI marked HDPE pipes of 10 kg/cm2 conforming to IS4984: 1985 PE -100 including all fittings and specials such as tees, elbows, bends, reducers, end caps, saddles, plugs, couplings MTA, etc. including the cost of all jointing materials, bolts nuts rubber washers, ferrule, pipe supports, hire of tools, cost of conveyance of water testing, etc. Complete so as to withstand the internal design pressure of 10kg/cm2 etc. complete as directed by Engineer-in-Charge .90 mm dia pipe
42Supplying, laying, jointing and hydro statically testing ISI marked HDPE pipes of 10 kg/cm2 conforming to IS4984: 1985 PE -100 including all fittings and specials such as tees, elbows, bends, reducers, end caps, saddles, plugs, couplings MTA, etc. including the cost of all jointing materials, bolts nuts rubber washers, ferrule, pipe supports, hire of tools, cost of conveyance of water testing, etc. Complete so as to withstand the internal design pressure of 10kg/cm2 etc. complete as directed by Engineer-in-Charge .140 mm dia pipe
43Providing and erecting Cautionary/Mandatory/Informatory signs with 10 years warranty, made out of retro reflective sheeting conforming to Type XI standards of ASTM D 4956 #09 & as per IRC 67-2012 specifications fixed over 2mm thick aluminium sheet, fixing and supplying of frame work including nuts and bolts etc. excluding poles and structural steel. The rate shall include all transportation, scaffoldings, lead lift, labour etc as directed by the Engineer in Charge. (Structural steel frame work, poles, excavation, foundation concrete, synthetic enamel painting shall be paid separately)
44Demolishing cement concrete, nominal concrete 1:3:6 or richer mix, manually/ by mechanical means including disposal of material within 50 metres lead including cost for all tools, labour charges, sundries etc. complete as per specifications and as directed by the Engineer-in-charge
45Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 5km lead including cost for all tools,labour charges, sundries etc. complete as per specifications and as directed by the Engineer-in-charge
46Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 5km lead as per direction of Engineer-in-charge : in Cement mortar
47Disposal of building rubbish/ cement concrete / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved dumping ground or as approved by Engineer-in-charge, beyond 50m initial lead, for a lead upto 5km and all lifts involved.
48Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material within all lifts and lead upto 5 km (by mechanical means).
49Dismantling of sign boards/ advertisment boards of size less than or equal to 3 sqm including excavation and dismantling of foundation concrete , disposal with all lifts and upto a lead of 5 Km and staking the materials Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58564656
AUTHORITY Boards / Undertakings / PSU
TENDER VALUE 5.93 Crore
LAST DATE 10-12-2026
Authority
Authority Name Cochin International Airport Limited
Work Description Tender for Drain And Paver Block Work Of Back Nine Cart Paths At Cial Golf Club.
Basic Detail
Tender No CIAL/CIVIL/604E/E44
Bidding Type Tender
Location
City Ernakulam
State Kerala
Key Dates
Publish Date 17 Nov 2026
Submission Date 10 Dec 2026
Open Date 11 Dec 2026
Finance
Tender Value 5.93 Crore
Tender Fee 5900
EMD 11 Lakhs
Exemption Not Available
Document List
3d12e99f-57aa-4121-9dad-a5259c2a3e19.html
BOQ_1520230.xls
TenderDocumentDrainandPaver.pdf
TenderDrawingsDrainandPaver.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 17, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 10, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 18 days
Dec 11, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 19 days

Tender Documents

Download All (ZIP) ↓
html

3d12e99f-57aa-4121-9dad-a5259c2a3e19.html

xls

BOQ_1520230.xls

pdf

TenderDocumentDrainandPaver.pdf

pdf

TenderDrawingsDrainandPaver.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender