Tender For Construction Of Parking Shed And Laying Of Paver Blocks In The Back Side Of Mahanadi Bhawan, Mero, Cwc, Bhubaneswar (Odisha)
Tender Value
18.63 Lakhs
Estimated cost
Bid Submission
08 Dec 2026
16 days left
EMD
37274
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Khordha → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Parking Shed And Laying Of Paver Blocks In The Back Side Of Mahanadi Bhawan, Mero, Cwc, Bhubaneswar (Odisha)
BOQ
| Sl. No. | Item Description |
| 1 | PARKING SHED |
| 2 | Earth work in excavation by mechanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. All kinds of soil. (Foundation of column footings) |
| 3 | Providing and laying in position cement concrete of specific grade excluding the cost of centering and shuttering - all works up to plinth level: 1:4:8 (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size). (75 mm thick bottom layer of column footing) |
| 4 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering and reinforcement - all works up to plinth level: 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). (Column base 250 mm thick and 500 x 500 mm pedestal, M20) |
| 5 | Steel reinforcement for RCC work including straightening, cutting, bending and placing in position and binding all complete up to plinth level: thermo-mechanically treated bars of grade Fe-500D or more. |
| 6 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. (Columns SHS 150x150x6.0, trusses, purlins RHS 122x61x5.4, eave girders SHS 100x100x4.0, tie runners, bracings and base plates, as per drawings) |
| 7 | Providing and fixing at all heights, levels and locations colour finish aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS 2676, with characteristics of good formability and corrosion resistance. Profile sheets to be fixed to truss members in slope or required pitch with hex cap headed self-drilling/ tapping stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer, all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-in-charge (cost of truss/ frame work paid separately). 0.56 mm aluminium colour coated troughed profile with centre to centre pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000 mm. |
| 8 | Providing and fixing of pre-coated colour or mill finish aluminium roofing accessories in 0.71 mm thickness, alloy 31500 (IS designation) [aluminium alloy AA 3004 (ISO designation)]; coating of 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50 mm with 3 mm thick EPDM seal and SS plain washer complete: |
| 9 | (a) Pre-coated/ mill finish aluminium ridges plain (500-600 mm) |
| 10 | (b) Pre-coated/ mill finish aluminium gutter (600 mm over all girth) |
| 11 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete - anchor bolts (4.6, M24, 800 mm long) |
| 12 | LAYING OF PAVER BLOCK |
| 13 | Providing and laying factory made chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as per direction of Engineer-in-charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design and pattern. |
| 14 | OTHER MISC. WORKS |
| 15 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth up to 50 m lead and lift up to 1.5 m, as directed by Engineer-in-charge. All kinds of soil. (Foundation of 250 mm thick protection walls, east and south sides) |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand). (250 mm thick protection walls, east and south sides) |
| 17 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 m lead as per direction of Engineer-in-charge. (Block A) |
| 18 | Cleaning of choked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150 mm dia up to 300 mm. |
| 19 | Dismantling steel work in built up section in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 m lead. (Two small existing parking sheds, at lump sum) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysDec 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender