Rural Development Government Departments Closing in 8 days TDR #58562548

Tender For Construction Of Road From Chatargada (Chamarpada) To Kisanpada Road

Issued by Government Departments · Sambalpur, Odisha
Tender Value
5.65 Crore
Estimated cost
Bid Submission
01 Dec 2026
8 days left
EMD
5.65 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Sambalpur → Odisha
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Construction Of Road From Chatargada (Chamarpada) To Kisanpada Road

BOQ

Name of Work:- Construction of road from Chatargada (Chamarpada) to Kisanpada Road
Sl. No. Item Description
1Clearing and grubbing road land in area of light jungle including uprooting rank vagetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of tress cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned upto a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness including watering and cost of labour, cess & all materials etc. complete as per direction of Engineer - in - charge.
2Construction of embankment with approved material obtained from borrow pits (excluding all lifts and leads & transporting to site) spreading, grading to required slope & compacting to meet requirement of table 300-2 & Clause 305 of MoSRT&H Specification of Road & Bridge works (4th Revision)
3Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2.
4Construction of granular Sub base by providing close grade granular sub-base grading-III material as per table-100-1. spreading in uniform layers with motor grader om prepared surface,mixing by mix in place method with rotavator at OMC and compacting with vibratory roller to achieve the desired density complete as per clause 401 of MOSRT&H specifications for road and Bridges work.
5Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.
6Construction of un-reinforced, plain cement concrete pavement over a prepared sub-base with 43 grade cement @ 400kg per cum, coarse and fine aggregate conforming to IS:383, maximum size of coarse aggregate not exceeding 25mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures, as approved, curing compound, finishing to lines and grades as per drawing and as per clause 602 of MOSRT&H Specifications for Road & Bridges work (4th Revision).
7Fine dressing and turfing with one extra lead of 50m and 1.5m one extra lift as per Sepification and direction of Engineer-in-charge.
8Earth work in excavation of fondation in hard soil within the initial lead & lift including dressing & levelling the bed & depositiong the excavated earth away from the site etc. all complete as per the direction of Engineer in Charge.
9Filling sand-Supplying & filling good clean river sand of approved quality including watering to complete saturation & ramming complete with all leads & lifts including cost, conveyance, royalty & taxes of all materials & cost of all labour & T&P required for the work etc. complete as per specification & direction of Engineer in charge.
10Plain cement concrete M-15 grade in Foundation complete as per drawing and technical specification.
11Plain cement concrete M-15 grade in Sub-Structure complete as per drawing and technical specification.
12Providing Weep Holes is Brick Masonry/Paln/Rainforced concrete abutment, wing wall / return wall with 100mm dia AC pipe, extending through the full width of the structure wirh slope of IV:2Htowards drawing force etc, complete.
13R.C.C work of M-25 grade with 20mm and down grade black hard granite (crusherbroken) stone chips including cost, conveyance, royalty & taxes of all materials & cost of all labour & T&P required for the work etc. complete as per specification & direction of Engineer in charge.
14Supplying, fitting and placing HYSD bar reinforcement (Fe 415) complete as per drawings and MORD technical specification Clauses 1000,1200 as per direction of the Engineer in charge
15Providing laying R.C.C Hume pipe NP3 class for culverts including fixing collar with cement mortar 1:2 but excluding excavation, protection work, backfilling, concrete and masonary work in head walls and parapets clause 1106 of MORD specification for Rural roads and as per irection of Engineer-in charge.1000 mm dia Single row
16Providing and Laying Cutting edge of Mild Steel weighing 40 kg per metre including cladding for Well foundation etc. complete as per drawing and technical specifications.
17Labour for sinking in all kinds of soil other than rock in lines plumb etc complete. For 7.50 mtr dia Well
18For 6.50 mtr dia Well
19Sinking of R.C.C well sinking in soft rock (Non coring)/ Boulder/ Hard Soil )(wherein SPT>100) to lines levels & plum by scooping out from inside and below the steining including cost of hire and running charges of tools and plants and supplying & working of pumps bailing out of water and removal of all materials and obstacle from inside the well by divers etc. including precaution against shifting and lifting disposal of the soil with all leads and lift etc. complete as directed by the Engineer-in-charges. For 7.50 mtr dia Well
20For 6.50 mtr dia Well
21Construction of R.C.C well sinking in soft rock to lines levels & plumb by scooping out from inside and below the steining including cost of hire and running charges of tools and plants and supplying & working of pumps bailing out of water and removal of all materials and obstacle from inside the well by divers etc. including precaution against shifting and lifting disposal of the soil with all leads and lift etc. complete as directed by the Engineer-in-charges.For 7.50 mtr dia Well
22For 6.50 mtr dia Well
23Construction of R.C.C well sinking in Hard rock to lines levels & plumb by scooping out from inside and below the steining including cost of hire and running charges of tools and plants and supplying & working of pumps bailing out of water and removal of all materials and obstacle from inside the well by divers etc. including precaution against shifting and lifting disposal of the soil with all leads and lift etc. complete as directed by the Engineer-in-charges.For 7.50 mtr dia Well
24For 6.50 mtr dia Well
25Earth work excavation in foundation in Hard and compacted sheet rock within all leads and lifts including shoring, shuttering, propping bullahs, piling, dewatering from the foundation, supply & working of pumps stacking the excavated material away from the work in site.
26Reinforced Cement Concrete M 25 Grade using 20mm down graded chips in Foundation and Plinth. WELL CURB
27WELL STEINING
28RCC Crash barrier of M40 Grade
29Plain Cement Concrete M 20 Grade using 20mm down graded chips in superstructure. WELL STEINING
30Reinforced Cement Concrete M 30 Grade using 20mm down graded chips in superstructure. WELL CAP
31Abutment & Pier Shaft
32Abutment & Pier Cap
33DIRT Wall
34Superstructure
35Approach Slab
36Wearing Coat - Mastic Asphalt
37Straightening, cutting, bending binding M/S or T.S. rods and placing in position etc. complete
38Providing and laying of Filter media with stone crushed aggregates of 45 mm size satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment , wingwall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specifications.
39Rough stone dry packing in approns and revetments with hard granite stone (30 cm & above) including cost of all materials etc complete
40Back filling behind abutment, wing wall and return wall complete as per drawing and technical specification.GRANULAR MATERIAL
41Boulder Filling with Sand grouted
42In abutment/ pier wells with sand
43Providing and fixing 15 cm dia & 1.00m long RCC Guard posts including all costs & conveyance etc complete.
44Providing fitting and fixing of expansion joint Fixing of Strip Seal Expansion Joint
45Providing Cement Concrete (1:3:6) etc complete
46Supply and fixing of the POT / PTFE Bearing procured from approved manufacturer & with test certificates as per specification provided in drawing at location with all accessories complete & fixing on abutment and piers in position with all materials, labour, tools, equipment for fixing as per drawings and technical specifications part I/II, section 2000 & its relevant clauses & sub clauses of MoRTH specification for Road & Bridge works (4th revision) as directed by Engineer/or his representative to satisfaction.
47Supplying, fabricating welded water tight drainage spout assembly to dimensions shown on drawing of dia not less than 100mm dia with Ggalvanized steel confirming to IS 226 & fixing in position with suitable fixures at specified location on bridge decks including painting two coats with bituminous paint sealant as per IS 1834 around the spout to the deck slab as per technical specification part I/ II of Clause-2705 under Section 2700 of MORT&H specifications for Road & Bridge works (5th Revision) and as per direction of Engineer-in-Charge.
48Fixing of anchoring bars upto 25mm to 38mm dia in foundation rock in abutments and piers including drilling holes, fixing wedged anchors and grouting with cement mortar 1:4 complete as per the direction of Engineer in charge excluding cost of M.S. rods .
49Levelling the hard rock surface under wells for piers, abutments & wing under water
50Providing and applying two coats of water based enamel paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescense and applying paint @ 1 litre per 02 Sqm
51Add for SBY Informatory sign board of 12' 0\\" x 8' 0\\" size
52ROAD SIGNAGE Information Sign Board
53Citizen Board
54Direction & Place Identification Board
55Fixing of road cautionary Sign 600mm equilateral triangle
56600mm Circular
57Fixing of 5th KM stone Fixing of Ordinary KM stone
58Fixing of 200 metre stone
59Guide Post
60Restoration of rain cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh material in layers not exceeding 250 mm and compaction with plate compactor or power rammer to restore the original alignment, level and slopes as per drawings and technical specifications Clause 1902 of MoRD by manual means and as per the direction of the Engineer in charge 1st year
612nd year
623rd year
634th year
645th year
65Maintenance of earthen shoulder (filling with fresh selected soil) Making up loss of material/irregularities on shoulders to the design level by adding fresh approved selected soil and compacting it with appropriate equipment at OMC upto a lead of 1000 m as per technical specification Clause 1903 of MoRD and as per the direction of the Engineer in charge 1st year
662nd year
673rd year
684th year
695th year
70Stripping excess soil from the shoulder surface to achieve the approved level and compacting with plate compactor at OMC as per MORD Techinical Specification Cluase 1903 & direction of Engineer-in-charge.1st year
712nd year
723rd year
734th year
745th year
75Repair to pot holes and removal of loose material, trimming of sides, cleaning of surface by providing tack coat, 20 mm thick pre-mix carpet and seal coat type C as per MORD technical specification Clause 503,508,510,1904 as per direction of the Engineer in charge.1st year
762nd year
773rd year
784th year
795th year
80Maintenance of road signs by way of cleaning and repainting of mandatory / requlatory / cautionary / informatory and place identifications sign board as perdrawings and technical specification Clause 1910 of MoRD & direction of Engineer-in-charge. 1st year
812nd year
823rd year
834th year
845th year
85Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908 of MoRD & direction of Engineer-in-charge.1st year
862nd year
873rd year
884th year
895th year
90Maintenance of 200 metre km stone by way of refixing of tilted stones repairing with cement mortar, cleaning, repairing and lettering on 200 metre km stone and 5th km stone as per drawing and technical specification Clause 1912 of MoRD & direction of Engineer-1st year
912nd year
923rd year
934th year
945th year
95Cutting of branches of trees from the road way or with in R.O.W including disposal of wood and leaves to suitable location as per technical specification Clause 1914 of MoRD & direction of Engineer-in-charge.1st year
962nd year
973rd year
984th year
995th year
100Cutting of shurbs from the roadways or within ROW including clearing away from site etc complete as per drawing & MORD Techinical Specification Cluase 1914 & direction of Engineer-in-charge.1st year
1012nd year
1023rd year
1034th year
1045th year
105Triming of grass & weeds from the roadways or with ROW including clearing away from site etc complete as per drawing & MORD techinical specification Cluase 1914 & direction of Engineer-in-charge.1st year
1062nd year
1073rd year
1084th year
1095th year
110White washing two coats on parapet walls and tree trunks including preparation of surface by cleaning scraping etc. as per technical specifications Clause 1915 of MoRD & direction of Engineer-in-charge.1st year
1112nd year
1123rd year
1134th year
1145th year Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58562548
AUTHORITY Government Departments
TENDER VALUE 5.65 Crore
LAST DATE 01-12-2026
Authority
Authority Name Rural Works Department
Work Description Tender for Construction Of Road From Chatargada (Chamarpada) To Kisanpada Road
Basic Detail
Tender No ROAD TENDER ONLINE RWCSBP-30 OF 2026-27
Bidding Type Tender
Location
City Sambalpur
State Odisha
Key Dates
Publish Date 17 Nov 2026
Submission Date 01 Dec 2026
Open Date 02 Dec 2026
Finance
Tender Value 5.65 Crore
Tender Fee 10000
EMD 5.65 Lakhs
Exemption Available
Document List
0eca98f2-6097-4544-8c2a-7f93202bfdf6.html
BOQ_621646.xls
Tendernotice_1.pdf
Tendernotice_2.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 17, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 01, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 8 days
Dec 02, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 9 days

Tender Documents

Download All (ZIP) ↓
html

0eca98f2-6097-4544-8c2a-7f93202bfdf6.html

xls

BOQ_621646.xls

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender