Defence Statutory Bodies & Commissions/Committees Closing in 21 days TDR #58553394

Tender For special Repair To Bldg No P-98 (Or Govt Md Accn) At Sanjay Vihar (Hudson Lines) Of Afmsd Lucknow Under Ge (East) Lucknow

Issued by Statutory Bodies & Commissions/Committees · Lucknow, Uttar Pradesh
Tender Value
38.82 Lakhs
Estimated cost
Bid Submission
07 Dec 2026
21 days left
EMD
77640
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Lucknow → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for special Repair To Bldg No P-98 (Or Govt Md Accn) At Sanjay Vihar (Hudson Lines) Of Afmsd Lucknow Under Ge (East) Lucknow

BOQ

Name of Work:- SPL REPAIR TO BLDG NO P-98 (OR GOVT MD ACCN) AT SANJAY VIHAR (HUDSON LINES) OF AFMSD LUCKNOW UNDER GE (EAST) LUCKNOW
Sl. No. Item Description
1Demolition of cement concrete (unreinforced) in any position n.exc 15 cm thickness below and above ground level complete all as specified and directed.
2Demolition of cement concrete (unreinforced) of any description and in any position as in roofs, floors (other than ground floors) and similar works.
3Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles.
4M & L for brick work using old size fly ash brick, straight or curved on plan exc 6m mean radius, built in CM (1:6), complete all as specified and directed.
5All as item No 4 above but except bricks (old serviceable bricks retrived from demolition and stacked after cleaning shall be used under this item.)
6M & L for brick work with old size fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4, complete all as specified and directed.
7Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.
8M&L for Self Curing Ready Mix Plaster of thickness 12 mm to 15 mm, pre-packaged, ready-to-use formulated with cement, graded sand, polymers, and special self-curing compounds on external surfaces of walls, chajja, facia at any height with necessary scafolding surface finished even and smoothcomplete as per the direction of Engineer-in-Charge.
9M&L for Self Curing Ready Mix Plaster of thickness 10 mm to 15 mm, pre-packaged, ready-to-use formulated with cement, graded sand, polymers, and special self-curing compounds on Internal surfaces of walls, at any height with necessary scafolding surface finished even and smooth complete as per the direction of Engineer-in-Charge.
10Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm Note- Primer and emmulsion to be carried out through air less spray machine (Mechanical means)
11M & L for preparation of surfaces and applying two coat of oil bound distemper with roller on New surface of wall with Primer etc. complete all as specified and directed.
12M&L for Self Curing Ready Mix Plaster of thickness 5mm to 8 mm , pre-packaged, ready-to-use formulated with cement, graded sand, polymers, and special self-curing compounds on Internal surfaces of Ceiling, chajja, facia at any height with necessary scafolding surface finished even and smooth complete as per the direction of Engineer-in-Charge.
13Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and directed.
14M & L for Providing and applying minimum 1mm thick wall care putty over prepared surface to achive the surface even and smooth for painting.
15M&L for preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete all as specified and directed.
16M&L for preparation of old decorated plastered surfaces of ceilling and applying one coat of white washing on ceilling complete all as specified and directed.
17M & L for preparation of old previously treated surfaces of walls and applying one coat of white wash on walls complete all as specified and directed.
18M&L for applying three coat of white wash including preparation new plaster surface on wall, complete all as specified and directed.
19Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.
20M&L for coloured non skid edge cut (joint free) premium quality ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 sqm but n exc 0.11 sqm, in floors etc set and jointed in white or coloured cement to match laid over 15mm thick screed in CM 1:4 complete all as specified and as directed.
21M&L for non skid coloured premium quality ceramic tiles, joint free 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.36 sqm in floors with borders, incl over 15mm thick screed bed in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors complete all as specified and directed.
22M&L for glazed ceramic premium quality tiles (coloured) 600x300x7-8mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, complete all as specified and as directed.
23Dismantling of stone slabs and tiles laid in bedded cement mortar of any description or thickness in floors, aprons etc, complete all as specified and directed.
24M&L machine cut kota stone slab flooring 20-25mm thick laid over and including 15mm screed bed (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing rounding edge and including glossy smooth polish on Kota slab stone by using carborandum stone (at least three cuttings) complete all as specified and directed by Engineer-in-charge.
25All as per item No 24 above but except stone.
26All as per item No 24 above but on vertical surface such as dado, skirting etc over 10 mm thick skirting in CM 1:4
27M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound Grade A complete all as specified and directed.
28M & L for forming construction joints 30 mm deep x 10mm wide filled with sealing compound grade \\"A.\\" complete all as specified and directed.
29M&L for 18-20mm thick black / green granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like, over 20mm thick screed bed in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite, complete all as specified and directed.
30Rounding of edges of stone slabs one edge smooth round with polishing to match the finish of granite at top such as in steps, cooking platform, and other similar situations including making hole for gas pipe complete all as specified and directed.
31Supply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 Kgs/Sqm laid on a coat of bitumen primer @ 0.30 to 0.50 kg per Sqm for sunken tratment complete all as specified and directed.
32Taking down loose filling of aggregate in any form from sunken slab and refiiling after treatment complete all as specified and directed.
33Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc. all as directed.
34Taking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, trenches etc. all as directed.
35M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls.
36M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.
37Fixing only 15mm bore tubes \\"medium grade \\" galvanised with all fittings and fixed complete to walls and ceilings or laid in floors.
38M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.
39Fixing only 20mm bore tubes \\"medium grade \\" galvanised with all fittings and fixed complete to walls and ceilings or laid in floors.
40S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.
41S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.
42S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.
43S&F sink made of stainless steel 0.8mm thick stainless steel non scratchable for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 600mm x 460 mm with bowl size 590mm x 430mm x160 mm including 40mm bore PVC waste fitting suitable for sink with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink complete all as specified and directed.
44S & F stainless steel kitchen plate rack of overall size 750 mm x 600 mm and 250 mm deep, stainless steel non scratchable with partitions for small/large plates etc made out of stainless steel 0.63 mm thick fixed with rawl plug and CP steel screws complete, all as specified and directed.
45S&F CP grating 125mm dia with waste hole complete all as specified & directed.
46S&F CP grating 125mm dia without waste hole complete all as specified & directed.
47S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified & directed.
48S&F in repairs long body 15mm bore bib tap, fancy type, chromium plated, cast copper alloy, with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.
49S&F in repairs CP angle valve, fancy type long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate complete all as specified & directed.
50S&F in repair 15mm bore concealed type, stop valve cast copper alloy screwed down high pressure with capstan head and cup, screwed both ends for iron pipe or for union all as specified.
51S&F in repair 15mm bore pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes, complete all as specified & directed.
52S & F for 5 mm thick glass Corner shelf 300mm with chromium plated guard, fixed with brass screws and wooden/plastic cleats complete all as specified and directed.
53S&F in repairs CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified.
54S&F 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor, complete all as specified and directed.
55S&F in repair 600mm x450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial Ply wood backingfixed to wooden plugs with chromium plated brass screws and cup washer, complete all as specified and directed.
56S&F in repairs brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified.
57Dismantling RCC/PVC water tanks and removing for capacity exceedin 250 litres & not exceeding 500 litres etc., all as directed.
58S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks, white colour, Triple layered (cylindrical, vertical with closed top) hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete, all as specified and directed.
59S&F 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, all as specified.
60S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore, all as specified and as approved by GE/Engineer-in-Charge.
61S&F PVC coated 25mm dia Mild steel pipe as in curtain rods includin brackets and fancy type end knobs, complete, all as specified and directed.
62Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding, complete.
63S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.
64S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.
65S & F PVC (SWR) floor trap of size 110/110mm, complete all as specified and directed.
66S & F for 110mm PVC (SWR) WC connector bent type, complete all as specified and directed.
67S&F 110mm bore PVC (SWR) bend, any radius, complete all as specified and directed.
68S&F 75mm bore PVC (SWR) bend, any radius with access door, complete all as specified and directed.
69S&F 75mm bore PVC (SWR) bend, any radius, complete all as specified and directed.
70S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.
71Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each, complete, all as specified & directed.
72Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete, all as specified & directed.
73S&F 2nd class hard wood plain(SAL), solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as specified.
74M&L plain cement concrete cast in situ 1:3:6 type C1 using 20 mm graded stone aggregate as in copings, hold fast, back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work complete all as spcefied and directed
75S&F pressed steel frame for door with one or more rebates size 125x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast etc. complete all as spcefied and directed
76S&F pressed steel frame for door with one or more rebates size 105x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast, etc.complete all as spcefied and directed
77S&F for 30mm thick factory made flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides, complete all as spcefied and directed.
78S & F for 35mm thick factory made glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.
79M&L for in repair block board, 19/20mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame work as in cup board shutter/shelves/cabinet etc, complete, all as specified and directed.
80M&L for 0.90mm thick decorative laminates 'Mica type 1 of surface finished,colour and pattern as approved, fixed with adhesive as per makers instructions complete, all as specified and directed.
81S&F in repair kitchen cabinet shutter with frame including shelves, drawer made of solid PVC Block board18/ 19 mm thick one sides decorative face and balance side white having smooth outlet integral skin are made and shall be fixed to walls using required size sheet metal screw and solvent adhesive vertical and horizontal profile made of PVC 18/19mm solid board profile complete all as specified by manufacturer instruction complete, all as specified and directed.
82M&L for external teak wood lipping, 6mm thick fixed with nail, complete all as specified and directed.
83M&L magnet ball catcher for cup board shutters, complete all as spcefied and directed.
84S&F for clip type stainless steel SS 304 grade self closing hinges for cabinets fitted with cadmium coated screws all as specified and directed.
85M & L for 100mm size stainless steel fancy type handle, complete all as specified and directed.
86S & F for 100 mm long Hasp & staple, safety type, Stainless steel with mild steel hinges pin including bolt to hinges plate & fixed with screw, complete all as specified and directed.
87S&F PVC solid door frame of size 50x47mm made out of 5m plain coloured sheet reinforced with MS square tube & with wood grain printed complete all as specified and directed.
88S&F for factory made soild PVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner & supplying & fixing in frame at site as per pecifications & drawing.
89S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified.
90S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified.
91S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified
92S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified.
93S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.
94Dismantling of steel windows/ventilators withot taking off shutters, complete all as specified and directed.
95S& F of windows / Vintelator made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick \\"D\\" Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyster paint of 12-16 microns thick and back coated with 5-7 microns thick alkyed backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52x25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap.approved stay, handles 2nos of heavy duty stainless steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10 mm square guard bars with 6\\"(152.4mm) pitch, complete for finished item of work including of all taxes complete all as specified & as directed.Note : Size of window / ventilator shall be provided by EIC during execution of work.
96S&F mild steel framed work such as grills, guard bars, barred iron doors, cooler stand, framework of water tanks and similar works, conforming to Grade E-165 (Fe 290), including welding etc. complete all as specified & as directed.
97S&F for stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples all as specified.
98M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.
99M&L for preparation of new steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified and direced.
100M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.
101M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.
102Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.
103M&L for cement concrete (1:3:6) type C1 using 20 mm graded crushed stone aggregate as in surface channels, drains, coping and benching including necessary formwork whrever required. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.
104Dismantling of stone slabs and tiles laid in dry of any description or thickness in floors, aprons etc. complete all as specified and directed.
105M & L for 60mm thick pressed precast concrete interlocking paver block moulded rubberiesd reflective type, rubber moulded coloured of M-35mm grade laid over and including 25 mm thick sand cushion as in floorsand corners at edges shall be sealed with PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate complete all as specified and directed.
106All as per item No 105 but excet paver block.
107M & L for sand filling in floors or pavings, laid in layers n exc. 15 cmthick, spread, levelled and rammed including watering complete all as specified and directed.
108Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed
109M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Chhajjas, cover slab, shelves and similar articles set in CM 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately
110M&L for TMT bars 10mm dia and over cut to length, bent to shape required including cranking and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.
111Dismantling brick tiles or terracing tiles, single layer of roofs including demolition and removing of mud in roofs any thickness including plastering and leeping (whether full thickness removed or part thereof ) and demolition material disposed out from MoD land and including roughening surfaces of old concrete by picking, sweeping/Brushing clean and washing down with water to remove dust and apply neat cement slurry with 3.0kg of cement per sq. metre complete all as directed.Note : (a) Rubbish including mud phuska shall be removed from site to a distance of 1.5 KM out side MOD land at thier own arrangement. (b) U/S brick tiles shall be credited to contractor under Sch of credit.
112M & L PCC 1:2:4 type B-0 (using 12.50mm graded stone aggregate) as in roof kerbs/roof padding /benching or mud stops, and platform for mounting service tanks, rounded, chamfered on edges including necessary use and waste of from work etc and mixed with liquid water proofing compound @200ml per 50 Kg cement bag etc all as specified and directed.Note : Liquid WPC shall be measured and paid seprately.
113M & L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- 1. Application of high perfomance hybride polyurea elastomeric water proofing coating cold applied, liquid membrane at 1.5 kg/Sqm with an elongation minimum of 500+100% by airless spray machine and tensile strength of minimum 11-13 N/mm2 as per ASTM D2370, crack bridging ability minimum of 3 to 4 mm as per ASTM C1305 , Shore Hardness of minimum 70+5 as per ASTM D2240 complete as per directed by Engr-In-Charge. The System shall also include final base preparation including cleaning of the plaster surface etc and applying epoxy primer as approved makes in two coats at a coverage of 1 kg/Sqm, etc as per manufacturer specification, complete all as specified and directed. 2. Cool roof Tile 300 x 300 x 20mm thick Tile satin matte finish colour white , anti skid surface for roof over 20mnm thick CM 1:4 screed bed Note:- (i) All quantity of material, paint, primer & PU Paint , whatever is specified by the OEM as the manufacturesv instruction shall be deposit with Engr-in-Charge.(ii) Irrespective of whatever specified elsewhere in tender documents, the work shall be got executed through authorized executor of approved manufacturer’s only. The tri-party agreement between contractor, approved manufacturer and their authorized Applicator on Non Judicial Stamp paper of Rs 100/- shall be submitted before execution of work for approval of GE. (iii) Work will be executed only ofter approval aforesaid MoU.
114M & L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- 1. Application of high perfomance hybride polyurea elastomeric water proofing coating cold applied, liquid membrane at 1.5 kg/Sqm with an elongation minimum of 500+100% by airless spray machine and tensile strength of minimum 11-13 N/mm2 as per ASTM D2370, crack bridging ability minimum of 3 to 4 mm as per ASTM C1305 , Shore Hardness of minimum 70+5 as per ASTM D2240 complete as per directed by Engr-In-Charge. The System shall also include final base preparation including cleaning of the plaster surface etc and applying epoxy primer as approved makes in two coats at a coverage of 1 kg/Sqm, etc as per manufacturer specification, complete all as specified and directed. Note : Same as above mentioned in item No 113 above.
115Taking down carefully existing surface aluminium or copper point wiring (light, fan, socket, bell or power) including all associated fixtures and fittings such as switches, ceiling roses, regulators, sockets, lamp/angle holder etc and making good the disturbed surfaces to an even and smooth finish using cement mortar 1:3 and applying white/colour wash to match the existing surface complete.
116M&L for point wiring with 1100 Volts grade PVC insulated FRLS multi-stranded copper conductor cable 1.5 sqmm including PVC insulated FRLS copper earth continuity conductor 1.5 sqmm, colour-coded as per IS, drawn through and including concealed rigid non-metallic PVC conduit, medium grade, ISI marked, ivory colour of size not less than 25 mm dia with all necessary conduit fittings and accessories such as bends, tees, couplers, junction boxes etc including concealed sunken modular GI metal boxes of minimum 1.0 mm thickness with modular mounting cover plates and frames of approved colour, suitable for mounting modular switches, sockets, regulators, etc complete for the following:– One light point controlled by one switch.
117All as per item No 116 but One fan point controlled by one switch.
118All as per item No 116 but One light point controlled by two, two way switches.
119All as per item No 116 but One socket outlet 6 Amp controlled by one switch on the same board with other switches.
120All as per item No 116 but One socket outlet 6 Amp controlled by one switch on indepdendent board.
121All as per item No but 116 One bell point controlled by one bell push.
122M&L for point wiring with 1100 Volts grade PVC insulated FRLS multi-stranded copper conductor cable 2.5 sqmm, including PVC insulated FRLS copper earth continuity conductor 2.5 sqmm, colour-coded as per IS, drawn through and including concealed rigid non-metallic PVC conduit, medium grade, ISI marked, ivory colour, of size not less than 25 mm dia, with all necessary conduit fittings and fixing accessories, including sunken GI metal box of minimum 1.0 mm thickness with modular mounting cover plate and frame of approved colour, suitable for mounting modular accessories, complete for one 6A or 16 A socket outlet point controlled by one switch on independent board.
123M&L for point wiring with 1100 Volts grade PVC insulated FRLS multi-stranded copper conductor cable 4 sqmm, including PVC insulated FRLS copper earth continuity conductor 4 sqmm, colour-coded as per IS, drawn through and including concealed rigid non-metallic PVC conduit, medium grade, ISI marked, ivory colour, of size not less than 25 mm dia, with all necessary conduit fittings and fixing accessories complete for one 16A/20A socket outlet point controlled by one module MCB on independent board.
124S&F modular angle lamp holder, of approved make with insulated polycarbonate body with modular frame including necessary fixing accessories and electrical connections complete.
125S&F modular one-way switch, 6 Amp, 1-module size of approved make, with all necessary fixing accessories and electrical connections complete.
126S&F modular one-way switch, 16 Amp, 1-module size, of approved make, with all necessary fixing accessories and electrical connections complete.
127S&F modular two-way switch, 6 Amp, 1-module size of approved make with all necessary fixing accessories and electrical connections complete.
128S&F modular bell push switch, 6 Amp, 1-module size of approved make with all necessary fixing accessories and electrical connections complete
129S&F AC door bell, 240 Volts, single pole of approved mak with all necessary fixing accessories and electrical connections complete.
130S&F modular socket outlet, 6 Amp, 2/3 pin combined, 2-module size, of approved make with all necessary fixing accessories and electrical connections complete.
131S&F modular socket outlet, 6/16 Amp, 2/3 pin combined, 2-module size, of approved make with all necessary fixing accessories and electrical connections complete.
132S&F MCCB, four-pole, 125 Amp, with minimum breaking capacity 16 kA (Icu = Ics), thermally adjustable type with thermal overload setting range from 70% to 100% of rated current, and fixed magnetic short-circuit protection, with spreader links (set of four) for cable connections, suitable cable lugs, nuts, bolts and washers including making all electrical connections complete.
133S&F of MCB Distribution Board, factory-assembled type, fabricated from powder-coated CRCA steel sheet, recess-mounted, complete with reversible double door, having a minimum degree of protection IP-43 and mechanical impact resistance IK-09, conforming to IS 61439 (Low-voltage switchgear and controlgear assemblies), provided with insulated tinned copper busbar of 100 Amp rating, separate neutral busbar and earth busbar, DIN rail, detachable gland plate, complete with all internal interconnections, earthing connections, and blanking plates for all unused ways/spaces, complete in all respects, suitable for the following ratings and number of ways:–SPN, 240 volts, 8 ways.Note: MCCBs, MCBs and MCB Distribution Boards (DBs) shall be of the same make to ensure proper coordination, compatibility and compliance with applicable IEC standards. Mixing of makes shall not be permitted.
134S&F ceiling rose, 3-plate type, with insulated polycarbonate body, of approved make with all necessary fixing accessories and electrical connections complete.
135M&L for sub-main wiring along with earth continuity conductor, using PVC insulated FRLS, multi-stranded copper conductor cables, colour-coded, drawn into and including concealed rigid non-metallic PVC conduit, medium grade, ISI marked, ivory colour, complete with all conduit accessories such as bends, tees, junction boxes, inspection boxes, saddles/clamps etc including cutting chases, making good disturbed surfaces to match existing finish complete in all respects of the following nominal sizes:–2x4 sqmm + 1x4 sqmm earth wire in 20 mm dia conduit.
136All as per item No 135 above but 2x6 sqmm + 1x6 sqmm earth wire in 25 mm dia conduit.
137S&F of MCBs of ‘C’ series, with breaking capacity 10 kA, ISI marked, complete with making wiring connections using suitable size copper lugs, tightening, testing and commissioning, installed inside MCB distribution boards complete in all respects of the following current ratings:–SP 6 to 32 Amp.
138All as per item No 137 above but SPN (or DP) 32 A.
139S&F GI pipe bracket, 32 mm dia, light grade, 1.2 m long, bent to shape for security light fitting including 2 Nos MS clamps with nuts, bolts & washers and painting of clamps with aluminium paint over one coat of red oxide primer complete.
140S&F LED security light fixture 25 to 35 Watt with powder-coated pressure die-cast aluminium body complete with electronic driver suitable for input voltage 140–270 Volts AC, 50 Hz, operating temperature –15°C to +50°C, provided with internal surge protection minimum 5 kV (L–N–E) as per IEC 61000-4-5, driver efficiency >85%, THD <10% as per IEC 61000-3-2, power factor ≥0.95, IP-66 protection and IK-10 impact resistance, CRI >80, system lumen efficacy ≥105 and <120 lm/W, with under-voltage and over-voltage protection, EMI/EMC compliance as per CISPR-15, and optical lenses for beam angle as per IESNA Type I / II / III, as required. The luminaire shall have minimum rated life of 50000 burning hours for LED with 70% lumen maintenance at end of life supported by LM-80 extrapolation and IES TM-21-11 report, CCT 5700K / 6000K / 6500K (ANSI bin), SDCM <5, and maximum power consumption not exceeding rated wattage. The fixture shall conform to relevant BIS standard and shall include all accessories, fixing arrangements, internal wiring with suitable size FRLS PVC insulated copper conductor cable, connections and earthing, complete in all respects, with minimum 5-year OEM warranty. LM-79 and LM-80 test reports from NABL-accredited laboratory, as required under BIS for LED luminaires shall be submitted complete all as specified and directed.
141S&F LED surface-mounted batten light fitting, 20 Watt, with powder-coated die-cast/extruded aluminium or CRCA sheet phosphated and powder coated body, construction conforming to IS:10322 (Part-1) / IEC 60598-1 with replaceable high-efficiency electronic driver (driver efficiency ≥85%), system lumen efficacy ≥120 lm/W, suitable for AC 140–270 Volts, 50 Hz, operating temperature –15°C to +40°C. The luminaire shall be provided with internal surge protection minimum 2.5 kV, short-circuit and open-circuit protection, THD <10%, power factor ≥0.95, IP-20 protection, CRI >80, and flicker ≤5%. The LED shall have a minimum rated life of 50000 burning hours with 70% lumen maintenance at end of life. The CCT shall be 5700K / 6000K / 6500K (ANSI bin) with SDCM <3, and maximum power consumption shall not exceed the rated wattage. The luminaire shall conform to relevant BIS standards and bear a valid BIS Trade Mark Certificate (TC). Manufacturer’s name/word mark shall be engraved / embossed / screen-printed on the housing. The item includes internal wiring with suitable size FRLS PVC insulated copper conductor cable, all connections, earthing, fixing accessories, and is complete in all respects with minimum 5-year OEM warranty. LM-79 and LM-80 test reports from a NABL-accredited laboratory, as mandated under BIS for LED luminaires shall be submitted complete all as specified and directed.
142S&F LED surface-mounted batten light fitting, 9/10 Watt with powder-coated die-cast/extruded aluminium or CRCA sheet phosphated and powder coated body, construction conforming to IS:10322 (Part-1) / IEC 60598-1 complete with high-efficiency electronic driver (driver efficiency >85%), system lumen efficacy ≥120 lm/W, suitable for AC 140–270 Volts, 50 Hz, and operating temperature –15°C to +40°C. The luminaire shall be provided with internal surge protection minimum 2.5 kV, short-circuit and open-circuit protection, THD <10%, power factor ≥0.95, IP-20 protection, CRI >80, and flicker-free operation (flicker ≤5%). The LED shall have a minimum rated life of 50000 burning hours with 70% lumen maintenance at end of life. The CCT shall be 5700K / 6000K / 6500K (ANSI bin) with SDCM <3, and maximum power consumption shall not exceed the rated wattage. The luminaire shall conform to relevant BIS standards and bear a valid BIS Trade Mark Certificate (TC). Manufacturer’s name/word mark shall be engraved / embossed / screen-printed on the housing. The item includes internal wiring with suitable size FRLS PVC insulated copper conductor cables, all connections, earthing, fixing accessories, and is complete in all respects with minimum 5-year OEM warranty. LM-79 and LM-80 test reports from a NABL-accredited laboratory, as mandated under BIS for LED luminaires shall be submitted.
143S&F of surface-mounted LED bulkhead luminaire 10 W with pressure die-cast aluminium housing finished with polyester powder coating, opal polycarbonate diffuser, minimum system efficacy ≥100 lm/W, integral electronic driver with PF ≥0.9 and THD ≤10%, CCT 6500 K, CRI ≥80, minimum Ingress Protection IP65, minimum Impact Resistance IK08, rated life ≥50000 hours @ L70, suitable for operation on 160–270 V AC, 50 Hz complete with 0.75 sqmm factory pre-wired PVC sheathed, three-core flexible multi-stranded copper conductor cable connection including all fixing arrangements and minimum 5-year OEM warranty. LM-79 (luminaire) and LM-80 (LED source) test reports from NABL-accredited lab as mandated under BIS for LED luminaires shall be submitted.
144M&L for earthing with galvanised steel earth plate electrode of size 600 mm × 600 mm × 6 mm thick, buried directly in ground with earth pit not less than 2.25 metres deep below normal ground level, with top edge of earth plate not less than 1.5 metres below normal ground level, connected to galvanised steel earth lead wire 4 mm dia by means of galvanised steel bolts, nuts, check nuts and washers, all as shown on Electrical Plate No. 3 of MES SSR Part-I (2009), including 15 mm bore light grade GI protection pipe for earth lead up to 7.5 metres beyond the outer edge of earth pit, PCC chamber in cement concrete 1:3:6 type C-1, with RCC cover slab in cement concrete 1:2:4 type B-1, 40 mm thick, reinforced with 6 mm dia MS bars, 3 Nos each way, provided with lifting handle made out of 6 mm dia MS bar, watering arrangement consisting of funnel with wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling including necessary excavation, earth work, and testing on completion complete.
145Taking out old serviceable ceiling fan and wall mounting fan and refixing the same after carried out necessary painting winding , oiling and replacement of ball bearings and make functional complete all as directed
146S&F of exhaust fan single phase, 230/240 Volt heavy duty of size 300 mm sweep 1400 RPM including suitable louvers and making connection with twisted copper flexible wire 23/0.076mm all as specified and directed.
147S & F Exhaust fan 300 mm , 230 Volt heavy duty , single phase with louvers connection up incl suitable size three core flexiable copper cable from ceiling rose complete all as directed
148S&F in repair Stepped type electronic fan regulator 2 module modular type complete
149Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one MCB single pole 20 Amp complete
150S&F in repair of MCB vertical distribution board, triple pole and neutral (TPN), 4-way, 415 Volts, factory-assembled type, conforming to IS/IEC 61439 (Low-voltage switchgear and controlgear assemblies), fabricated from powder-coated CRCA steel sheet enclosure, recess-mounted, suitable for MCCB incomer up to 160 Amp having a minimum degree of protection IP-43 and mechanical impact resistance IK-09 with reversible double door, incorporating insulated tinned copper busbar of 250 Amp rating, separate neutral busbar and earth busbar, DIN rail, and detachable gland plate, including all internal interconnections, earthing connections, and blanking plates for all unused ways/spaces complete.
151Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete all as specified and directed.
152Excavation in trenches soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of pipes/cables etc getting out and bottom surface to required gradient complete all as directed & specified
153M & L Returning filling in including spreading leveling watering and well ramming in layers each not exceeding 25 cm thickness complete all as specified and as directed
154M & L Removal of surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed
155Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable complete all as specified & directed. i.e 18 cm punned down thick shall be considerd for mesurement)
156M & L Old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable , adjacent/abutting each other complete all as specified Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58553394
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 38.82 Lakhs
LAST DATE 07-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for special Repair To Bldg No P-98 (Or Govt Md Accn) At Sanjay Vihar (Hudson Lines) Of Afmsd Lucknow Under Ge (East) Lucknow
Basic Detail
Tender No GE/E/LKO/T-114 OF 2026-27
Bidding Type Tender
Location
City Lucknow
State Uttar Pradesh
Key Dates
Publish Date 16 Nov 2026
Submission Date 07 Dec 2026
Open Date 10 Dec 2026
Finance
Tender Value 38.82 Lakhs
Tender Fee 500
EMD 77640
Exemption Available
Document List
9414005f-f4fc-434e-8647-cbccb1359324.html
BOQ_896385.xls
Tendernotice_1.pdf
TenderT114.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 16, 2026
11:30 IST

Tender Published

Tender notice published.

Today
Dec 07, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 21 days
Dec 10, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 24 days

Tender Documents

Download All (ZIP) ↓
html

9414005f-f4fc-434e-8647-cbccb1359324.html

xls

BOQ_896385.xls

pdf

Tendernotice_1.pdf

pdf

TenderT114.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender