Housing Urban and Rular Development Government Departments Closing in 11 days TDR #58550450

Tender For Development Of Tourist Points At Galigad Sarthal Kishtwar

Issued by Government Departments · Kishtwar, Jammu and Kashmir
Tender Value
1.34 Crore
Estimated cost
Bid Submission
01 Dec 2026
11 days left
EMD
2.68 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Kishtwar → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Development Of Tourist Points At Galigad Sarthal Kishtwar

BOQ

Name of Work:- Development of Tourist Points at Galigad Sarthal Kishtwar
Sl. No. Item Description
1Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil :
2All kinds of soil
3ORDINARY ROCK
4HARD ROCK (BLASTING PROHIBITED)
5Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed in All kinds of soil :
6Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sidesand ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil
7Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
8Random rubble stone masonry with hard stones in foundation and plinth including levelling up with cement concrete 1:6:12 (1 Cement :6 Coarse sand :12 graded stone aggregates 20 mm nominal size ) upto plinth and curing complete with :Cement mortar 1:6
9Dry random rubble masonry with hard stone in foundation and plinth: Without bond stone.
10Dry random rubble masonry with hard stone in foundation and plinth: Without bond stone. Using available stone from cutting
11Providing and laying P.C.C in M 10 GRADE 1:3:6 (1cement:3 coarse sand: 6 graded stone aggregate 20 mm nominal size) and curing complete
12Providing and laying in position cement concrete of specified M 15 grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
13Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level M 20 GRADE 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size ) All works upto plinth level
14Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size ) All works above plinth level upto floor V level
15Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
16Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all levels:- Thermo-Mechanically Treated bars of grade Fe-500D or more.
17FORM WORK:- Centering and shuttering including strutting, propping etc. and removal of form for:
18Centering and shuttering including strutting, propping, etc and removal of form work for foundations , footings ,bases of columns etc.
19Centering and shuttering including strutting, propping, etc. and removal of form work for Wall any thickness including attached pillasters, buttresses , plinth and string courses etc.
20Centering and shuttering including strutting, propping, etc. and removal of form work for columns ,pillars ,piers etc.
21Centering and shuttering including strutting, propping, etc and removal of form work for lintels, beams , girders , bressumers and cantilevers all complete.
22Centering and shuttering including strutting, propping, etc. and removal of form for Suspended floors, roofs, landings, balconies and access platforms.
23Centering and shuttering including strutting, propping, etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide
24Providing and laying in position Damp Proof Course 50 mm thick with cement concrete of specified grade 1 : 2 : 4 (1 cement: 2 coarse sand: 4 graded stone agg. 20 mm nominal size) crushed and curing complete.
25Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.
26Filling available excavated earth (excluding rock ) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolifating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m
27Disposal of excavated earth by way of mechanical transport upto lead 2.0 Km and 50m head load
28Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand). Above Plinth Level
29Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level
30Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)
31Extra for half Brick masonry in superstrcture above plinth level upto floor level
32Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing. One face dressed Fine chisel dressed
33Extra for fine chisel dressed Devri Stone in square or rectangular Pillars
3412 mm Cement plaster on the rough side of single or half brick walls of mix 1: 6 ( 1 cement : 6 fine sand ) on interior walls all complete including making of groves and scaffolding etc. at all floor levels complete. ( including cost / carriage of material by Mechanical transport)
3515 mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) ,in two coats on exterior walls, all complete including making of groves, drip course and scaffolding etc., all floor levels complete (Including cost / Carriage of material by Mechanical transport)
36Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size of tile 60x60cm.
3715 mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) ,in two coats on exterior walls, all complete including making of groves, drip course and scaffolding etc., all floor levels complete (Including cost / Carriage of material by Mechanical transport)
38Providing, engraving, and fixing highly polished Jet Black Granite stone plaque (18 mm to 20 mm thick) for inauguration/foundation stone. Item includes V-groove machine/hand carving of lettering, gilding/filling letters with exterior-grade oil-bound/gold enamel paint, chamfering edges, joint mortar/adhesive, fixing onto masonry/concrete wall, cleaning, and finishing complete in all respects as per direction of Engineer-in-Charge (LMR)
39Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite Work
40Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of size 300x450mm as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
41Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design, fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:
42Providing and applying white cement based putty of average thickness 2 mm of approved brand and manufacture over the plastered wall surface to prepare the surface even and smooth complete inclulding cost of material and carriage complete.
43Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.
44Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and Colour. 13.90.2 Two coats
45Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm
46Extra for providing opening of required size and shape for wash basin/ kitchen sink in kitchen platform, vanity counters and similar location in marble/granite / stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
47Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Riveted and bolted
48Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.
49Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
50Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 12.24.1 Ridges plain (500 - 600mm)
51Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
52Providing and fixing mineral fibre false ceiling tiles at all heights ofsize 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking TGrid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all Tsections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge With 16 mm thick bevelled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6
53Steel work welded in built up sections/framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
54Making plinth protection 50 mm thick of cement concrete 1: 3 :6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. (a) Crusher (Including cost / carriage of Mechanical transport)
55PROVIDING WOOD WORK IN FRAMES OF DOORS, WINDOWS AND OTHER FRAMES, WROUGHT FRAMED AND FIXED IN POSITION WITH HOLD FAST LUGS OR DASH FASTENERS OF REQUIRED DIA AND LENGTH ( HOLD FAST LUGS OR DASH FASTENERS SHALL BE PAID SEPARATELY ) SAL WOOD
56Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).Including all cost of material and carriages complete.
57Providing and fixing ISI marked flush door shutters 35 MM TH conforming to is 2202 part 1 deccorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both sides of shutters with ISO marked M S Pressed butt hinges bright finished of required size with necessary screws
58Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge using 30 mm Thick Second Class Deodar Wood
59Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws 30 mm Thick Second Class Deodar Wood.
60Providing and fixing bright finished brass hard drawn hooks and eyes 150 mm
61Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc. Inc. all costs of materials and carriage complete.
62Providing and fixing glazing in door, window, ventilator shutters and partitions complete as per the architectural drawings and the directions of engineer-in-charge.With floating glass panes of 8.0 mm thickness (weight not less than 20.00 kg / sqm)
63Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)
64Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. 13.0 (Finishing) 13.70.2 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
65Providing and fixing aluminium ISI MARKED BUTT HINGES anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :
66Providing and fixing aluminium sliding door bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :
67Providing and fixing aluminium tower bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :
68200x10mm
69150x10mm
70Providing and fixing aluminium handles lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.
71300 mm long
72125 mm long
73Providing and fixing aluminium hanging floor door stopper lSI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper
74Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete :
75Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti termite treatment. (excluding the cost of chemical emulsion): Along the external wall below concrete or masonry apron using chemical emulsion (Chloropyriphos / Lindane E.C. 20% with 1% concentration) @ 2.25 litres/ linear meter including drilling & plugging holes etc.
76Preparation of subgrade by excavating earth to an average of 22.5 cm depth, dressing to camber and consolidation with road roller of 8-12 tonne capacity including making good the undulation etc. and disposal of surplus earth upto 50 meters.
77Supply and filling of Nallah Muck or second class quarry stones as filter media behind abuts etc including proper consolidation and all other carriage complete
78Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.
79Chequerred terrazzo tiles 22mm thick with graded marble chips of size upto 6mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, polishing and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Dark shade using ordinary cement.
80Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied W.C. pan with lSI marked white solid plastic seat and lid
81Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.
82Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:Range of two urinal basins with 5 liter white P.V.C automatic flushing cistern
83Providing and fixing wash basin with C. I./M.S. brackets,15mm C.P. centre hole basin mixture, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China round wash basin size 405x355 mm with a pair of 15 mm C.P. brass pillar taps
84Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
85Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour:Waste coupling 38mm of 83 mm length and 77 mm breadth weighing not less than 60gms.
86Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610 x 510 mm bowl depth 200mm
87Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete. Flexible pipe 40 mm dia
88Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour:Waste coupling 38mm of 83 mm length and 77 mm breadth weighing not less than 60gms.
89Providing and fixing unplasticised - Rigid PVC PIPES conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap of thermal expansion;with necessary stays / clamps with fasteners having working pressure of 4kg/cm2 all complete including testing of joints and pipes for leakage etc.:-
9075 mm dia
91110 mm dia
92Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2:- all complete including testing of joints and pipes for leakage etc.:-
93PVC PLAIN BEND (of required degree):-
9475 mm dia.
95110 mm dia
96PVC DOOR BEND( of required degree):-
9775 mm dia.
98110 mm dia
99PVC PLAIN TEE
10075 mm dia.
101110 mm dia
102PVC REDUCER PLAIN TEE:-
103110 mm x 75 mm
104PVC OFFSET
10575 mm dia.
106110 mm dia
107PVC COUPLER /COLLAR
10875 mm dia.
109110 mm dia
110PVC VENT COWL:-
111110mm dia
112PVC FLOOR /NAHANI TRAP:-
113110 mm x 75 mm
114110 mm x 100 mm
115Providing and fixing (C.P. Brass ) towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms.
116Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete ISI marked as approved by Engineer incharge at site
117Providing and fixing 100 mm CP grating (hole or without hole) for gully, floor or Nahani trap.ISI marked all complete .
118Providing and fixing Soap dish (C.P. brass) with brackets ,nuts & screws complete etc.
119Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia
120Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms a) 15 mm nominal bore
121Providing and fixing C.P. brass stop cock ( concealed) of standard design and of approved make concorming to IS : 8931 a) 15 mm nominal bore
122Providing and fixing C.P. brass angle valve for basin/ wall mixer and geysers points of approved make conforming to IS : 8931 15 mm nominal bore as approved by site incharge
123Providing and fixing G.l. pipes complete with G.l. fittings and h0oks, including cutting and making good the walls etc.(internal work) as approved by site incharge -Exposed on wall) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.
12415 mm dia. nominal bore (medium)
12525 mm dia. nominal bore (medium)
126Making connection of G.l. distribution branch with G.l. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete all complete including testing of pipes and fittings and joints for leakage with pressure pump etc. as approved by site incharge
12725 to 40 mm nominal bore
128Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.as approved by site incharge
12925 mm nominal bore
130Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank
131Providing and fixing G.I.TANK NIPPLE of suitable dia. as approved by engineer incharge at site all complete including testing of fittings and joints for leakage etc.:-
13232 mm dia. nominal bore
133Providing & fixing BRASS BALL VALVE of approved quality conforming to IS : 8931 as approved by site incharge
13425 mm nominal bore
13540 mm nominal bore
136Providing & Installation of 1.5 H.P. three phase water pump of make Crompton with all fittings, connecting inlet & outlet, fixtures, electrical connection and starter all complete:-
137Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design
138Inside size 90x80 cm and 45 cm deep including C.l. cover with frame (light duty) 455x610 mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg):- With F.P.S. bricks with class designation 75 & with Crushed stone aggregate
139Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design by way of earth excavation by mechanical means; laying of 100 mm thick P.C.C. bed in 1:4:8 mix ratio & R.C.C. Slab on top in 1:1.5:3 mix ratio; providing and fixing of Manhole with MS frame and cover having passing of 50 mm dia. Vent air pipe through it for foul gases; brick masonry in 1:6 cement mortar mix with providing of pores; and filling of brick bat aggregates around the dry brick honey comb shaft; P/F of pvc bend/tee at the S.W. Drain pipe; all complete etc:- With F.P.S. bricks and Crushed
140Supply & fixing CI cover with frame for manhole in sump / septic Tank 455 x 610 mm rectangular CI cover ( light duty ) the weight of the cover to be not less than 23 kg
141Providing & fixing 100 mm dia PVC Pipes for weep holes in cement concrete wall / return wall of make PRINCE or equivalent, extending through the full width of the structure at mid height of wall and @ 1 metre spacing with slope of 1 V : 20 H as per direction of engineers in charge incuding all carraiges.
142Dumping of stones filling behind R / Wall including supply of stones in horizontal on level
143Hand Packing of Stones in wire crates including cost of stones and wire crates .
144Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing off by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure)
145Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. 2.27.2 Beyond 60 cm girth upto and including 120 cm girth.
146Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment)
147Supplying and stacking at site dump manure from approved source including carriage complete (manure measured in stacks will be reduced by 8% for payment) 17.4.1 Screened through sieve of I.S. designation 20 mm
148Spreading of sludge, dump manure or/and good earth in required thickness as per directions of officer in-charge (cost of sludge, dump manure or/and good earth to be paid separately)
149Grassing with selection no. 1 grass including watering & maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds & fit for mowing including supplying of good earth if needed (the good earth shall be paid separately.) In rows 5 cm apart in either direction
150Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds & fit for mowing & disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (the good earth shall be paid separately.)
151Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts
152Flooding the ground with water including making kiaries and dismantling the same
153Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 part of stacked volume of earth after reduction by 20% :1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish & surplus earth, if any with all leads & lifts (cost of sludge, manure or extra good earth, if needed, to be paid for separately)
154Holes 45 cm dia & 45 cm deep
155Holes 60 cm dia & 60 cm deep
156Providing and fixing M.S tree guard 45 cm square in plan, height 1.20 meter above ground level and 0.40 meter below ground level. The vertical members shall consist of four nos. angle iron of size 25x25x3 mm, 1.6 m long, one at each corner and 8 nos flat iron of size 25x3 mm, 1.2 m long. The vertical members shall be welded to 4 nos. 25x6 mm M.S flats placed horizontally around the vertical members of the cage. One name plate of 1 mm thick M.S sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD /PWD/any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two more coats of synthetic enamel paint of approved brand and or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer complete
157Supplying and planting of one-year-old Duranta erecta saplings in polybags, including carriage, handling, and all leads and lifts; preparation of hedge bed with removal of weeds and debris; planting of saplings at 0.4 m centre-to-centre spacing in single row over a hedge width of 0.5 m; providing and applying compost or soil amendment around each plant; providing stakes and tying for support; application of organic mulch (0.5 m wide) along hedge bed; all labour for digging, planting, watering, and initial shaping; and first-year maintenance including manual irrigation, watering, weeding, and pruning for two visits complete as per direction of Engineer-in-Charge and standard horticultural practice. (Payment shall be made only after the hedge has attained a uniform height of not less than 45 cm and width of about 30–45 cm, with a minimum of 90% survival of plants, after satisfactory maintenance for at least six months from planting.
158Providing, installation, testing and commissioning of Solar Street Light complete system with Pole (G.I/painted) 5.0 or 6.0 m height MS tubular / GI pole, single-arm type; with 200 × 200 × 12 mm base plate and 4 Nos. M20 × 600 mm galvanised anchor bolts. Pole hot-dip galvanised or painted (2 coats enamel paint over zinc primer). Luminaire (LED) 30 W and above, IP65 weatherproof, die-cast aluminium housing, inbuilt driver and automatic dusk-to-dawn operation. Power factor ≥ 0.95, luminous efficacy ≥ 120 lm/W, 5700 K colour temperature of approved Brand and manufacture. Solar PV Panel: 100 W - 150 W, mono/polycrystalline silicon, 18% minimum efficiency, with anodised aluminium frame and toughened glass. Mounted on adjustable MS bracket at 15°–30° tilt facing south. Complying with IS 14286 / IEC 61215.Battery 12.8 V / 100 Ah LiFePO₄ (Lithium Iron Phosphate), maintenance-free, with inbuilt BMS protection against overcharge, over-discharge, short-circuit & reverse polarity. Autonomy minimum 2 days. Weatherproof IP65 housing, mounted on pole. Charge Controller MPPT / PWM type, efficiency ≥ 95%, with load & battery protection, integrated within the luminaire. Foundation RCC M20 (1:1.5:3) foundation block 0.45 m × 0..45 m × 0.80 m, including excavation, 100 mm PCC (1:4:8) bedding, reinforcement (8 mm Ø @150 mm c/c both ways), anchor bolts, shuttering, backfilling & curing. Top surface finished smooth and at least 100 mm above ground. Earthing GI pipe electrode (40 mm Ø × 2.5 m long) with 8 SWG GI wire connection to pole. Earth resistance ≤ 5 ohms. Wiring & Accessories ISI-marked copper flexible wires, junction box (IP 65), cable lugs, ferrules, clamps, UV-resistant ties, and accessories. All wiring concealed / clamped neatly on pole. Installation & Testing Transporting all materials from approved source (e.g. Jammu) to site, unloading, erection of pole, fixing of PV panel, LED fitting, battery, and connections. Testing for illumination, battery charge/discharge, and automatic dusk–dawn operation.
159Supply, transportation, installing,testing and commisioning of 5.0 m high heritage-style Decorative street light pole, fabricated from hot dipped galvanized steel ( min80 microns) with decorative cast base and custom fabricated ring at top for catenary wire support, complete Heavy duty waterproof , insect proof IP65 rated LED Haritage lantern equiped with high efficiecy 45 watt , internal wiring using 3 armored cable,ug feeder cables mCB protection and Terminal blocks. The Pole should be laid in RCC m20 grade concrete foundation base (min 450x450x750mm) all as per directions of engineer in Charge (LMR)
160Supply Transportation and installation ornamental garden/park bench (3-seater type) made o decorative cast iron/mild steel frame with armrests and legs, fitted with seasoned hardwood/FRP Slats (25-32mm thick) for seating and backrest, finished with two coats of weatherproof paint/polish over anti-rusting primer, including all stainless-steel fasteners, fixing in position by gruting legs in cement concrete Block (1:2:4) mix of size 200x20x300 nnm complete in all respects including labour, material transport and taxes
161Design, fabrication, supply and installation of an illuminated Selfie Point measured and paid per sqm, fabricated with a sturdy MS square/rectangular pipe framework and finished with 12 mm MDF/HDHMR or equivalent board, including high-quality vinyl printing/lamination, acrylic/foam board 3D lettering and decorative elements as per approved design. The selfie point shall be provided with concealed LED strip/profile lighting and LED backlit/acrylic lettering, complete with suitable wiring, power supply, switches and necessary electrical accessories, along with surface finishing, supports, fixtures, transportation and on-site installation, complete in all respects and ready for use.
162Providing and fixing stainless steel twin dustbin with sturdy stand for segregation of wet and dry waste, consisting of two cylindrical/swing-type stainless steel bins of 60 litres capacity each (total capacity 120 litres), fabricated from good quality SS-202 grade stainless steel sheet with smooth/mirror finish, complete with suitable lids/swing arrangement, sturdy MS/SS supporting frame or stand, necessary brackets, clamps, welding, fasteners, anti-rust treatment, waste identification stickers/labels, provision for anchoring/fixing the stand to the floor, and all necessary materials, labour, loading, unloading, transportation and installation, complete in all respects as directed by the Engineer-in-Charge.
163Providing, supplying, installing, testing and commissioning of a complete RGB Dandelion cum Vertical Jet Water Fountain for outdoor park application, comprising suitable fountain nozzles of SS-304/brass, complete with high-efficiency submersible pump(s), suction/discharge piping, valves, fittings, strainers, isolation valves, underwater RGB LED lights, suitable SMPS/driver, programmable control panel with timer and colour-changing controller, electrical cables and all necessary accessories. The fountain shall provide a dandelion/radial spray effect with a central vertical jet, with adjustable jet height and spray pattern. The complete system shall be suitable for continuous outdoor operation and recirculating water from the fountain basin, including testing and commissioning, complete as directed by the Engineer-in-Charge.
164Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab upto 0.5 sqm)
165Carriage of Material
166Sand up to lead 38 Km MT & 50m HL
167Aggregate Below 40 mm up to lead 29 Km MT & 50m HL
168Bricks up to lead 218 Km MT & 50m HL
169Tiles up to lead 29 Km MT & 50m HL
170Earth UPTO 02 KM BY MT
171Carriage of Stone at an avg. distance of 24.0 Kms By MT & 50m HL Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58550450
AUTHORITY Government Departments
TENDER VALUE 1.34 Crore
LAST DATE 01-12-2026
Authority
Authority Name Public Works Department
Work Description Tender for Development Of Tourist Points At Galigad Sarthal Kishtwar
Basic Detail
Tender No e-NIT No. 74 of 2026-27 Dated 16-11-2026
Bidding Type Tender
Location
City Kishtwar
State Jammu and Kashmir
Key Dates
Publish Date 16 Nov 2026
Submission Date 01 Dec 2026
Open Date 02 Dec 2026
Finance
Tender Value 1.34 Crore
Tender Fee 3000
EMD 2.68 Lakhs
Exemption Not Available
Document List
0bad56f0-c939-4b93-9eb0-51fda3e3c437.html
BOQ_1124431.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 16, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 01, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 11 days
Dec 02, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 12 days

Tender Documents

Download All (ZIP) ↓
html

0bad56f0-c939-4b93-9eb0-51fda3e3c437.html

xls

BOQ_1124431.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender