Tender For special Repair To Bldg No P-6, T-53, T-53B, T-53C And T-53D Of 2Ttr , special Repair To Compound Wall Of Dsoi & Swimming Pool And special Repair To Bldg No-344 Md Accn At Cobra Ground Ridge Road Under Ge (P) No.1 Jabalpur
Tender Overview
Project Description
Tender for special Repair To Bldg No P-6, T-53, T-53B, T-53C And T-53D Of 2Ttr , special Repair To Compound Wall Of Dsoi & Swimming Pool And special Repair To Bldg No-344 Md Accn At Cobra Ground Ridge Road Under Ge (P) No.1 Jabalpur
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling Plain or corrugated steel/AC/fiber sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 2 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 3 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 4 | Taking down Cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. |
| 5 | Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles and removing debris and depositing complete all as specified and as directed. |
| 6 | Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 7 | Dismantling timber scantlings 40 sq. cm and over in section, in any position in unframed/framed work complete all as specified and directed |
| 8 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft/loose soil complete all as specified and directed. |
| 9 | Taking down chowkats or frames including shutter (without taking off shutters from the frame) area n exc. 1.5 Sqm each. complete all as specified and directed. |
| 10 | ~ditto~ all as per item No 9 above but exc 1.50 Sqm n.exc 4 Sqm. complete all as specified and directed. |
| 11 | M&L for brick work with Sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortor 1:4.complete all as specified and directed. |
| 12 | M&L for brick work with sub class 'B' bricks using old size bricks, straight or curved on plan to any radius, built in CM 1:4 as in half brick thick wall complete all as specified and directed. |
| 13 | M&L for Cement concrete type D-2, 1:4:8 (using 40 mm graded aggregate) as in foundation filling and mass concrete complete all as specified and directed. |
| 14 | M&L for Providing, cement concrete type B0 1:2:4 (12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, coping Hold fast complete all as specified and directed. |
| 15 | M&L for Granite slab 16 mm to 18 mm thick machine cut, bedded and joined with cement and pointed with white cement with admixture of pigment to match over and including 20 mm thick screed bed CM (1:4) .the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges and polishing complete all as specified and directed. |
| 16 | M&L for Machine cut cudappah stone slab 20-25mm thick horizontal/ vertical partion over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 17 | M & L for Vitrified Ceramic tiles (double charged) 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm, but n exc 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchand over and including 20 mm thick screed bed in CM 1:4 to recieve tiles complete all as specified and directed. |
| 18 | M & L for Vitrified Ceramic tiles (double charged)10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm, but n exc 1.00Sqm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchand over and including 10mm thick backing coat in CM 1:4 to recieve tiles complete all as specified and directed. |
| 19 | S&F Coloured Non Skid coloured ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick screed in CM(1:6) complete all as specified and directed. |
| 20 | S&F Coloured Glazed ceramic tiles in vertical surfaces 350x250mmx7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including15mm thick backing coat in CM(1:4) on fair face of brick or concrete surface complete all as specified and directed. |
| 21 | S&F 10 mm thick paver tiles out door vitrified tiles area n. exc 0.36 sqm each as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed in CM(1:6) complete all as specified and directed. |
| 22 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (with incl two nos. glazed , 4mm glass plain & one no. wire mesh panels of 0.36mm dia wire and 1.40mm aperture) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge.Note: For uPVC frame and sash extruded profilesminus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and directed. |
| 23 | S&F Factory made single/double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm(double rebat) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length including fastenar of 100 mm long 10 mm dia complete all as specified and directed. |
| 24 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length including fastenar of 100 mm long 10 mm dia complete all as specified and directed. |
| 25 | S&F in repairs, Factory made single/double extruded WPC (Wood Polymer Composite) solid decorative prelam both side flush door 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture pr oof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified and directed. |
| 26 | S&F wire gauge i.e. panel will be wire gauge in liew of double side prelam PVC sheet panel the wire gauge shell be wrapped on a additional square 8 mm solid tube and the tube shell be welded tomMS tube the wire gauge shell be stretched to tighten firmly Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed. |
| 27 | M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 28 | S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 29 | S&F SS butt hinges100mm long medium weight, cold rolled. complete all as specified and directed. |
| 30 | S&F 200 mm long extruded SS handles, fabricated type. complete all as specified and directed. |
| 31 | S&F 150 mm long extruded alu alloy handles, fabricated type, anodised. complete all as specified and directed. |
| 32 | S&F 300mm SS sliding door bolt with hasp, staple bolt type and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy. complete all as specified and directed. |
| 33 | S&F 200mm long SS barrel tower bolts of extruded section and fixed. complete all as specified and directed. |
| 34 | S&F 150mm long Aluminium,anodized barrel tower bolts of extruded section and fixed. complete all as specified and directed. |
| 35 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples. complete all as specified and directed. |
| 36 | S&F Aluminium louvers with levers and locking arrangement suitable for fixing 100mm wide 4 to 6 nos glass incl 5mm thick frosted glass complete all as specified and directed. |
| 37 | S&F 4.00 mm thick sheet glass ordinary/tinted quality and glazing complete in square nexc 0.50sqm each. complete all as specified and directed. |
| 38 | M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters/frame of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings complete all as specified and directed. |
| 39 | S&F Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. complete all as specified and directed. |
| 40 | M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 41 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) including distance pieces, cleats etc complete all as specified and directed. |
| 42 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 43 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 44 | M&L for suspended false ceiling system using chicago metallic (E grid) exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24 mm X 0.8 mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2 mm X 22.2 mm X 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) with Provn of light fixture complete all as specified and directed. |
| 45 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 46 | Excavation in trenches n exc 1.5m wide n exc 1.5m deep in soft/loose soil complete all as specified and directed. |
| 47 | Returning filling in incl spreading levelling watering and well rammmed in layers n exc 25cm complete all as specified and directed. |
| 48 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.50m for soil complete all as specified and directed. |
| 49 | M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes for 150 mm bore SWG pipes including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed. |
| 50 | Supplying, laying and jointing for 150-160mm nominal dia DWC pipes class SN-4 conforing to IS -16098:2013 Part-I stiffness with and incl necessary jointing materials complete all as specified and directed. |
| 51 | S&F in repairs cascade duel flush one peace inbuilt flushing cistern vitreous china wash down water closet pan padestel pattern white including soft seat cover, connection pipe to union of flushing cistern, inlet and overflow pipes,connecting anti-syphonage pipe with PVC flush pipe of 32mm dia with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed. |
| 52 | S&F Vitreous China wash down water closet pan (pedestal pattern), white, connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia with mild steel chromoum plated complete all as specified and directed. |
| 53 | S&F in repair 10 litre capacity PVC flushing tank,, syphonic action type, flushing cistern, low level, white, with inlet, ball valve,pvc flush pipe, float and handle incl brackets and waste pipe complete all as specified and directed. |
| 54 | S&F in repair brass chromium plated overhead shower 125mm size (squar/rectangular) with or without swivel joints including fixing to steel pipe of 15mm bore complete all as specified and directed. |
| 55 | S&F in repair ovel type counter top/ flat back Wash hand basin 550x400mm vitreous china (white) including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore,complete all as specified and directed. |
| 56 | S&F in repair 15mm bib taps, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. (Make/ sample approved by GE) Jaquar (FLR-5047N) or equivalent of Kohler, Roca |
| 57 | S&F in repairs 15mm angle cock/stop cock chromium plated,cast copper alloy, and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified and directed.(Make/ sample approved by GE) Jaquar (FLR-5047N) or equivalent of Kohler, Roca |
| 58 | S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 59 | S&F in repair Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed. (Make/ sample approved by GE) Jaquar (FLR-5273UPR) or equivalent of Kohler, Roca |
| 60 | S&F in repair Brass Chromium plated sink/basin mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed.(Make/ sample approved by GE) Jaquar (FLR-5025B) or equivalent of Kohler, Roca |
| 61 | S&F in repair 15mm bore GI Tubes, 'medium grade',galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 62 | S&F in repair 20mm bore GI Tubes, 'medium grade',galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 63 | S&F in repair 25mm bore GI Tubes, 'medium grade',galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 64 | S&F in repair 25mm PVC valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brassv ferrule and fixed complete all as specified and directed. |
| 65 | S&F in repair Gun-metal,25mm globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 66 | S&F in repair Gun-metal, 20mm globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 67 | S&F in repair Health faucet (ABSBody) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.(Jaquar ALD-565 or equivalent of Kohler, Roca) |
| 68 | S&F Chromium plated SS toilet paper holder including fixing arrangement complete all as specified and directed. |
| 69 | S&F Chromium plated SS soap dish including fixing arrangement complete all as specified and directed. |
| 70 | M&L for repairs PVC Nahani trap long neck 100 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1, 1:2:4 complete all as specified and directed. |
| 71 | M&L for repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 72 | S&F in repair bevelled edge mirror of selected quality 5mm glass, mounted on 5mm thick PVC fibre board and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 73 | S&F 150mm size (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 74 | M&L for 300mm, ordinary rat tail rod/capsule rod pattern springs made of brass including roller and roller plate complete all as specified and directed. |
| 75 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store complete all as specified and directed. |
| 76 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in fixed to walls complete all as specified and directed. |
| 77 | S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 78 | S&F 110mm bore PVC (SWR) junction single, (single T) equal or unequal any radius complete all as specified and directed. |
| 79 | S&F 110mm bore PVC (SWR) cowl any radius complete all as specified and directed. |
| 80 | S&F PVC (SWR) pipe inner dia 75mm single socketed in any length with rubber ring joint laid on wall/ceiling or laying in floors complete all as specified and as directed |
| 81 | S&F for 75 mm dia PVC (SWR ) bends and radius complete all as specified. |
| 82 | S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal with or without access door complete all as specified and directed |
| 83 | M&L for preparation of new surfaces of steel or iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 84 | M&L for preparation of old surfaces of steel or iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 85 | Providing and fixing factory made cupboard shutter with 18 mm thick one side decorative and other side balancing lamination factory pressed OSL HDHMR board of Action Tesa and Equivalent including 2 mm thick PVC edge banding type with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraullic type) etc, complete made by action Tesa authorised OEM complete all as specified and directed. |
| 86 | Providing and fixing factory made with 18mm thick both side balancing lamination factory made HDHMR wood of action Tesa and equivalent approved brand for boxes, shelves, racks, almirah, cupboard and drawer etc including necessary nails, screws etc, complete made by action tesa authorised OEM complete all as specified and directed. |
| 87 | Providing and fixing factory made modular wardrobe with 8 mm thick both sides pre-laminated BSB (both side balancing paper) HDHMR of action tesa and equivalent as per IS: 14587 - 1998 with suitable full threaded steel screws etc on the backing of racks drawer, cupboard, kitchen, cabinet under kitchen counter etc, all complete make by action tesa authorised OEM complete all as specified and directed. |
| 88 | S&F 30mm width Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 89 | M&L for 15 mm thick cement plaster in CM 1:6 on internal surfaces of fair faces of brick work or concrete surfaces with finished surfaces even and smooth with out using extra cement all as specified and directed. |
| 90 | M&L for 75mm thick PCC (1:3:6) Type C2 using 40mm graded stone agg as in plinth protection surface even and fair without using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and diected |
| 91 | M&L for Distempering with 1st quality acrylic distemper (ready mixed) washable, antifungal having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work/old surfaces of wall/ceilingas per manufacturer instructions applied over priming coat with fully automatic airless spary machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI and allow 6-8 hrs to dry the surfaces in both the coats of paint, complete all as specified and directed. |
| 92 | Material & Labour for applying Two or more coats of 100% on new/ old surfaces of wall/fascia etc Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces as per manufacturer instructions applied over priming coat with fully automatic airless spary machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI and allow 6-8 hrs to dry the surfaces in both the coats of paint, complete all as specified and directed. (upto 5 storey) |
| 93 | M&L for water proof cement based putty @ 1 Kg (undiluted) per sqm mtr on layers over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surfaces with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 grit or above to make the surfaces free from dust etc by skilled labour as per following steps:- (1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with mixing capacity of min 2.5 kg putty per minute.(2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minute with a maximum pressure 3300 PSI.(3) Allow 6-8 hrs time to dry the putty surfaces complete all as specified and directed |
| 94 | S & F in repair Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, triple layer in construction white in colour hoisted and fixed in position including taking down existing water tank complete all as specified and directed. |
| 95 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.complete all as specified and directed. |
| 96 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using late vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 97 | Complete removal of existing treatment of wall/ceiling complete all as specified and directed |
| 98 | S&F in repair SS curtain rails 20mm dia fixing with brackets, stops, rollers khob lattu etc. complete all as specified and directed. |
| 99 | S&F MS chromium plated towel rail 20mm dia, D type, 600cm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed. ( code AQN 7711 equivalent of Kohler, Roca) |
| 100 | S&F MS chromium plated towel ring 12mm dia, round type, 150mm aperture fixed with CP brass screws including wooden/plastic beads complete all as specified and directed. ( cat part No AON- 7721 equivalent of Kohler, Roca) |
| 101 | M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone agg) as in seismic and other similar bands, coping, bed block or similar work including necessary form work complete all as specified and directed. |
| 102 | S&F Fibrette Tile made of 'Wood fiber Cement Composite' 1mm width wood fiber 15mm thick size 595x595/595X1195 mm having excellent noise absorption of 1 NRC as per ISO: 354, Density 400 Kg/ m3, meets Fire Ratings as per BS 476 Part 5, 6 and 7 class 1 and P, water resistant and thermal insulated. Installed on T24 grid system of 0.6mm thick Main 'T' length minimum 3000mm, web minimum 35mm to be placed at 600mm center to center and secondary cross 'T' of length 600mm web minimum 35mm inter locked, Wire Support for Main T to be taken at every 1200mm length wise and 600mm width wise, with a backing of 50mm 1000 GSM thick absorb wool tested as per Fire Retardant IS 15061-2002 for excellent results complete all as specified and directed. |
| 103 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 104 | M & L for RCC 1:2:4 type B1 as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, col etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.Note:- Reinforcement shall be measured and paid separately under respective item. |
| 105 | Use and waste flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffitsl (if any) of foundation and plinth beams; col and similar work; vertical or to batter complete all as specified and directed. |
| 106 | S&F TMT steel bars 6mm to 8mm dia. and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and directed. |
| 107 | S&F TMT steel bars 5mm dia and over, up to and including 10mm dia in stirrups spcers and binders complete all as specified and directed. |
| 108 | M&L for Providing and fixing internal wall panels on Light Gauge Steel Frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on 8mm thick fiber cement board conforming to IS 14862:2000 of category Ill type B (High pressure steam cured) as per standard sizes fixed with self-drilling/taping screws/fasteners@60cm c/c of approved Make, Screws shall be counter sunk rib head of1.60mm to 4mm thick of 8 to 1 0 gauge of length varying from25 to 45mm. Proper taping and jointing to be done usingfiber mesh tape and epoxy and acrylic based jointingcompound for seamless finish complete all as specified and directed. |
| 109 | S&F 5mm thick printed PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed. |
| 110 | S&F 5mm thick PVC sheet fillet of width fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed. |
| 111 | M&L for Roughening surfaces of old concrete floor / terrace by picking including taking down existing detoriated / decayed tar felt PCC tiles or any type of treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 250 m complete all as specified and directed. |
| 112 | M & L for 10mm thick rendering on roof surface/concrete surface in CM 1:4 complete all as specified and directed. |
| 113 | M&L for Apply oil bound bitumen primer @ 0.30 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface complete all as specified and directed. |
| 114 | Supply & Laying APP 3mm thick unrolled over the bitumen coated surface polymeric water proofing membrane Hyperplas standard wt not less than 3kg/sqm with 100mm over laps shall be sealed by flame as per manufactures instruction completely all as specified and directed. |
| 115 | M&L for Applying two coat of bituminous base aluminium paint including preparation and aluminium red oxide complete all as specified and directed. |
| 116 | M&L for applying water proof agent in two coats (horizontal and vertical layers) after cleaing the chajja and other building parts and removing the excess mortar then applying cement slurry making surface good making junction rounded, applying cure coat then finishing coats as per manufacturer instruction complete all as specified and directed |
| 117 | S&F 1st class HW 100×75mm handrails rounded or shaped with splayed faces in straightlengths and fixed complete all as specified and directed |
| 118 | S&F 1st class HW 50x50 Balusters, square wrought and fixed, with ends housed (square or splay) to handrails and treads or strings complete all as specified and directed |
| 119 | M&L for Preparation of newly or previously untreated, sizing incl filler coat of Thin varnish or lacquer or shellac varnish staing with spirit and two coat of Varnishing on wooden surfaces of any description, over and including 10cm in width or girth complete all as specified and directed |
| 120 | M&L for (except brick) for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and as directed.NOTE Brick shall be re-used retrived form item No. 02 |
| 121 | M&L for RCC M-25 design mix as in columns , pillars, piers, posts and struts etc. complete all as specified and directed.Note:- Reinforcement shall be measured and paid separately under respective item. |
| 122 | M&L for RCC (Design mix M-25) in beams, cantilevers, bressumers, lintels over 1.50 m span complete all as specified and directed.Note:- Reinforcement shall be measured and paid separately under respective item. |
| 123 | Use and waste flat fair finish formwork to sides of pillars, posts, struts, piers, columns etc square or rectanguar complete all as specified and directed. |
| 124 | Use and waste flat fair finish formwork to sides and soffits of floor beams, roof beams , beam haunchings girders, lintels, cantilevers etc to plain surface complete all as specified and directed. |
| 125 | S&F TMT steel bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and directed. |
| 126 | S&F framed work as in doors or gates of angle or other section ornamental with gussest plates, rails, braces, etc, complete drilled for fixing and incl steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hnging door fittings and fixing complete conferming to gde Fe 410-w complete all as specified and directed. |
| 127 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 128 | Demolition of PCC of any description and any position not otherwise provided for complete all as specified and directed. |
| 129 | M&L for 15 mm thick rendering in CM 1:4 on stone masonry surfaces or surfaces other than fair faces of brick work, finished fair and even complete all as specified and directed. |
| 130 | M&L for preparation of old/New surface ( Plastered or unplastered) of walls and applying two coat of water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat over coat of putty with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and directed. |
| 131 | S&F 8 to 10mm thick semi glossy/glossy stone wall, decorative finish wall size n exc size 0.20 sqm each external use over external wall surfaces over cement mortar 1:4 rendering coat complete all as specified and directed. |
| 132 | Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for. Including Tile Bedding layers and removing out side MD Land complete all as specified and directed. |
| 133 | M & L for cement concrete in foundations, filling and masss concrete type C2 1:3:6 (40mm graded aggregate) complete all as specified and directed. |
| 134 | Excavating in trenches in any type of soil , n exc 1.5 m wide and exc. 1.5 m in deep and n.exc 3.0m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out soil complete all as specified and as directed |
| 135 | Removal of excavated material (soil) to a distance exc 50 m n. exc 250 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. |
| 136 | Supplying and laying and jointing for (SN 8) DWCPE 180mm (OD)/ 163 (ID) conforning to IS-16098:2013 part -I with and incl jointing materials complete all as specified and directed |
| 137 | M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. |
| 138 | M&L for 15 mm thick rendering in cement mortar (1:3) on brick / concrete/ stone surfaces mixed with water proofing compound as per manufacturer instruction , finished even and smooth using extra cement complete all as specified and as directed |
| 139 | M&L for Precast cement concrete Type B-1 1:2:4 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:6 complete all as specified and as directed. |
| 140 | M&L for Brick work using old size bricks with sub class ‘B’ bricks in one brick thick honey comb walling built in cement mortar 1:4 complete all as specified and directed. |
| 141 | M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.42 sqm, in floors etc set over and including 15 mm thick cement screed in (1:4) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed. |
| 142 | M&L for 75mm thick PCC (1:2:4) Type C2 using 40mm graded stone agg as in plinth protection surface even and fair without using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and as diected |
| 143 | M&L for RCC M-20 design mix as in being cantiliver, chajjas, lintels and using 20mm graded stone aggregate complete all as specifed and directedNote:- Reinforcement shall be measured and paid separately under respective item. |
| 144 | Use and waste for rough finish surfaces flate or curved Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves, chajjas including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specifed and directed. |
| 145 | M&L for Brick work with Fly ash bricks straight or curved on plan exc 6m mean radius built in CM (1:6) all as specified and directed using old size bricks complete all as specified and directed. |
| 146 | S&F fancy type stainless steel draphery rods with brackets 20-25mm bore including stop roller lid and knobs etc cut to length as required of colour complete all as specified and directed. |
| 147 | S & F in repair for Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed, 15 mm, fancy type, chromium plated fixed complete. |
| 148 | S & Fin repair for fency type chromium plated Stop valves,(angle Cock) cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed , 15 mm fixed complete all as specified and directed. |
| 149 | S & F for PVC connections 15 mm size with PTMT nuts of length 600mm fixed complete all as specified and directed. |
| 150 | Taking down steel tubing and connections including cleaning for refixing or removal form site for 25mm bore pipe all as specified and directed . |
| 151 | Taking down steel tubing and connections including cleaning for refixing or removal form site for upto 20mm bore pipe complete all as specified and directed. |
| 152 | Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and directed. |
| 153 | Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and directed. |
| 154 | PVC (SWR) floor trap / Nahani trap with grating 75 mm dia incl jointing with solvent cement complete all as specified and directed. |
| 155 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated colour PVC sheet reinforced with M.S square tube in opening as per specification including making good to the disturbed surfaces and matching existing treatment (cemnt base paint/distemper/white wash/plastic paint) etc complete all as specified and directed. |
| 156 | S&F alluminum alloy, anodised, sliding door bolt with hasp & staple (bolt type) and length of 300 mm long etc. complete all as specified and directed. |
| 157 | Dismentaling of timber scantling as in fillets, rails posts rafters purlin etc under 40 Sqcm in section as in unframed work complete all as specified and directed |
| 158 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 60 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 159 | M & L for 18mm thk lnsulated PVC Wall Lining consisting of PVC Insulated Panels with single side Prelam PVC sheet used in-stead of Plain colour sheet as in cupboard, wardrob and similar works etc work to be done at site complete all as specified and directed. |
| 160 | S&F for continuous (Piano) hinge 40 mm brass bright finish or electro galvanized complete all as specified and directed. |
| 161 | S&F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed. |
| 162 | S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-22 complete all as specified and directed. |
| 163 | S&F in repair Brass Chromium plated kichen sink/ WHB mixer for mixing hot & cold water screwed down for 15mm bore iron pipe in sink and WHB mixer etc. complete all as specified and directed . (Make/ sample approved by GE) Jaquar (FLR-5025B) or equivalent of Kohler, Roca |
| 164 | S & F in repair WALL Mixer 3 in 1 system with provison in hand and head shower with 115 cm long band pipe connecting with lags and wall flange etc complete all as specified and directed.Make:- ( Cat No FLR - 05281 N of Jaquar or equivalent of Kohler, Roca ) |
| 165 | S&F in repairs Towel Rack etc complete all as specified and directed.Make:- ( Cat No AQN 7781 of Jaquar or equivalent of Kohler, Roca ) |
| 166 | S & F in repairs Toilet paper holder etc complete all as specified and directed. Make:- ( cat part No AHS 1553 of Jaquar or equivalent of Kohler, Roca) |
| 167 | S&F in repair Looking Mirror with PVC moulding, complete all as specified and directed.Make:- Jaquar or equivalent of Kohler, Roca |
| 168 | S&F in repair Shower OH, complete all as specified and directed. Make- ( code OHS 1757 of Jaquar or equivalent of Kohler, Roca ) |
| 169 | S&F in repair Shower Arm, complete all as specified and directed. Make:- ( code SHA 479L300 of Jaquar or equivalent of Kohler, Roca ) |
| 170 | S&F in repair Hand Shower, complete all as specified and directed.Make:- ( code HSH 49537 of Jaquar or equivalent of Kohler, Roca) |
| 171 | S&F in repair Corner Glass Shelves,complete all as specified and directed. Make:- ( code CAN 1173 Jaquar of or equivalent of Kohler, Roca) |
| 172 | S&F in repair Tumbler holder, complete all as specified and directed. Make:- ( code AQN 7741 of Jaquar or equivalent of Kohler, Roca) |
| 173 | S&F in repair, chromium plated glass shelf of size 22'' complete all as specified and directed.Make:- Cat No AQN-7771 of Jaquar or equivalent of Kohler, Roca |
| 174 | S&F in repair, PVC Bath cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size. complete all as specified and directed.Make:- As per Cat No. 554 of Prayag or equivalent Make as approved by GE. |
| 175 | S&F in repair POP cornis of garth exc 100mm nexc 200mm shape and design as approved fixed to wall/ceiling with PVC rawl plug/ MS screw as required complete all as specified and directed. |
| 176 | S&F of ball bearing runners 45 mm telescopeic chennal 20 inch full extendion load capacity 50 kgs smooth closing after gentle push complete all as specified and directed. |
| 177 | S&F of stainless steel handles 100 mm size for kitchen cabinet shutters make-Hettich ,Ebco,Prime) complete all as specified and directed. |
| 178 | S&F in repair Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl 3mm dia GI wire used as hanger complete all as specified and directed |
| 179 | S&F 12 mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed. |
| 180 | S&F 8mm thick Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed. |
| 181 | Taking down carefully aluminium point wiring (light, fan, bell, socket, power point etc.) with or without conduit, casing caping, along with all connected accessories such as ceiling rose, switches, sockets, switch boards, fan regulator,light fittings etc., complete and all as specified & directed. Note :- 1. Contractor has to submit existing bldg. inventory items having details of serviceable and unserviceable and physically verified with JE E/M during the handing taking of sites and before commencement of work.2. If work commence without signing of E/M inventory then contractor will be solely responsible for missing of E/M items and decision of engr- in- charge will be final in this regard .3. All E/M items received from site as a schedule of credit should be stored at location decided by engr-in-charge and should be taken out from bldg. premises/ stored location with confirmation |
| 182 | M&L for point wiring with 1.5 Sq mm, FRLSH, PVC insulated, single core, unsheathed, multi stranded 1100 volts grade, copper conductor cable drawn through concealed conduit and including concealed PVC rigid non metalic conduit of size 19/20mm, on ceiling/wall, with and including continuous 1.5 Sqmm, FRLSH, PVC insulated single core multi stranded copper conductor cable earth continuity conductor connected to common earth and earth dolly and including sunk metal sheet enclosure rectangular terminal boxes of suitable size and white cover plates & frame plate suitable for mounting modular switches, sockets etc and making good the disturbed surfaces with cement sand mortar 1:3 to match with the existing surfaces for light points complete all as specified and directed. |
| 183 | ~ditto~ all as per item No. 182 here abovebut for one Fan Point controlled by one switch. complete all as specified and directed. |
| 184 | ~ditto~ all as per item No. 182 here above but for one Bell Point controlled by one switch complete all as specified and directed. |
| 185 | ~ditto~ all as per item No. 182 here in before but with one 3 pin, 5 amps, socket outlet on the same board complete all as specified and directed. |
| 186 | ~ditto~ all as per item No. 182 here in before but with one 3 pin, 5 amps socket outlet on independent board complete all as specified and directed. |
| 187 | ~ditto~ all as per item No 182 here in above but with 1100 Volts grade copper stranded conductor FRLSH cable of size 2.5 Sqmm main & with 2.5 Sqmm earth multi-strand copper conductor cable as earth wire for 3 pin switch socket outlet 15 Amp on Independent board complete all as specified & directed. |
| 188 | M&L for Sub main wiring in repair with two single core PVC Insulated cable two run of size 4.0 Sqmm multi-strand copper conductor FRLSH cable 1100 volts grade drawing in and including PVC conduit, medium grade not less than 25 mm dia with all conduit accessories and one run of 4.0 Sqmm multi-strand copper conductor FRLSH cable as continuous earth wire .Including taking down old unsv . complete all as specified & directed.Note : - Two run of 4 Sqmm phase wire & one run of 4 Sqmm earth wire cable & one run of conduit shall be measured as one unit run. |
| 189 | M&L for Sub main wiring with two single core PVC Insulated cable two run of size 6.0 Sqmm multi-strand copper conductor FRLSH cable 1100 volts grade drawing in and including PVC conduit, medium grade not less than 25 mm dia with all conduit accessories and one run of 6.0 Sqmm multi-strand copper conductor FRLSH cable as continuous earth wire .Including taking down old unsv . complete all as specified and directed. Note : - Two run of 6 Sqmm phase wire & one run of 6 Sqmm earth wire cable & one run of conduit shall be measured as one unit run. |
| 190 | Supply and fix in replacement modular bell push, 1 module, 6 amps, complete all as specified & directed. |
| 191 | Supply and fix bell ding dong AC 230 volts, single pole complete all as specified & directed. |
| 192 | Supply and fix in replacement modular switch type 230/ 250 volts, 6 amps, 1 module, single pole, one way, complete all as specified & directed. |
| 193 | Supply and fix in replacement modular socket out let multi purpose 2 in 1, 2/3 pin, 6 amps,2 module flush type, ISI marked complete all as specified & directed. |
| 194 | Supply and fix in replacement switch modular 16 amps, flush type, ISI marked complete all as specified & directed. |
| 195 | Supply and fix in replacement modular socket 2/3 pin combined, 6/16 amps 2 module, flush type, ISI marked complete all as specified & directed. |
| 196 | Supply and fix in repair ceiling rose surface bakelite, three terminal complete all as specified & directed. |
| 197 | Supply and fix in replacement Smart bright Batten Series, LED luminaire using LEDs 22/20 watt, natural white, 2200 Lumen, THD max 10 % ,CRI min 80 % with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output with wide voltage protection range, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start ,with 3 core flexible copper wire 1.5 sqmm and connecting accessories ,Inbuilt driver unit Suitable for wall and ceiling mounting using brackets (supplied along with The Luminaire has been tested as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), report has established conformity of the product(s) to the requirements of the Standard/Specification complete all as specified and directed. |
| 198 | Supply and fixing in repair round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 199 | Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed. |
| 200 | Maintenance and checking of ceiling fan/exhaust fan of any size/type/make, checking the serviceability of all parts, electric connections etc. Preparation of old painted surfaces and painting with two coats of synthetic enamel paint of approved shade, reconnecting/hanging in original position, reconnecting the electric cables and testing complete all as specified and directed. |
| 201 | Supply and fix in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed. |
| 202 | Supply and fix in replacement LED street light / security light fitting 35/36 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete all as specified & directed. |
| 203 | Supply and fixing IN repair LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed/surface type, as directed, with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified & directed. |
| 204 | Supply and fix rigid non metallic, medium grade, PVC conduit, concealed type of size 25 mm with all accessories such as couplers, lock nuts, saddles, pipe hook, tees, bends, etc., including cutting chases for conduits and making good the disturbed surface with PCC as per site requirement complete all as specified & directed. |
| 205 | Supply and fix in replacement modular stepped type electronic fan regulator flush type, two module on the existing phenolic laminated etc., as required, single pole, 240 volts, grade 120W watts, 2 Module heavy duty and ISI marked complete all as specified & directed. |
| 206 | S&F in replacement sheet metal enclosure MCB DB double door , Triple pole and neutral, 440 volts, 4 way with 200 Amp, 10 KA breaking capacity rated copper bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed. |
| 207 | S&F in replacement MCB Triple Pole and Neutral 63 Amps,415 V ,10KA breaking capacity complete all as specified & directed. |
| 208 | S&F in replacement MCB Single Pole and Neutral 240Volt,upto 32Amps, 'C' series,10KA breaking capacity complete all as specified & directed. |
| 209 | Supply & fix in repair RCBOs For earth Leakage , overload & short Circuit Protection Double Pole 20A & 30 mA complete all as specified and directed. |
| 210 | S&F in replacement MCB Single Pole 240Volt, upto 40Amps,10KA breaking capacity complete all as specified & directed. |
| 211 | Supply and laying & testing and commisioning LT underground cable 1100 volts grade,in repair XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of the Size of 16sqmm x 4 core and as per relevance IS code complete all as specified and directed. |
| 212 | Supply and laying & testing and commisioning LT underground cable 1100 volts grade,in repair XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of the Size of 10 sqmm x 2 core and as per relevance IS code complete all as specified and directed. |
| 213 | Supplying and laying DWCPE pipe OD 50 mm , ID 40/38 mm complete all as specified and directed. |
| 214 | Earthing complete for various equipments with galvanised steel earth plate electrode 600 x 600 x 6mm thick directly burried in the ground (earth pit not less than 2.25 metre deep below ground level) with top edge of earth plate not less than 1.5 m below the ground level, connected to G.I wire 4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, GI pipe 20mm bore light grade for protection of earthing strip, PCC chamber 1:4:8, type C-1 using 20mm graded stone aggregate, internal surface of concrete chamber plastered with 12mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge ( 0.63) 8 mesh per linear inch, 50mm thick cover of RCC 1:2:4, type B-1, using 20mm graded stone aggregate, reinforced with 8mm TMT bar at 100mm center to center both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR Part-I and as specified including excavation and earth work and connecting the earthing to an earthing test point as specified and testing on completion all as specified & directed.Note:- Unit rate quoted is inclusive of earth lead and protection pipe upto 7.5 metre from earth plate. |
| 215 | Supply and laying in replacement & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size of 2 core x 6 sqmm and as per relevance IS code complete all as specified and directed. |
| 216 | M&L dry river washed and screened dry sand for filling in trenches below and around the cable for cushioning including punning down as specified inrelevant clause of SSR Part I complete all as specified and directed. Note:- Punned thickness shall only be measured and paid. |
| 217 | Supplying and laying unreinforced precast concrete cable cover, class LV Type 2 flat, size 300mm x 180mm x 40mm complete all as specified and directed. |
| 218 | Supply, fix in repair for LED post top lantern 40 watt light fitting made of cast aluminium spigot housing with decorative opal acrylic diffuser with IP 65 protection complete with all accessories fixed on GI pipe 50 mm dia complete all as specified and directed. |
| 219 | Supply and fix in repair junction box made out of polycarbonate with IP 55/IP 65 protection of size 155 x 210 x 92 mm,having terminals for termination of cable with necessary nuts and bolts , including -02 Nos polycarbonate cable gland , 01 Nos DIN rail for mounting of MCB and 01 No, MCB SP, 10 KA, 6 Amps in and including fixing clamp of FI 50 x 6mm with necessary nuts and bolts complete all as specified and directed. |
| 220 | Supply and lay pipe galvanized, “Light class”, including fittings of dia 40 mm complete all as specified and directed. |
| 221 | S&F decorative wall lamp LED light fitting made up of Polycarbonate ,Cylindrical shape ,with LED lamp 9 Watt complete with fixing arrangements on wall complete all as specified and directed. |
| 222 | Supply and Fixing in replacement Sheet metal enclosure for DBs when MCBs to be Used, 12 way, SPN, double door type, 240 Volt suitable capacity busbar complete all as specified and directed.(Note : MCBs will be Measured separately) |
| 223 | Supply and Fixing in replacement Sheet metal enclosure for DBs when MCBs to be Used, 4 way, SPN, double door type, 240 Volt suitable capacity busbar complete all as specified and directed.(Note : MCBs will be Measured separately) |
| 224 | S&F in replacement MCB Triple Pole and Neutral 40 Amps,415 V ,10KA breaking capacity complete all as specified & directed.Make: Legrand cat no :4086 83 or eq in SEIMENS /GE |
| 225 | S& F WALL FAN of sweep 400 mm (16 inches), 230V AC, 50 Hz single-phase supply, Minimum 1300–1400 RPM with a minimum air delivery rate of 65 m³/min, 3-speed control via pull cords or rotary switch (low, medium, high), 3 polypropylene or ABS plastic blades, sturdy fan guard complying with safety standards, and adjustable vertical tilt with oscillating function , Compliance with IS 555 / relevant BIS standards and a minimum 1-year manufacturer warranty complete all as specified and directed. |
| 226 | Schedule of credit of Amount Rs. 1,27,177.00 to be deducted during AOC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender