Water Resources and Irrigation Government Departments Closing in 9 days TDR #58547225

Tender For Installation Of Siripur-Ii L.I. Projects Under Barkote Block In Debagada District Of L.I. Division, Sambalpur

Issued by Government Departments · Deogarh, Odisha
Tender Value
56.70 Lakhs
Estimated cost
Bid Submission
30 Nov 2026
9 days left
EMD
56701
Bank guarantee accepted
Document Fee
11800
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Deogarh → Odisha
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Installation Of Siripur-Ii L.I. Projects Under Barkote Block In Debagada District Of L.I. Division, Sambalpur

BOQ

Name of Work:- Installation of Siripur-II L.I. Projects under Barkote Block in Debagada District of L.I. Division, Sambalpur
Sl. No. Item Description
1Part-A
2Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-in-charge.
3Excavation in hard soil such as Hard stiff clay, stiff black cotton, hard red earth, shales, moorum ordinary gravels, within 50m. Initial lead and 1.5m. Initial lift including rough dressing and breaking clods and stacking rubble or spreading and leveling within the site as the case may be etc; complete.asper direction of the Engineer-in-charge.(Mechanical 60% & Manual 40%)
4Filling in F&P with excavated materials including well watered and rammed.in hard soil such as Hard stiff clay, stiff black cotton, hard red earth, shales, moorum ordinary gravels, within 50m. Initial lead and 1.5m. Initial lift including rough dressing and breaking clods and stacking rubble or spreading and leveling within the site as the case may be etc; complete.asper direction of the Engineer-in-charge.(Mechanical plus manual )
5Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge.
6Cement concrete (1:4:8) with 4cm size h.g.b. crusher broken metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc. complete as per the direction of the Engineer-incharge.
7Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6)in foundation & plinth complete as per the Engineer-incharge
8Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) in super structure etc. complete as per the Engineer-incharge
9Cement concrete (1:2:4) with 12mm size black h.g.b. crusher broken chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge.
10Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-incharge(a)Roof slab, chajja, carnice etc
11b)Lintel
12c)Plinth band, foundation, footing base of column etc
13d)Beams & Columns
14e)Walla & fins
15Labour charges for MS reinforcement for RCC work including cutting, bending & tying the grills and placing in position including cost of binding wire 18 to 20 gauge & HYSD steel bar ( FE 415/ FE 500 )
16R.C.C. work in C.C. (1:2:4) including hoisting & laying & curring for 28days using 12mm. Size clean black hard granite crusher broken chips of approve quality and from approve quarry including cost taxes conveyance charges of all materials to the worksite with supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
1712mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
18Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
19Dry brick rammed Khoa (10 cm) thick well watered and rammed.
2025mm thick AS flooring with CC (1:2:4) using 12mm sizeblack h.g.c.b chips of approved quality from approved quarry including watering and curing with cost, taxes, royality and conveyance charges of all materials to the work site and supply of all labour, T & P required for the work etc. complete
212.5 cm thick grading concrete (1:2:2) with 6 cm size h.g chips
22Cement washing two coats over plastering
23Finishing walls with plastic emulsion paint of approved shade on new work two coat to give an even shade excluding cost of paint.
24Wall painting two coats with weather coat paint of approved shade excluding cost of paint.
25Cost of plastic emulsion paint
26Cost of weather coat cement paint
27Painting of red oxide primer of approved quality for priming over iron work including cost, taxes etc. complete
28Painting of enamel paint of approved quality and colour for painting over iron work including cost, taxes etc. complete
29MS panel door double leafed with MS frame overall size of 1.20x1.98 mtr for door and 0.90x0.90 mtr for window, shutter of 20 gauge CR sheet panel as per approved size and specification etc. including fitting & fixing the door etc. complete
30Writing charge of required information and data on both side of the transperancy pillar including supplying of approved paints and required material for writing etc. complete as per the direction of the Engineer-incharge.
31Supplying all materials, labour, T&P for jointing of 250 mm outer dia High Density Polythylene Pipes of specified material grade & pressure rating by butt fusion welding method as per speciication & laying in tranches including testing including all cost etc complete as per direction of the Engineer-in-charge
32Supplying all materials, labour, T&P for jointing of 200 mm outer dia High Density Polythylene Pipes of specified material grade & pressure rating by butt fusion welding method as per speciication & laying in tranches including testing including all cost etc complete as per direction of the Engineer-in-charge
33Supplying of 250 mm dia PN - 6 PE - 80 HDPE Pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation to work site in complete shape
34Supplying of 200 mm dia PN - 4 PE - 80 HDPE Pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation to work site in complete shape
35Filling the foundation and plinth with excavated material as directed by the Engineer-incharge. A) Hard Soil
36Supplying & fitting of RCC ventilators
37Centrifugal Monoblock pumpset total head of 28 mtr capable to discharge 1700 LPM with 15 HP/11 KW squirrel cage induction motor fitted with bronze impeller TB-2 of iS 318/1981, companion flanges & class 'F' insulation suitable for operation 415 volt + 6% - 15%, 3 phasde, 50 Hz aC power supply, delivery = 100x100 mm with BEE star rated energy efficiency pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership network for easy availibility of spares
38Control panel with automatic star delta starter sheet steel enclosure vsuitable for operation of squirrel cage induction motor up to 15 HP with 16 Amp.(AC-3) duty contractor at 415 volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & No volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The starter should provide dependable protection against over load and single phasing fitted with Volt meter, Ammeter, MCB in complete shape including indicator lamp
39Cost of 63 Amp -400 V.T.P. Main Switch confirming to IS No.4064
40Cost of panel board made out of 18 gauge CR sheet
414 KVAR Capacitor
42Motor Hood (size 0.45x0.45x0.60 mtr ) made with 18 SWG cold rolled mS sheet with one coat of red oxide primer and two coats of smoke gray / navy blue enamel paint both side (inside & outside) suitable to cover centrifugal monoblock Pump set from 10 to 15 HP and having provision for attachment with the groves on rear side of the panel board
43Base Plate made of MS Channel with holes for Motor & Panel
443 x 16 mm² Tarpedore cable XLPE ( cross link polyethylin ) confirming to IS: 7098 (Part-II) including laying below 0.90 mtr of the ground and filling the excavated materials including watering and ramming
457/20 P.V.C. Wire
46100 mm dia nominal bore GI pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt - 1 of 2004) with socketed at one end and the other end protected with plastic thread protector. The socket confirming to IS - 1239 (pt - II / 1992) with latest amendments in random length of 4 to 7 mtrs. Each pipe should bear ISI certification & manufacturer's name/ trademark
47100 mm dia GI Bend IS No. 1239(pt-II/1992)
48100 mm dia GI flange IS No. 6392 / 1971
49250x100x100 mm PVC/G.I./M.S. Y - Joint
50Electrical earthing
51Misc. Welding charges for \\"Z\\" joint, \\"S\\" bend, etc.
52100mm C.I. Foot Valve should be of swing type friction less with single disc confirming to iS - 4038/1979 of reputed brand
53100mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement
54250mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement
55200 mm dia Butterfly valve as per IS - specification
5650 mm dia CI AR valve with saddle and riser pipe confirming to IS 14845 with ISI mark
57250x250x200 mm dia spigot moulded reducing HDPE Tee 10 kg
58250 mm dia HDPE Elbow spigot design 6 kg
59250 x200 mm HDPE Reducer
60250 mm dia HDPE end cap
61200 mm dia HDPE end cap
62200x200x110 mm HDPE/GI Raiser tee set with bend closing and opening arrangement
63250 mm dia HDPE Tail piece 160 mm long
64250 mm dis MS pipe (Medium Duty ) 5.4 mm thick
65250 MM Dia MS Flange
66Construction of out let for Tee Tank
67Supply of small T & P Kit comprising of hand gloves - 1 pair, tester - 1 no, 8\\" cutting plier - 1 no, 12\\" sly wrench - 1 no, 12\\" screw driver - 1 no, 24/27 & 21/23 DE spanner - 2 nos, 24/27 & 21/23 Ring spanner - 2 nos of Taparia make
68Labour charges for installation of 20 HP openwell submersible Motors including transportation from village to work site, fitting & fixing of base frame, fitting & fixing suction and delivery pipe to motor, other fitting materials including cutting, welding etc. complete as per the direction of the Engineer-incharge.
69Cost of Rubber Insertion and nut Bolt etc.
70Labour charges for delivery and fitting including fitting of priming Tee, sluice Valve, NR Valve, air release valve and riser Tee etc and installation
71Cost of river embankment cutting, cleaning ; fitting of suction & delivery fittings with flanges, bend, foot valve, sluice valve, NR valve etc including cost 1/8\\" rubber insertion, Nut nolt, white lead paint etc vomplete
72Welding at site including supply of Welding machine, Generator set, all labour, materials and T & P
73Part-B
74Construction of 3 phase 11 KV Line as per REC standard confirming to RE Rules 1956 with 300Kg. 10 mtrs.long PSC Pole ( cost excluded ) support in 80Mtrs. Span 55 sqm. AAA Conductor, 11 KV \\"V\\" cross arm with required nos.of 11KV T &C disc.Insulators and 11KV Pin insulator,carping & padding of poles, danger board at each pole,anticlimbing devices. Stay set at each bending Point and double stay at end point with 18mm G.I. H.T. Stay, concreting of stay with anchor plate,guarding at road crossing etc. including cost of materials,labours, transportation, inspection and commissioning etc. complete.
75Cost of LT line with 35 mm² AB Cable 3 phase 4 wire on 8 mtr x 200 kg PSC pole ( 30 mtr span ) including distribution box and pearsing connector ( excluding pole cost )
76Construction and errection of 11/0.4KV , D.P. mounted substation of different capacity confirming to RE Rules 1956 mounted on 2.44mtr. Long structure , supported in 300 Kg 10 mtrs. Long PSC Poles, Transformer hard channel and top channel made of 2.8mtrs. long 100X50X6 mm M.S. Channel, Transformer belting on 2.8 mtrs. long 50X50X5 mm M.S. angle (all REC.SPN.Std F-3) with all accessories like3 poles 11 K.V. HG Fuse (F-5) & AB Switches (F-9) both mounted on 2.5 mtrs. long 75X40X6 mm M.S. Channel and supported by 1mtr. long 50X50X5 mm M.S. angle with 3nos. 11 KV lightening Arrestors and distribution box, Pipe earthing(F-2), including cost of 50 sqmm. 3.5 core PVC Cable carping and padding of poles, danger board at each poles, Anti climbing Devices & all other necessary fitting i.e. required size nuts & bolts, brackets Cable sockets etc., construction of barbed wire fencing with double leaf MS Gate with metal spreading, including cost of all materials , labour transportation complete with liasoning for testing inspection & commissioning ( excluding cost of PSC pole & including cost of Transformer 11 / 0.4 KV level - II, Star - II ) 63 KVA Sub-station
77Materials for Tapping pole without pole
789 mtr 300 kg PSC pole
7910 mtr 400 kg PSC pole
80Spike provisin
81Boundary wall of S/S with metal spreading & MS Grill gate
82Electrical earthing
83pumpchamber wiring Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58547225
AUTHORITY Government Departments
TENDER VALUE 56.70 Lakhs
LAST DATE 30-11-2026
Authority
Authority Name Orissa Lift Irrigation Corporation Limited
Work Description Tender for Installation Of Siripur-Ii L.I. Projects Under Barkote Block In Debagada District Of L.I. Division, Sambalpur
Basic Detail
Tender No EEOLICSBP-04/2026-27
Bidding Type Tender
Location
City Deogarh
State Odisha
Key Dates
Publish Date 16 Nov 2026
Submission Date 30 Nov 2026
Open Date 01 Dec 2026
Finance
Tender Value 56.70 Lakhs
Tender Fee 11800
EMD 56701
Exemption Available
Document List
13cf6a02-09f1-408b-9dfe-33087832b8b9.html
BOQ_621080.xls
Tendernotice_1.pdf
Tendernotice_2.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 16, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 30, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 9 days
Dec 01, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 10 days

Tender Documents

Download All (ZIP) ↓
html

13cf6a02-09f1-408b-9dfe-33087832b8b9.html

xls

BOQ_621080.xls

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender