Water Resources and Irrigation Government Departments Closing in 11 days TDR #58543499

Tender For Installation And Energisation (Revival And Reinforcement) Of Jadapali-I,Ii, Badjore-Iv, Badteneda-I,Ii And Balipata-I,Ii,Iv Old Clips Under Tarabha Block (State Plan 2026-27)

Issued by Government Departments · Sonepur, Odisha
Tender Value
77.37 Lakhs
Estimated cost
Bid Submission
30 Nov 2026
11 days left
EMD
77373
Bank guarantee accepted
Document Fee
11800
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Sonepur → Odisha
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Installation And Energisation (Revival And Reinforcement) Of Jadapali-I,Ii, Badjore-Iv, Badteneda-I,Ii And Balipata-I,Ii,Iv Old Clips Under Tarabha Block (State Plan 2026-27)

BOQ

Name of Work:- Installation and Energisation (Revival and Reinforcement) of JADAPALI-I,II, BADJORE-IV, BADTENEDA-I,II and BALIPATA-I,II,IV Old CLIPs under Tarabha Block (State Plan 2026-27)
Sl. No. Item Description
1Earthwork in excavation of foundation in hard soil such as Hard stiff clay, stiff black cotton, hard red earth, shales, moorum ordinary gravels etc within 50m.Initial lead and 1.5m. Initial lift including rough dressing and levelling the bed and depositing the excavated materials within initial lead at nearby the worksite for reuse including breaking clods and stacking rubble for spreading and leveling as the case may be etc complete as per direction of the Engineer-in-charge. (Excavation by mechanical means 60% & manually 40%)
2Filling in F&P with excavated materials in layers not exceeding 0.30m including breaking clods within 50m. initial lead including leveling the tranches as the case may be etc complete as per direction of the Engineer-in-charge.(Quantity by means of Mechanical 60% & mannually 40% i.e. of respective item No. 1 above)
3Earth work excavation of foundation in hard soil within initial lead of 50m & lift of 1.5m including dressing and levelling the bed etc.as direction of Engineer-in-charge
4Filling in F&P with excavated materials including well watered and rammed.(2/3 of respective earth work) as direction of Engineer-in-charge
5Filling F and P with sand, well watered and rammed as direction of Engineer-in-charge
6Cement concrete (1:4:8) with 4cm (1½”) size hard granite metal (Crusher Broken) as direction of Engineer-in-charge
7RCC/Cement Concrete (1:2:4) with 12mm (½”) size hard granite chips (Crusher broken) as direction of Engineer-in-charge
8Flyash. Brick masonary in cm(1:6) in foundation and plinth (25cm X 12cm X 8cm size) as direction of Engineer-in-charge
9Flyash Brick masonary in cm(1:6) in Superstructure work ( 25cm X 12cm X 8cm size ) as direction of Engineer-in-charge
1012mm thick Cement plaster in CM (1:6) over brick work as direction of Engineer-in-charge
11Cement punning over plastering as direction of Engineer-in-charge
12Rigid smooth centering shuttering for R.C.C. work including all cost etc. complete Column, Landing Balcony, Projection .etc.as direction of Engineer-in-charge
13Rigid smooth centering shuttering for R.C.C. work including all cost etc. complete in Column base etc.as direction of Engineer-in-charge
14Rigid smooth centering shuttering for R.C.C. work including all cost etc.Plinth Bend Lintel roof slab chajja etc.as direction of Engineer-in-charge
152.5 cm. thick A.S flooring with cement concrete (1:2:4) including punning using 12mm size C.B. chips including at cost etc. complete .as direction of Engineer-in-charge
16Supplying of M.S. reinforcement for R.C.C. work including cutting bending, binding & typing the grills & placing in position including cost of binding wire & reinforcement 18 to 20 guage per Qntl..as direction of Engineer-in-charge
17Painting two coats with approved paint on steel.as direction of Engineer-in-charge
18Cost of pump chamber wiring with all cost of wiring materials, labour etc complete.as direction of Engineer-in-charge
19Distempering two coats to walls with distermper of approved shade on new work to give an even shade etc.as direction of Engineer-in-charge
20Finishing walls with water proofing cement paint of approved shade on new work ( 2 coats ) to give an even shade etc complete etc.as direction of Engineer-in-charge
21Cost of M.S. Pannel Iron Door with M.S.Frame etc including fixing ( 1.00 X 1.80)etc.as direction of Engineer-in-charge
22cost of M.S. Pannel Iron window with M.S.Frame etc including fixing ( 0.90 x 0.75)etc.as direction of Engineer-in-charge
23Cost of outlet etc.as direction of Engineer-in-charge
24Labour charges for writing reqd. data & information on the Brick pillar etc.as direction of Engineer-in-charge
25Cost of 200 mm Ø PVC. pipe (Cl-I) 2.5 Kg/cm2 to deliver water at highest counter in the following Nominal diameter, Grades of materials, Pressure rating including the rates of ex-factory, transportation, pre & post inspection, Cess etc complete .as direction of Engineer-in-charge
26Cost of 200 mm Ø PVC. pipe (Cl-II) 4.0 Kg/cm2 to deliver water at highest counter in the following Nominal diameter, Grades of materials, Pressure rating including the rates of ex-factory, transportation, pre & post inspection, Cess etc complete .as direction of Engineer-in-charge
27Labour charges for laying and fitting of 200/250 mm Ø PVC pipe as direction of Engineer-in-charge
28Cost, supplying of 200mmx200mmx110mm dia Weldless G.I.Tee (3.6mm thickness) with bend, closing and opening arrangement of reputed brand including all cost, conveyance, cess etc complete but excluding cost of GST etc.as direction of Engineer-in-charge
2915HP/11.25 KW Energy efficiency Monoblock pump set of total head 24 mtrs having discharge 1700 LPM with squirrel cage induction motor fitted with bronze impeller TB-2 of IS 318/1981, companion flanges & Class \\"F\\"insulation suitable for operation 415 volt +6%-15% 3 phase, 50Hz AC poweer supply suction/deliveery= 100mmx100mm with BEE 3 Star rated energy efficiency Pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership net work for easy availability of spares confirming to IS specification(a) Casing: FC 200 as per IS 210/1978 (b) Impeller: Bronze grade LTB-2 of IS 318/1981 including all cost, conveyance, cess etc complete etc.as direction of Engineer-in-charge
30Control Pannel with Automatic Star delta Starter, sheet steel enclosure suitable for operation of Squirrel cage induction motor up to 15 HP with 20 Amp (AC -3) duty contractor at 415 Volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & no volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The Starter should provide dependable protection against over load and single phasing fitted with Volt Meter, Ameter, MCB in complete shape including Indicator Lamp reputed brand of ISI specification including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
3163 AMP Triple Pole Mainswith confirming to IS No.4064(Part I & II) with ISI marking of reputed company having utilisation capacity cagegory AC- 22 reputed brand of ISI specification including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
32Empty Outdoor Irrigation Pannel Board size (0.45mtx0.25mtx1.20m of 18 SWG Cold Rolled M.S Sheet with 4 legs of 300 size with one coat of Red Oxide Primer and two coats of Smoke grey /Navy blue two coats of powder coated paint of approved quality on both side (Inside & Outside) suitable to mount 3Phase Starter, Main Switch and Capacitor inside the Panel Board vertically over 18 SWG M.S.Sheet and the danger board fixed on the top of the Panel Doorreputed brand of ISI specification including all cost, conveyance, cess etc complete but excluding cost of GST
33Motor hood size (0.45mx0.45mx0.60m) made with 18 SWG (cold rolled M.S.Sheet with one coat of red axide primer and two coats of powder coated paint of approved quality on both side (inside & outside) suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for attachement with the groves on rear side of the pannel board of approved brand including all cost, conveyance, cess etc complete as per the direction of the Engineer-In-Charge
34Motor base plate made with M.S angle with one coat of red axide primer and two coats of powder coated paint suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for hole for fixing nut & bolt of approved brand including all cost, conveyance, cess etc complete as per the direction of the Engineer-In-Charge .
35Base frame for panel (size 0.40mx0.20m) made with 3 size M.S. channel having suitable holes for fitting of panel Board, coloured with one coat of red oxide primer and two coats of powder coated paint of approved quality & Base frame for motor (size 0.50mx0.27m) made with 3 size M.S. channel having suitable holes for fittings of different size and make 3 phase centrifugal monoblock pump set from 10 HP. to 15 H.P. coloured with one coat of red oxide primer & two coats of powder coated paint of approved quality reputed brand of ISI specification including all cost, conveyance, cess etc complete complete as direction of Engineer-in-charge
366 KVAR Power Shunt Capacitor with ISI mark of of reputed approved brand of including all cost, conveyance, cess etc complete complete as direction of Engineer-in-charge
37Installation for delivery and fitting including fitting of priming Tee, sluice Valve, NR Valve, air release valve and riser Tee ,MB Pump set,electrical instalation ,nut & bolt,rubber insertion, 4mm2 PVC wire,misc welding all complete etc
383x16 sqmm PVC insulated (HD) tropoder armoured Electric Cable with alluminum conductor for use in 3 phase power system of working voltage upto & including 1100 volts at 50Hz confirming to IS 7098 (Pt-II) of approved brand of ISI marked including all cost, conveyance, cess etc complete complete as direction of Engineer-in-charge
39100mm dia nominal bore G.I.pipe having wall thickness 4.5mm electrical resistance welded of medium class confirming to IS- 1239(part-1/2004) with latest ammendments, screwed at both ends as per IS-554 with socketed at one end and the other end protected with plastic threaded protector including its transportation and unloading at L.I.P. site. The socket confirming to ISI 1239(part II/1992) with latest ammendments in random length of 4 to 7 mtr.Each pipe should bear IS certification and manufacturers name/trade mark complete as direction of Engineer-in-charge
40100mm dia G.I.Bend ( Medium Duty) conforming to IS No-1239 (part II/1992) with ISI mark of reputed brand including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
41100mm dia C.I. Screw boss Foot Valve of swing type friction less with single disc conforming to IS-4038/1979 of reputed brand with ISI mark of reputed company having wide dealership network including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
42100mm dia G.I.Flange (Medium Duty) conforming to IS No-6392/1971 with ISI mark of reputed brand including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
43100mm dia C.I.Double Flanged Non Return Valve (NR) swing type PN-1.0 (IS-5312(Part-I-2004) with bypass arrangement with ISI mark of reputed brand including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
44150mm dia nominal bore G.I.pipe having wall thickness 4.5mm electrical resistance welded of medium class confirming to IS- 1239(part-1/2004) with latest ammendments, screwed at both ends as per IS-554 with socketed at one end and the other end protected with plastic threaded protector including its transportation and unloading at L.I.P. site. The socket confirming to ISI 1239(part II/1992) with latest ammendments in random length of 4 to 7 mtr.Each pipe should bear IS certification and manufacturers name/trade mark complete as direction of Engineer-in-charge
45150mm dia G.I.Flange (Medium Duty) conforming to IS No-6392/1971 with ISI mark of reputed brand including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
46219mm dia M.S.Pipe (6.30mm thickness) IS 3589:2001 with ISI mark of reputed company including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
47Cost of 200mm MS/Steel slipon flange with ISI mark of reputed company including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
48Cost of 200 mm Ø PVC End Cap with ISI mark of reputed company including all cost, conveyance, cess etc completeas direction of Engineer-in-charge
49Cost of 200 mm PVC Equal Tee with ISI mark of reputed company including all cost, conveyance, cess etc completeas direction of Engineer-in-charge
50Cost, supplying of 50mm dia Kirloskar make C.I double Air Release Valve PN 1.6 with saddle and Raiser pipe conforming to IS 14845 (SI) with ISI mark including all cost, conveyance, cess etc complete as direction of Engineer-in-charge
51Cost of 100x100x25mm G.I. Tee with Plug for priming with ISI mark of reputed company including all cost, conveyance, cess etc completeas direction of Engineer-in-charge
52Cost of 160 mmx110 mm PVC/G.I./M.S. Reducer with ISI mark of reputed company including all cost, conveyance, cess etc completeas direction of Engineer-in-charge
53Cost of 200 mmx110 mm PVC/G.I./M.S. Reducer with ISI mark of reputed company including all cost, conveyance, cess etc completeas direction of Engineer-in-charge
54Cost of 200 mmx160 mm PVC/G.I./M.S. Reducer with ISI mark of reputed company including all cost, conveyance, cess etc completeas direction of Engineer-in-charge
55Labour Charges for Welding of 160mm/200mm GI/MS Pipe complete as direction of Engineer-in-charge
56Distribution Box with MCCB Alluminium Bus Bar for single bay with KIT KAT fuse for Substation Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58543499
AUTHORITY Government Departments
TENDER VALUE 77.37 Lakhs
LAST DATE 30-11-2026
Authority
Authority Name Orissa Lift Irrigation Corporation Limited
Work Description Tender for Installation And Energisation (Revival And Reinforcement) Of Jadapali-I,Ii, Badjore-Iv, Badteneda-I,Ii And Balipata-I,Ii,Iv Old Clips Under Tarabha Block (State Plan 2026-27)
Basic Detail
Tender No OLIC-SNP-04/2026-27
Bidding Type Tender
Location
City Sonepur
State Odisha
Key Dates
Publish Date 16 Nov 2026
Submission Date 30 Nov 2026
Open Date 01 Dec 2026
Finance
Tender Value 77.37 Lakhs
Tender Fee 11800
EMD 77373
Exemption Available
Document List
a590ccc7-e8fc-4014-b305-8f01b996716a.html
BOQ_620587.xls
Tendernotice_1.pdf
Tendernotice_2.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 16, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 30, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 11 days
Dec 01, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 12 days

Tender Documents

Download All (ZIP) ↓
html

a590ccc7-e8fc-4014-b305-8f01b996716a.html

xls

BOQ_620587.xls

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender