Tender For special Rep To Roof Treatment, Toilets And Certain Works At Bldg No P-94 Of Stn Hq Avadi Including special Rep To Bldg No T-10 And Its Allied Bldg Of Mh Avadi Under Ge Avadi For The Fy 2026-27
Tender Value
41.85 Lakhs
Estimated cost
Bid Submission
07 Dec 2026
20 days left
EMD
84000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thiruvallur → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Rep To Roof Treatment, Toilets And Certain Works At Bldg No P-94 Of Stn Hq Avadi Including special Rep To Bldg No T-10 And Its Allied Bldg Of Mh Avadi Under Ge Avadi For The Fy 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | PART - I - SPL REP TO ROOF TREATMENT, TOILETS AND CERTAIN WORKS AT BLDG NO P-94 OF STN HQ AVADI |
| 2 | Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and as directed by Engineer-in-charge. |
| 3 | Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by Engineer-in-charge. |
| 4 | Taking out shrubs / vegetation / tree growth from building at any height & any location and applying a Glyphosate pesticide or any other equivalent pesticide in a 10ml of solution with one litre of water on roots using spray gun including taking down cement plaster not exc 0.50 sqm for each tree and making good surface by plastering the same area with 20mm thick plastering in cement mortar 1:4 with WPC and finishing the surface to mathc existing surface with necessary scaffolding and other required T & P complete all as specified and directed by Engr-in- Charge. |
| 5 | Demolition of cement conctrete (un-reinfoeced) of any description and in any position not otherwise specifically provided complete all as specified and as directed by Engineer-in-charge. |
| 6 | M & L for 40mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) (Padding concrete) with water proofing compound and finished even and fair complete all as specified and as directed by Engineer in charge. Note : Supply only water proofing compound will be measured and paid separately. |
| 7 | M & L for screed bed of mortar 15 mm thick in cement mortar 1:4 for laying APP membrane and including mixing water proofing compound as per manufactureres instructions complete all as specified and directed by Engineer in charge.Note :- Water proofing compound shall be measured and paid for seperately under appropriate item of Sch \\"A' as supply only. |
| 8 | Supply only Liquid water proofing compound all as specified and directed by Engineer in charge. |
| 9 | M & L for brushing neat cement slurry with 3.0 kg of cement per square metre complete all as specified and directed by Engineer in charge. |
| 10 | M & L in repairs for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particles and applying one coat of bituminous primer @ 200 gms per sqm and then laying 3 mm thick APP modified bituminous membrane weighing not less than 3.50 kg/sqm reinforced weighing not less than 160 gms/sqm laid by torch application method overlap while torching shall be 75 mm on length and 100 mm width side, all angles & bituminous should sealed with extra care to ensure full bondage all joints and changes should covered with CM 1:3 with water proofing chemical as per manufacturer's instructions and cured well before laying membrane etc and applying aluminium paint @ 100 gram / sqm on roof or vertical surfaces complete all as specified and as directed by Engineer in charge. |
| 11 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and rubbish off the primises complete all as specified and as directed by Engineer in charge. |
| 12 | M & L for Geometric and 3D patterns tiles in vertical surface of 600x1200mm size and exc 10mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles and including rendering 10 mm thick in CM (1:4) on fair faces of brick work complete all as specified and as directed by Engineer in charge. |
| 13 | M & L for Joint free Non-Skid coloured ceramic tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes like tiles complete all as specified and as directed by Engineer in charge. |
| 14 | M & L for 40mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) cement concrete in sub base complete all as specified and as directed by Engineer in charge. |
| 15 | Demolition of precast concrete block walling and similar items i.e. ashlar facing dressing stone work, precast concrete articles etc of any description and in any position built in cement mortar including all quoins, arches and pillars etc. complete all as specified and as directed by Engineer in charge. |
| 16 | M & L for precast cement concrete block masonry with solid blocks exc 10 cm in width and set and jointed in C M 1:6 having ratio of PCC 1:3:6 type C1 (using 20mm graded stone aggregate as directed complete all as specified and as directed by Engineer in charge. |
| 17 | S & F in repairs of stainless steel kitchen plate rack size 750 x 600 x 250 mm & 0.63 mm thickness of grade AISI 304 incl suitable arrangements for hanging to wall complete all as specified and as directed by Engineer in charge. |
| 18 | Taking down of chowkhats / frames n exc 1.50 sqm each without taking off shutter each complete all as specified and as directed by Engineer in charge. |
| 19 | Taking down of chowkhats / frames exc 1.50 Sqm but n exc 4.0 sqm each without taking off shutter each complete all as specified and as directed. |
| 20 | M & L for forming Jambs etc to openings (to forgoings items) incl cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work in CM 1:6 complete all as specified and as directed |
| 21 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 22 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 23 | S&F anodised powder coated aluminium 3 track window shutters, ventilator fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, peg stays etc. complete all as specified & directed. |
| 24 | S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws, etc. complete all as specified & directed. |
| 25 | M & L for 12mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to aluminium frame work shutter.etc all as specified and as directed by Engr-in-charge |
| 26 | S&F aluminium (Die cast) body door closer hydraulically regulated designation No. 3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg & fixed complete all as specified & directed. |
| 27 | S & F in repairs mortice lock brass 4 levers vertical type with handle, size 100mm complete all as specified and as directed. |
| 28 | S & F of 5.5mm thick Sheet glass, ordinary quality and and glazing with oil putty in square n exc 0.5 sq. m in each pane and sheet glass is ground or obscured or frosted, on one side complete all as specified and as directed by Engineer in charge. |
| 29 | S & F of 5.5mm thick Sheet glass, ordinary quality and and glazing with oil putty in square exc 0.5 sq. m in each pane and sheet glass is ground or obscured or frosted, on one side complete all as specified and as directed by Engineer in charge. |
| 30 | S & F of 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed by Engineer in charge. |
| 31 | S & F of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer in charge. |
| 32 | Demolition of cement concrete ( un-reinforced) in ground floor and paving n.exc 15cm thickness below or above ground level complete all as specified. |
| 33 | M & L for plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate, 100mm thick as in sub base to floor complete all as specified and as directed |
| 34 | M & L for 100 mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in flooring, finishing the surfaces concrete topping even and fair without using extra cement complete all as specified and as directed |
| 35 | M & L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with Grade A sealing compound complete all as specified and as directed |
| 36 | Taking down cement plaster of any description from brick wall or concrete surfaces including racking out joints and hacking for key, scrubbing down with water etc complete all as specified and as directed by Engineer in charge. |
| 37 | M & L for 15 mm thick plaster in CM (1:6) on brick work / RCC concrete surfaces of wall and finish the surface even and smooth without using extra cement complete all as specified and as directed by Engineer in charge. |
| 38 | M & L for 5 mm thick plaster in CM (1:3) on brick work / RCC concrete surfaces of ceilings complete all as specified and as directed by Engineer in charge. |
| 39 | M & L for rendering 15 mm thick in CM 1:4 on concrete / fair surfaces of block masonary and including mixing water proofing compound as per manufactureres instructions and finished even and smooth without using extra cement complete all as specified and as directed by Engineer in charge.Note :- WPC shall be measured and paid for seperately. |
| 40 | M & L for preparation of newly plastered ceiling surfaces and applied three coats of white wash complete all as specified and as directed by Engineer in charge. |
| 41 | M & L for preparation of old plastered ceiling surfaces and applied one coats of white wash complete all as specified and as directed by Engineer in charge. |
| 42 | M & L for preparation of newly plastered wall surfaces and Providing and applying 3mm thick wall care putty on wall to prepare the surface even and smooth, including priming plastered and other surfaces with alkali resistant priming paint and Material and labour for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified and directed by Engr-in -Charge. |
| 43 | M & L for preparation of newly plastered wall surfaces and Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer in charge. |
| 44 | Complete removal of existing treatment on wall (any number of layers) by scarping with steel scrapers or any other mean and Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer in charge. |
| 45 | Complete removal of existing treatment on wall (any number of layers) by scarping with steel scrapers or any other mean including filling depressions of scrapped surface with putty and including priming plastered and other surfaces with alkali resistant priming paint and Material and labour for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified and directed by Engr-in -Charge. |
| 46 | Demoltion of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer in charge. |
| 47 | M & L for cement concrete type C-2, 1:3:6 (40mm graded aggregate), 75mm thick. as in plinth protection finished even and smooth without using extra cement including expansion joints complete all as specified and as directed by Engineer in charge. |
| 48 | Taking up or down steel tubing / CPVC Pipes and connection including cleaning for refixing or removed to store complete all as specified and as directed by Engineer in charge.(a) 16 mm bore dia |
| 49 | (b) 20 mm bore dia |
| 50 | (c) 25 mm bore dia |
| 51 | Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified & directed of following sizes :-(a) 16 mm outer dia |
| 52 | (b) 20 mm outer dia |
| 53 | (c) 25 mm outer dia |
| 54 | Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n, exc. 10cm girth complete all as specified and as directed by Engineer in charge. |
| 55 | S & F in repair Vitreous china premium/1st quality wash down water closet floor mounting/wall mounted EWC (One piece with flushing cistern) P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe PVC 32mm dia and incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, incl 100mm dia cast iron sanitary connections short connections pipe of length upto 600 mm and Cutting holes in or through walls, packing with PCC 1 : 2 :4 complete and taking down existing of any description/size complete in all respect all as specified. |
| 56 | S & F in repair Vitreous china premium/1st quality counter top wash basin, white, square or rectangular of size not less than 550x400x140 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including either top or bottom counter and cupboards/drawer type arrangements at ideal height from floor complete all as specified and as directed by Engineer-in charge |
| 57 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons,dados etc laid, bedded and pointed in any mortar and removal of rubbish off the site complete all as specified and as directed by Engineer in charge. |
| 58 | M & L for granite (of any colour) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform, counter for wash basin, flooring complete all as specified and as directed by Engineer in charge. |
| 59 | S&F in repair stainless steel Towel Rack with lower hanger size 24'' (600 mm) fixed to walls with hook Cera cat No F500110 complete all as specified and as directed by the Engineer-in-Charge. Make Jaquar/ Hindware/ Cera/ Prayag/ Parryware or equivalent as approved by Engr-In-Charge |
| 60 | S&F in repair Glass shelf size 600 mm long cera cat No F5001114 with and including bracket and glass complete set etc. complete all as specified and as directed by the Engineer-in-Charge. Make Jaquar/ Hindware/ Cera/ Prayag/ Parryware or equivalent as approved by Engr-In-Charge |
| 61 | S&F in repair corner glass shelf size 300 mm radius cera cat No F50051303 with and including bracket and glass complete set etc complete all as specified and as directed by the Engineer-in-Charge. Make Jaquar/ Hindware/ Cera/ Prayag/ Parryware or equivalent as approved by Engr-In-Charge |
| 62 | S & F in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer in charge. Make : Hindware F330043CP and equivalent |
| 63 | S & F in repair of two way bib cock chromium plated fancy type 15 mm bore with wall flange complete all as specified and as directed by Engineer in charge. Make : Hindware F740004CP and equivalent |
| 64 | S & F in repair 15 mm bore fancy type bib taps long body cast copper alloy chromium plated, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer in charge.. |
| 65 | S & F in repairs to health faucet with 1200 mm long flexible 32mm dia outlet pipe and having 184.5mm length of handle with wall hook complete all as specified and as directed by Engineer in charge. Make : Hindware F160023CP and equivalent |
| 66 | S & F in repairs 5 mm thick glass mirror with double coat for protection and longevity grounded edges for safety and silver plating on the back for better reflection mm thick of size of rectangle 900x700/800 x 600 mm bevelled edge mirror or rounded shape of selected quality glass with/without decorative PU frame vertical wall mounted with LED mirror with touch sensor and 3 light modes and fixed to walls using hidden studs complete all as specified and as directed by Engineer in charge. |
| 67 | S & F in repairs SS cockroach trap / nahani trap having size of 150mm x 150mm in sqaure shape SS 304 Grade glossy finish complete all as specified and as directed by Engineer in charge. |
| 68 | S & F in repairs SS floor drain having dia of 125mm in circular shape SS 304 Grade glossy finish with or without hole for waste pipe complete all as specified and as directed by Engineer in charge. |
| 69 | S & F in repairs PVC Waste pipe / outlet connector pipe 32mm dia / 40mm and length 1150mm and corrugated profile for fixing in WHB / Sink complete all as specified and as directed by Engineer in charge. |
| 70 | S & F of 25 mm bore ball brass valves, high pressure,with polythene float and flunut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by Engineer in charge. |
| 71 | S & F in repairs 25 mm bore dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer in charge. |
| 72 | Dismantling water tanks and removing to store Exc 500 litre & n exc 1000 litre amd Supply and fixing of 1000 litre capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed by Engineer in charge. |
| 73 | Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profiles reinforced with 19 x 19mm MS square tube provided with EPDM rubber gasket weather seal through out the frame and the profile mitre cut at two corners and joined by inserting 2 nos 150mm long brackets of 15 x 15mm MS square tube inside 19 x 19mm MS square tube suitably screwed complete all as specified and as directed by Engineer in charge. |
| 74 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification& drawing |
| 75 | S & F of aluminium anodised 200 mm barrel tower bolts of extruded section complete all as specified and as directed by Engineer in charge. |
| 76 | S & F of 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed by Engineer in charge. |
| 77 | S & F of 100 mm butt hinges extruded aluminium alloy with galvanized mild steel hinges pin anodised type `C'-22 complete all as specified and as directed by Engineer in charge. |
| 78 | S & F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter to dwarft wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engineer in charge. |
| 79 | S & F of 40mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engineer in charge. |
| 80 | S & F of stainless steel decorative curtain rod of 25 mm bore (weight not less 400 gms per running meter) incl fancy finial caps (02 nos in each curtain rod) etc complete all as specified and as directed by Engineer in charge. |
| 81 | S & F of Brass Chromium Plated designer Bracket for curtain rod of dia 25 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed by Engineer in charge. |
| 82 | S & F of factory made 18mm thick single extruded WPC (Wood Plastic composite) solid board of any colour, texture and pattern for cup board as in Kitchen cabinet and loft shutter, cupboard/drawer/shelf for countertop Washbasin and similar nature of work of required sizes comporising of virsin polymer of K Value 58-60 (Suspension grade), Calcium carbonate and natural fibres(wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density 650kg/cum and screw withdrawl strength of 1800N (Face) & 900 N (Edge) , minimum compressive strength 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water / moisture proof, and fire retardent complete all as per manufacturer instruction. |
| 83 | S & F of stainless steel Auto / Self closing concealed hinges 9.5 cranks for half overlay doors with opening angle 95* (14-32mm) with integrated overlay adjustment +_ 2.50mm & depth adjustment 4mm complete all as specified and as directed by Engineer in charge. Make : Godrej / Hettich. |
| 84 | S & F of round stainless steel cabinet knobs handlers dia of 27mm complete all as specified and as directed by Engineer in charge.complete all as specified and as directed by Engineer in charge. |
| 85 | S & F of floor door stopper of aluminium alloy body and tongue, anodised , with hard drawn steel spring overall length of cover plate 140 mm, complete all as specified and as directed by Engineer in charge. |
| 86 | Demolition and breaking up drain pipes upto 100/110 mm dia (Salt glazed ware, AC, PVC or reinforced concrete) set in cement mortar complete all as specified and as directed by Engineer in charge. |
| 87 | Demolition and breaking up drain pipes upto 75 mm dia (Salt glazed ware, AC, PVC or reinforced concrete) set in cement mortar complete all as specified and as directed by Engineer in charge. |
| 88 | Supply and fixing of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall/floor with suitable clamp complete all as specified and as directed by Engineer in charge. |
| 89 | Supply and fixing of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall/floor with suitable clamp complete all as specified and as directed by Engineer in charge. |
| 90 | Supply and fixing of PVC (SWR) bends any radius suitable for 110mm bore PVC pipes with access door complete all as specified and as directed by Engineer in charge.complete all as specified and as directed by Engineer in charge. |
| 91 | Supply and fixing of PVC (SWR) bends any radius suitable for 75mm bore PVC pipes with access door complete all as specified and as directed by Engineer in charge. |
| 92 | Supply and fixing of PVC (SWR) vent cowl for 110mm bore PVC pipes complete all as specified and as directed by Engineer in charge. |
| 93 | Supply and fixing of PVC (SWR) WC connector bent type for 110mm bore PVC pipes complete all as specified and as directed by Engineer in charge |
| 94 | Supply and fixing of PVC (SWR) for 75mm Diameter of outlet floor trap, plain with grating including jointing with solvent cement etc complete all as specified and as directed by Engineer in charge. |
| 95 | Supply and fixing of PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed by Engineer in charge. |
| 96 | S&F for Sensor type urinal of size 29.5x32.5x57.5cm Make: Hindware |
| 97 | S&F for Sensor type pillar taps Make: Hindware |
| 98 | S & F in repair Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. |
| 99 | Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete al as specified and directed. |
| 100 | S & F hollow PVC Wall Lining consisting of 6mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all respect including supply and fixing of all accessories like fasteners/screws/solvent etc all as recommended by manufacturer all as specified (colour/pattern as approved by Accepting Officer). |
| 101 | Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. Wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) |
| 102 | M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed |
| 103 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 104 | M & L for cornice work at the plaster of paris ceiling for the required design approved by Engineer-in-charge complete all as specified and as directed |
| 105 | M& L for two coat of Oil bound distemper on ceiling surface including prepration of new surface all as specified and directed . |
| 106 | Taking down carefully unserviceable point wiring copper / aluminium (light, fan, socket or power) complete, including removal of batten / conduit / gutties / wooden board etc., including fittings and fixtures such as switches, ceiling roses, regulators, sockets, light fittings, fans etc., removal from site under Sch of credit and removal of unserviceable items out of site and making good the disturbed surfaces of walls, ceilings etc., complete all as specified and as directed. |
| 107 | Point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated FRLSH ,1100 volts grade unsheathed cable confirming to IS-694, 1977 with multistranded copper conductor, drawn through and including non-metalic rigid PVC conduit, conduit fittings and conduit accessories not less than 20 mm dia concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc., and including provision of one 1.5 sqmm PVC insulated single core multistranded copper conductor FRLSH green in colour as earth continuity conductor and connected to common earth dolly,including Modular boxes, frames and cover plates all as specified for the following:(a) One light point controlled by one switch. |
| 108 | (b) One Ceiling fan point controlled by one switch and regulator |
| 109 | (c) One Exhaust fan point controlled by one switch. |
| 110 | (d) One 3 pin 5 amps socket point on same board |
| 111 | (e) One 3 pin 5 amps socket point on independent board |
| 112 | M & L for point wiring with two runs of 4 Sqmm (nominal area) PVC insulated,FRLSH sheathed, multistrand, 1100 volts grade copper conductor cable single core, drawn through with and including non metallic PVC conduit 20/25mm dia and its accessories fixing on wall/ceiling/ trusses with suitable clamps , screws etc including one run of 4 Sqmm PVC insulated single core multistranded copper conductor FRLSH green in colour as earth continuity conductor and connected to common earth dolly,including Modular boxes, frames and cover plates all as specified for One 5 pin 5/15 amps socket point on independent board complete all as specified. |
| 113 | Taking down carefully unserviceable Power / Sub main wirings with PVC aluminum conductor cables in PVC/STEEL conduits / TW battens up to 2 runs of 6 Sq.mm removing materials from site, taken as credit , making good the disturbed surfaces all as specified and as directed. |
| 114 | Point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated FRLSH ,1100 volts grade unsheathed cable confirming to IS-694, 1977 with multistranded copper conductor, drawn through and including non-metalic rigid PVC con |
| 115 | M&L for wiring for circuit / power /sub main wire with two runs of single core 6 Sqmm size and one run of 6 Sqmm (green colour as earth continuity conductor) PVC insulated, sheathed, multi stranded copper conductor FRLSH cable drawn through including suitable dia PVC conduit concealed in wall and fixing arrangement on ceiling/trusses with suitable clamps,screws etc complete with accessories all as specified. |
| 116 | Supply and Fixing Modular switch 1 way 6A, 1 module complete all as specified. |
| 117 | Supply and Fixing Modular switch 1 way16A, 1 module complete all as specified. |
| 118 | Supply and Fixing Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified. |
| 119 | Supply and Fixing Modular Socket, 6A/16A - 2/3 pin combined 2 module complete all as specified. |
| 120 | S&F ceiling rose 65 X 50 mm , three terminals ,bakelite , surface complete all specified. |
| 121 | S&F in replacement of Single Pole Neutral Enclosure with a Two pin and Earth plug and socket complete with one single pole MCB 20A complete all as specified and directed.(For Acs) |
| 122 | Taking down existing unserviceable MCB's/MCCB's/DBs any capacity complete all as specified & directed by Engr in charge. |
| 123 | Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified.(MCB for SPN DB) |
| 124 | Supply and fixing 240V, 30 mA double pole RCBO, cap 40Amp/ 63 Amp, in the MCB DB Complete with connection testing and commissioning complete all as specified. |
| 125 | Supply and fixing in replacement of LED tube light fitting with polycarbonate LED tube light 20W 4 feet and 1 x 20 watt box type batten aluminum body with microwave motion technology and integrated electronic driver including rotary type bipin holder and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed. |
| 126 | S&F Surface and wall mounted LED tube light fitting 2 Feet long, 10 W, batten type, PC housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with all accessories , suitable for operation on AC, single phase 220 / 230 Volts , 50 Hz supply, and including connecting up with PVC sheathed suitable copper conductor flexible wire from ceiling rose to fitting complete all as specified and as directed. |
| 127 | S&F LED Panel light recessed 30/32 watt (2 x2 ),white powder coated CRCA full glow recess mounting LED Backlit Panel, integrated electronic driver complete including connection from ceiling rose to light fitting with twin core cable 23/0.0076 Sqmm complete all as directed. |
| 128 | Taking down the old unsv BER Exhaust Fan and deposit in MES store yard with down rods complete all as specified and as directed. |
| 129 | Supply and Fixing Modular fan step regulator , 120w, 2 module complete all as specified. |
| 130 | Supply and fixing Single phase propeller type Exhaust fan heavy duty AC 230 volts 300 mm sweep, metallic body complete with louvrers and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed. |
| 131 | Earthing complete with galvanised iron earth plate electrode 600mm X 600mm X 6mm thick, with and including earthing of 4mm dia GI wire protected by 15mm dia GI pipe light grade upto a length of 7.5m. The plate shall be buried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of the earth plate at a depth not less than 1.5 metres below ground level, connected to earth lead as described here-in-before by means of bolts, nuts, washers and checknuts made out of galvanised iron or mild steel, earthing lead protected by as described here-in-before and connected to main switch board or main control board or electric pole all as shown on electrical plate No.3 of MES Sch Part-I including necessary earth work and excavation in any type of soil, plain cement concrete 1:3:6, type C1 chamber, reinforced cement concrete cover slab with locking arrangement and handle of 10mm dia MS round bars 450mm long, 1:2:4 type B1, 50mm thick with 8mm dia TMT bars at 140mm centre to centre both ways, GI pipe of bore 20mm medium grade for watering with funnel, wiremesh, salt, charcoal, lugs including testing complete all as specified and as directed. |
| 132 | Material and labour for GI earth continuity conductor or main earthing lead fixed to valve on batten or recess or chases or burried in ground or drawing in conduit or any other situation for loop earthing etc as reqd 4 mm dia galvanized steel wire all as specified and directed by Engr-in-Charge |
| 133 | PART - II - SPL REP TO BLDG NO T-10 AND ITS ALLIED BLDG OF MH AVADI |
| 134 | Dismantling plain /corrugated steel sheeting any gauge, any thickness in roof covering, valley gutters or wall cladding etc complete all as specified and as directed by Engineer in charge. |
| 135 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed wih self tapping screws complete all as specified and as directed by Engineer in charge. |
| 136 | S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet in ridges, hips, valley gutters of 0.50mm thick of any colour having tensile strength of 550 Mpa as in, fixed with self tapping screws complete all as specified and as directed by Engineer in charge. |
| 137 | Dismantling of ceiling board of any thickness. Including frame work all as specified and as directed by Engineer in charge |
| 138 | M&L for aluminium snap and false ceiling of panels of size 600 x 600 mm using aliminium anodised wall angle of size 25 x 25 x 1.5 mm thick fixed to walls with rawl plug and screws n exc 1.50m centre to centre and intermidiate panels using main \\"Tee\\" and cross \\"Tee\\"aluminium anodised section of size 35 x 25 x 1.50 mm and 25 x 25 x 1.50mm thick suspended with and including 2mm dia GI wire n exc 1.2 m centre to centre including PVC coated gypsum ceiling tiles of any description, not otherwise, described, over 10cm width or girth complete all as specified and as directed.. |
| 139 | Dismantling wrought iron work or mild steel of any description not otherwise provided for truss/purlin/rafter etc complete all as specified and as directed |
| 140 | S&F Roof trusses (framed) Fe-410w (Gde E-250) quality - 'A' , trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed |
| 141 | S&F Rolled sections Fe-410W (Gde E-250) quality A as in main and cross beams, hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or other connecting plates complete all as specified. |
| 142 | M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 143 | S&F of Stainless steel Turbo ventilator with stainless steel base fixed with galvalume sheet at the roof complete all as specified and as directed |
| 144 | S&F 2 mm thick clear embossed/opal white polycarbonate sheet with UV stabliser having atleast 60-80% transparancy as per relevant IS including fixing side and lapse with seal cover complete all as specified and as directed |
| 145 | Taking down chowkats or frame exc. 1.50 sqm but nexc 4.00 sqm each with shutter (without taking of shutter from the frame) complete all as specified and as directed by Engr-in-Charge. |
| 146 | Taking down Chowkhats or frames not exc 1.5 sqm each but with shutters (without taking off shutters from the frames) complete all as specified and as directed by Engr-in-Charge. |
| 147 | M & L for forming Jambs etc to openings (to forgoings items) incl cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work in CM 1:6 complete all as specified and as directed |
| 148 | M&L for preparation of newly plastered jambs surface and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified. |
| 149 | S & F anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. |
| 150 | S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws, etc. complete all as specified & directed. |
| 151 | M & L for 9mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to aluminium frame work shutter.etc all as specified and as directed by Engr-in-charge |
| 152 | S&F aluminium (Die cast) body door closer hydraulically regulated designation No. 3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg & fixed complete all as specified & directed. |
| 153 | S&F anodised powder coated aluminium 3 track window shutters, ventilator fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, peg stays etc. complete all as specified & directed. |
| 154 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge complete all as specified and directed. |
| 155 | S&F for 4.0 mm thick figured glass pin headed type and glazing with oil putty in squares exc 0.5 sqm in each pane complete all as specified and as directed. |
| 156 | S&F for 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane complete all as specified and as directed |
| 157 | S&F aluminium rebated mortice lock vertical type size 100mm four lever complete all as specified & directed. |
| 158 | S&F floor door stopper 150mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and as directed. |
| 159 | S&F in repair for Harrison Curtain rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.in repair all as specified and as directed by Engr-in-charge |
| 160 | Demolition of Brickwork of stone/boulder masonry, build incement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 161 | M&L Brickwork with fly ash Old size bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed |
| 162 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc all as specified and directed |
| 163 | M&L Rendering 15mm thick in two layers (i.e 5mm thick CM in 1:4 with WPC over 10mm thick CM 1:6) on other than fair faces of brick work or stone masonry surfaces, even and smooth (without using extra cement), complete all as specified and directed by Engineer-in charge. Note:- WPC will be measured and paid seperately. |
| 164 | Supply only integral water proofing compound (ISI marked) all as specified and directed by Engineer-in charge. |
| 165 | M & L for Rendering 10 mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces, finished even and smooth, without using extra cement complete all as specified and as directed by Engineer-in charge. |
| 166 | Demolition of cement concrete (unreinforced) in ground floor or pavings n exc 15 cm thickness (below or above ground level) all as specified and directed by Engineer-in charge |
| 167 | Dismantling floor, hearth or wall tiling including cement mortar bedding,(but not backing) and rubbish off the premises complete all as specified and as directed by Engineer-in charge. |
| 168 | M & L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm/ 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles and including rendering 10 mm thick in CM (1:4) on fair faces of brick work complete all as specified and as directed by Engineer in charge. |
| 169 | Dismantling of stone slab and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed by Engineer-in charge. |
| 170 | M & L for 100 mm thick plain cement concrete 1:5:10 type E2 using 40mm graded stone aggregate, as in sub base complete all as specified and as directed by Engineer-in charge |
| 171 | M&L for chequred cement concrete tiles mixed with grey cement and no pigment of size 300x 300 x25 mm thick set jointed and pointed in neat cement slurry in floors incl 20 mm thick screed in CM 1:4 complete all as specified and as directed by Engineer-in charge |
| 172 | M & L for granite (of any colour) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform, counter for wash basin, flooring and all other similar works and 15mm thick screed bed mortar in CM 1:4 complete all as specified and as directed by Engineer in charge. |
| 173 | M & L for Machine cut kota stone slab flooring 20-25mm thick ini flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15mm thick screed bed mortar in CM 1:4 complete all as specified and as directed by Engineer in charge. |
| 174 | M & L for 40mm thick Cement concrete type B-1,1:2:4 (20mm graded aggregate) for flooring finished even and smooth without using extra cement complete all as specified and as directed |
| 175 | M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection surfaces finished even and fair without using extra cement, complete all as specified and as directed. |
| 176 | M & L for preparation of newly plastered wall surfaces and Providing and applying 3mm thick wall care putty on wall to prepare the surface even and smooth, including priming plastered and other surfaces with alkali resistant priming paint and Material and labour for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified and directed by Engr-in -Charge. |
| 177 | M & L for preparation of newly plastered wall surfaces and Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer in charge. |
| 178 | Material and labour for preparation of old painted surfaces of steel and iron of any description over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed. |
| 179 | S & F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement morter to dwarft wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engineer in charge. |
| 180 | Taking up or down steel tubing / CPVC Pipes and connection including cleaning for refixing or removed to store complete all as specified and as directed by Engineer in charge.(a) 16 mm bore dia |
| 181 | (b) 20 mm bore dia |
| 182 | (b) 25 mm bore dia |
| 183 | Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified & directed of following sizes :-(a) 16 mm outer dia |
| 184 | (b) 20 mm outer dia |
| 185 | (c) 25 mm outer dia |
| 186 | S & F in repairs Vitreous China Wash basins, white, flat back, size 630x450mm, including cutting for and pinning in ends of brackets or erecting stand but inclusive of supply and fixing of waste couplings and waste pipe complete all as specified and as directed by Engineer in charge. |
| 187 | S & F in repair PVC connection 15mm size PTMT nuts of length 450 mm complete all as specified and as directed by Engineer in charge.. |
| 188 | S & F in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer in charge. |
| 189 | S & F in repair of two way bib cock chromium plated fancy type 15 mm bore with wall flange complete all as specified and as directed by Engineer in charge. |
| 190 | S & F in repair fancy type CP pillar tap with capstan heads, spindles and washer plates cofirm to IS 1795 having mark 'Cold' or 'Hot' and weight not less than 0.65 Kg complete all as specified and as directed by Engineer in charge. |
| 191 | S & F in repair 15 mm bore fancy type bib taps long body cast copper alloy chromium plated, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer in charge.. |
| 192 | S & F in repairs SS cockroach trap / nahani trap having size of 150mm x 150mm in sqaure shape SS 304 Grade glossy finish complete all as specified and as directed by Engineer in charge. |
| 193 | S & F in repairs SS floor drain having dia of 125mm in circular shape SS 304 Grade glossy finish with or without hole for waste pipe complete all as specified and as directed by Engineer in charge. |
| 194 | S & F of 25 mm bore ball brass valves,high pressure,with polythene float and flunut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by Engineer in charge. |
| 195 | S & F in repairs 25 mm bore dia gun-metal,globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer in charge. |
| 196 | Dismantling water tanks and removing to store Exc 500 litre & n exc 1000 litre amd Supply and fixing of 1000 litre capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed by Engineer in charge. |
| 197 | S&F in repairs 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on PVC moulding and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified. |
| 198 | Material and labour for rendering 10mm thick in cement mortar 1:6 on fair faces of brick/concrete on external surfaces finished all as specified and as directed. |
| 199 | S& F TMT Bars 10mm dia & over cut length bent to shape required including mild steel wire (anneled) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 200 | M&L for precast cement concrete in (1:2:4) type B1 (using 20mm graded stone aggregate) set in cement mortar 1:6 as in landings, cover slabs, water troughs, mangers, shelves, supporting slabs and similar articles with plain face including necessary form work complete all as directed. |
| 201 | Taking down carefully unserviceable point wiring copper / aluminium (light, fan, socket or power) complete, including removal of batten / conduit / gutties / wooden board etc., including fittings and fixtures such as switches, ceiling roses, regulators, sockets, light fittings, fans etc., removal from site under Sch of credit and removal of unserviceable items out of site and making good the disturbed surfaces of walls, ceilings etc., complete all as specified and as directed. |
| 202 | M&L for Point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated FRLSH unsheathed multistrand ,1100 volts grade copper conductor cable,single core, drawn through with and including non-metalic rigid PVC conduit 25mm dia,and its accessories concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc., and including provision of one 1.5 sqmm PVC insulated single core multistranded copper conductor green in colour for continuous earthing, 1.6mmthk MS terminal box finished to wall with 3mm thk laminated hylam sheet top cover all as specified for the following:(a) One light point controlled by one switch. |
| 203 | (b) One Ceiling fan/Exhaust fan point controlled by one switch. |
| 204 | (c) One 3 pin 5 amps socket point on same board |
| 205 | (d) One 3 pin 5 amps socket point on independent board |
| 206 | M & L for point wiring with two runs of 4 Sqmm (nominal area) PVC insulated,FRLSH sheathed, multistrand, 1100 volts grade copper conductor cable single core, drawn through with and including non metallic PVC conduit 20/25mm dia and its accessories fixing on wall/ceiling/trusses with suitable clamps , screws etc including one run of 4 Sqmm PVC insulated copper conductor cable green in colour for continuous earthing, 1.6 mm thick MS terminal box finished to wall with 3 mm thick laminated hylam sheet top cover all as specified for One 5 pin 5/15 amps socket point on independent board complete all as specified. |
| 207 | Supply and Fixing switch Piano flush type, single pole, 5Amps complete all as specified. |
| 208 | S&F switch socket 3pin 5 Amps, multi pin flush type complete all as specified. |
| 209 | S&F switch socket 2 in 1, 3pin 5 and 15 Amps,flush type completewith MS terminal box and laminated hylam sheet with accessories all as specified. |
| 210 | Supply and fix stepped type elctronic fan regulator, flush type phenolic laminated sheet etc complete all as specified. |
| 211 | S&F ceiling rose 65 X 50 mm , three terminals ,bakelite , surface complete all specified. |
| 212 | S&F of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete as specified. |
| 213 | Taking down carefully unserviceable Power / Sub main wirings with PVC aluminum conductor cables in PVC/STEEL conduits / TW battens up to 2 runs of 6 Sq.mm removing materials from site, taken as credit , making good the disturbed surfaces all as specified and as directed. |
| 214 | M&L for wiring for circuit / power /sub main wire with two runs of single core 6 Sqmm size and one run of 6 Sqmm (green colour as earth continuity conductor) PVC insulated, unsheathed, multi stranded copper conductor FRLSH cable drawn through including suitable dia PVC conduit concealed in wall and fixing arrangement on ceiling/trusses with suitable clamps,screws etc complete with accessories all as specified. |
| 215 | S&F Load line vertical distribution Board, TPN 8 way double door, fixed on wall semi flush, loadline DB are fitted with Bus bars, neutral links, blanking plates, including incommer MCCB 100/125 Amps,TP and suitable outgoing MCB 40 /63Amps,SP/DP/TPN with all accessories suitable for DB including taking down old unserviceable DB all as specified and as directed. Note : Incoming MCCB and Out going MCBs measured seperately relevent items. |
| 216 | S&F MCB DB SPN 12 way, double door, powder coated, 240 volts, AC, 50Hz, IP 43 protected, with provision for MCB double pole as incomer and SP MCBs as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming and Outgoing MCB measured separately relevent items. |
| 217 | Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified.(MCB for SPN DB) |
| 218 | Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole Neutral and current carrying capacity 32-63 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified.(MCB for VTPN DB) |
| 219 | Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of TP and current carrying capacity 16-32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified.(MCB for VTPN DB) |
| 220 | Supply and fixing MCCB 3 Pole, 415 V, FP, 100 Amps with breaking capacity 16 KA complete all as specified. |
| 221 | Supply and fixing in replacement of LED tube light fitting with polycarbonate LED tube rod 20W 4 feet and 1 x 20 watt box type batten aluminum body with microwave motion technology and integrated electronic driver including rotary type bipin holder and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed. |
| 222 | S&F LED Panel light recessed 30/32 watt (2x2) white powder coated full glow recess mounting LED Backlit Panel, integrsted electronic driver complete including connection from ceiling rose to fitting complete all as specified and as directed. |
| 223 | S&F LED building security light fitting 45W made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07, complete pre-wired and connecting up with suitable twin core flexble copper wire including provision of necessary GI tubing medium grade 25mm bore of pipe 1.5 bent to shape with necessary clamps made out of mild steel, nuts and bolts etc., including two coats of synthetic enamel paint over a coat of red oxide primer on exposed steel surface for fixing the fitting to Bldg etc complete all as specified and as directed. |
| 224 | Supply and fix Exhaust fans AC Single phase 230/240V of size 300mm sweep with louver complete all as specified and directed. |
| 225 | Supply and fix Exhaust fans AC Single phase 230/240V of size 450mm sweep with louver complete all as specified and directed. |
| 226 | Material and labour for earth continuity conductor or main earthing lead fixed to valve on batten or recess or chases or burried in ground or drawing in conduit or any other situation for loop earthing etc as reqd 4 mm dia galvanized steel wire all as specified and directed by Engr-in-Charge |
| 227 | Earthing complete with galvanised iron earth plate electrode 600mm X 600mm X 6mm thick, with and including earthing of 4mm dia GI wire protected by 15mm dia GI pipe light grade upto a length of 7.5m. The plate shall be buried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of the earth plate at a depth not less than 1.5 metres below ground level, connected to earth lead as described here-in-before by means of bolts, nuts, washers and checknuts made out of galvanised iron or mild steel, earthing lead protected by as described here-in-before and connected to main switch board or main control board or electric pole all as shown on electrical plate No.3 of MES Sch Part-I including necessary earth work and excavation in any type of soil, plain cement concrete 1:3:6, type C1 chamber, reinforced cement concrete cover slab with locking arrangement and handle of 10mm dia MS round bars 450mm long, 1:2:4 type B1, 50mm thick with 8mm dia TMT bars at 140mm centre to centre both ways, GI pipe of bore 20mm medium grade for watering with funnel, wiremesh, salt, charcoal, lugs including testing complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysDec 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender