Water Resources and Irrigation Government Departments Closing in 11 days TDR #58541634

Tender For Installation Of Badmal-Iii L.I. Projects Under Maneswar Block In Sambalpur District Of L.I. Division, Sambalpur

Issued by Government Departments · Sambalpur, Odisha
Tender Value
61.36 Lakhs
Estimated cost
Bid Submission
30 Nov 2026
11 days left
EMD
61365
Bank guarantee accepted
Document Fee
11800
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Sambalpur → Odisha
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Installation Of Badmal-Iii L.I. Projects Under Maneswar Block In Sambalpur District Of L.I. Division, Sambalpur

BOQ

Name of Work:- Installation of Badmal-III L.I. Projects under Maneswar Block in Sambalpur District of L.I. Division, Sambalpur
Sl. No. Item Description
1Part-A
2Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-in-charge.
3Excavation in hard soil such as Hard stiff clay, stiff black cotton, hard red earth, shales, moorum ordinary gravels, within 50m. Initial lead and 1.5m. Initial lift including rough dressing and breaking clods and stacking rubble or spreading and leveling within the site as the case may be etc; complete.asper direction of the Engineer-in-charge.(Mechanical 60% & Manual 40%)
4Filling in F&P with excavated materials including well watered and rammed.in hard soil such as Hard stiff clay, stiff black cotton, hard red earth, shales, moorum ordinary gravels, within 50m. Initial lead and 1.5m. Initial lift including rough dressing and breaking clods and stacking rubble or spreading and leveling within the site as the case may be etc; complete.asper direction of the Engineer-in-charge.(Mechanical plus manual )
5Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge.
6Cement concrete (1:4:8) with 4cm size h.g.b. crusher broken metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc. complete as per the direction of the Engineer-incharge.
7Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6)in foundation & plinth complete as per the Engineer-incharge
8Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) in super structure etc. complete as per the Engineer-incharge
9Cement concrete (1:2:4) with 12mm size black h.g.b. crusher broken chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge.
10Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-inchargeRoof slab, chajja, carnice etc
11Lintel
12Plinth band, foundation, footing base of column etc
13Beams & Columns
14Walla & fins
15Labour charges for MS reinforcement for RCC work including cutting, bending & tying the grills and placing in position including cost of binding wire 18 to 20 gauge & HYSD steel bar ( FE 415/ FE 500 )
16R.C.C. work in C.C. (1:2:4) including hoisting & laying & curring for 28days using 12mm. Size clean black hard granite crusher broken chips of approve quality and from approve quarry including cost taxes conveyance charges of all materials to the worksite with supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
1712mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
18Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge.
19Dry brick rammed Khoa (10 cm) thick well watered and rammed.
2025mm thick AS flooring with CC (1:2:4) using 12mm sizeblack h.g.c.b chips of approved quality from approved quarry including watering and curing with cost, taxes, royality and conveyance charges of all materials to the work site and supply of all labour, T & P required for the work etc. complete
212.5 cm thick grading concrete (1:2:2) with 6 cm size h.g chips
22Cement washing two coats over plastering
23Finishing walls with plastic emulsion paint of approved shade on new work two coat to give an even shade excluding cost of paint.
24Wall painting two coats with weather coat paint of approved shade excluding cost of paint.
25Cost of plastic emulsion paint
26Cost of weather coat cement paint
27Painting of red oxide primer of approved quality for priming over iron work including cost, taxes etc. complete
28Painting of enamel paint of approved quality and colour for painting over iron work including cost, taxes etc. complete
29MS panel door double leafed with MS frame overall size of 1.20x1.98 mtr for door and 0.90x0.90 mtr for window, shutter of 20 gauge CR sheet panel as per approved size and specification etc. including fitting & fixing the door etc. complete
30Supplying all materials, labour, T&P for jointing of 250 mm outer dia High Density Polythylene Pipes of specified material grade & pressure rating by butt fusion welding method as per speciication & laying in tranches including testing including all cost etc complete as per direction of the Engineer-in-charge
31Supplying all materials, labour, T&P for jointing of 200 mm outer dia High Density Polythylene Pipes of specified material grade & pressure rating by butt fusion welding method as per speciication & laying in tranches including testing including all cost etc complete as per direction of the Engineer-in-charge
32Supplying of 200 mm dia PN - 6 PE - 80 HDPE Pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation to work site in complete shape
33Supplying of 250 mm dia PN - 4 PE - 80 HDPE Pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation to work site in complete shape
34Filling the foundation and plinth with excavated material as directed by the Engineer-incharge. A) Hard Soil
35Supplying & fitting of RCC ventilators
36entrifugal monoblock pumpset total head of 28 mtr capable to discharge 1700 LPM with 15 HP/11 KW squirrel cage induction motor fitted with bronze impeller TB-2 of iS 318/1981, companion flanges & class 'F' insulation suitable for operation 415 volt + 6% - 15%, 3 phasde, 50 Hz aC power supply, delivery = 100x100 mm with BEE star rated energy efficiency pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership network for easy availibility of spares
37Control panel with automatic star delta starter sheet steel enclosure vsuitable for operation of squirrel cage induction motor up to 15 HP with 16 Amp.(AC-3) duty contractor at 415 volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & No volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The starter should provide dependable protection against over load and single phasing fitted with Volt meter, Ammeter, MCB in complete shape including indicator lamp
38Cost of 63 Amp -400 V.T.P. Main Switch confirming to IS No.4064
39Cost of panel board made out of 18 gauge CR sheet
404 KVAR Capacitor
41Motor Hood (size 0.45x0.45x0.60 mtr ) made with 18 SWG cold rolled mS sheet with one coat of red oxide primer and two coats of smoke gray / navy blue enamel paint both side (inside & outside) suitable to cover centrifugal monoblock Pump set from 10 to 15 HP and having provision for attachment with the groves on rear side of the panel board
42Base Plate made of MS Channel with holes for Motor & Panel
433 x 16 mm² Tarpedore cable XLPE ( cross link polyethylin ) confirming to IS: 7098 (Part-II) including laying below 0.90 mtr of the ground and filling the excavated materials including watering and ramming
447/20 P.V.C. Wire
45100 mm dia nominal bore GI pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt - 1 of 2004) with socketed at one end and the other end protected with plastic thread protector. The socket confirming to IS - 1239 (pt - II / 1992) with latest amendments in random length of 4 to 7 mtrs. Each pipe should bear ISI certification & manufacturer's name/ trademark
46100 mm dia GI Bend IS No. 1239(pt-II/1992)
47100 mm dia GI flange IS No. 6392 / 1971
48100x100x25 mm GI Tee with plug for priming
49100mm C.I. Foot Valve should be of swing type friction less with single disc confirming to iS - 4038/1979 of reputed brand
50100mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement
51250mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement
52200 mm dia Butterfly valve as per IS - specification
5350 mm dia CI AR valve with saddle and riser pipe confirming to IS 14845 with ISI mark
54250x250x200 mm dia spigot moulded reducing HDPE Tee 10 kg
55250 mm dia HDPE Elbow spigot design 6 kg
56250 x200 mm HDPE Reducer
57250 mm dia HDPE end cap
58200 mm dia HDPE end cap
59200x200x110 mm HDPE/GI Raiser tee set with bend closing and opening arrangement
60250 mm dia HDPE Tail piece 160 mm long
61250 mm dis MS pipe (Medium Duty ) 5.4 mm thick
62250 MM Dia MS Flange
63Construction of out let for Tee Tank
64Supply of small T & P Kit comprising of hand gloves - 1 pair, tester - 1 no, 8\\" cutting plier - 1 no, 12\\" sly wrench - 1 no, 12\\" screw driver - 1 no, 24/27 & 21/23 DE spanner - 2 nos, 24/27 & 21/23 Ring spanner - 2 nos of Taparia make
65Labour charges for installation of 20 HP openwell submersible Motors including transportation from village to work site, fitting & fixing of base frame, fitting & fixing suction and delivery pipe to motor, other fitting materials including cutting, welding etc. complete as per the direction of the Engineer-incharge.
66Cost of Rubber Insertion and nut Bolt etc.
67Labour charges for delivery and fitting including fitting of priming Tee, sluice Valve, NR Valve, air release valve and riser Tee etc and installation
68Cost of river embankment cutting, cleaning ; fitting of suction & delivery fittings with flanges, bend, foot valve, sluice valve, NR valve etc including cost 1/8\\" rubber insertion, Nut nolt, white lead paint etc vomplete
69Welding at site including supply of Welding machine, Generator set, all labour, materials and T & P
70Part-B
71Construction of 3 phase 3 wire 11 KV HT line as per REC standard confirming to RE Rules 1956 excluding 400 Kg. 10 Mtr. Long PSC pole support in 50 Mtr. Span.55sqmm Insulated covered AAA Conductor (190 kg/km) for elephant corridor area with double disc arrangement,11KV \\"V\\" cross arm with required nos. of 11 KV B & S disc. Insulators(120 KN) and 11KV pin insulators(70 KN), Padding & concreting of poles(1.5'X2'X3'),danger board at each pole, anticlimbing devices.Stay set at each bending point and double stay at end point with 18mm G.I. H.T. stay, concreting of stay with anchor plate etc. including cost of materials, labour, transportation, inspection & commissioning etc. complete including painting in Navy Blue colour band with inscription of OLIC in each Pole as per direction of Engineer-in-Charge.
72Construction & erection of 11/0.416 KV, 63 KVA (BIS level-II star 2) D.P mounted Sub-Station including transformer confirming to RE Rules,1956 mounted on 2.8 Mtr. Long structure, excluding 400 Kg. 10 Mtr. Long PSC pole,transformer mounting channel & top channel made 0f 2.8 Mtr. Long 100x50x6 mm M.S. channel, transformer belting on 2.8 Mtr. long 50 x 50 x 5 mm M.S. Angle(all REC.SPN. Std.F-3) with all accessories like 3 pole 11 KV HG Fuse (F-5) & A.B.Switches(400 Amp with ball bearing) (F-9) both mounted on 2.8M long 75x40x6 mm M.S. Channel and supported by 1.0 mtr. long 50x50x5 mm M.S. Angle with 3 nos. 11 KV lightening Arrestors and Distribution box for 63 KVA S/S, including cost of 35 sqmm 3.5 Core PVC cable carping & padding of Poles, Danger board at each Pole, Anti Climbing Devices & all other necessary fittings. 05 nos FI Pipe Earthing 40 Dia Medium gage 3 mtrs in no 04 G.I wire and 01 no G.I Flat Earthing for Neutral along with L.T.Distribution box including 100 Amps Kit Kat fuse with MCCB (As per DISTCOM specification). Long,fixing of stay set with 0.5 Cum cement concret foundation 1:3:6 of required size , 3 1/2 x 35 sqmm. PVC Cable , , Bolts, Brackets, Cable sockets etc. including cost of all materials, labour, transportation complete with liasioning for testing, inspection and commissioning including painting in Navy Blue colour band with inscription of OLIC in each Pole as per direction of Engineer-in-Charge.
7310 mtr 400 kg PSC pole for HT line (in elephant corridor area).
74Boundry wall of Sub-Station (size 15' x 10') with Sand filling and metal spreading, Fixing of Iron gril gate of double doors of 01 mt each to be fixed in proper size of briks. The gate is to be painted with silver coloured enamel paints and lock & key arrangements to be provided etc. as per the direction of the site engineer-in-charge.
75Spike provisin on 10 mt long 400 kg PSC pole for elephant corridor area as per the direction of the site engineer-in-charge.
76Electrical Pipe Earthing for Motor and Panel box of 40 mm dia Medium gage 3 mtrs using required quantity of common salt, charcoal , GI nut bolt including digging the earth pit of size 1.2mtr. X 1.2mtr.x3mtr. And digging the wire trench and refilling after completion of earthing including supply of all materials trnsportation etc. complete as per the direction of the site engineer-in-charge.
77Internal wiring for Pump house as per instruction the direction of the site engineer-in-charge. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58541634
AUTHORITY Government Departments
TENDER VALUE 61.36 Lakhs
LAST DATE 30-11-2026
Authority
Authority Name Orissa Lift Irrigation Corporation Limited
Work Description Tender for Installation Of Badmal-Iii L.I. Projects Under Maneswar Block In Sambalpur District Of L.I. Division, Sambalpur
Basic Detail
Tender No EEOLICSBP-04/2026-27
Bidding Type Tender
Location
City Sambalpur
State Odisha
Key Dates
Publish Date 16 Nov 2026
Submission Date 30 Nov 2026
Open Date 01 Dec 2026
Finance
Tender Value 61.36 Lakhs
Tender Fee 11800
EMD 61365
Exemption Available
Document List
17902c0e-2005-4bed-bcde-0f2c07893ec7.html
BOQ_621256.xls
Tendernotice_1.pdf
Tendernotice_2.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 16, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 30, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 11 days
Dec 01, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 12 days

Tender Documents

Download All (ZIP) ↓
html

17902c0e-2005-4bed-bcde-0f2c07893ec7.html

xls

BOQ_621256.xls

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender