Defence Statutory Bodies & Commissions/Committees Closing in 14 days TDR #58540944

Tender For Providing Of Certain Sanctioned Works At Nagrota Mil Stn Under Ge Nagrota

Issued by Statutory Bodies & Commissions/Committees · Jammu, Jammu and Kashmir
Tender Value
42.80 Lakhs
Estimated cost
Bid Submission
05 Dec 2026
14 days left
EMD
85600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Providing Of Certain Sanctioned Works At Nagrota Mil Stn Under Ge Nagrota

BOQ

Name of Work:-
Sl. No. Item Description
1Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each and removing from site complete all as specified and directed.
2Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm each but n exc 4 sqm and removing from site complete all as specified and directed.
3Dismantling wrought iron or mild steel work of any description not other wise provided complete all as specified and directed.
4Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stone work and precast concrete articles complete all as specified and directed.
5Demolition of cement concrete (unreinforced) in ground floors and paving not exc 15cm thickness complete all as specified and directed.
6Demolition of cement concrete (Reinforced) of any description and any position not other wise specifically provided reinforcement cut as required to facilitate demoltion complete all as specified and directed.
7Dismantling cast-iron/PVC pipes including fittings taking out of trenches or walls as required dia of pipe upto 100mm complete all as specified and directed.
8S & F Box type Steel windows side hung double shutters (inside for wiremesh & outside for glass), including guard 10mm square bar, hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing. Steel window shall be conforming to relevant IS complete all as shown on drawing No- CEUZ/TD/1302/09 sheet No- 1/3 to 3/3 complete all as specified and directed.
9S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.
10S&F 3mm thick sheet glass, ordinary quality in squares n exc 0.5 sqm each panes etc complete all as specified and directed.
11M&L for Preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a priming coat of red oxide complete all as specified and directed.
12S&F in repair for 20 to 25 mm dia stainless steel drapery curtain rod with brass /nickel chromium polish / designer lattos and brackets including taking out old pelmet with curtain rods complete all as specified and directed.
13M & L for Brick work with sub-class `B' bricks, straight or curved on plan with modular bricks exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.
14Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed.
15M&L for Rendering 5 mm thick in CM (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.
16M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 without using extra cement complete all as specified and directed.
17M&L for rendering 15 mm thick on unfair faces of brick work or concrete surfaces in cement mortar 1:4 without using extra cement complete all as specified and directed.Note : WPC (5mm thick only) will be measured and paid separately.
18M&L for preparation of new plastered surface of CEILING and applying two coats of oil emulsion distemper over a coat of primer over 3 mm thick wall care putty complete all as specified and directed. Note: The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
19M&L for Preparing new plastered surfaces of wall and applying two coats of oil bound distemper over 3mm thick wall care putty etc complete all as specified and directed. Note: The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
20M&L for preparation of new plastered/unplastered surface and finishing walls with Acrylic Smooth exterior paint of required shade as approved by GE with two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on walls over 3mm thick cement based wall care putty including necessary scaffolding for max height of G+2 bldg with parapet, etc complete all as specified and directed.Note:- (a) Each stage i.e. preparation of surfaces, application of primer, application of first coat, application of second coat will be got passed from Engr-in -Charge.(b) The acrylic emulsion paint work shall be carried out by using smart painting tools and techniques as specified in Particular Specifications and Contractor will have to produce necessary documents for purchase of smart painting tools or rent receipt of these tools along with bill/RAR.The bidders are requested take this aspect in consideration before quoting their rate and no claim on account of misunderstanding or otherwise shall be admissible on this account. (c) The painting is to be done in one or more shades as approved by GE.
21Supply only Liquid water proofing compound complete all as specified and directed.
22M&L for preparation of old decorated plastered or unplastered surface including complete removal by brooming down with steel wire brushing, scraping down smoke soot, moulded, moss, efflorscent salt, trading oil and greasy spots and finishing walls with Acrylic Smooth exterior paint of required shade as approved by GE with two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on walls over 3mm thick cement based wall care putty including necessary scaffolding for max height of G+2 bldg with parapet, etc complete all as specified and directed.Note:- (a) Each stage i.e. preparation of surfaces, application of primer, application of first coat, application of second coat will be got passed from Engr-in -Charge.(b) The acrylic emulsion paint work shall be carried out by using smart painting tools and techniques as specified in Particular Specifications and Contractor will have to produce necessary documents for purchase of smart painting tools or rent receipt of these tools along with bill/RAR.The bidders are requested take this aspect in consideration before quoting their rate and no claim on account of misunderstanding or otherwise shall be admissible on this account. (c) The painting is to be done in one or more shades as approved by GE.
23M&L for preparation of old decorated plastered or unplastered surface including complete removal of existing treatment by machinary only, scraping down smoke soot, moulded, moss, efflorscent salt, trading oil and greasy spots and applying two coat of Oil emulsion distemper on walls over 3 mm thick wall care putty (in two or more layers) complete all as specified and directed.Note: The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
24M&L for preparation of old decorated plastered or unplastered surface including complete removal of existing treatment by machinary only, scraping down smoke soot, moulded, moss, efflorscent salt, trading oil and greasy spots and applying two coat of Oil emulsion distemper on CEILING over 3 mm thick wall care putty (in two or more layers) complete all as specified and directed.Note: The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
25Demoliton of Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.
26M & L for 25mm thick PCC 1:2:4 type B-1 as a sub base to receive topping layer finished even and rough complete all as specified and directed.
27M & L for Cement concrete 1:5:10 type E-2 using 40mm graded crushed stone aggregate as in any situation complete all as specified and directed.
28M & L for Machine cut kota stone flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone over cement concrete type B-1 (1:2:4) 25mm thick including grinding and polishing (mirror finish) (Each stone not less than 55 cms x 55 cms) over 15mm thick screed bed 1:4 of kota stone complete all as specified and directed.
29M & L for Machine cut kota stone slab 18-20mm thick in skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (mirror finish) over 10 mm thick rendering in CM (1:4) including taking out of existing dado complete all as specified and directed.
30M&L for Makrana white marble 18- 20mm thick machine cut, bedded jointed and pointed with white cement slurry including cutting and polishing types (mirror finish) over 15mm thick screed bed in CM (1:6) as in floor finished, complete all as specified and directed.
31Demolition of unreinforced cement concrete of any description and in any position complete all as specified and directed.
32M&L for Roughening surfaces of old concrete surfaces of any description over damaged surfaces irregular fascia, chajjas and in similar work and also for narrow width etc and rendering dubbing coat 15mm thick cement plaster in CM (1:4) over a coat of cement slurry @ 3.00 Kg/Sqm making surface even followed by 05mm thick rendering in CM (1:3) finished complete all as specified and directed.
33M&L for cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) in fdn filling and mass complete all as specified and directed.
34M & L for Chequered cement concrete tiles of size 30cm x 30cm x 25mm thick (with grey cement and pigments) set, jointed and pointed in neat cement slurry in floor, laid over and including 15mm thick cement screed base in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing, grinding complete all as specified and directed.
35M & L for sand filling under interlocking paver block including watering and consolidation complete all as specified and directed.
36M&L for Machine pressed pre cast concrete interlocking paver (with grey cement and pigment) any shape and size confirming to IS -15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed.
37M&L for machine pressed pre cast concrete interlocking paver (with grey cement and no pigment) any shape and size confirming to IS -15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed.
38M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded curshed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.
39Demolition of cement concrete (unreinforced) as in Roofs, floors (other than ground floors) including roof treatment any type, beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.
40M&L for Providing cement concrete 1:2:4 type B-0 (12.5mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges or as in padding concrete complete all as specified and directed.
41M&L for 10mm rendering in CM 1:4 including water proofing compound over roof surfaces finished even and smooth without using extra cement complete all as specified and directed.Note:- Qty of WPC 200ml per cement Bag or as per manufacturer instructions. WPC will be measured and paid separately.
42M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm including bitumen primer @ 3.5Kg/Sqm complete all as specified and directed.
43M&L for One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm, reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing complete all as specified and directed.Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions.(ii) A Minimum overlap of 100 mm and 75 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions. (iii) S&F of APP based polimeric membrane of approved manufacturer will be laid/fixed by well-trained applicators as per manufacturer's instructions after obtaining written approval from the GE.
44M&L for Applying Two coat of aluminium paint on top of APP membrane complete all as specified and directed.
45M&L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed with grey cement and pigment and pointed in neat cement slurry in floors, and cut and polished including laid over Screed bed or bedding layer of CM 1:4 mortar 15 mm thick for laying floor finishes complete all as specified and directed.
46Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store complete all as specified and directed.
47S&F PVC (SWR) pipes, 110mm dia, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and directed.
48S&F PVC (SWR) Bends any radius for 110mm bore complete all as specified and directed.
49S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, bore of pipe 110mm including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.
50S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, water tank, cooler stand etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe-410-W(GdeE-250) quality complete all as specified and directed.
51M & L for RCC 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate) as in chajjas, shelves and similar items complete all as specified and directed.
52M & L for Form work to chajjas troughs, shelves and similar items including edges complete all as specified and directed.
53S&F TMT bars 10mm dia and over cut to lengths bent to shape required including cranking bending and spirally hoping for columns hooking ends and binding with MS wire annealed not less than 0.90mm dia complete all as specified and directed.
54S&F TMT bars 6mm to 8mm dia cut to lengths bent to shape required including cranking bending and spirally hoping for columns hooking ends and binding with MS wire annealed not less than 0.90mm dia complete all as specified and directed.
55M&L PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in copings, benching, weathering and slightly chamfering complete all as specified and directed.
56S & F Steel rolling shutters (1.25 mm Thickness of laths) with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position complete, gear operated type with bevel gear box and crank handle complete acceseries complete all as specified and directed.
57S & F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.
58S & F Ball bearing for rolling shutters complete all as specified and directed.
59M&L PCC 1:2:4 Type B1 (using 20mm graded crushed stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating on top of chajjas complete all as specified and directed.
60M&L for writing letters or figures (Block, Roman, Italic or Indian) to building with synthetic enamel paint 65mm long and 10mm wide in words and figures such as (PN-10,TN-27,T-123 & T-81/2 etc) over black synthetic enamel painted ground of 150mm dia incl obliterating old writting of any description n exc 0.10 sqm with paint to match existing work complete all as specified and directed.Note- considering PN-10/TN-27/T-123/T-81/2 No as unit.
61Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Soft/ loose soil complete all as specified and directed.
62Excavation of trenches n.exc 1.5m wide and n.ex 1.5m in depth for foundation etc or for shafts, wells cesspits manholes, pier holes etc n.exc 10sqm on plan and n.exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.
63Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.
64Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.
65M & L for 75mm thick plain cement concrete type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in Sub base of flooring / hard standing etc complete all as specified and directed.
66M & L for Broken brick bat hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.
67M & L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls complete all as specified and directed.
68M & L for Reinforced cement concretetc M-25 (design Mix) using 20mm graded crushed stone aggregate as in foundation, plinth beams,footings etc, complete all as specified and directed.
69M & L for Reinforced cement concretetc M-25 (design Mix) using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and structs complete all as specified and directed.
70M & L for Reinforced cement concretetc M-25 (design Mix) using 20mm graded crushed stone aggregate as in floor or roof beams complete all as specified and directed.
71M & L for Reinforced Cement Concrete M-25(design Mix) for slabs suspended on walls, beams and columns, in floors, roofs, landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.
72M & L for Fair finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exceeding 200 mm thick (Horizontal or sloping) complete all as specified and directed.
73M & L for Fair finished flat Form work to sides of pillars, post, struts, piers, columns and stanchions complete all as specified and directed.
74M & L for rough finished surfaces of concrete formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.
75M & L for rough finished surfaces of concrete formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.
76S&F Framed work rolled section as in framing compound girder staging for end bars, shouldered and riveted, forged into spikes, framed guard bars, dooriron, ladders walk rails, railings, frame work for tanks, water tank,cooler frame as and the like built up from two or more beam or channel section or angles with plates stiffeners Fe 290 G E-165 etc complete all as specified and directed.
77M&L for Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.
78M&L for preparation of new plastered/unplastered surface and finishing walls with Acrylic Smooth exterior paint of required shade as approved by GE with two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on walls over 3mm thick cement based wall care putty including necessary scaffolding etc complete all as specified and directed.Note:- (a) Each stage i.e. preparation of surfaces, application of primer, application of first coat, application of second coat will be got passed from Engr-in -Charge.(b) The acrylic emulsion paint work shall be carried out by using smart painting tools and techniques as specified in Particular Specifications and Contractor will have to produce necessary documents for purchase of smart painting tools or rent receipt of these tools along with bill/RAR.The bidders are requested take this aspect in consideration before quoting their rate and no claim on account of misunderstanding or otherwise shall be admissible on this account. (c) The painting is to be done in one or more shades as approved by GE.
79Supply only integral water proofing compound complete all as specified and directed.
80M&L for Preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.
81M&L for non skid cereamic coloured tiles 7 to 8mm thick (square/ rectangle) area of each tiles exceeding 0.11 sqm but n. exc.0.18 sqm, in floor etc set and joined in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick in cement mortar 1:6 screed bed or bedding layer of mortar for laying floor finishes complete all as specified and directed.
82M & L glazed, ceramic, coloured tiles of size 350x250x7mm/450x350x7mm thick, on vertical surfaces such as skirting, dados etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles including endering 10 mm thick in cement mortar (1:3) as in bedding layer for laying of tiles in vertical surfaces complete all as specified and directed.
83S & F solid PVC door frames of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and directed.
84S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC \\"C\\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS framewelded/ sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement in the frame at site as per specification complete all as specified and directed.
85S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.
86S & F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and directed.
87S & F 150mm size extruded aluminium handle cast type anodised complete all as specified and directed.
88S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints laid in floors or trenches, etc including necessary excavation & earth work whenever required complete all as specified and directed.
89S & F 110mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints laid in floors or trenches, etc including necessary excavation & earth work whenever required complete all as specified and directed.
90S & F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.
91S & F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.
92S & F 15 mm bore galvanized steel tubes, medium grade with all fittings complete fixed to walls and ceilings or laid in floors complete all as specified and directed.
93S & F 20 mm bore galvanized steel tubes, medium grade with all fittings complete fixed to walls and ceilings or laid in floors complete all as specified and directed.
94S & F 15 mm bore CP Bip taps (fancy type), cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.
95S & F stop valve 15mm bore cast copper alloy chromonium plated fancy type screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.
96S&F 15 mm size angular cock, cast copper alloy (fancy type) with long body, chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed.
97S & F PVC connection pipe 15mm size with PTMT nuts of 600 length including fixed complete all as specified and directed.
98S&F 20 mm bore, ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.
99S&F 500 ltr capacity Rotational moulded polythylene trippled layer water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.
100S & F vitreous china squatting pan \\"orissa pattern, size 630x450mm white, with integral foot rests(excluding flushing cistern and flush pipe) including provison of lean concrete bedding connection to drain out pipe, to flush pipe and antisyphonage pipe etc complete all as specified and directed.
101S & F vitreous china wash down water closet pan (pedestal pattern) white with integral foot rests(excluding flushing cistern and flush pipe) including provison of lean concrete bedding connection to drain out pipe, to flush pipe and antisyphonage pipe etc, complete all as specified and directed.
102S& F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve float and handle including brackets (10 ltr) including mild steel tube 32mm dia flush pipe complete all as specified and directed.
103S&F PVC (SWR) 100mm dia floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.
104S&F white vitreous china counter wash hand basin, of size-410X910X150mm fixed in granite counter by making suitable size hole, new brackets, 32mm dia brass chromium plated waste coupling, CP botle trap complete all as specified and directed.
105S&F Looking mirror 600m x 450mm of selected quality 8 mm thick glass moulded edges fixed to plugs with chromium plated brass screws complete all as specified and directed.
106S&F 15 mm size pillar cock, cast copper alloy (fancy type), chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed.
107S&F PTMT single towel Rail of size 600 mm long complete all as specified and directed.
108S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.
109S&F stainless steel soap dish holder including fixing arrangement complete all as specified and directed.
110S&F of 125 mm dia Fancy type Chromiun plated shower rose fixed to 15mm dia pipe complete all as specified and directed.
111S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms),Waste coupling of PTMT(Minimum weight32mm-45gm) (half or full threaded) complete all as specified and directed.
112S & F Vitreous china urinal partition white of size 310x700 mm, Urinal partitions slabs terminating about 40cm above floor line complete all as specified and directed.
113S&F in repair Box type Steel ventilators top hung double shutters (inside for wire mesh & out side for glass), including hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing. Steel window shall be conforming to relevant IS all as specified.including taking down old shutter complete all as specified and directed. Note:- Wire mesh and sheet glass shall be measured and paid separately
114S&F Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.
115S&F 150mm dia Reinforced concrete pipes, class NP-2 laid and jointed complete all as specified and directed.
116M & L for 150 mm cement concrete 1:4:8 type D-2 in bed to drain pipes incls packing under, and haunching against the sides of pipes after they are laid and tested of bore 150mm to 300mm dia drain pipe complete all as specified and directed.
117Excavating in trenches, n exc 1.5 m wide and exc 1.5 m but n. exc 3.00 m in depth; for foundation, etc. getting out in any type of soil complete all as specified and directed.
118Excavating in trenches, n exc 1.5 m wide and exc 3.0 m but n. exc 4.50 m in depth; for foundation, etc. getting out in any type of soil complete all as specified and directed.
119Removing excavated material exc. 250 m but n exc. 500 m and depositing complete all as specified and directed.
120M&L for hard core of broken stone n exe 63 mm, deposited, spread and levelled in layers n exc 15 CM thick, watered and rammed to a true surface complete all as specified and directed.
121M&L for cement concrete 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) in fdn filling and mass concrete complete all as specified and directed.
122M&L for brick work with sub class 'B' well burnt old size bricks straight or curved on plain exceeding 6 metre mean radius built in cement mortar (1:4) for manhole and pointed flush externally in same mortar as the work proceeds complete all as specified and directed.
123M & L fot brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:6 with honey comb 525 band as in half brick thick walls complete all as specified and directed.
124M&L for Loose filling with broken bricks of gauge 80 to 150mm in soakage pits, soakage wells, complete all as specified and directed.
125M&L for concrete bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150mm bore pipes complete all as specified and directed.
126M & L for Salt -Glazed stoneware drain pipes 150 mm dia laid in trenches and jointed complete all as specified and directed.
127M & L for 150mm Bore / inner dia double wall, corrugated HDPE Pipe (SNB) (ISI Marked) with integral socket & necessary fitting jointing as directed & laid in trenches complete all as specified and directed.
128M&L for cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) in benching, bed plates, copinga nd the like including weathering, slightly rounded or chamfered angles, including necessary form work and finishing all exposed to surfaces complete all as specified and directed.
129M & L for Precast cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in manhole/drain slab cover and set in CM 1:4 complete all as specified and directed.
130S&F TMT bars 5mm dia incl over upto 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.
131S&F mild steel angle iron/flat iron work as in manhole cover frames and conforming to Fe-290 (Gde E-165) complete all as specified and directed.
132S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.
133S&F PVC (SWR) vent cowl complete all as specified and directed.
134Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required for 110 mm bore pipe complete all as specified and directed.
135Dismantling of barbed wire fencing of any description and any positions complete all as specified and directed.
136M & L for Brick work(Expect brick) with sub class B modular bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 in any position complete all as specified and directed.
137S&F MS angles as in horns of posts, wall including cutting at top to shape as directed drilling holes nothing wire etc including necessary drilling, bolting or welding etc conforming to Fe 290 Gde-E-165 complete all as specified and directed.
138M&L for rendering 15mm thick in CM 1:4 on other than fair faces of brick or concrete surface with liquid water proofing compound @ 200 ml per bag finished even and smooth without using extra cement complete all as specified and directed.(Note:- Liquid water proofing compound to be measured and paid separately)
139Material and Labour for apply two coats of Anti fungal weather coat acrylic emulsion paint over a coat of primer on new surfaces including 2 -3 mm thick wall putty, complete all as specified and directed. Note:- (a) Each stage i.e. preparation of surfaces, application of primer, application of first coat, application of second coat will be got passed from Engr-in -Charge.(b) Written Warranty for four years or as per manufacturer's instructions, whichever is more is required to be furnished by contractor for this item.(c) The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
140M&L for Preparation old steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.
141M&L Plain cement concrete type B1 (1:2:4) using 20mm graded crushed stone aggregate as in levelling course and other works as in roof, kerb, coping, padding etc complete all as specified and directed.
142S & F Galvanized, 2 strand, steel barbed wire 2.5 mm dia., barbed with 2.5 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel pins etc complete all as specified and directed.
143Supply and fixing 600mm dia Galvanised steel punched type concertina coil as per IS-4454 with galvanised coating and punched type material as per IS-513 deep drawn quality with galvanised coating, having medium bardbs (barb length 24+1mm pitch between two barbs 35+1mm) fixed in position and secured to both sides of shaped angle iron post stretched to a length of 8 to 10m so as to achieve 600mm dia as in fencing including fixing with special galvanised fasteners such as J clips, C clips, U clips fixed at any height on compound wall including dismantling old concertina coil wire including necessary scaffolding as required complete all as specified and directed.[Note: After stretching the coil the length of the compound wall on which it has been stretched shall be measured as straight length for payment]
144M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite with providing 10mm thick rendering in CM 1:4 complete all as specified and directed
145M&L for glazed ceramic coloured wall tiles (textured and design as required) in vertical surface 450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in 1:4 CM complete all as specified and directed
146M & L for brick work with old size brick with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed
147M & L for rendering 15mm thick in two layer (10mm+5mm) in cement mortar 1:4 on fair faces of brick work / concrete surfaces finished even and fair with out extra cement complete all as specified and directed
148M & L for preparation of new plastered surface of wall and applying two coats of oil emulsion distemper over a coat of alkali resistance primer complete all as specified and directed. Note: The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
149M & L preparation of new decorated surfaces of external walls and applying two coat of cement base paint over a coat of primer complete all as specified and directed. Note: The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
150M & L preparation of old decorated surfaces of external walls and applying two coat of cement base paint over a coat of primer complete all as specified and directed.Note: The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage.
151M&L for preparation of old plastered surfaces of ceiling and applying two coat of white wash complete all as specified and directed.
152S & F for Glazed ceramic coloured printed tiles of size 600 mm x 450 mm x 7mm thick or 450x 3000mm x7mm thick as in dados, skirting, wall etc set jointed in neat cement slurry and pointed in coloured cement to match the tiles over and including 10 mm thick rendering in CM 1 : 4 for laying glazed tiles in floors etc. complete all as specified and directed. Please Enable Macros to View BoQ information
153S & F for Glazed ceramic coloured printed tiles of size 600 mm x 450 mm x 7mm thick or 450x 3000mm x7mm thick as in dados, skirting, wall etc set jointed in neat cement slurry and pointed in coloured cement to match the tiles over and including 10 mm thick rendering in CM 1 : 4 for laying glazed tiles in floors etc. complete all as specified and directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58540944
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 42.80 Lakhs
LAST DATE 05-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Providing Of Certain Sanctioned Works At Nagrota Mil Stn Under Ge Nagrota
Basic Detail
Tender No CANO GEN/TOKEN-97/2026-2027
Bidding Type Tender
Location
City Jammu
State Jammu and Kashmir
Key Dates
Publish Date 14 Nov 2026
Submission Date 05 Dec 2026
Open Date 10 Dec 2026
Finance
Tender Value 42.80 Lakhs
Tender Fee 500
EMD 85600
Exemption Available
Document List
0362587d-3e1a-41e2-98d8-70cb86c81528.html
BOQ_896096.xls
Tender97.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 14, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 05, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 14 days
Dec 10, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 19 days

Tender Documents

Download All (ZIP) ↓
html

0362587d-3e1a-41e2-98d8-70cb86c81528.html

xls

BOQ_896096.xls

pdf

Tender97.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender