Tender For Repairing Of Pathway Old Damaged Extra Wall And Other Allied Work At Regional Store Under Govindpur Area
Tender Value
5.50 Lakhs
Estimated cost
Bid Submission
25 Nov 2026
3 days left
EMD
7000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhanbad → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing Of Pathway Old Damaged Extra Wall And Other Allied Work At Regional Store Under Govindpur Area
BOQ
| Sl. No. | Item Description |
| 1 | Civil work |
| 2 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking thematerial within 50 metres lead of:G.S. Sheet |
| 3 | Demolishing brick work manually/ by mechanical means including stacking of serviceablematerial and disposal of unserviceable material within 50 metres lead as per direction ofEngineer-in-charge in cement mortar |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost ofcentering and shuttering - All work up to plinth level1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stoneaggregate 40 mm nominal size derived from natural sources) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost ofcentering and shuttering - All work up to plinth level1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stoneaggregate 20 mm nominal size derived from natural sources). |
| 6 | STEEL WORKStructural steel work in single section, fixed with or without connecting plate, includingcutting, hoisting, fixing in position and applying a priming coat of approved steel primerall complete |
| 7 | Finishing walls with water proofing cement paint of required shade :Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primerapplied @ 0.80 litrs/10 sqm complete including cost of Priming coat |
| 8 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratches duringtransportation and should be supplied in single length upto 12 metre or as desired byEngineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size(5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curvedsurfaces, excluding the cost of purlins, rafters and trusses and including cutting to size andshape wherever required |
| 9 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths,interlocked together through their entire length and jointed together at the end by endlocks, mounted on specially designed pipe shaft with brackets, side guides andarrangements for inside and outside locking with push and pull operation complete,including the cost of providing and fixing necessary 27.5 cm long wire springsmanufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -part 1 and M.S. top cover of required thickness for rolling shutters80x0.90 mm M.S. laths with 0.90 mm thick top cover |
| 10 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle ironand 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete,including applying a priming coat of approved steel primer.Using flats 30x6mm for diagonal braces and central cross piece |
| 11 | Extra for providing mechanical device chain and crank operation for operating rollingshutters.Exceeding 10.00 sqm and upto 16.80 sqm in the area |
| 12 | Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar insteadof laths as per design approved by Engineer-in- charge, (area of grill to be measured). |
| 13 | 12 mm cement plaster of mix 1:4 (1 cement : 4fine sand) |
| 14 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysNov 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender