Defence Statutory Bodies & Commissions/Committees Closing in 16 days TDR #58539941

Tender For special Repair To Rrf Treatment, Tiling, Sanitary Fitting, Joinery And Other Misc Work In Bldg No Sm-4 Or Single Accn At Zone-8 Under Age B/R-I & Age E/M Under Ge Babina

Issued by Statutory Bodies & Commissions/Committees · Jhansi, Uttar Pradesh
Tender Value
48.55 Lakhs
Estimated cost
Bid Submission
07 Dec 2026
16 days left
EMD
97100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Jhansi → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for special Repair To Rrf Treatment, Tiling, Sanitary Fitting, Joinery And Other Misc Work In Bldg No Sm-4 Or Single Accn At Zone-8 Under Age B/R-I & Age E/M Under Ge Babina

BOQ

Name of Work:- SPL REPAIR TO RRF TREATMENT, TILING, SANITARY FITTING, JOINERY AND OTHER MISC WORK IN BLDG NO SM-4 OR SINGLE ACCN AT ZONE-8 UNDER AGE B/R-I & AGE E/M UNDER GE BABINA
Sl. No. Item Description
1Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key etc., complete all as specified and as directed.
2M&L for rendering 10mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth etc., complete all as specified and as directed.
3M&L for rendering 5mm thick ceiling plaster in CM (1:3) on concrete surfaces finished even & smooth (without using extra cement) etc., complete all as specified and as directed.
4M&L for rendering 5mm thick plaster in CM (1:4) over a backing coat of 10 mm thick in CM 1:6 (Total 15 mm thick) on concrete or block masonry surfaces including mixing water proofing compound on top layer as per manufactures instructions (or 3% by weight of cement) and finishing the top surfaces even and fair etc., complete all as specified and as directed. (Note :Water proofing compound shall be measured and paid seperately under relevant item of this schedule as supply only).
5Supply only water proofing compound ISI marked etc., complete all as specified and as directed. (Note : WPC may apply as per manufactures instructions or 3% by the wt of cement).
6M&L for preparation of new plastered surfaces of wall and applying two coats of Distempering with 1st quality acrylic distemper ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour as per manufacturer's specification etc., complete all as specified and as directed.
7M&L for newly plastered surfaces and applying two coats of oil bound distemper over a coat of Chalk whiting, on plastered surfaces of ceiling etc., complete all as specified and as directed.
8M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.Make :- Asian Apex Ultima and Equivalent
9M&L for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc., complete all as specified and as directed.(on truss work & new pressed steel frame)
10M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc and applying two coats of oil emulsion distemper over a coat of primer etc., complete all as specified and as directed.
11M&L for applying a layer of 1mm thick wall care putty on wall and making surface even and smooth etc., complete all as specified and as directed.
12M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc and preparation of old external surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, complete all as specified and as directed.Make :- Asian Apex Ultima and Equivalent
13M & L for preparation of old ceiling surfaces and applying two coats of white wash complete all as specified and directed.
14M&L for preparation of old painted wooden surface and applying two coats of synthetic enamel paint of any description exc 10 cm width or girth, etc., complete all as specified and as directed.
15M&L for preparation of old painted steel surfaces over 10 cm in width or girth and applying two coats of syanthetic enamel paint etc., complete all as specified and as directed.
16Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) etc., complete all as specified and as directed.
17Demolition of brick work built in cement mortar complete all as specified and as directed.
18M&L Brick work with sub class B bricks straight or curved on plan exe 6 m mean radius built in cement mortar 1:4 complete all as specified and as directed
19M&L for 75mm thick PCC 1:3:6 Type C-2 (using 40mm crushed stone aggregate) as in plinth protection finished even and fair without using extra cement etc., complete all as specified and as directed.
20Dismantling floor, hearth or wall tiles including cement mortar bedding (but not backing) and removing serviceable tiles to stores and rubbish off the premises etc., complete all as specified and as directed.
21M&L, screed bed or bedding layer of mortar 15 mm thick in cement mortar 1: 6 to receive tiles etc finished rough complete all as specified and directed.
22M&L 25mm thk PCC 1:2:4 type B-0 using 12.5 mm graded agg as in flooring finished fair and even without using extra cement complete all as specified and as directed.
23M&L for 1st quality Ceramic tiles light or dark shed 7-8 mm thick, (square/ rectangular), area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,polished, in floors etc.jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
24M&L for 1st quality Ceramic tiles light or dark shed 7-8 mm thick, (square/ rectangular), area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.
25M&L for 1st quality non skid white ceramic tiles 6 to 8 mm thick (square / rectengular) area of each tile exceeding 0.18sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.
26M&L for 1st quality glazed ceramic white/coloured wall tile 1200x600x7-8 mm thick on skiriting/dado, set & jointed with high-performance adhesives , grouts and cleaning & pointed with white/coloured cement to match inc for laying tiles on skirting/dado including rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces as in vertical surfaces for receiving tiles complete all as specified and as directed.
27M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed.
28Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified.
29Taking down chowkats or frames (without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.(including Aluminium windows/ ventilators) etc., complete all as specified and as directed.
30Taking down chowkats or frames (without taking off shutters from the frame) area n.exc 1.5 Sqm each.(including Aluminium windows /ventilators) etc., complete all as specified and as directed.
31S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).
32S&F for Factory made double extruded WPC (Wood Polymer Composite) solid door & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length etc., complete all as specified and as directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).
33S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws incl in this item)
34&F 30 mm thick FACTORY MADE WIRE MESH SOLID WPC both side solid plain DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company,including SS mosquito Mesh and XTN aluminium Mesh with aluminum deco grill for additional strength and safety purpose. (confirming as per S:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings. complete all as specified and directed. (Note: Cost of stainless steel butt hinges and necessary S.S screws will be included in qouted rate. )
35Supply and fixing factory made uPVC white colour Three track and three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) including outer frame/track upto 1.50m height made of including outer size frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.
36After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
37S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified as directed.
38M&L, framed work as grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165 etc complete all as specified and as directed
39S&F for 4mm thick ordinary quality sheet glass and glazing with oil putty in square n.exc.0.50 sqm in each pane etc., complete all as specified and as directed.
40S&F for 4mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sq.m in each pane etc., complete all as specified and as directed.
41S&F for Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples etc., complete all as specified and as directed.
42S&F for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed etc., complete all as specified and as directed.
43S & F in repair for 18mm thick UV coating, MDF board exterior grade, Both side laminated with any colour anti fungal,moisture resistence,anti borer, as per IS 14587 for kitchen/Cupboards shelfs fixing with 1st class hard wood lipping/beading and including necessary fixing aragement to wall etc. complete all as specified and directed by Engg-in-charge. Note:- (i) Sample and design of moduler box as approved by Engr-in-charge.(ii) Area will be measured only front side of moduler box for payment to contractor
44S&F for 150 mm long Brass handles, cast type, polished bright etc., complete all as specified and as directed.
45S&F for contunoius (piano) hinges , mild steel , bright finish or electrogalvanished and width of flaps 30 mm (when open) etc., complete all as specified and as directed.
46S&F, stainless steel (SS-304 grade),100 mm size etc complete all as specified and as directed.
47S&F, aluminum handles cast type anodized 125 mm size etc complete all as specified and as directed
48S&F, aluminum anodized barrel tower bolts of extruded section 150 mm long etc complete all as specified and as directed
49S&F, aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) 300mm long etc complete all as specified and as directed
50S&F for 300mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed etc., complete all as specified and as directed.
51S&F in repair for 150mm Floor door stoper of aluminium alloy and tounge, anodised, with hard drawn steel sring, fixed in door etc., complete all as specified and as directed.
52S&F in repair for door helical spring mild steel 300mm, ordinary rat tail rod patteren including roller and roller plate etc., complete all as specified and as directed.
53S&F in repair chromium plate curtain rod with CP brackets and knobs at both end as per sample approved by Engineer-in-charge.
54Taking down 20mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed.
55Taking down 25/32mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed.
56Supply and laying of CPVC pipes 20 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors etc., complete all as specified and as directed.
57Supply and laying of CPVC pipes 25 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors complete all as specified.
58Cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing etc., and making good, cutting not exceeding 10 cm girth etc., complete all as specified and as directed.
59Taking down eaves gutter and rain / waste water pipes including all fittings any size and pattern etc., complete all as specified and as directed.
60S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing as required etc., complete all as specified and as directed.
61S&F for 110 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed.
62S&F for 110mm bore PVC (SWR) junction single, (single T) equal or unequal with access door etc., complete all as specified and as directed.
63S&F for 110 mm bore PVC (SWR) junction double ,(double T) equal or unequal with access door etc., complete all as specified and as directed.
64S&F for 110 mm bore PVC (SWR) couplers etc., complete all as specified and as directed.
65S&F for 110 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed.
66S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing on walls as required etc., complete all as specified and as directed.
67S&F for 75 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed.
68S&F for 75 mm bore PVC (SWR) junction single, (single T) equal or unequal with access door etc., complete all as specified and as directed.
69S&F for 75 mm bore PVC (SWR) junction double, (double T) equal or unequal with accessa door etc., complete all as specified and as directed.
70S&F for 75 mm bore PVC (SWR) couplers etc., complete all as specified and as directed.
71S&F for 75 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed.
72M&L for PVC (SWR) floor traps 75mm bore with stainless steel grating (measured seperately) including jointing to waste pipe and in cement concrete 1:2:4 type B-1 etc., complete all as specified and as directed.
73S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement etc., complete all as specified and as directed.
74S&F in repair of 1st quality vitreous china ware European type WC of size 540x375x415mm 'P' trap or 'S' Trap (pedestal pattern), any colour including necessary fittings (excluding flushing cistern and flush pipe) etc., complete all as specified and as directed.
75S&F in repair of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface etc., complete all as specified and as directed.
76Supply only 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, any colour , with inlet, ball valve, float and handle including brackets, and necessary connections to pipes with PVC connections 20mm size with PTMT nuts of length 600mm etc., complete all as specified and as directed.
77S&F in repairs PVC water closet seat cover (any description and any colour), closed pattern and mild steel chromium plated or aluminised hinging device etc., complete all as specified and as directed.
78S&F in repair Heavy Duty Flexible Braided PVC waste pipe for sink and wash basin 32mm dia with length not less than 1000mm i/c PVC waste fittings of Approved make etc., complete all as specified and as directed.
79S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position etc., complete all as specified and as directed.
80S&F in repair Vitreous China wash basin, white, flat back, size 450x300mm fixed on MS brackets including 32 mm bore CP waste coupling and PVC connections 15mm size with PTMT nuts of length 600mm etc., complete all as specified and as directed.
81Supply only Pillar taps,heavy duty chromium plated, swan neck fancy type 15 mm dia cast copper alloy, with capstan heads, ,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed etc., complete all as specified and as directed.
82S&F in repair 600x450mm size and 4 mm thick beveled edge looking mirror of selected quality glass, having PVC moulding/beading all around, mounted on 5mm thick PVC board, with and incl fixing accessories etc., complete all as specified and as directed.
83S&F in repair CP Towel Ring fixed with and including Chromium plated brass screws and wall plugs (Minimum weight 90gms) etc., complete all as specified and as directed.
84S&F in repairs 600 mm long CP Brass Towel Rail 20 mm dia fixed to wall with necessary chromium plated screws and wall plugs etc., complete all as specified and as directed.
85S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to CPVC/ steel pipe or union etc., complete all as specified and as directed.
86S&F in repair Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed.
87S&F in repair to Bib Taps, cast copper alloy heavy duty, 15 mm dia, Chromium Plated, long body Fancy Type screwed down for iron pipe and fixed etc., complete all as specified and as directed.
88S&F in repair two way bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed.
89S&F in repairs 15 mm dia Stop cock chromium plated fancy type with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe/CPVC pipe or for unions and fixed etc., complete all as specified and as directed.
90Demolition of existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down , existing plaster etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush etc., complete all as specified and as directed.
91M&L for 10mm thick rendering/screed on terrace or concrete surfaces in cement mortar 1:4 finished even and fair and apply WPC (WPC @3% by wt of cement measured and paid seperately) etc., complete all as specified and as directed.
92M&L applying water proofing treatment comprising with the following:- (a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated. (b) after the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction. (c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane including Aluminium paint on top surface
93Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.
94M&L for Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed by Engineer-in-Charge for the \\"One light point controlled by one switch'
95All as per item No 93 One Exhaust fan point controlled by one switch.
96All as per item No 93 One ceiling fan controlled by one switch and one regulator
97All as per item No 93 One 6A socket point controlled by one switch on independent board
98All as per item No 93 One 6A socket point controlled by one switch on same board
99All as per srl item no. 93 here-in-before but with 4 sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board.
100S&F, Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed.
101S&F, Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed.
102S&F, Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed.
103S&F, Socket, two-in-one, 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed.
104S&F, angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed.
105Supply and fix electronic fan regulator in 5 steps, 240V, 120 W 50Hz complete all as specified and directed.
106S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.
107S & F 9/10 W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed..
108M&L for Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed by Engineer-in-Charge. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length complete all as specified and directed. Please Enable Macros to View BoQ information
109M&L for Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed by Engineer-in-Charge. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length complete all as specified and directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58539941
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 48.55 Lakhs
LAST DATE 07-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for special Repair To Rrf Treatment, Tiling, Sanitary Fitting, Joinery And Other Misc Work In Bldg No Sm-4 Or Single Accn At Zone-8 Under Age B/R-I & Age E/M Under Ge Babina
Basic Detail
Tender No 8615/E8
Bidding Type Tender
Location
City Jhansi
State Uttar Pradesh
Key Dates
Publish Date 14 Nov 2026
Submission Date 07 Dec 2026
Open Date 11 Dec 2026
Finance
Tender Value 48.55 Lakhs
Tender Fee 500
EMD 97100
Exemption Available
Document List
8615E8_CreditSchedule_1.pdf
8615Tenderdoc.pdf
9874ae58-c299-49ae-8acd-f1be44b0f280.html
BOQ_896089.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 14, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 07, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 16 days
Dec 11, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 20 days

Tender Documents

Download All (ZIP) ↓
pdf

8615E8_CreditSchedule_1.pdf

pdf

8615Tenderdoc.pdf

html

9874ae58-c299-49ae-8acd-f1be44b0f280.html

xls

BOQ_896089.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender