Tender For Construction And Development Work Of Community Center In Gomti Nagar Extension Sector-4.
Tender Value
16.57 Crore
Estimated cost
Bid Submission
30 Nov 2026
9 days left
EMD
33.16 Lakhs
Bank guarantee accepted
Document Fee
8000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Lucknow → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction And Development Work Of Community Center In Gomti Nagar Extension Sector-4.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m., All kinds of soil.DSR 2023- 2.8.1 |
| 2 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc., complete.DSR 2023- 2.25A |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :, 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).DSR 2023- 4.1.8 |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.DSR 2023- 2.27 |
| 5 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) :, Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :, With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.DSR 2023- 2.35.3.1 |
| 6 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) :, Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole :, With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.DSR 2023- 2.35.4.1 |
| 7 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement, All works upto plinth level, Concrete of M25 grade with minimum cement content of 330 kg /cumDSR 2023- 5.33.1.1 |
| 8 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:, Cement mortar 1:6 (1 cement : 6 coarse sand)DSR 2023- 6.1.2 |
| 9 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources).DSR 2023- 4.10 |
| 10 | Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.DSR 2023- 4.13 |
| 11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level., Cold twisted barsDSR 2023- 5.22.3 |
| 12 | 15 mm cement plaster on rough side of single or half brick wall of mix :, 1:4 (1 cement: 4 coarse sand)DSR 2023- 13.5.1 |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for :, Centering and shuttering including strutting and propping and removal of items for: Foundations, footings, base of columns, etc DSR 2023/5.9.1DSR 2023- 5.9.1 |
| 14 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :, All kinds of soil, Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm diaDSR 2023- 2.10.1.2 |
| 15 | Providing and fixing of Kent Elite Plus Water Purifier (RO+UV+UF+TDS Control) with flow rate (50L/hr) including all its accessories, complete in all respect including testing etc.- 28NSR |
| 16 | 6 mm cement plaster of mix :, 1:3 (1 cement: 3 fine sand)DSR 2023- 13.16.1 |
| 17 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels., Granite stone slab colour black, Cherry/Ruby red, Area of slab over 0.50 sqmDSR 2023- 8.2.2.2 |
| 18 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge., Granite workDSR 2023- 8.3.2 |
| 19 | Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. completeDSR 2023- 8.5 |
| 20 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily., Double charge vitrified tile polished finish of size, Size of Tile 600 x 600 mmDSR 2023- 11.41A.1.1 |
| 21 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily., Glazed Vitrified tiles Matt/Antiskid finish of size, Size of Tile 600 x 600 mmDSR 2023- 11.41A.3.1 |
| 22 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete., Size of Tile 600x600 mmDSR 2023- 11.46.2 |
| 23 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :, 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)DSR 2023- 4.1.3 |
| 24 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:, 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screwsDSR 2023- 9.21.3 |
| 25 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:, Supply & fixing of flush doors commercial quality conforming to IS 2202 Part I (1983) including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts locks handles springs fitting with necessary screws to be supplied departmentally (a) 30mm thickDSR 2023- 9.21.2 |
| 26 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with M.S hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/ window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variationin profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made., Frame size 65 x 100 mmDSR 2023- 26.86.5 |
| 27 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately), 35 mm thickDSR 2023- 26.88.2 |
| 28 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer., Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).DSR 2023- 10.13.1 |
| 29 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds., Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body., Using R3 series with frame (55mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system (Height upto 1.8m)DSR 2023- 9.147.A1.2 |
| 30 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :, 5.5 mm thick glass panes.DSR 2023- 10.30.2 |
| 31 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete .DSR 2023- 14.34 |
| 32 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :, Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete: 300x16 mmDSR 2023- 9.96.1 |
| 33 | P/Fixing stainless steel tower bolts ISI marked to required colour or shade with necessary screws etc.(a) 250 mm x 10mm DSR2023-9.74.1DSR 2023- 9.74.1-283 |
| 34 | Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :, Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mmDSR 2023- 9.100.1 |
| 35 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.DSR 2023- 9.83 |
| 36 | Providing /laying of light cinder filling/ 25 TO 40 mm O.B. brick ballast under floor of toilet /sunken roofs. PSR- Light cinder filling |
| 37 | Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in- Charge. (The payment shall be made on the basis of actual weight of approved grout injected.), Epoxy injection grout in concrete/RCC work of approved makeDSR 2023- 26.35.3 |
| 38 | Providing and laying matt finished vitrified tile of size 300x300x9.8mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.DSR 2023- 16.89 |
| 39 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspectionof work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment shall be made once irrespective of duration of scaffolding.Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.DSR 2023- 14.72 |
| 40 | Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @ 80 gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size 24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge., With 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100) specificationsDSR 2023- 26.27.3 |
| 41 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of, 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)DSR 2023- 12.45.1 |
| 42 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge., GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.DSR 2023- 12.52.1 |
| 43 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:- 2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL (National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL accredited lab or any other accredition body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 (1) Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr (2) Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. (3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml (4) Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm (5) Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test. Tests to be conducted on site. (6) Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 mlDSR 2023- 25.2 |
| 44 | Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc., all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Air gap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by the technical sanctioning authority as per the site requirement.DSR 2023- 25.3 |
| 45 | Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc., all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in- Charge.DSR 2023- 25.4 |
| 46 | Providing And Fixing 12 mm frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fitting, all complete as per direction of Engineer-in-Charge.- PSR-4207.21 |
| 47 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge., With stainless steel cover plate minimum 1.25 mm thickness.DSR 2023- 21.4.1 |
| 48 | TOILET CUBICAL- TOILET CUBICAL PARTITIONS |
| 49 | Providing and fixing of Water Cooler (Voltas Make) including all its accessories, complete in all respect including testing etc.- WATER COOLER |
| 50 | Providing and fixing of storage type (pressurised type) electric hot water heater copper sheet container, 25 mm thick insulation, stove enamelled M.S. jacket thermostatically controlled immersion heater with pilot neon lamp, suitable length of electrical cable and 15 amp 3 pin plug top, complete in all respect including testing etc.- WATER HEATER |
| 51 | Providing, Fixing, Testing & Commissioning of XLPE Insulation of 9mm thickness on hot water supply pipes. Astral or equivalent approved complete in all respect as directed by Engineer-in-charge. (15mm dia (9 mm thickness)- HOT WATER SUPPLY-1 |
| 52 | Providing, Fixing, Testing & Commissioning of XLPE Insulation of 9mm thickness on hot water supply pipes. Astral or equivalent approved complete in all respect as directed by Engineer-in-charge. (20mm dia (9 mm thickness)- HOT WATER PIPE-2 |
| 53 | \\"Providing and fixing MS pipe puddle flanges of required size with 600mm long with 6mm thick MS plate of size 300mm x 300mm of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks. \\" (25mm dia.)- 25MM |
| 54 | \\"Providing and fixing MS pipe puddle flanges of required size with 600mm long with 6mm thick MS plate of size 300mm x 300mm of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks. \\" (50mm dia. )- 50MM |
| 55 | \\"Providing and fixing MS pipe puddle flanges of required size with 600mm long with 6mm thick MS plate of size 300mm x 300mm of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks. \\" (65mm dia. )- 65MM |
| 56 | \\"Providing and fixing MS pipe puddle flanges of required size with 600mm long with 6mm thick MS plate of size 300mm x 300mm of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks. \\" (100mm dia.)- 100MM |
| 57 | \\"Providing and fixing MS pipe puddle flanges of required size with 600mm long with 6mm thick MS plate of size 300mm x 300mm of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks. \\" (150mm dia.)- 150MM |
| 58 | Providing, fixing, jointing and testing, uPVC SWR pipes, - type B conforming to IS : 13592 to wall, ceiling and floor, approved quality, complete, for soil, waste & rain water drain including pushfit jointing with seal ring. (i) Single socketed pipes. (75MM)- SWR PIPE-1 |
| 59 | Providing, fixing, jointing and testing, uPVC SWR pipes, - type B conforming to IS : 13592 to wall, ceiling and floor, approved quality, complete, for soil, waste & rain water drain including pushfit jointing with seal ring. (i) Single socketed pipes. (110MM)- SWR PIPE-2 |
| 60 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. (Bend without door (45°) (75mm)- PVC-1 |
| 61 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. (Bend without door (45°) (110mm)- PVC-2 |
| 62 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. (Bend without door (87.5°) ) (75mm)- PVC-3 |
| 63 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Y' Fitting without door (75MM)- PVC-5 |
| 64 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Y' Fitting without door (100MM)- PVC-6 |
| 65 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Single Tee without door (75MM)- PVC-7 |
| 66 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Single Tee without door (100MM)- PVC-8 |
| 67 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Single Tee with door 75MM- PVC-9 |
| 68 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Single Tee with door 100MM- PVC-10 |
| 69 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Bend with door (87.5°) 75MM- PVC-11 |
| 70 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Bend with door (87.5°) 110MM- PVC-12 |
| 71 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Clean Out Plug (COP) 75MM- PVC-13 |
| 72 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Clean Out Plug (COP) 110MM- PVC-14 |
| 73 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Reduced 'Y' Fitting without door 110mm x 75mm- PVC-15 |
| 74 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Reduced Tee with door 110mm x 75mm- PVC-16 |
| 75 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Coupler 75MM- PVC-17 |
| 76 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Vent Cowl 110MM- PVC-19 |
| 77 | Providing, fixing, jointing and testing , of PVC Multi Floor Trap without jali of minimum 50 mm water seal, making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge. 110mm x 75mm x 50mm/40mm (Toilet)- FLOOR TRAP-1 |
| 78 | Providing, fixing, jointing and testing , of PVC Nahani Trap without jali of minimum 50 mm water seal, making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge. 110mm x 75mm (Toilet & Kitchen)- FLOOR TRAP-2 |
| 79 | \\"Pressure Vessel Providing, fixing, testing and commissioning of pressure vessel for pressurization of fire system complete with valves at outlet / drain to operate as per operating sequences including 25 mm dia drain valve, air release valve with stop cock on the top, outside with one coat of primer & two coats of synthetic enamel paint of approved shade complete as required to operate commonly main fire pump, sprinkler pump & jockey pump at drop of pressure, automatically at required pressure setting. It should be complete as per manufacturer's specifications & as directed by Engineer- in-charge. working pressure:- 7 kg/sqcm test pressure: 10 kg/sqcm\\" (450 mm dia & 2000 mm height)- FF-1 |
| 80 | Providing & fixing of Anti vibration Expansion Bellow at pump inlet and outlet etc. as required. 200MM DIA- FF-2 |
| 81 | Providing & fixing of Anti vibration Expansion Bellow at pump inlet and outlet etc. as required. 150 mm dia.- FF-3 |
| 82 | Providing & fixing of Anti vibration Expansion Bellow at pump inlet and outlet etc. as required. 100 mm dia.- FF-4 |
| 83 | Providing & fixing of Anti vibration Expansion Bellow at pump inlet and outlet etc. as required. 80MM DIA- FF-5 |
| 84 | Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. (EXTERNAL WORKS) 100 mm dia.- FF-6 |
| 85 | Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. (EXTERNAL WORKS) 80 mm dia.- FF-7 |
| 86 | Providing & fixing of start/stop push buttons including complete connection etc. as required. (for terrace booster pump)- FF-8 |
| 87 | Providing & fixing of Anti vibration Expansion Bellow at pump inlet and outlet etc. as required. 100 mm dia.- FF-9 |
| 88 | Providing and fixing standard fire mans axe with heavy duty insulated rubber handle.- FF-10 |
| 89 | \\"Providing of FHC Door made of 16 gauge MS Sheet with frame of size 105x70mm complete door and frame assembly including all hardwares (Concealed Flush handle,Allen Key Lock, MS Hinges, 5mm Thick Float glass) & accesories . The door to be painted with fire resistance paint. The scope shall also include the painting of the frame with the same paint as the shutter or complete as per direction of Engineer-in-charge. (Approx. size of door: 900mm Wide & 1500mm Height)\\"- FF-11 |
| 90 | Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.-1 |
| 91 | Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.-2 |
| 92 | Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge.-3 |
| 93 | Supply, installation , testing & commissioning of XLPE insulated and PVC outer sheathed Aluminium conductor armoured cable of 1.1 KV grade confirming to IS : 7098:1988 (with upto date amendments) of following sizes. 3-1/2 core, X 120 sqmm.- ELECTRICAL-1 |
| 94 | Supply, installation , testing & commissioning of XLPE insulated and PVC outer sheathed Aluminium conductor armoured cable of 1.1 KV grade confirming to IS : 7098:1988 (with upto date amendments) of following sizes. 4 Core, X 6 sqmm.- ELECTRICAL-2 |
| 95 | Supplying and making end termination with brass compression gland & Al.lugs for following sizes of PVC insulated, PVC sheathed/ XLPE Al.conductor cables of 1.1 KV grade as required. 3-1/2 core, X 120 sqmm.- ELECTRICAL-3 |
| 96 | Supplying and making end termination with brass compression gland & Al.lugs for following sizes of PVC insulated, PVC sheathed/ XLPE Al.conductor cables of 1.1 KV grade as required. 4 Core, X 6 sqmm.- ELECTRICAL-4 |
| 97 | Supplying and laying control wiring with multicore copper stranded conductor of following sizes PVC insulated, PVC sheathed armoured cable between various sensors and system controller/starter etc.in pump house & out side on surface/existing cable tray complete with connections at both end with glands etc.as required 4 x 2.5 sq.mm- ELECTRICAL-5 |
| 98 | Supplying and laying control wiring with multicore copper stranded conductor of following sizes PVC insulated, PVC sheathed armoured cable between various sensors and system controller/starter etc.in pump house & out side on surface/existing cable tray complete with connections at both end with glands etc.as required 2 x 2.5 sq.mm- ELECTRICAL-6 |
| 99 | Supply and fixing in position 1 m wide Insulation mat made of elastomeric polymers Material (Class -A) of 415V grade as per IS 15642-2006 . Thickness of insulation mat shall be not less than 2 mm to withstand 1.1 KV dielectric strength AS PER IS 15652 : 2006. It should be complete as per specifications & directions of Engineer-in-charge. It should be complete as per specifications & directions of Engineer-in-charge.- ELECTRICAL-7 |
| 100 | Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required. 150 mm width x 50mm depth x 1.6 mm thickness.- ELECTRICAL-8 |
| 101 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable- CAT-6 |
| 102 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltag, 8 way , Double doorDSR 2025 E & M- 2.3.2 |
| 103 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted includin, 4 way (4 + 12), Double doorDSR 2025 E & M- 2.4.1 |
| 104 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted includin, 8 way (4 + 24), Double doorDSR 2025 E & M- 2.4.3 |
| 105 | DELETED, Single poleDSR 2025 E & M- 2.10.1 |
| 106 | DELETED, Double poleDSR 2025 E & M- 2.10.3 |
| 107 | DELETED, Triple pole and neutralDSR 2025 E & M- 2.10.5 |
| 108 | Supplying and fixing 40/63A rating, 415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of Four poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent.- MCB-1 |
| 109 | Supplying and installaton following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required., 150 mm width X 50 mm depth X 1.6 mm thicknessDSR 2025 E & M- 4.1.2 |
| 110 | Supplying and installaton following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required., 300 mm width X 50 mm depth X 1.6 mm thicknessDSR 2025 E & M- 4.1.4 |
| 111 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.DSR 2025 E & M- 5.4 |
| 112 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolDSR 2025 E & M- 5.9 |
| 113 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.DSR 2025 E & M- 5.15 |
| 114 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.DSR 2025 E & M- 5.18 |
| 115 | LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0 C to 40 0 C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching)DSR 2025 E & M- 8.3.2 |
| 116 | LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0 C to 40 0 C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching)DSR 2025 E & M- 8.3.3 |
| 117 | 85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0 C to 40 0 C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) 1.20 mm), 36 wattDSR 2025 E & M- 8.7.4 |
| 118 | SITC of 12W Extruded aluminium batten available in 2ft run length with multiple lumen packages and suitable for surface, wall & conduit ounting (with accessories). similar to Philips Type HSN Code- BN 021 LED12S 6500 PSU GR or equivalent.- BATTEN-1 |
| 119 | Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire having pressure diecast housing with driver set confirming to IP 65 and above Protection, IK08, High purity / transmisivity UV stablized Non yellowish diffuser/ Reflector for uniform light distribution, ditachable driver set, suitable for 24hrs continuous operation complete in all respect.-1200 system lumen, >120lm/W, PF>0.95, CRI>70, >300V, over voltage protection, 4KV internal surge protection with 5 year warrenty.- LED-1 |
| 120 | lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 0 C to 40 0 C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K, 18- 22 WattDSR 2025 E & M- 8.10.1 |
| 121 | \\"Supply of 300 mm exhuast fan having Built with a durable powder-coated metal body, this 300 mm exhaust fan brings both style and resilience to kitchens, bathrooms, or compact spaces. Equipped with a fast-spinning 1200 RPM motor, it swiftly eliminates steam, smoke, and odors for a fresher indoor atmosphere. The compact 300 mm sweep ensures a perfect wall or window installation without sacrificing airflow. Precision balanced metal blades deliver steady, powerful airflow while keeping vibrations and noise minimal. Designed to be energy-efficient, it uses approximately 48 W, offering strong performance without raising your electricity bill. Operates quietly around 40–45 dB, making it ideal for use near bedrooms, studies, or any quiet area. Comes with a sturdy steel bird guard to prevent insects and debris from entering, protecting hygiene and motor health. Featuring a corrosion-resistant finish, it stays looking fresh and functioning well even in humid conditions. Maintenance is hassle-free—blades and grill detach easily for quick cleaning to ensure consistent airflow.\\"- FAN-1 |
| 122 | Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value, delivery 210 CM/Min (Minimum) 1400mm, service value ≥ 6.0 CM/Min/Watt, airDSR 2025 E & M- 9.2.3 |
| 123 | Supply and fixing hexagonal Round G.P.fan box approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work.- DSR CIVIL 2023 10.18 |
| 124 | Supply Installation Testing and Commissioning of 400mm sweep 1500RPM energy efficient BLDC fan with double ball bearing for longer life similar to CGE RENESA or equivalent.- FAN-2 |
| 125 | Lightning Arrestor: Supply, installation, testing and commissioning of External Lightning wide area protection system based on Eaarly Streamer Emission (ESE) technology. Device shall emit electromagnetic impulse in the form of a streamer into the air microseconds earlier than naturally formed streamers. Device confirmg to NFC 17-102 and UNE 21186 Standards. Appropriate non penetrating mounting arrangement. The device shall be mounted at suitable clear to the highest point on the roof top. (Model selected shall give coverage of 79 M radius @ min 5M height from terrace)- LIGHTNING-1 |
| 126 | Down conductor:Supply, installation, testing and commissioning of 70 Sqmm twisted 19-Strand, bare Cu cable on surface/wall / as per site requirement and complete in all respect.- LIGHTNING-2 |
| 127 | Lightning Counter :Supply and installation of counting the number of lightning strikes without any power supply.- LIGHTNING-3 |
| 128 | Test Link :Supply and installation of test link in weather proof IP 65 BOX.- LIGHTNING-4 |
| 129 | Supply, installation, testing and commisioning of 2 x 25W LED Aviation abstruction light medium bay type 62, complete with lamp, lamp holder, Condenser necessary connecting wire, 1 X 25 AV with all necessary hardware, accessories as required for complete installation. Rate shall include the cost of necessary steel structures , fixing arrangements in this item. Refer drawing.- LIGHTNING-5 |
| 130 | Online UPS- Input supply: Three Phase, Output supply: Three Phase. Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 0 C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swapable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of modules required for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for, 10KVA (Each Power module shall be < 10 KVA)DSR 2025 E & M- 26.2.1 |
| 131 | SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 SWG CRCA sheet steel, complete with colour coded, heat shrinkable PVC insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. The panel shall be complete with name plate, earthing, numbering, danger plate etc. as per specifications and drawings as required. The panel shall withstand the fault level of 50kA as per Single Line Diagram. The Panel shall also be capable to communicate status like ON/OFF/ Trip through Modbus/Ethernet for major component like ACB, MCCB, MCB & Multifunation meters. The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have Buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Air Circuit Breakers,microprocessor release for overload, short circuit, instantaneous & earthfault protection with Current & Voltage metering & LCD display. Air Circuit Breaker with microprocessor release ge metering & LCD display , with ready to clsoe indicator, should have capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release with LSIG protection functionand should not derate upto 50 decree Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp ACB should have same frame size LCD display for fault trip history, haivng current limiting feature, double break mechanism & capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics) Main LT Panel INCOMING \\"2 Nos. 800 Amp EDO ACB 65KA LSIG having S/C, E/F O/C protection, R,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCB Inbuilt Zone Slelective Interlocking function Multifunction Meter\\" 1 Nos. 800 Amp 4P ATS BUSBARS 1 Nos. 1000 Amp FP busbars of aluminium alloy as per SLD. OUTGOING \\"5 Nos. 32 Amp FP MCB 10 KA On, Off, Trip Status Indication with control MCB Spare\\" \\"2 Nos. 63 Amp FP MCB 10 KA On, Off, Trip Status Indication with control MCB Spare\\" \\"5 Nos. 63 Amp FP MCCB 25 KA On, Off, Trip Status Indication with control MCB Multifunction Meter UPS Panel+External Light Feeder+Lift Spare\\" \\"5 Nos. 100 Amp FP MCCB 25 KA On, Off, Trip Status Indication with control MCB Multifunction Meter Floor Panel-F.F./S.F.+Plumbing+ Spare\\" \\"2 Nos. 250 Amp FP MCCB 25 KA On, Off, Trip Status Indication with control MCB Multifunction Meter Fire Fighting+ Spare\\" \\"1 Nos. 400 Amp TP MCCB 35 KA On, Off, Trip Status Indication with control MCB Multifunction Meter APFC Panel\\" \\"2 Nos. 630 Amp FP MCCB 50 KA On, Off, Trip Status Indication with control MCB Multifunction Meter HVAC Panel+ Spare\\" Short Circuit Breaking capacity should not less than 10 KA. RELAYS AS PER SLD- MAIN LT PANEL-1 |
| 132 | INCOMING \\"1 Nos. 100 Amp MCCB 25 KA LSIG having S/C, E/F O/C protection, R,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCB Inbuilt Zone Slelective Interlocking function Multifunction Meter\\" BUSBARS 1 Nos. 150 Amp FP busbars of aluminium alloy as per SLD. OUTGOING \\"2 Nos. 32 Amp FP MCB 10 KA On, Off, Trip Status Indication with control MCB Spare\\" \\"12 Nos. 32 Amp DP MCB 10 KA On, Off, Trip Status Indication with control MCB Room-1/2/3/4/5/6/7/8/9+ Common Area DB+Spare\\" Short Circuit Breaking capacity should not less than 10 KA. RELAYS AS PER SLD- MAIN LT PANEL-2 |
| 133 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :, 150 mm diaDSR 2025 E & M- 27.11.6 |
| 134 | Providing and fixing in position industrial type pressure gauges with gun metal / brass valves complete etc. as required.DSR 2025 E & M- 30.8 |
| 135 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required:, 2 way-100 mm dia M.S. PipeDSR 2025 E & M- 27.19.1 |
| 136 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required:, 4 way - 150 mm dia M.S. PipeDSR 2025 E & M- 27.19.2 |
| 137 | (a) Supplying, installation, testing and commissioning of electric driven terrace pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required. (c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class- 'F' insulation, conforming to IS-12615: 2018. (d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads., 450 lpm at 35 m Head CONTROL PANELSDSR 2025 E & M- 27.4.2 |
| 138 | INCOMING \\"1 Nos. 100 Amp MCCB 25 KA LSIG having S/C, E/F O/C protection, R,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCB Inbuilt Zone Slelective Interlocking function Multifunction Meter\\" BUSBARS 1 Nos. 150 Amp FP busbars of aluminium alloy as per SLD. OUTGOING \\"4 Nos. 63 Amp FP MCB 10 KA On, Off, Trip Status Indication with control MCB GYM+ MP Hall+ Cafe+Spare\\" \\"3 Nos. 32 Amp DP MCB 10 KA On, Off, Trip Status Indication with control MCB Common Area DB+Spare\\" Short Circuit Breaking capacity should not less than 10 KA. RELAYS AS PER SLD- MAIN LT PANEL-3 |
| 139 | UPS Panel INCOMING \\"1 Nos. 63 Amp MCCB 25 KA LSIG having S/C, E/F O/C protection, R,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCB Inbuilt Zone Slelective Interlocking function Multifunction Meter\\" BUSBARS 1 Nos. 100 Amp FP busbars of aluminium alloy as per SLD. OUTGOING \\"3 Nos. 32 Amp FP MCB 10 KA On, Off, Trip Status Indication with control MCB Server+Spare\\" \\"5 Nos. 32 Amp DP MCB 10 KA On, Off, Trip Status Indication with control MCB UPS DB-G.F./F.F./S.F.+Spare\\" Short Circuit Breaking capacity should not less than 10 KA. RELAYS AS PER SLD- MAIN LT PANEL-4 |
| 140 | Automatic Power Factor Correction (APFC) System Supply, Installation, testing and commissioning of Automatic Power Factor Correction (APFC) panel, indoor type floor mounted free standing totally enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %, 50 Hz AC System for Ambient temperature -5°C to +40°C, fabricated in compartmentalised designed made of CRCA sheet steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c cleaning & finishing complete with 9 tank process for powder coated of approved shade ( RAL 7032-Siemens Gray or as approved by Engineer-in-Charge), having front section (switch gear and control accessories) and rear section capacitor and reactor, front and rear access, having suitable current carrying capacity, extensible TPN Aluminium alloy bus bar of high conductivity, DMC/SMC bus bar supports, bottom base channel of MS Section, fabrication shall be done in transportable section, entire panel shall have common copper earth bar of minimum size of 25mm x 5mm with 2 nos. earth studs, the earth terminals provided on the body of capacitor bank shall also be bonded to the main capacitor panel earth bus with 2 nos. 8 SWG or 6 SWG GI earth wires/ equivalent size of copper conductor cable, forced ventilation for maintaining temperature rise not more than 5°C from ambient, interconnections, connections with 14% detuned reactor and heavy duty 525 V ISI marked Impregnated MPP(Metalized Polypropylene) Capacitor (IS 13340 Part -1 & 2) APFC Panel shall be in compliance with IS :16636 & CPWD Specifications etc. as per below details. (A) Incomers Suitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of TPN 50KA breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating Lamp set along with required Instruments and accessories with extended rotary handle and door interlocking arrangement. Current rating of the, 175 KVARDSR 2025 E & M- 25.1.6 |
| 141 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 10 sq. mm 4 core- CABLE-1 |
| 142 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sq. mm 4 core- CABLE-2 |
| 143 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 185 sq. mm 3-1/2 core- CABLE-3 |
| 144 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 300 sq. mm 3-1/2 core- CABLE-4 |
| 145 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade on Cable Tray as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PWD 2024-20d.1 16 sq. mm 4 core- CABLE-5 |
| 146 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade on Cable Tray as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PWD 2024-20d.1 25 sq. mm 3-1/2 core- CABLE-6 |
| 147 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade on Cable Tray as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PWD 2024-20d.1 70 sq. mm 3-1/2 core- CABLE-7 |
| 148 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade on Cable Tray as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PWD 2024-20d.1 185 sq. mm 3-1/2 core- CABLE-8 |
| 149 | Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade on Cable Tray as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PWD 2024-20d.1 300 sq. mm 3-1/2 core- CABLE-9 |
| 150 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required., 4 X 10 sq. mm (25mm)DSR 2025 E & M- 11.1.32 |
| 151 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required., 4 X 16 sq. mm (28mm)DSR 2025 E & M- 11.1.33 |
| 152 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required., 3½ X 25 sq. mm (28mm)DSR 2025 E & M- 11.1.20 |
| 153 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required., 3½ X 70 sq. mm (38mm)DSR 2025 E & M- 11.1.23 |
| 154 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required., 3½ X 185 sq. mm (57mm)DSR 2025 E & M- 11.1.27 |
| 155 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required., 3½ X 300 sq. mm (70mm)DSR 2025 E & M- 11.1.30 |
| 156 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required., 300 mm diaDSR 2025 E & M- 15.14.4 |
| 157 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required., 200 mm dia (OD-200 mm & ID-175 mm nominal)DSR 2025 E & M- 15.15.5 |
| 158 | Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,200A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following. a. 2 Nos. 11 mtr. long MS STEEL poles complete with, pole excavation, MS STEEL foundation, and back filling complete MS steel channel/angle iron etc. b. 1 Set of cross arms, branching, clamps and painting complete with GI nut, bolts & washers as required (for GO & DO), LA connection. c .1 set 11KV Insulator complete with spindles & hardware complete as required. d .1 No. 11KV 400A TP Gang operated Air break switches complete with 25mm dia GI pipe operating machanism, handle & locking arrangement. e. 1 set of 3 nos.11KV single pole drop out fuse complete with barrel fuses, and mounting arrangement. f. 1 set (3 nos.) 11KV lightning arrestor and connecting to all phases. g. 4 No. 150 mm dia 6 meter long GI pipe class 'B' (for XLPE cable protection) as required. h. 2 Set 50mm dia 3m long GI pipe earting with 25 x 6 mm GI earth strip complete as required (for GO & DO & LA) i 1 nos. 11KV HT danger boards and 2 set of anticlimbing devices. 11 KV Double Pole Structure described below- HT-1 |
| 159 | Supply of 3 core standered aluminium conductor XLPE (Cross linked polyethylene) insulated PVC bedded, Galvanised flat steel strip armoured cables confirming to I.S. 7098 (Part-II with latest amendments) II KV grade as per requirement. 240 sq. mm 3 core- HT-2 |
| 160 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required., Above 120 sq. mm and upto 400 sq. mmDSR 2025 E & M- 22.1.2 |
| 161 | Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required., Above 120 sq. mm and upto 400 sq. mmDSR 2025 E & M- 22.2.2 |
| 162 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required., Above 120 sq. mm and upto 400 sq. mmDSR 2025 E & M- 22.3.2 |
| 163 | Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :, 240 sq. mmDSR 2025 E & M- 23.5.3 |
| 164 | Supply and laying of PVC Insulated, FRLS Round Sheathed Multi Core Industrial Flexible Cable conforming to IS 694:2010 with Flexible Bright Annealed Copper Conductor for Voltage Grade 1100 Volts as per direction of engineer incharge. 10CX2.5Sq.mm- PVC INSULATOR-1 |
| 165 | Supply, erection, testing and commissioning of 1 panel, 630A ,11 kV, 3 Phase, 50 Hz., metal clad, dead front, 350 MVA rupturing capacity Vacuum Circuit Breaker Incoming & Outgoings as per the detailed specifications and drawings Outgoings as per the detailed specifications and drawings including connections etc. complete with following in-comers including connections etc. complete with following in-comers and out-goings including door interlocking panel should be expendable type complete as per technical specifications and as required. i) 1 No. VCB having following 1 No. 630A, 11kV, 3 Phase, 50Hz., metal clad, dead front, 350 MVA rupturing capacity, Fully Drawout type, Vacuum Circuit Breaker (VCB) 1 set of 11kV/110V Potential Transformers with MCB 1 Set of Phase indicating lamps with MCB 1 No. 0-11 kV Digital voltmeter with selector switch 1 set of indicating lamps to indicate OPEN, CLOSE, TRIP,SPRING CHARGED, TRIP CIRCUIT HEALTHY Push button for ON, OFF,TRIP&TRIP circuit healthy 1 set of 30/5-5A Current Transformer for metering and protection 1 No. 0-100 digital Amps ammeter with selector switch 1 Set of CDG 31 (2 No. O/C, 1 No. E/F) relay Digital frequency meter,Digital Tri vector meter. I Set of undervoltage relay and Overvoltage relay Trip circuit supervision relay,Auxiliary relays with shunt trip coil I No. Master Trip relay 1 No. Digital Power factor meter 1I/C + O/G Panel- HT PANEL-5 |
| 166 | Supplying, installation, testing and commissioning of following capacity (continuous loading) BEE 5 Star, 400KVADSR 2025 E & M- 24.9.4 |
| 167 | Supplying, Installation, Testing & Commissioning of ‘Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings: (A) Diesel Engine: Tourbocharged Diesel engine 4 stroke water cooled, multi cylinder, dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 40 0 C, 50% RH & at 1000 Meter MSL , capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, the Electronic governor shall be as per ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per CPWD specifications. (B) Engine mounted Instrument Panel fitted with and having digital dis Plate for following: (i) Start-stop switch with key (ii) Water temperature indication (iii) Lubrication oil pressure indication (iv) Lubrication oil temperature indication (v) Battery charging indication and Voltage indication (vi) RPM indication (vii) Over speed indication (viii) Low lubricantion Oil trip indication (ix) Engine Running Hours indication (x) Fuel Level, 400 KVADSR 2025 E & M- 29.1.14 |
| 168 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.DSR 2025 E & M- 2.21 |
| 169 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.DSR 2025 E & M- 5.6 |
| 170 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut boltDSR 2025 E & M- 5.8 |
| 171 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.DSR 2025 E & M- 5.12 |
| 172 | Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.DSR 2025 E & M- 5.14 |
| 173 | Supply installing testing & commissioning of out door type IP66 with additional canopy street light feeder pillar (Distribution Panel) compartmentalised design, dust tight & vermin proof made out of 14 gauge M.S. sheet, stove powder coated complete as required with following incomming & outgoing as per detail below. Incoming 63 Amp. 10 KA FP MCCB 1 No. Suitable digital contractor and timer for down & dusk 100 Amp. TPN Alu. Bus bar Outgoing 32 Amp. 10KA DP MCB 10 No. 32 Amp. 10KA FP MCB 2 No.- STREET LIGHT-1 |
| 174 | \\"Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. \\" 6 sq mm 2 Core- CABLE-10 |
| 175 | \\"Supply and Laying of Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade in Existing RCC/ Hume/ Metal pipe as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. \\" 16 sq mm 4 Core- CABLE-11 |
| 176 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required., 2 X 6 sq. mm (19mm)DSR 2025 E & M- 11.1.1 |
| 177 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required., 90 mm dia (OD-90 mm & ID-76 mm nominal)DSR 2025 E & M- 15.15.2 |
| 178 | Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.DSR 2025 E & M- 5.2 |
| 179 | Supply and fixing of decorative 8 to 16 Watt LED bollard luminairewith Base Plate made of powder coated die cast aluminium andextruded Al. housing with UV Stablized PC diffuser, SMD LEDs,Electronic driver set, confirming to IP 65/66 and IK 07 and aboveprotection, 600- 800mm height, complete in all respect.960-1920 system lumens, >120 Lm/W, PF>0.95, THD 300V Over Voltage protection, 4 KV internal SurgeProtection, with 5 years warrantee.- CAT- AAA PWD 2024 23.25- BOLLARD-1 |
| 180 | S & F 4 mtr. Decorative Pole for post top light & Base Cover complete as required. Make :- Havells- BOLLARD-2 |
| 181 | Supplying and fixing of decorative 40 Watt to 45 Watt, LED Post Top indirect light luminaire having Pressure die cast Aluminium body and UV Stablized PC/ Clear frosted glas cover, with driver set confirming to IP 66 and IK 08 protection, Potted driver( Not Circuitory) complete in all respect . 4800-5400 system lumens, >120 Lm/W, PF>0.95, THD70, >300V Over Voltage Protection andauto restart feature, 4 KV internal Surge Protection, with 5 years warrantee- CAT-AAA PWD 2024 23.26- POLE-1 |
| 182 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :, Kitchen sink with drain board, 510x1040 mm bowl depth 250 mm.DSR 2023- 17.10.1.1 |
| 183 | Providing and fixing Sink Mixer as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- Sink Mixer- GN-1 |
| 184 | Providing & Placing of Looking Mirror pasted on wall with the help of silicon having edges beveled, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- GN-2 |
| 185 | Providing and fixing Shower Arm as per the approved design all complete as per drawing, specification and direction of engineer incharge.Make-Jaquar/American Standard/Kerovit Eqivalent- GN-3 |
| 186 | Providing and fixing Overhead Shower as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Jaquar/American Standard/Kerovit Eqivalent- GN-4 |
| 187 | Providing and fixing Concealed Diverter with Cover Plate as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Jaquar/American Standard/Kerovit Eqivalent- GN-5 |
| 188 | Providing and fixing Bath Spout as per the approved design all complete as per drawing, specification and direction of engineer incharge.Make-Jaquar/American Standard/Kerovit Eqivalent- GN-6 |
| 189 | Providing & Fixing of Concealed Stop Cock With Trims as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-7 |
| 190 | Providing & Fixing of Floor Drainer as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-8 |
| 191 | Providing & Fixing of Wall hung Closet with Soft Close Seat Cover Fixed with Jumbo Bolts as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-9 |
| 192 | Providing and fixing Urinal With Sensor Make-Kerovit, as per the approved design all complete as per drawing, specification and direction of engineer incharge.- GN-10 |
| 193 | Providing and fixing Urinal Partition Make-Kerovit, as per the approved design all complete as per drawing, specification and direction of engineer incharge.- GN-11 |
| 194 | Providing & Fixing of Concealed Cistern With Push Plate as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-12 |
| 195 | Providing and fixing of Under Counter Basin as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-13 |
| 196 | Providing & fixing of Single Lever Basin Mixer as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Jaquar/American Standard/Kerovit Eqivalent- GN-14 |
| 197 | Providing and fixing 2 Way Bib Tap as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-15 |
| 198 | Providing & fixing Health Faucet as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-16 |
| 199 | Providing and fixing of Angle Cock as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-17 |
| 200 | Providing and fixing of Bottle Trap as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-18 |
| 201 | Providing and fixing of Toilet Paper Holder as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-19 |
| 202 | Providing and fixing of Towel Ring as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-20 |
| 203 | Providing and fixing of Soap Dispenser as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-21 |
| 204 | Providing and fixing of Waste Coupling as per the approved design all complete as per drawing, specification and direction of engineer incharge. Make-Kerovit/Equivalent- GN-22 |
| 205 | Providing and fixing of Long Braided Hos Pipe as per the approved design all complete as per drawing, specification and direction of engineer incharge.- GN-23 |
| 206 | Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20mm made of 0.5mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip intiles into spring 'T' with :, GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.DSR 2023- 12.54.2 |
| 207 | Providing and fixing and applying plaster of Paris (POP) false ceiling consisting of frame work made with 50mm sq. M.S tubes of 18 G thickness as main runners at 600 mm c/c both ways, suspended/ supported with M.S flats 25x4mm from existing R.C.C slab including providing and fixing expanded metal of size 5.25mm as per approved shade as per drawing & specification as approved by the Architect/ Engineer -in-Charge- POP-1 |
| 208 | \\"Providing and fixing in true horizontal level Cellio Open Cell Aluminium lay-in ceiling tiles with border panels forming flush-Tegular edge of size 600mmx600mm having Fire Performance Class A1 (EN13964). The tile of Black/ RAL Co-ordinated color with cell size 100mm X 100mm shall be laid on Black painted Armstrong Suprafine 38 of 15mm profile grid system comprising Main runners (3000mm), 1200mm and 600mm cross tees with 15mm white flanges and 38mm web height. The Tile shall be laid on Armstrong Suprafine 38 with 15mm wide T - section flanges color white having rotary stitching on all T sections i.e. the Main Runner with C3 coupling, 1200 mm & 600 mm Cross Tees with Hardened XL2 Clip having a web height of 38 mm and a load carrying capacity of 15.5 Kgs/M. The T Sections have a Galvanizing of 90 grams per M2 with pull out strength of 100 Kgs. INSTALLATION: To comprise main runner spaced at 1200mm centers securely fixed to the structural soffit by approved hangers at 1200mm maximum centre & not more than 150mm from spliced joints. The last hanger at the end of each main runner should not be greater than 600mm from the adjacent wall. 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long cross tees centrally between the 1200 mm cross tees. Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres. SUSPENSION SYSTEM - Anchor Fastener, Hanger Wire 2.5mm dia, Hook Clip with J Wire assembly. APPROVED MAKE - Armstrong/ HiSteel/Equivalent\\"-3500- PROVIDING-1 |
| 209 | Providing & fixing Armstrong Vertical Linear Baffle Ceiling made out of GI Extrusion in GI alloy grade. The baffle blade shall be in size of 100x 25 x 3600mm. The baffle blade shall be suspended using Slotted U-profile at on-center spacing in multiples of 25mm. longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. Installation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter. as per the approved design all complete as per drawing, specification and direction of Architect/ Engineer -in-Charge. APPROVED MAKE - Armstrong/ HiSteel/Equivalent- ARMSTRONG-1 |
| 210 | Providing and fixing of Engineered Wood flooring 15MM Thick range Solitary collection of Use 23/32 (Heavy Domestic/Domestic) with a Surface Abrasion Resistance of class AC3 (average 4500 cycles), Impact Resistance of IC2 (EN13329), Resistance to Cigarette Burn with a rating of 5 (EN 438-2:15), Swelling after 24 hrs in water of 15% (EN13329), Modulus of Rupture of 53.3 newton/mm2, Internal Bond 1.78 newton/mm2, Surface Soundness of 1.3 newton/mm2 (EN 13329:2000) with a 0.2mm thick wear layer on top of a High Density Fiber substrate core (density > 850 Kg/M3) of plank having Uni fit locking arrangement (lock strength > 1000 lbs/ft) with an underlayment made of natural colour foam , with accessories like End profile, Transition profile, reducer, etc. complete. The rate includes cost of all materials, accessories, labour, HOM, etc., complete at all levels. (The Shade, pattern etc., to be approved by Engineer in charge)Make-Mikasa/Luxe/Armstrong. all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Make-Armstrong,Mikasa,Luxe Equivalent MR- WOODEN FLOORING-1 |
| 211 | Providing & Fixing of 10MM Thick Rubber Sports Flooring Tiles having Anti Skid Surface & Weight Absorbtion capacity pasted with the help of Heatex Solution all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- RUBBER-1 |
| 212 | Providing and laying of Double Charged/GVT/PGVT floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1800x1200mm- DOUBLE-1 |
| 213 | Providing and laying of Double Charged/GVT/PGVT floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x1200mm- DOUBLE-2 |
| 214 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling/grouting and finishing complete as per direction of Engineer-in-charge., Size of Tile 600x600 mmDSR 2023- 11.48.2 |
| 215 | Providing & Making & Fixing of Commercial Wall Panneling made with Aluminium Section of 2\\"x1\\" @ 2'CC frame work cladded with 12MM Ply complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.-- PANNELING-1 |
| 216 | Providing & Making & Fixing of Wall Panneling made with 1MM Laminate & 5.5MM MDF on Existing Surface complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer-in-Charge.- WALL-1 |
| 217 | Providing & Making & Fixing of Wall Panneling made with 4MM Veneer & Teak Wood Mouldings as per design on Existing Surface & then Finished with Water Base PU Polish, as per the approved design all complete as per drawing, specification and direction as approved by Engineer-in-Charge.- WALL-2 |
| 218 | Providing and supplying Acoustical Wall Paneling with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and fire -resistant fabric with an option of colours as per the choice of the Architect/ Person in-charge of size as required providing a minimum sound absorption level to be affixed to wall using Wall panel impalers and construction adhesives as per the instructions laid down by the installer as per the approved design as approved by the Architect/ Engineer -in-Charge.- WALL-3 |
| 219 | Providing & Making & Fixing of Wall Panneling made with Coloured Lacquered Glass on Existing Surface complete with Melamine Polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- WALL-4 |
| 220 | Providing & Fixing of Designer Computer Numerical Control (CNC) Cutted Exterior Grade MDF Sheet which shall be Duco Painted & fixed on Existing Commercial Wall Panelling with the help of screw, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- COMPUTER-1 |
| 221 | Providing & Fixing of Wall Paper of approved shade as per drawing & specification as approved by Engineer -in-Charge.- WALLPAPER-1 |
| 222 | Providing & fixing of 32MM Flush Door complete with all Fittings Like Hinges, Mortis lock, Door closer, Tower Bolt etc all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- 32MM-1 |
| 223 | Providing, fabricating & placing single/Double leaf single swing aluminium stile door with 12mm thick toughened glass & stile. The door frame shall be formed with heavy duty aluminium door, fixed to dry wall partition. Rate to include providing & fixing of Branded make standard stainless steel brush finished hardwares Hinges: flush door hinge -Branded-. Finis: Std finish Handle & lock: lever handle & Mortise lock set with both side key cylinder- Branded, Door Closer: Exposed door closer Asymatric Rack and Pinion Door Closer with hold-open slide arm Closing force: 1-4 (adjustable) Tested according to EN 1154 for door width upto: 1100mm Door stopper: Half moon door stop Finish of profile- Black finish System.- LEAF-1 |
| 224 | Providing & Fixing of full height Single glazed partition using 10mm thick toughened Glass fixed with proprietary anodized aluminium sections on top, bottom, horizontal & vertical. Rate to include required accessories as per the manufacturer's specifications and shall be inclusive of all accessories like Gaskets. Glass to glass joints to be sealed with Double sided 2mm Thick transparent tape. The glasses to be butt jointed with 2 to 3mm edge chamfer & edge polishing all around.Achieving value of 31 dB. ( Rate is not included for door frames) Finish - Black Anodised, Partition Height - 2400mm. Glass - 10mm Toughened Glas.- FULL HEIGHT-1 |
| 225 | Providing & Fixing of Plotter Cutted Designer Film of approved shade as per drawing & specification as approved by Engineer -in-Charge.- PLOTTER-1 |
| 226 | Providing & Fixing of Plotter Cutted Designer Coloured Vinyl of approved shade as per drawing & specification as approved by Engineer -in-Charge.- PLOTTER-2 |
| 227 | Supply & Fixing of windows made from multi chambered UPVC profiles of minimum 60/108 mm thickness of (Wintech make or equivalent) in natural from stailized for heat, light, impact & UV radiation. The UPVC profiles should be reinforced with galzvanized steel profiles of designed thickness.Float glass of approved colour in 5 mm shall be fixed with heveled beads. All openable / sliding sashes shall be having grey/black colored weather seal fitted in continuous lenghts made from bubble PTV Rubber & side Hung with 90L openin friction syats of rust proof stainless steel with provision of multipoint lockng system (casement only) made from Espag rods (coated steel) all handle shall be made from die Cast zinc alloy in white finish only as per desigh, drawings, specification & as approved by Architect/Engineer Incharge.- WINDOW-1 |
| 228 | Providing & Fixing of Zebra Blinds with Hand Rail of approved shade as per drawing & specification as approved by Engineer -in-Charge.- ZEBRA-1 |
| 229 | Providing & Fixing of Desiner Curtains with Hand Rail of approved shade as per drawing & specification as approved by Engineer -in-Charge.- CURTAINS-1 |
| 230 | Providing & Fixing of Desiner Sheer Curtains with Hand Rail of approved shade as per drawing & specification as approved by Engineer -in-Charge.- DESINER-1 |
| 231 | Providing & Applying of Creative Painting by making wall Graphics with Exterior Acrylic Coloured Paints & Finishing the walls with Water PU Paint to give Long Lasting finish, as per the approved design all complete as per drawing, specification and direction of engineer incharge.- CREATIVE-1 |
| 232 | Providing & Fixxing of WPC Chaukat as per the approved design all complete as per drawing, specification and direction of engineer incharge- WPC-1 |
| 233 | Providing & Making & Fixing of Storage Cabinet made of 19mm board, having shelves & shutters & teak wood beading & finished surface of 1mm thick Laminate including all hardware like tower bolts, hinges, lock & handle as per approved drawing & direction of Engineer incharge.- CABINET-1 |
| 234 | Providing & Fixing of Rectangular Shape Polmer Planter of Size (375Wx375Dx400HT\\") With Thermocol Packing & Double Layer of Pabbles With Artificial 36 Plants of approved shade as per drawing & specification as approved by Engineer-in-Charge. MR-61- SHAPE-1 |
| 235 | Providing & Fixing of Round Shape Polmer Planter of Size (375DIA X 375HT\\") With Thermocol Packing & Double Layer of Pabbles With Artificial 36\\"Plants of approved shade as per drawing & specification as approved by Engineer-in-Charge. MR-62- ROUND-1 |
| 236 | Providing & Fixing of Signages Made of with 5/3mm Thick Acrylic if required UV Prints on Base Acrylic & Acrylic Letters, complete as per desigh, drawings, specification & as approved by Architect/Engineer Incharge.- SIGNAGES-1 |
| 237 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required., Group ADSR 2025 E & M- 1.10.1 |
| 238 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.DSR 2025 E & M- 1.25 |
| 239 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required., 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wireDSR 2025 E & M- 1.14.1 |
| 240 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required., 2 X 4 sq. mm + 1 X 4 sq. mm earth wireDSR 2025 E & M- 1.14.3 |
| 241 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required., 20 mmDSR 2025 E & M- 1.21.1 |
| 242 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required., 32 mmDSR 2025 E & M- 1.21.3 |
| 243 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required., 1 or 2 ModuleDSR 2025 E & M- 1.28.1 |
| 244 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required., 3 ModuleDSR 2025 E & M- 1.28.2 |
| 245 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required., 4 ModuleDSR 2025 E & M- 1.28.3 |
| 246 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required., 6 ModuleDSR 2025 E & M- 1.28.4 |
| 247 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required., 8 ModuleDSR 2025 E & M- 1.28.5 |
| 248 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required., 12 ModuleDSR 2025 E & M- 1.28.6 |
| 249 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.DSR 2025 E & M- 1.26 |
| 250 | Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non- Plenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required., 1 Run of cableDSR 2025 E & M- 39.18.1 |
| 251 | S&F of 125 Amp 4 pole MCCB (25 KA) Thermal Magnetic release- ELECTRICAL-9 |
| 252 | S & F surface/Flush mounting 8ways V TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge. CAT-A- V TPN distribution- ELECTRICAL-10 |
| 253 | S & F surface/Flush mounting 12ways V TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge. CAT-A- ELECTRICAL-11 |
| 254 | Supply and fixing of recess mounting round 15 TO 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT-AAA- ELECTRICAL-12 |
| 255 | Supply and fixing of 36 Watt to 46 Watt above 3300 leumin indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. CAT-AAA- ELECTRICAL-13 |
| 256 | Supply and fixing of 150mm Fresh Air Fan all complete as per drawing and specification and direction of engineer incharge. Make-Crompton/Bajaj/Havels Equivalent- ELECTRICAL-14 |
| 257 | Supply and fixing of 400mm Wall Fan all complete as per drawing and specification and direction of engineer incharge. Make-Crompton/Bajaj/Havels Equivalent- ELECTRICAL-15 |
| 258 | Supply & Fixing of LED Profile Light all complete as per drawing and specification and direction of engineer incharge. Make-Ledadvance/Ledos/Ledlum/Philips, Equivalent- ELECTRICAL-16 |
| 259 | Supply & Fixing of LED Profile Light Driver all complete as per drawing and specification and direction of engineer incharge. Make-Ledadvance/Ledos/Ledlum/Philips, Equivalent- ELECTRICAL-17 |
| 260 | Supply and Fixing of Deep Recess Mounting round 10 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. Make-Ledadvance/Ledos/Ledlum/Philips, Equivalent- ELECTRICAL-18 |
| 261 | Supply and Fixing of Deep Recess Mounting round 12.5 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. Make-Ledos-3890- ELECTRICAL-19 |
| 262 | Supply and Fixing of Deep Recess Mounting round 15 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. Make-Ledadvance/Ledos/Ledlum/Philips, Equivalent- ELECTRICAL-20 |
| 263 | Supply & Fixing of LED Wall Bracket Light Fitting & Drivers, all complete as per drawing and specification and direction of engineer incharge. Make-Imported- ELECTRICAL-21 |
| 264 | Supply & Fixing of LED Ceiling Chandlier Light Fitting & Drivers, all complete as per drawing and specification and direction of engineer incharge. Make-Imported- ELECTRICAL-22 |
| 265 | Providing & Fixing of 5KVA Online UPS Having 12V/26AH 15Nos Batteries & Battery Stand all complete as per drawing and specification and direction of engineer incharge. Make-Aeon- ELECTRICAL-23 |
| 266 | Providing & Fixing of Call Bell Chimes all complete as per drawing and specification and direction of engineer incharge. Make-L&T- ELECTRICAL-24 |
| 267 | Providing & Fixing of Modular plate type white RJ 45 CAT 6 Data/Talephone outlet / information outlets ETL verified to meet or exceed TIA / EIA category 6 requirements, universal wiring label permitting to either T568A or T568B, UL listed, for computer networking complete in all respect with cover plate, grid plate, screws, MS box, etc with connections as required with RJ-45 Data outlet- ELECTRICAL-25 |
| 268 | Providing & Fixing of Linear Hanging LED Light of Different Sizes Including Driver all complete as per drawing and specification and direction of engineer incharge. Make-Ledlum- ELECTRICAL-26 |
| 269 | Providing and Fixing of Reception/Counter Table Made of 19MM Ply Board Understructure. Front Modesty to be Made with 12MM Flexi Ply & Finished with 6MM Corian & All Outer & Inner Surface To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge.- FURNITURE-1 |
| 270 | Providing & Fixing, Table of Size - COLLABORATE 1500MM WITH SIDE STORAGE AND WITHOUT HEIGHT ADJUSTABLE EXTENSION MAIN TABLE - 1500W X 750D X 750HT COMPOSITE SIDE STORAGE - 1050W X 450D X 750HT The Collaborate 1500mm executive workstation is a thoughtfully designed compact desk setup ideal for modern office environments. The main desk measures 1500W x 750D x 750H mm and is crafted with a 25mm thick pre-laminated particle board tabletop, finished with 2mm PVC edge lipping to ensure long-term durability and impact resistance. The tabletop offers a clean and modern appearance suitable for executive and managerial spaces. The workstation is structurally supported by mild steel (MS) powder-coated loop legs, featuring a distinctive 55x55mm diamond profile. These are paired with die-cast metal connectors and reinforced with MS cross beams, ensuring superior strength and stability while adding a refined industrial aesthetic. A front modesty panel made of 18mm thick pre-laminated particle board with 2mm PVC edge lipping, and a standard height of 450mm, ensures privacy without compromising open design. For integrated electrical management, the desk features a 350mm wide metal flip-up cover with a soft closure mechanism, offering concealed access to switchboards and power/data outlets. The MS cable dump tray beneath the tabletop is designed to house switches and sockets efficiently. Additionally, a vertebra-type vertical wire manager (cable spine) is provided for seamless and organized cable routing from floor level to the desk, enhancing safety and aesthetic appeal. Accompanying the main desk is a composite side storage unit measuring 1050W x 450D x 750H mm, constructed from 18mm thick pre-laminated particle board for a consistent and coordinated look. This side unit offers a combination of closed storage and drawers for functional workspace organization. The configuration includes three drawers (2 box drawers + 1 file drawer) along with shuttered compartments, allowing versatile storage for office supplies, documents, and personal belongings. All shutters are equipped with auto-closing hinges to ensure smooth, silent operation. The drawers and shutters feature integrated finger groove handles for a clean, handle-less appearance, and the entire unit is fitted with a central locking system to ensure safety and security of stored materials. Adjustable shelves provide flexibility in internal space utilization, while levellers ensure stable placement even on uneven flooring. All essential hardware components are included, supporting ease of assembly and reliable daily usage.. Make-Featherlite / Geeken / Hof / Ferris/ Equivalent- FURNITURE-2 |
| 271 | Providing & Fixing, Medium Back Chair's is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood.Gaslift - Class 4 tested -ANSI BIFMA performance standards.Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002.The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength.Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards.Upholstery: Seat Cushion with pre moulded foam having leatherette tapestery of 50 - 60 density Density -- 52 kg/m3 Hardness -- 12.6kgf at 25%.Distinctively and characteristically designed tilt mechanism offering a very smooth and fluidic reclining motion with tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back support.Multilock mechanism is fabricated from CR Sheets, undergo through CO2 welding process imparting uniform surface finish and tensile strength. The components are processed with high degree of precision and care so as to assemble with other parts in perfect harmony to give smooth and effortless reclining experience. Tension springs are made out Grade II material conforming to Indian Standards. Also provided with release levers for locking mechanism and height adjustment of seat. Mechanism aides to operate the height adjustment, and has been equipped with 3 locking positions, back rest “ Return Prevention” function. Back Frame is inserted with leathertte tapestery cushion & Adjustable Lumbar Support.Tension control is below the Seat.Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable - Height Adjustable.Seat is duly upholstered with approved fabric. Chair will have adjustable headrestChair Should be BIFMA Certified.Seat: Depth- 51.5 cm Width- 44.5 cm Dimensions: Width- 51.5 cm Depth- 53.5 cm Minimum Height- 99.5 cm Maximum Height- 108.5 cm Minimum Seat Height- 44.5 cm Maximum Seat Height- 52.5 cm Width (Arm to Arm)- 66 MODEL, Chair should be BIFMA and Green Guard certified.:- AMAZE HB, Make-Featherlite/Geeken Equivalent.- FURNITURE-3 |
| 272 | Providing & Fixing, Fixed Leg Chair Made of The frame is made out of 25.4mm tube of 16 gauge tube confirming to IS-7138-1973, Welded by Co2 welding process for uniform surface finish and higher tensile strength perforation on the sheet is of uniform 2.5mm dimension and gives good ventilation.High quality hardware conforming to Hardness 38-44 and tensile strength – 1300 n/mm. IS 1363-1967.Seat is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Japanese T-nuts and riveted in to the plywood.Set and backUpholstery: Cushion with pre-moulded foam of 50 - 60kg/m3 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25%.Injection moulded polypropylene armrests.Leatherette cusion Back on Frame. Back is injected moulded PP.Seat and back are duly upholstered with approved Leatherette. AMAZE VA, Make-Featherlite / Geeken / Hof / Ferris/ Equivalent- FURNITURE-4 |
| 273 | Providing & Placing of Single Seater Sofa, Made of Wooden Base, Cushioned Foam & Leatherite Tapestry, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-5 |
| 274 | Providing & Placing of Two Seater Sofa, Made of Wooden Base, Cushioned Foam & Leatherite Tapestry, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-6 |
| 275 | Providing & Placing of Three Seater Sofa, Made of Wooden Base, Cushioned Foam & Leatherite Tapestry, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-7 |
| 276 | Providing & Placing of Four Seater Sofa, Made of Wooden Base, Cushioned Foam & Leatherite Tapestry, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-8 |
| 277 | Providing & Placing of Corner Sofa, Made of Wooden Base, Cushioned Foam & Leatherite Tapestry, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-9 |
| 278 | Providing & Placing of Easy Chair Made in teak wood As per design round shape having 100MM thick high density foam on seat & 50MM on back & sides upholstered with fabric, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-10 |
| 279 | Providing & Making & Fixing of Customized Peg Tables Made of Wooden & SS Structure all complete as per drawing and specification and direction of engineer incharge.- FURNITURE-11 |
| 280 | Providing & Placing of Corner Table Made in Teak Wood, 19MM Board & Veener as per design with Italian finished top, & melamine polish, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-12 |
| 281 | Providing & Making & Fixing of Customized Center Tables Made of Wooden & SS Structure all complete as per drawing and specification and direction of engineer incharge.- FURNITURE-13 |
| 282 | Providing & Placing of Dining Table :Size 1500x600x750MM made of teak wood legs & frame, 19MM board on Top with Marbel Finish Laminate. Teak wood polished in matching shade of mica in melamine finish, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-14 |
| 283 | Providing & Placing of Dining Table :Size 375MM Dia made of teak wood legs & frame, 19MM board on Top with Marbel Finish Laminate. Teak wood polished in matching shade of mica in melamine finish, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-15 |
| 284 | Providing & Placing of Dining Table :Size 600MM Dia made of teak wood legs & frame, 19MM board on Top with Marbel Finish Laminate. Teak wood polished in matching shade of mica in melamine finish, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-16 |
| 285 | Providing & Placing of Dining Chairs : as per design made of teak wood size 95cms high, seat 45cmx45cm, fully upholstered with approved fabric/leatherette, wood polished in melamine finish, all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. Customized- FURNITURE-17 |
| 286 | Providing and Fixing of Double Bed of Size (1950Lx1800W)MM Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge. Customized- FURNITURE-18 |
| 287 | Providing and Fixing of Bed Side Table of Size (600Lx300W)MM Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge. Customized- FURNITURE-19 |
| 288 | Providing and Fixing of Wardrobe of Size (900Lx600Wx2100HT)MM Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge. Customized- FURNITURE-20 |
| 289 | Providing and Fixing of Luggage Rack of Size (1200Lx600Wx600HT)MM Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge. Customized- FURNITURE-21 |
| 290 | Providing and Fixing of TV Unit of Size (1500Lx450Wx750HT)MM Made of 2 Layers of 19MM Board with All Edges to be Lipped with Teak Wood Beading & All Outside Exposed Surface To Be Finished With 4MM Veneer which shall be Melamine Polished & Inner Side To Be Finished with 1MM Laminate, Complete In All Respect As Per Drawing, Specification Approved By Architect/ Engineer In Charge. Customized- FURNITURE-22 |
| 291 | Supply of Modular Type outdoor units ,equipped with Highly Efficient Hermetically Sealed Scroll with back pressure control mechanism(Back pressure control minimised refrigeratant leakage at part load operation), all Inverter multiple Compressors in Each ODU, special heat exchanger, Y- branch as required, auto check function for connection error, auto address setting,Refrigerant temperature control and capacity as mentioned below. VRV/VRF System shall be suitable for working on 52 °C ambient temperature, Refrigerant R 410A. The outdoor units must have Variable Evaporting temperature function to automatically modulate the refriegerant temp from 6 deg C to 11 Deg C for energy efficiency. The Outdoor unit must have Free Phase Technology to ensure Continued Operation during Phase Reversal. Should have refrigerant cooled PCB for enhanced life of PCB. Auto refreigerant Charge to ensure optimum quantity of refrigerant charge & 6 pole motor for better efficiency in low RPM range(improves intermediate efficiancy). Compressor backup operation function if malfunction occure in compressor. Capacity control should be 7% to 100%. ODU high exernal static pressure up to 78.4Pa, ensuring the efficient heat dissipation and stable operation of equipment. The System should have IEER more than 15. ODU- 12 H.P (RXYQ12BRY16) VRV-α Heat Pump Series all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-1 |
| 292 | Supply of Modular Type outdoor units ,equipped with Highly Efficient Hermetically Sealed Scroll with back pressure control mechanism(Back pressure control minimised refrigeratant leakage at part load operation), all Inverter multiple Compressors in Each ODU, special heat exchanger, Y- branch as required, auto check function for connection error, auto address setting,Refrigerant temperature control and capacity as mentioned below. VRV/VRF System shall be suitable for working on 52 °C ambient temperature, Refrigerant R 410A. The outdoor units must have Variable Evaporting temperature function to automatically modulate the refriegerant temp from 6 deg C to 11 Deg C for energy efficiency. The Outdoor unit must have Free Phase Technology to ensure Continued Operation during Phase Reversal. Should have refrigerant cooled PCB for enhanced life of PCB. Auto refreigerant Charge to ensure optimum quantity of refrigerant charge & 6 pole motor for better efficiency in low RPM range(improves intermediate efficiancy). Compressor backup operation function if malfunction occure in compressor. Capacity control should be 7% to 100%. ODU high exernal static pressure up to 78.4Pa, ensuring the efficient heat dissipation and stable operation of equipment. The System should have IEER more than 15. ODU- 16 H.P (RXYQ16BRY16) VRV-α Heat Pump Series all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-2 |
| 293 | Supply of Modular Type outdoor units ,equipped with Highly Efficient Hermetically Sealed Scroll with back pressure control mechanism(Back pressure control minimised refrigeratant leakage at part load operation), all Inverter multiple Compressors in Each ODU, special heat exchanger, Y- branch as required, auto check function for connection error, auto address setting,Refrigerant temperature control and capacity as mentioned below. VRV/VRF System shall be suitable for working on 52 °C ambient temperature, Refrigerant R 410A. The outdoor units must have Variable Evaporting temperature function to automatically modulate the refriegerant temp from 6 deg C to 11 Deg C for energy efficiency. The Outdoor unit must have Free Phase Technology to ensure Continued Operation during Phase Reversal. Should have refrigerant cooled PCB for enhanced life of PCB. Auto refreigerant Charge to ensure optimum quantity of refrigerant charge & 6 pole motor for better efficiency in low RPM range(improves intermediate efficiancy). Compressor backup operation function if malfunction occure in compressor. Capacity control should be 7% to 100%. ODU high exernal static pressure up to 78.4Pa, ensuring the efficient heat dissipation and stable operation of equipment. The System should have IEER more than 15. ODU- 20 H.P (RXYQ20BRY16) VRV-α Heat Pump Series all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-3 |
| 294 | Supply of Modular Type outdoor units ,equipped with Highly Efficient Hermetically Sealed Scroll with back pressure control mechanism(Back pressure control minimised refrigeratant leakage at part load operation), all Inverter multiple Compressors in Each ODU, special heat exchanger, Y- branch as required, auto check function for connection error, auto address setting,Refrigerant temperature control and capacity as mentioned below. VRV/VRF System shall be suitable for working on 52 °C ambient temperature, Refrigerant R 410A. The outdoor units must have Variable Evaporting temperature function to automatically modulate the refriegerant temp from 6 deg C to 11 Deg C for energy efficiency. The Outdoor unit must have Free Phase Technology to ensure Continued Operation during Phase Reversal. Should have refrigerant cooled PCB for enhanced life of PCB. Auto refreigerant Charge to ensure optimum quantity of refrigerant charge & 6 pole motor for better efficiency in low RPM range(improves intermediate efficiancy). Compressor backup operation function if malfunction occure in compressor. Capacity control should be 7% to 100%. ODU high exernal static pressure up to 78.4Pa, ensuring the efficient heat dissipation and stable operation of equipment. The System should have IEER more than 15. ODU- 22 H.P (RXYQ22BRY16) VRV-α Heat Pump Series all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-4 |
| 295 | Supply of Ductable Type Unit- 2.08TR + Cordless Remote + Refnet, Model FXMQ63ARV16 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-5 |
| 296 | Supply of Round Flow Cassette Type Unit- 2.65TR + Cordless Remote + Refnet, Model FXFSQ80 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-6 |
| 297 | Supply of Round Flow Cassette Type Unit- 3.31TR + Cordless Remote + Refnet, Model FXFSQ100 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-7 |
| 298 | Supply of Round Flow Cassette Type Unit- 4.63TR + Cordless Remote + Refnet, Model FXFSQ140 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-8 |
| 299 | Supply of TFA Ductable Type Unit- 4.13TR + Cordless Remote + Refnet, Model FXMQ125NFRV16 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-9 |
| 300 | Supply of TFA Ductable Type Unit- 6.62TR + Cordless Remote + Refnet, Model FXMQ125NFRV16 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-10 |
| 301 | Supply of Ductable Type Unit- 8.5TR + Cordless Remote + Refnet, Model FDR100FRV16 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-11 |
| 302 | Supply of Split Type Unit- 1.0TR + Cordless Remote + Refnet, Model FTKC35 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-12 |
| 303 | One Time Lifting, shifting, positioning, installation, testing of indoor units, outdoor units, fittings (Imported Y-joints & header etc.) remote controls of indoor units, complete as per specification and drawings, all complete as per drawing, specification and direction as approved by Engineer -in-Charge. OUTDOOR UNITS- AC-13 |
| 304 | One Time Lifting, shifting, positioning, installation, testing of indoor units, outdoor units, fittings (Imported Y-joints & header etc.) remote controls of indoor units, complete as per specification and drawings, all complete as per drawing, specification and direction as approved by Engineer -in-Charge. SPLIT UNITS- AC-14 |
| 305 | One Time Lifting, shifting, positioning, installation, testing of indoor units, outdoor units, fittings (Imported Y-joints & header etc.) remote controls of indoor units, complete as per specification and drawings, all complete as per drawing, specification and direction as approved by Engineer -in-Charge. INDOOR CASSETTE UNITS- AC-15 |
| 306 | One Time Lifting, shifting, positioning, installation, testing of indoor units, outdoor units, fittings (Imported Y-joints & header etc.) remote controls of indoor units, complete as per specification and drawings, all complete as per drawing, specification and direction as approved by Engineer -in-Charge. INDOOR DUCTABLE UNITS- AC-16 |
| 307 | Supply of Outdoor Unit Connection Kit For 2Nos Outdoor Unit - BHFP22P1006 all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-17 |
| 308 | Supply of Daikin Gas Joint all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-18 |
| 309 | Commissioning of VRV systems including topping R410A gas per site requirements all complete as per drawing, specification and direction as approved by Engineer -in-Charge.-1500.001- AC-19 |
| 310 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 41.3 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-20 |
| 311 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 34.9 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-21 |
| 312 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 28.6 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-22 |
| 313 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 22.2 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-23 |
| 314 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 19.1 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-24 |
| 315 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 15.9 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-25 |
| 316 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 12.7 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-26 |
| 317 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 9.5 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-27 |
| 318 | Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported 6.4 mm all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-28 |
| 319 | Providing & Laying of Cable tray for copper pipe 300MM all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-29 |
| 320 | Providing & Laying of Cable tray for copper pipe 200MM all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-30 |
| 321 | Supply, Installation, testing and commissioning of Hard PVC Pipe Suitable for 10 Kg/cm2 water pressure including fittings such as elbow, socket, reducer, etc.insulated with 6 mm thick tubular nitrile insulation, 32 mm dia with 6 MM thickness all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-31 |
| 322 | Supply, Installation, testing and commissioning of Hard PVC Pipe Suitable for 10 Kg/cm2 water pressure including fittings such as elbow, socket, reducer, etc.insulated with 6 mm thick tubular nitrile insulation, 25 mm dia with 6 MM thickness all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-32 |
| 323 | Nitrogen Flushing & Leak Check for all Refrigerant pipes etc all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-33 |
| 324 | Supply & Fixing of Outdoor Stand all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-34 |
| 325 | Providing & fixing control cum transmission wiring of copper in suitable conduits between indoor and out door unit all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-35 |
| 326 | Supply & Laying of M S Slotted Angle for pipes and cables horizontaly and vertically along with threaded rod, nut, bolt, saddle, tie etc all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-36 |
| 327 | Wall Chaseing as per site requirement all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-37 |
| 328 | Making Core cutting in Walls, Beams, RCC structure as per site requirement all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-38 |
| 329 | Supplying, installing, testing and commissioning Galvanized sheet steel ( GSS) ducting of following thickness including necessary supports, hangers, nut, bolts, gasket, split dampers, 0.63 mm (24 SWG) galvanized sheet steel all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-39 |
| 330 | Supplying, installing, testing and commissioning Galvanized sheet steel ( GSS) ducting of following thickness including necessary supports, hangers, nut, bolts, gasket, split dampers, 0.63 mm (22 SWG) galvanized sheet steel all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-40 |
| 331 | Supplying and fixing of external thermal insulation on ducts with Closed Cell Elastomeric Nitrile Rubber Foam (Class - O, Fire retardent) 9MM all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-41 |
| 332 | Supplying and fixing accaustic lining with 25mm thick resin bonded fiber glass of density 32 kg/cum on the inner side of ducting including flexing RP tissue paper finished with 30 G perforted aluminium sheet all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-42 |
| 333 | Supplying and fixing of powder coated aluminium section supply air diffusers/ grill with fixed air distribution grid all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-43 |
| 334 | Supplying and fixing of MS Valume control damper for supply air all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-44 |
| 335 | Supplying and fixing of Canvas Connection For Ductable Units all complete as per drawing, specification and direction as approved by Engineer -in-Charge.- AC-45 |
| 336 | Supply, Installation, Testisng & Commissioning of IP POE Dome fixed Cameras, Network TDN IR Indoor/Outdoor Camera, 1/3\\" CMOS, 2 MP, 3.6 mm Fixed, 24 IR LEDs, PoE, H.264 complete. Make - Dahua- CAMERA-1 |
| 337 | Supply, Installation, Testisng & Commissioning of IP POE 2MP, 25X Zoom PTZ Camera, Network TDN IR Indoor/Outdoor Camera, 1/3\\" CMOS, 2 MP, 3.6 mm Fixed, 24 IR LEDs, PoE, H.264 complete. Make - Dahua- CAMERA-2 |
| 338 | Supply, Installation, testing and commissioning of 32 VMS channel NVR with Embedded enterprise grade linux processor, real-time H.265 Security baseline 2.1, 1080p@30 fps adaptive decoding, ONVIF and RTSP protocols, resolution HDMI 4K, AI Face detection, perimeter protection, IVS, people counting, heat map, and SMD, BW 160 Mbps, Audio PCM/G711A/G726/AAC, privacy masking, video loss, scene changing, PIR alarm, SATA III port up to 10 TB. Make Dahua/HikVision- CAMERA-3 |
| 339 | Supply, Installation, Testisng & Commissioning of 6TB SATA Internal with 1M hours MTBF, 180 TB workload rate, write-intensive, low bit-rate, high stream-count, prioritized write-op. Make - WD- CAMERA-4 |
| 340 | Supply, Installation, testing and commissioning of HDBaseT Hdmi Extender Make - Milestone/Bluestream- CAMERA-5 |
| 341 | Providing, Installation, Testing & Commissioning of Hig Performance 1.4a standard HDMI 4K Cable. Make - Extron/Nedis/Logic/DC- CAMERA-6 |
| 342 | Supply, Installation, testing and commissioning of wall mountable 55\\" high resolution LED monitor with HDMI port and commercial series suitable for 12x7 operation. All accessories for installation including wall mounting stand/ bracket. Make - Samsung/Sony- CAMERA-7 |
| 343 | Supply, Installation, testing and commissioning of Carrier-Grade IP Phones, 2-line model, zero-touch provisioning, 5-way voice conferencing, integrated PoE. Make - Grandstream- TELEPHONE-1 |
| 344 | Supply, Installation, testing and commissioning of Carrier-Grade IP Phones, 6-line model, 4.3 inch color LCD screen, zero-touch provisioning, 5-way voice conferencing, integrated PoE. Make - Grandstream- TELEPHONE-2 |
| 345 | Supply, Installation, testing and commissioning of ipbx with powerful & scalable unified communication & collaboration. Supports 1000 Users, 100 Concurrent Calls, Voice Conference, 8 Analog Telephone FXS Port, 8 PSTN Line FXO Port, 1 USB 3.0 Port and 1 USB2.0 Port 1 SD Card Slot. Make - Grandstream- TELEPHONE-3 |
| 346 | Supply, Installation, Testing & Commissioning of 42U Rack Make - Dlink/Comrack- WIFI-1 |
| 347 | Supply, Installation, Testing & Commissioning of Rack accessories Make - Dlink/Comrack- WIFI-2 |
| 348 | Supply, Installation, Testing & Commissioning of Cat 6 patch panel, loaded. Make - Dlink- WIFI-3 |
| 349 | Supply, Installation, Testing & Commissioning of modular patch cables 1m 10/100/1000 Make - AMP/Molex/DC- WIFI-4 |
| 350 | Supply, Installation, Testing & Commissioning of 24 port POE switch 10/100/1000. Make - Dlink/Netgear-63796- WIFI-5 |
| 351 | Supply, Installation, Testing & Commissioning of Dual Band Wave Wifi 6 Access Points. Make - Grandstream/Netgear- WIFI-6 |
| 352 | Supply, Installation, Testing & Commissioning of LB VPN Gateway . Make - Grandstream- WIFI-7 |
| 353 | Supply, Installation, Testing & Commissioning of 1G SFP Trunking Module . Make - Dlink/Syrotec/Mikrotik- WIFI-8 |
| 354 | Supply, Installation, Testing & Commissioning of OFC Patch Cable. Make - Dlink/Syrotech- WIFI-9 |
| 355 | Supply, Installation, Testing & Commissioning of XL Series efficient Amplifier built for demanding commercial sound applications, highly efficient. Make - JBL Crown- PA-1 |
| 356 | Supply, Installation, Testing & Commissioning of 2 Way in celing ohigh-fidelity loudspeaker, High Sensitivity74 Hz – 20 kHz, 25W 70V / 100V Distributed Lines. Make - JBL/Russound- PA-2 |
| 357 | Supply, Installation, Testing & Commissioning of Digital sound processing system or install high performance sound application, AEC & Auto EQ. Make AT- PA-3 |
| 358 | Supply, Installation, Testing & Commissioning of Network Multi Smart Player with Zoning, BT, USB, SMB and Airplay capability. Make - Arylic/Russound- PA-4 |
| 359 | Supply, Installation, Testing & Commissioning of Interconnects & Connectors. Make - Custom- PA-5 |
| 360 | Supply, Installation, Testing & Commissioning of Heavy Duty Oxygen Free Speaker Cable. Make ProEL/PT/ASN/Krystal- PA-6 |
| 361 | Supply, Installation, Testing & Commissioning of XL Series efficient Amplifier built for demanding commercial sound applications, highly efficient. Make - JBL Crown- PA-7 |
| 362 | Supply, Installation, Testing & Commissioning of 2 Way in celing ohigh-fidelity loudspeaker, High Sensitivity74 Hz – 20 kHz, 25W 70V / 100V Distributed Lines. Make - JBL/Russound- PA-8 |
| 363 | Supply, Installation, Testing & Commissioning of 15\\" Subwoofer, Freq range 35-100 Hz, 2000W power. Make - JBL- PA-9 |
| 364 | Supply, Installation, Testing & Commissioning of Network Multi Smart Player with Zoning, BT, USB, SMB and Airplay capability. Make - Arylic/Russound- PA-10 |
| 365 | Supply, Installation, Testing & Commissioning of Interconnects & Connectors. Make - Custom- PA-11 |
| 366 | Supply, Installation, Testing & Commissioning of Heavy Duty Oxygen Free Speaker Cable. Make ProEL/PT/ASN/Krystal- PA-12 |
| 367 | Supply, Installation, testing and commissioning of Rack Accessories For 27U Rack Make - Dlink/Comrack-15279- PA-13 |
| 368 | Supply, Installation, testing and commissioning of Metal Shelf Rack Make - Dlink/Comrack-4895- PA-14 |
| 369 | Supply, Installation, Testing & Commissioning of XL Series efficient Amplifier built for demanding commercial sound applications, highly efficient. Make - JBL Crown- PA-15 |
| 370 | Supply, Installation, Testing & Commissioning of 2 Way Two-Way 5.25 inch (135mm) Coaxial Mushroom Landscape Speaker. Make - JBL/Russound- PA-16 |
| 371 | Supply, Installation, Testing & Commissioning of Network Multi Smart Player with Zoning, BT, USB, SMB and Airplay capability. Make - Arylic/Russound- PA-17 |
| 372 | Supply, Installation, Testing & Commissioning of Interconnects & Connectors. Make - Custom- PA-18 |
| 373 | Supply, Installation, Testing & Commissioning of Heavy Duty Oxygen Free Speaker Cable. Make ProEL/PT/ASN/Krystal- PA-19 |
| 374 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.DSR 2023- 25.1 |
| 375 | Finishing walls with textured exterior paint of required shade :, New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm.DSR 2023- 13.45.1 |
| 376 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approvedshop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.DSR 2023- 8.32 |
| 377 | Providing & Fixing of Stainless Steel Finish Acrylic Backlight Logo of Community Center In English & Hindi complete as per desigh, drawings, specification & as approved by E/I.- BUILDING FACADE-1 |
| 378 | Providing & Fixing of Cluster Stone Brick Stamping of having Super Hard outer shell on Vertical Surface with uncoloured Adhesive FS complete as per desigh, drawings, specification & as approved by Architect/Engineer Incharge.- BUILDING FACADE-2 |
| 379 | Providing & Fixing of 6MM Thick High Pressure compact Laminate made out of thermosetting resign treated Kraft as core material and design paper as a finish surface. Compact laminates should be resistance to water immersion through permissible increase on thickness and mass 1.35kg/cm3 . Compact should be flame retardant fulfilled the criteria of under BS-476/97 and EN438-6 with classification of BS1D0 standard property with Anti-bacterial & Anti-termite (under JIS Z2801:2000 certification), Chemical resistance, Scratch resistant ,flame resistance, weather & climatic shock resistance(The manufacturer should provide10 years warranty certification on any manufacturing and moisture related defects.), and fulfilled the criteria of Green Guard Gold certification and manufactured under EN438-2&3:2005 standard complete as per desigh, drawings, specification & as approved by Architect/Engineer Incharge.- BUILDING FACADE-3 |
| 380 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge., All kinds of soilDSR 2023- 2.6.1 |
| 381 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re- olling the sub grade and disposal of surplus earthwith lead upto 50 metres.DSR 2023- 16.1 |
| 382 | Providing & laying of a separation membrane between the concrete slab & the sub-base of impermeable plastic sheet 125 microns thick laid flat without creases. Overlap of plastic sheet is necessary and should be 300mm. The separation membrane is to be stuck to the lower lvl. with patches of adhesives or concrete nails with washer. (M.R.)- MEMBRANE-1 |
| 383 | Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber,finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note: Cement content considered in M-30 is @ 340Kg/Cum. Excess/Less cement used as per design mix is payable, recoverable separately., Cement concrete prepared with batch mixing machine.DSR 2023- 16.43.1 |
| 384 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement., 12 mm cement plasterDSR 2023- 13.9.1 |
| 385 | Trimixing on surface (M.R.)- TRIMIXING-1 |
| 386 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge., Using grade 'A' sealing compound conforming to IS: 1834.DSR 2023- 16.46.1 |
| 387 | Open timbering in trenches including strutting and shoring complete (measurements to be taken of the face area timbered):, Open timbering in trenches including strutting and shoring complete (measurements to be taken of the face area timbered): Depth not exceeding 1.5 m.DSR 2023- 2.20.1 |
| 388 | Open timbering in trenches including strutting and shoring complete (measurements to be taken of the face area timbered):, Depth exceeding 1.5 m but not exceeding 3 m.DSR 2023- 2.20.2 |
| 389 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :, 150 mm dia. R.C.C. pipeDSR 2023- 19.6.2 |
| 390 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :, 150 mm diameter S.W. pipeDSR 2023- 19.3.2 |
| 391 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :, Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5DSR 2023- 19.7.1.1 |
| 392 | Extra for depth for manholes, Size 90x80 cm, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5DSR 2023- 19.8.1.1 |
| 393 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :, Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 1 16 kg (weight of cover 58 kg and weight of frame 58 kg) :, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5DSR 2023- 19.7.2.1 |
| 394 | Extra for depth for manholes, Size 120x90 cm, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5DSR 2023- 19.8.2.1 |
| 395 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work, 65 mm dia. nominal boreDSR 2023- 18.12.7 |
| 396 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work, 50 mm dia. nominal boreDSR 2023- 18.12.6 |
| 397 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work, 25 mm dia. nominal boreDSR 2023- 18.12.3 |
| 398 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :, 65 mm nominal boreDSR 2023- 18.17.5 |
| 399 | Providing and fixing gun metal non- return valve of approved quality (screwed end) :, 65 mm nominal bore, HorizontalDSR 2023- 18.19.5.1 |
| 400 | Providing and fixing gun metal non- return valve of approved quality (screwed end) :, 50 mm nominal bore, HorizontalDSR 2023- 18.19.4.1 |
| 401 | Providing and fixing gun metal non- return valve of approved quality (screwed end) :, 25 mm nominal bore, HorizontalDSR 2023- 18.19.1.1 |
| 402 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.l. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:, With common burnt clay F.P.S.(non modular) bricks of class designation 7.5DSR 2023- 18.33.1 |
| 403 | Supply, Installation, testing & commissioning of Vertical in line pumping set complete. The rate shall include the cost of electrical panel and piping work complete Domestic Water Supply pumps : Capacity/Flow Rate - 12.5 m3/hr Head - 45 m Location - 1 set in UGT (1 set = 2nos(1W+1S))- PUMPSET-1 |
| 404 | Supply, fixing, testing and commissioning of Level Float Switch, for dry run protection of pump as per specifications:- Lehry Make Level Float Switch 1) Body : Polypropylene, Highly Durable, Water Proof 2) Rating : IP68 3) Temperature : 0-50DegC 4) Cable : PVC Size 5 Mtr, Item Code (LIV-LFV-RED- MTR) (location : UG TANK)- PUMPSET-2 |
| 405 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:, Cement mortar 1:4 (1 cement : 4 coarse sand)DSR 2023- 6.1.1 |
| 406 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :, 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)DSR 2023- 5.1.2 |
| 407 | Centering and shuttering including strutting, propping etc. and removal of form for :, Suspended floors, roofs, landings, balconies and access platformDSR 2023- 5.9.3 |
| 408 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level., Mild steel and Medium Tensile steel barsDSR 2023- 5.22.1 |
| 409 | 12 mm cement plaster finished with a floating coat of neat cement of mix :, 1:3 (1 cement: 3 fine sand)DSR 2023- 13.7.1 |
| 410 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :, With 20x20 mm square barDSR 2023- 19.15.1 |
| 411 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality, M D - 10, Circular shape 500 mm internal diameterDSR 2023- 19.19.2.2 |
| 412 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level., All types of soil, 300 mm diaDSR 2023- 23.2.1.1 |
| 413 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge., 150 mm nominal size diaDSR 2023- 23.4.2 |
| 414 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.DSR 2023- 23.5 |
| 415 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.DSR 2023- 23.6 |
| 416 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge.DSR 2023- 23.7 |
| 417 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in-charge.DSR 2023- 23.8 |
| 418 | Constructing brick masonry INSPECTION chamber 60x60x75 cm with bricks of class designation 50 in cement mortar 1:4 (1 cement : 4 coarse sand) including CI cover with frame LIGHT WEIGHT complete as per design. With FPS bricks- CHAMBER-1 |
| 419 | Constructing brick masonary open surface drain with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 fine sand) including earth excavation, 10cm thick bed concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and 25mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) for filling haunches including 12mm cement plaster 1:4 (1 cement : 4 coarse sand ) with a floating coat of neat cement inside the drain, its top and exposed side including disposal of surplus earth complete as per standard design: Drain 300 wide average. Depth 45 cm with R.C.C. slab- CHAMBER-2 |
| 420 | Supply, installing, testing and commissioning of non clog submersible type drainage / dewatering pumpset \\"Product Type: SUBMERSIBLE DRAINAGE PUMP Product Configuration Pump Classification: Standard Pump Component Materials Volute Material: Cast Iron FG 260 Impeller Material: Cast Iron FG 260 Shaft Material: S.S AISI 410 Seal Material: Carbon/Ceramic/NBR/S.S 304 Motor Specifications Phase: 3 Voltage: 380-415V Cable Length: Standard - 5 metres Cable Length: Additional - 0 metres: 0 Pipework Connection Float Switch: With Float Switch Solids Diameter Limit Maximum Solids Diameter: 10 mm Flow Rate = 205 LPM Each Pump Head = 9m Each Pump Set Detail = 1W+1S ( FOR EXTERNAL)\\"- CHAMBER-3 |
| 421 | Transportation Charges of drilling equipment including assembly and other material as required.- BORING-1 |
| 422 | Drilling of 675 mm. dia by rotary machine- BORING-2 |
| 423 | Supply & laying of 350 mm. dia housing pipe (8 mm. thick)- BORING-3 |
| 424 | Supply & laying of 200 mm. dia blind pipe (8 mm. thick)- BORING-4 |
| 425 | Supply & laying of 200 mm. dia slotted pipe (8 mm. thick)- BORING-5 |
| 426 | Supply & fixing of 350 mm. dia Socket- BORING-6 |
| 427 | Supply & fixing of 200 mm. dia Socket- BORING-7 |
| 428 | Supply & fixing of 200 mm. dia Bail plug- BORING-8 |
| 429 | Supply & fixing of 350 mm. dia well cap- BORING-9 |
| 430 | Supply & fixing of 350x200 mm. dia reducer.- BORING-10 |
| 431 | Supply & fixing of 350 mm. dia housing clamp- BORING-11 |
| 432 | Supply & Filling of pee gravel 2 mm. 4 mm. in side of bore after lower and development as required as per direction of E/I.- BORING-12 |
| 433 | Development by air compressor including Transportation.- BORING-13 |
| 434 | Development by O.P. Unit including Transportation.- BORING-14 |
| 435 | Supply of submersible pump suitable for tube well capable of pumping clear and cold water free from chemical and directly coupled with electric moter operating of 415 volt suitable for 3 phase 50 cycle A.C. Supply of following duty condition: A - Discharge of water in LPM 860 Approx size of discharge outlet in 80 mm. B - Total Head of pump set 45 m.- BORING-15 |
| 436 | Supply and fixing of finolex or equivalent ISI marked submersible copper cable of size 2x3x2.5 sq. mm.- BORING-16 |
| 437 | Supply of control panel cubical type wall mounted vermin proof with internal wiring duly enameled painted and mechanically finished having L&T of qul. Male switch fuse unit with HRC fuses, Ameter, Boltmeter, Selector switch, phase indicating lamp with bulbs, instrument fuses, power capcitor single phase preventor etc. complete set with supply of Jyoti or eq. Air break Star- Delta motro starter suitable for above submersible pump set.- BORING-17 |
| 438 | Supply of 80mm dia M.S. column pipe of class 'C' both and socketed with heavy sockets in 3/6 meter length and one end flanged complete with interlocking arrangements.- BORING-18 |
| 439 | Supply of 80mm dia M.S. column pipe clamps with nut, bolts, packing etc.- BORING-19 |
| 440 | Supply of 80mm dia C.I. double flanged ISI mark reflex valve of updadhya or equ. Make.- BORING-20 |
| 441 | Supply of 80mm dia C.I. double flanged ISI mark sluice valve with hand wheel of upadhya or equ. Make.- BORING-21 |
| 442 | Supply of C.I. double flanged bend of 80mm dia i/c cost of material and labour.- BORING-22 |
| 443 | Supply of 80mm dia C.I. tee heavy quality i/c cost of material.- BORING-23 |
| 444 | Supply of Guru/Fibing or equivalent make pressure gauge.- BORING-24 |
| 445 | Erection & commissioning of pumping plants complete along with electric wiring.- BORING-25 |
| 446 | Supply of steel wire rope of 1/2\\" size- BORING-26 |
| 447 | S/B of 600mm x 600 mm x 6.0 mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead on one no. 8 to 10 SWG GI wite in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. , pipe and G.I. wire will be extra) 30 cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal. coke and salt at least 150mm thick alround etc. as per directions of E/I complete in all respects as per drawing.- BORING-27 |
| 448 | S/F of one number 8 to 6 SWG G.I. wire in 15mm dia G.I. Pipe for earthing, laid in ground or in wall duly concealed includingn the cost of cement, sand labour. T&P other material required for proper completion of the work as directed at site.- BORING-28 |
| 449 | S/F of aluminium conductor PVC insulated armoured, served, sheathed cable 1100 volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by E/I complete in all respects The armoring of the cable shall be properly connected with the earth conductor by clamps etc.- BORING-29 |
| 450 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement, All works upto plinth level, Concrete of M30 grade with minimum cement content of 350 kg /cumDSR 2023- 5.33.1.2 |
| 451 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).DSR - 2020 (Horticulture)- 2.3 |
| 452 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :, Screened through sieve of I.S. designation 4.75 mmDSR - 2020 (Horticulture)- 2.4.3 |
| 453 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-chargeDSR - 2020 (Horticulture)- 2.9 |
| 454 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).DSR - 2020 (Horticulture)- 2.8 |
| 455 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately), Holes 1.2 m dia and 1.2 m deepDSR - 2020 (Horticulture)- 2.14.1 |
| 456 | Providing and stacking of Phoenix sylvestris Roxb. (Wild date palm/khajur) of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.DSR - 2020 (Horticulture)- 7.63 |
| 457 | Providing and stacking of Pinus longifolia (Pinus) of height 90-105 cm. in cement pots of size 35 cm as per direction of the officer-in-charge.DSR - 2020 (Horticulture)- 7.65 |
| 458 | Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 metre above ground level and 0.50 metre below ground level. The vertical members shall consist of four nos of angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint of approved brand and manufacture over a coat of primer, complete in all respect.DSR - 2020 (Horticulture)- 2.27 |
| 459 | Grassing with selection No. 1 Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for separately)., Grassing with selection No. 1 Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for separately). In rows 5 cm apart in both directionsDSR - 2020 (Horticulture)- 2.10.1 |
| 460 | Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.DSR 2023- 8.4 |
| 461 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :, \\"(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. DSR 22.7.1\\"DSR 2023- 22.7.1 |
| 462 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of WC. kitchen and the like consisting of 1) Ist course of applying cement slurry 4, 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface) IInd course of 20mm cement plaster 13 (1 cement 3 coarse sand) maxed with water proofing compound in recommended proportion mcluding rounding off junction of vertical and horizontal surface IIIrd course of applying blown or residual bitumen applied hot at 17 Kg per sqm of area iv) IVth course of 400 micron thick PVC sheet (Overlaps at jomts of PVC sheet should be 100 mm wide and pasted to cach other with bitumen 17 Kg/sqm)DSR 2023- 22.5 |
| 463 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).DSR 2023- 10.28 |
| 464 | Centering and shuttering including strutting, propping etc. and removal of form for :, Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and StrutsDSR 2023- 5.9.6 |
| 465 | Centering and shuttering including strutting, propping etc. and removal of form for :, Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thickDSR 2023- 5.9.21 |
| 466 | Centering and shuttering including strutting, propping etc. and removal of form for :, Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thickDSR 2023- 5.9.20 |
| 467 | Centering and shuttering including strutting, propping etc. and removal of form for :, Edges of slabs and breaks in floors and walls, Under 20 cm wideDSR 2023- 5.9.16.1 |
| 468 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement, All works above plinth level upto floor V level, Concrete of M25 grade with minimum cement content of 330 kg /cumDSR 2023- 5.33.2.1 |
| 469 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projectionsDSR 2023- 5.30 |
| 470 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :, 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)DSR 2023- 4.2.3 |
| 471 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :, Cement mortar 1:6 (1 cement : 6 coarse sand)DSR 2023- 6.4.2 |
| 472 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level., Cement mortar 1:4 (1 cement :4 coarse sand)DSR 2023- 6.13.2 |
| 473 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.ird course of half brick masonry.DSR 2023- 6.15 |
| 474 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :, 100 mm diameterDSR 2023- 19.1.1 |
| 475 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :, 100 mm diameter S.W. pipeDSR 2023- 19.2.1 |
| 476 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:, 150 x 100 mm size P type., With common burnt clay F.P.S. (non modular) bricks of class designation 7.5DSR 2023- 19.4.2.1 |
| 477 | 15 mm cement plaster on rough side of single or half brick wall of mix :, 1:6 (1 cement: 6 coarse sand)DSR 2023- 13.5.2 |
| 478 | 12 mm cement plaster of mix :, 1:6 (1 cement: 6 coarse sand)DSR 2023- 13.4.2 |
| 479 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.DSR 2023- 11.37 |
| 480 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.DSR 2023- 8.31 |
| 481 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:, New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)DSR 2023- 13.47.1 |
| 482 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour:, Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour: New work (two or more coats) over and including Water thinnable priming coat with cement primer having VOC content less than 50 gram/litre.DSR 2023- 13.41.1 |
| 483 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.DSR 2023- 13.80 |
| 484 | 20 mm cement plaster of mix :, 1:4 (1 cement: 4 coarse sand)DSR 2023- 13.6.1 |
| 485 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc., 15 mm nominal outer dia .Pipes.DSR 2023- 18.8.1 |
| 486 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc., 20 mm nominal outer dia .Pipes.DSR 2023- 18.8.2 |
| 487 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc., 25 mm nominal outer dia .Pipes.DSR 2023- 18.8.3 |
| 488 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc., 32 mm nominal outer dia .Pipes.DSR 2023- 18.8.4 |
| 489 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall., 20 mm dia. nominal boreDSR 2023- 18.10.2 |
| 490 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall., 25 mm dia. nominal boreDSR 2023- 18.10.3 |
| 491 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall., 32 mm dia. nominal boreDSR 2023- 18.10.4 |
| 492 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall., 40 mm dia. nominal boreDSR 2023- 18.10.5 |
| 493 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall., 50 mm dia. nominal boreDSR 2023- 18.10.6 |
| 494 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :, 25 mm nominal boreDSR 2023- 18.17.1 |
| 495 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :, 20 mm nominal bore. DSR 18.17.1ADSR 2023- 18.17.1A |
| 496 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :, 32 mm nominal bore.DSR 2023- 18.17.2 |
| 497 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :, 40 mm nominal boreDSR 2023- 18.17.3 |
| 498 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :, 50 mm nominal boreDSR 2023- 18.17.4 |
| 499 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :, 20 mm diameter pipeDSR 2023- 18.40.2 |
| 500 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :, 25 mm diameter pipeDSR 2023- 18.40.3 |
| 501 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :, 32 mm diameter pipeDSR 2023- 18.40.4 |
| 502 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :, 40 mm diameter pipeDSR 2023- 18.40.5 |
| 503 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :, 50 mm diameter pipeDSR 2023- 18.40.6 |
| 504 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work), 20 mm nominal boreDSR 2023- 18.46.2 |
| 505 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work), 25 mm nominal boreDSR 2023- 18.46.3 |
| 506 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work), 32 mm nominalDSR 2023- 18.46.4 |
| 507 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work), 40 mm nominal boreDSR 2023- 18.46.5 |
| 508 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work), 50mm nominal boreDSR 2023- 18.46.6 |
| 509 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :, 25 to 40 mm nominal boreDSR 2023- 18.13.1 |
| 510 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :, 50 to 80 mm nominal boreDSR 2023- 18.13.2 |
| 511 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball., 50mm nominal bore, 242 mm long. Weighing not less than 1240 gms.DSR 2023- 18.62.5 |
| 512 | FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL), Supplying, installation, testing & commissioning talk back slave station in surface/recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete asDSR 2025 E & M- 28.1.8 |
| 513 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) an, Two Loop Panel.DSR 2025 E & M- 28.2.1.2 |
| 514 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.DSR 2025 E & M- 28.2.4 |
| 515 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.DSR 2025 E & M- 28.2.5 |
| 516 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning of intelligent addressable programmable sounder complete as required.DSR 2025 E & M- 28.2.6 |
| 517 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning of fault isolator complete with base as required.DSR 2025 E & M- 28.2.7 |
| 518 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed temperature thermistor complete with base as required.DSR 2025 E & M- 28.2.9 |
| 519 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning addressable fire control module complete as required.DSR 2025 E & M- 28.2.10 |
| 520 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning addressable manual call point complete as required.DSR 2025 E & M- 28.2.14 |
| 521 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.DSR 2025 E & M- 28.2.17 |
| 522 | INTELLIGENT FIRE ALARM SYSTEM, Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.DSR 2025 E & M- 28.2.19 |
| 523 | CABLING & WIRING, Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS/HFFR outer sheath complete as required.DSR 2025 E & M- 28.5.2 |
| 524 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required., Group CDSR 2025 E & M- 1.10.3 |
| 525 | Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.DSR 2025 E & M- 1.11 |
| 526 | Wiring for light/ power plug with 2X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required.DSR 2025 E & M- 1.12 |
| 527 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required., 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wireDSR 2025 E & M- 1.14.2 |
| 528 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required., 2 X 6 sq. mm + 1 X 6 sq. mm earth wireDSR 2025 E & M- 1.14.4 |
| 529 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required., 4 X 6 sq. mm + 2 X 6 sq. mm earth wireDSR 2025 E & M- 1.14.9 |
| 530 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required., 4 X 16 sq. mm + 2 X 6 sq. mm earth wireDSR 2025 E & M- 1.14.11 |
| 531 | Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required., 2 PairDSR 2025 E & M- 1.18.2 |
| 532 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.DSR 2025 E & M- 1.19 |
| 533 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required., 25 mmDSR 2025 E & M- 1.21.2 |
| 534 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required., 5/6 A switchDSR 2025 E & M- 1.24.1 |
| 535 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required., 3 pin 5/6 A socket outletDSR 2025 E & M- 1.24.4 |
| 536 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required., Telephone socket outletDSR 2025 E & M- 1.24.6 |
| 537 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required., TV antenna socket outletDSR 2025 E & M- 1.24.7 |
| 538 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required., 1 or 2 Module (75mmX75mm)DSR 2025 E & M- 1.27.1 |
| 539 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.DSR 2025 E & M- 1.31 |
| 540 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.DSR 2025 E & M- 1.32 |
| 541 | Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required., Upto 450 mm sweepDSR 2025 E & M- 1.50.1 |
| 542 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required., Group CDSR 2025 E & M- 1.55.3 |
| 543 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).DSR 2025 E & M- 1.56 |
| 544 | Providing and mixing integral crystalline admixture for waterproofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc.. at the time of transporting of concrete into the drum of the ready-mix truck , using integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R- 2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.DSR 2023- 22.22 |
| 545 | (a) Supplying, installation, testing and commissioning of Electric driven Main Fire Pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required : (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required. (c) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-12615: 2018. (d) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (e)Suitable cement concrete foundation duly plastered with anti vibration pads., 2280 lpm at 70 m HeadDSR 2025 E & M- 27.1.5 |
| 546 | (a) Supplying, installation, testing and commissioning of diesel engine driven main fire pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) (b) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal as required., 2280 lpm at 70 m HeadDSR 2025 E & M- 27.2.5 |
| 547 | (a) Supplying, installation, testing and commissioning of electric driven pressurisation pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (b) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal as required. (c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, conforming to IS-12615: 2018., 180 lpm at 70 m HeadDSR 2025 E & M- 27.3.2 |
| 548 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :, 80 mm diaDSR 2025 E & M- 27.7.6 |
| 549 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :, 100 mm diaDSR 2025 E & M- 27.7.7 |
| 550 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :, 150 mm diaDSR 2025 E & M- 27.7.8 |
| 551 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :, 200 mm dia (wall thickness 6.3 mm)DSR 2025 E & M- 27.7.9 |
| 552 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :, 250 mm dia (wall thickness 6.3 mm)DSR 2025 E & M- 27.7.10 |
| 553 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :, Single headed GunmetalDSR 2025 E & M- 27.9.1 |
| 554 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :, 80 mm diaDSR 2025 E & M- 27.11.4 |
| 555 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :, 100 mm diaDSR 2025 E & M- 27.11.5 |
| 556 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :, 200 mm diaDSR 2025 E & M- 27.11.7 |
| 557 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.DSR 2025 E & M- 27.13 |
| 558 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :, 80mm diaDSR 2025 E & M- 27.14.4 |
| 559 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :, 100mm diaDSR 2025 E & M- 27.14.5 |
| 560 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :, 150mm diaDSR 2025 E & M- 27.14.7 |
| 561 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :, 200mm diaDSR 2025 E & M- 27.14.8 |
| 562 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange., 100mm diaDSR 2025 E & M- 27.15.2 |
| 563 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange., 200mm diaDSR 2025 E & M- 27.15.4 |
| 564 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :, Gun MetalDSR 2025 E & M- 27.16.1 |
| 565 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. (a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 (b) 20 mm nominal internal dia gun metal globe valve & nozzle. (c) Drum and brackets for fixing the equipmets on wall. (d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket., 40 mDSR 2025 E & M- 27.17.2 |
| 566 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:, Gun metalDSR 2025 E & M- 27.18.1 |
| 567 | Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.DSR 2025 E & M- 27.20 |
| 568 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.DSR 2025 E & M- 27.22 |
| 569 | Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required:, 150mm diaDSR 2025 E & M- 27.24.3 |
| 570 | Making khurras 45x45 cm with average minimum thickness of5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.DSR 2023- 12.22 |
| 571 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes., 110 mm diameterDSR 2023- 12.41.2 |
| 572 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Single pushfit Coupler :, 110mmDSR 2023- 12.42.2.2 |
| 573 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Single tee with door, 110x110x110 mmDSR 2023- 12.42.3.2 |
| 574 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Bend 87.5°, 110 mm bendDSR 2023- 12.42.5.2 |
| 575 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete., 110 mmDSR 2023- 12.43.2 |
| 576 | Providing and fixing PTMT grating of approved quality and colour., Rectangular type with openable circular lid., 150 mm nominal size square 100 mm diameter of the inner hinged round grating.DSR 2023- 18.58.2.1 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysDec 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender