Tender For Construction Of Minor Bridge, Approach Road, Additioal Approach Road And Protection Work Between Bishunpura Bajara And Suraji Tola At Seasonal Drain, Fy 2026-27
Tender Value
1.90 Crore
Estimated cost
Bid Submission
26 Nov 2026
9 days left
EMD
11.50 Lakhs
Bank guarantee accepted
Document Fee
2714
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Deoria → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Minor Bridge, Approach Road, Additioal Approach Road And Protection Work Between Bishunpura Bajara And Suraji Tola At Seasonal Drain, Fy 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material..Reference to MORT&H Specification 304 Sr No.15.01 |
| 2 | Granular sub-base in Foundation Trenches as per Drawing & Technical Specification. Reference to MORT&H Specification 304 Sr No.15.03 |
| 3 | Plain Cement Concrete M-15 in Open Foundation complete as per Drawing and Technical Specifications.Reference to MORT&H Specification1500, 1700 & 2100 Sr No.15.11 |
| 4 | Reinforced Cement Concrete (Grade M30) in Open Foundation complete as per Drawing and Technical Specifications. Reference to MORT&H Specification 1500, 1700 & 2100 Sr No.15.12 |
| 5 | Reinforced Cement Concrete (Grade M30) for wall & slab etc. complete as per Drawing and Technical Specifications..Reference to MORT&H Specification 1500, 1700 & 2100 Sr No.15.12 |
| 6 | Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation/Wall/Slab complete as per Drawing and Technical Specifications. Reference to MORT&H Specification 1600 Sr No.15.13 |
| 7 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications. Reference to MORT&H Specification 2706 & 2200 Sr No.15.14 |
| 8 | Drainage Spouts complete as per drawing and Technical specification. Reference to MORT&H Specification 2705 Sr No.15.17 |
| 9 | Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications Reference to MORT&H Specification 2702 Sr No.15.18 |
| 10 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical Specification Reference to MORT&H Specification710.1.4.of IRC:78 & 2200 Sr No.13.5 |
| 11 | Providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm. |
| 12 | Painting two coats after filling the surface with synthetic enamel paint bridge No. and span arrangements as per as directed by Engineer. |
| 13 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.1 and 300.2. with a lead upto 1000 m as per Technical Specification Clause 301.5 |
| 14 | Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per clause 401. |
| 15 | Providing, laying, WBM Grade-2 with 45-63mm size Stone Ballast, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled smooth roller 8-10 tonnes in stages to proper grade and camber, applying and brooming, stone screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per clause 405.2 (Including all taxes required & i/c hire charges of road roller) |
| 16 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per Technical Specification Clause 405. |
| 17 | Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including cleaning of road surface and spraying primer at the rate of 0.75 kg/sqm using mechanical means. As per Techinical specfication Clause 502 (Including all taxes required & including Cost of bitumen emulsion) |
| 18 | Providing and applying tack coat with Bitumen VG-10 using bitumen distributor at the rate of 0.30 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503. |
| 19 | Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. Case - I By Manual Means |
| 20 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 |
| 21 | Brick edging on both sides of the road of first class bricks 8 cm (3\\") wide and 12 cm. 4½\\"deep laid with mud mortar including labour and supply of. bricks finished to required template and proper alignment and also including dressing and ramming the excavated earth as directed by Engineer-in-Charge. |
| 22 | Construction of Subgrade and earhen shoulders with approved material obtained from borrow pits with all lift and lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2. with lead upto 1000 m as per Technical Specification Clause 301.1 |
| 23 | Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (as per Mord) |
| 24 | Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 (as per Mord) |
| 25 | Providing concrete for plain concrete M-10 in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (as per Mord) |
| 26 | Reinforced cement concrete M-25 in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (as per Mord) |
| 27 | Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202 (as per Mord) |
| 28 | Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (as per Mord) |
| 29 | Drainage spouts complete as per drawing and technical specifications Clause 1209 (as per Mord) |
| 30 | Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 (as per Mord) |
| 31 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical Specification Reference to MORT&H Specification710.1.4.of IRC:78 & 2200 Sr No.13.5 (as per Mord) |
| 32 | Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification. Reference to MORT&H Specification 2503 Sr No.16.01 |
| 33 | Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification. Reference to MORT&H Specification 2503 Sr No.16.01 |
| 34 | Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification Reference to MORT&H Specification 2504 Sr No.16.05 |
| 35 | Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications.Reference to MORT&H Specification 2504 Sr No.16.04 |
| 36 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. |
| 37 | Supply & fixing of pavement maker (Cat eye) type X-ASTMD-4956-04avery Dennison/3-M (USA make) consisting of ASA Plastic housing fitted with tightly adherent plotting compound The housaing shall contain prismatic tow glass covered prismatic reflective face to reflect incident light I/C all tax |
| 38 | Supplying and instalation of delinator (road way iddicators, hazard markers, object marker) 80-100 cm. high above ground level, painted black and white in 15 cm. wide strips. Fitted with 80x100mm rectangular or 75 mm dia cicular refiectionorised panel at the top buried or pressed into the ground and conforming to IRC:79 and the drawing. |
| 39 | Providing and erecting a \\"W\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender