Defence Statutory Bodies & Commissions/Committees Closing in 15 days TDR #58530309

Tender For Comprehensive B R Repairs In Otm Md Accn Of Ph I Area Under Ge Narangi

Issued by Statutory Bodies & Commissions/Committees · Kamrup Metro, Assam
Tender Value
25 Lakhs
Estimated cost
Bid Submission
04 Dec 2026
15 days left
EMD
50000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup Metro → Assam
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Comprehensive B R Repairs In Otm Md Accn Of Ph I Area Under Ge Narangi

BOQ

Name of Work:-
Sl. No. Item Description
1Taking down Shutters of any description exc 1 sq. m and n exc 2 sq. m each removing to store complete all as specified and as directed.
2Taking down Shutters of any description n exc 1 sq. m each removing to store complete all as specified and as directed.
3Taking down chowkats or frames with shutters (without taking off shutters from the frame) area n.exc. 1.5 Sqm including builders hardware each complete all as specified and as directed.
4Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each including builders hardware complete all as specified and as directed.
5Taking down shutter of any description exc 1 sqm but nexc 2 sqm each leaf and refixing in same opening complete all as specified and as directed.
6Hacking out old broken glass (any thickness, quality or description) from wooden frame or stone concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.
7Taking up or down GI tubing 15 mm bore from trenches/wall including all fittings segregated and stacking the pipe complete all as specified and directed.
8Taking up or down GI tubing 20 mm bore from trenches/wall including all fittings segregated and stacking the pipe complete all as specified and directed.
9Demolition of concrete in ground floors and pavings exc 15 cm thickness above ground level & also removing the debris to the out side of MD land complete all as specified and directed.
10Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed.
11Demolition of concrete in ground floors and pavings n exc 15 cm thickness ( below or above ground level) & also removing the debris to the out side of MD land
12Dismantling of stone slabs and tiles of andy description or thickness as on platform, shelves, floors etc laid, bedded and pointed in any mortar complete all as specified and directed.
13Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.
14Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.
15Taking down cement plaster/cement mud plaster on brick walls etc, incl racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.
16Dismantling of plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding etc., complete all as specified and directed.
17Material and labour for Plain cement concrete (1:3:6) type C 0 (using 12.5 mm graded crushed stone aggregate) as in back filling in pressed steel door and window frame complete all as specified and as directed.
18Supply only water proofing compound.
19Material and labour for cement concrete 1:3:6 type C-2 , (using 20 mm graded stone aggregate ) as in foundation filling and sunken floors etc complete all as specified and directed.
20Material and labour for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.
21Material and labour for brick work with sub class \\"B\\" bricks, straight or curved on plan exc to any radius in half brick thick walls built in built in CM 1:4 complete all as specifed and directed
22Material and labour 16-18 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite
23Material and labour Marble work 16 to 18mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrna Doogri/udaipur green over RCC slab including15 mm thick screed bed 1:4
24Supply and fix 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed
25Supply and fix 30mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc with plain, chamfered or rounded, mitred beads (with sash bars) for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (b) complete all as specified and directed.
26Supply and fix 35mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc.divided into squares, with plain,chamfered or rounded,mitred and rebated sash bars,any numbers, edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.
27Supply and fix 30 mm thcik flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.
28Supply and fix solid pre lam PVC door frame/CHOWKHAT of size 50mm x 45mm made out of 5mm PRELAM PVC sheet reinforced with M.S. square tube 15mm x 15mm. The two vertical door profiles are to be reinforced with 40mm x 20mm MS tube 19 guage. Door frame need to be fixed to wall using 100 mm long MS screws etc complete all as specified and as directed.
29Supply and fix factory made solid panel pre lam PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes 19 guage thickness and size of 40mm x 20 mm for stiles, top,bottom and lock rails. M.S. frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 30mm width stuck inside with solvent cement. 110 mm width forming stiles in which 100mmm should be flat and 5 mm should be tapered, and 5 mm thich, 135 mm wide prelam pvc sheet for top and bottom rail in wchich 125 should be flat and 5 mm should be tapered on either side of panel, also for lock rail 145 mm sheet, 125 should be flat and 5 mm tapered on either side. And additional 5 mm thich pvc strip struck inside of C channel. and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement etc complete all as specified and as directed.
30Material and labour for preparation of new or previously untreated surface of wood or wood based materials of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.
31Supply ands fix 100 mm size stainless steel butt hinges, complete all as specified and as directed.
32Supply ands fix 75 mm size stainless steel butt hinges, complete all as specified and as directed.
33Supply ands fix 150 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.
34Supply ands fix 100 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.
35Supply ands fix 150 mm extruded aluminum alloy handles, fabricated type, anodized complete all as specified and as directed
36Supply ands fix 125 mm extruded aluminum alloy handles, fabricated type, anodized complete all as specified and as directed
37Supply ands fix 300 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.
38Supply and fix in repair 20 mm dia D type CP towel rail 600 mm long between flanges complete all as specified and directed.
39Supply and fix in repairs 20 mm dia anodised aluminium tubular curtains rod complete all as specified and directed.
40Supply and fix in repair aluminium anodised brackets for curtain rod including end decorative piece complete all as specified and directed.
41Supply ands fix stain-less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples complete all as specified and as directed.
42Supply ands fix in repairs, stain-less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.
43Supply and fix pressed steel frames for doors of size 125mmx60mmx1.25mm with double rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and as directed.
44Supply and fix pressed steel frames for doors of size 105mmx60mmx1.25mm with single rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed
45Supply ands fix box type steel windows with side hung shutters both mosquito proof and glazed shutter including projecting type hinges with steel handle and steel peg stay with glazing bars and 12 mm square bar or ground bar of approved design welded to steel window frame dovetailed or welded complete all as specified and as directed.
46Supply ands fix steel ventilators with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.
47Supply and fix powder coated two track aluminium sliding window with approved make of following extruded section of anodised glazed shutter as per Standard Engineering practices including all other accessories complete including 4.00 mm thick tinted glass panes (Include of 02 Nos tinted glass window shutter with alu frame with frame ), rubber beading, locking system (Include of 03 Nos window shutter) etc. complete all as specified and as directed. (Refer Jindal Cat M-2014 ) Aluminium sections : 'A' series (i) Shutter bottom & top :- 37.50 x 15 x 1.3 mm thick (20690)(ii) Shutter interlock :- 37.50 x 23 x 1.3 mm thick (20689)(iii) Shutter side (Handle) :- 37.50 x 23 x 1.3 mm thick (20689) (iv) Frame bottom :- 75 x 26 x 1 mm thick (20671) (v) Frame top and sides :- 75 x 26 x 1 mm thick (20672)
48Supply and fix Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.
49Material and labour for rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St.-240 complete all as specified and as directed.
50Supply and fix pre-painted hot dip aluminium zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (total coated thickness), any patteren corresponding to IS 15965: 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour havingb yield strength of 550MPa as in roof covering/wall cladding, fixed with self tapping screws as complete all as specified and as directed.
51Supply and fix pre-painted hot dip aluminium zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (total coated thickness), any patteren corresponding to IS 15965: 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour havingb yield strength of 550MPa as in roof covering/wall cladding, fixed with self tapping screws as specified and as directedNote: To be executed for provison of ridges and hips, valley etc complete all as specifed and as directed
52Supply ands fix in repairs, suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 32 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement plain Board (E-Board Classic) in & including a grid of GI system duly suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and directed
53Material and labour for 50 mm dia and 350 mm long medium grade GI pipe spouts with wire gauge on inside mouth to be fixed before water proofing treatment of sunken slabs by cleaning RCC slab surface floors and walls by wire brush and rendering 6 mm thick in CM 1:4 mixed with integral WPC on uneven surface to make it even. Fill it water and check for dampness and seepage, all junctions points of side walls where CI/GI pipe are passing shall be sealed with epoxy mortar. Apply two coats of polymer modified cementious water proofing coating of minimum thickness of 1 mm each layer as per manufacturers instructions on floor & walls (upto 100 mm above FFL) and spray coarse sand on surface when the second layer is still sticky. Apply 20 mm thick plaster in CM 1:4 mixed with integral WPC of approved make on floors and walls including rounding of corners and junctions stoping towareds spouts. All pipes laid in sunken portions shall be covered with 50 mm thick PCC 1:3:6 all around after painting with anti corrosive black japan paint on GI/CI pipes. Test the water proofed area by filling water at least 72 hours and tested for leakage/seepage for the entire satisfaction of GE. After above said treatment apply two coats of hot blown bitumen @ 1.5 Kg /Sqm for each coat and laying 50 micron black polythene film in floors complete all as specified and directed. (Note : If leakage/Seepage occured after filling water at least 72 hours, the above said treatment will be re-done completely)
54Material and labour for 75 mm thick PCC 1:3:6, type C-1, (using 20 mm graded stone aggregates ) as in plinth protection ,hard standing etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade \\"A\\" complete all as specified and directed.
55Material and labour for 100mm thick PCC 1:2:4 type B2 (using 40mm graded stone aggregate) as in path/paving/hard standing and finishing the surfaces even and smooth without using exra cement complete all as specifed and directed
56Material and labour for 25 mm thick sub base PCC type B0 1:2:4, using 12.5 mm graded stone aggregate as in sub floor complete all as specified and directed.
57Material and labour for 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate in foundation, floor etc complete all as specified and directed.
58Material and labour for heavy duty parking tiles of size 300mm x 300mm x 10mm thick of approved make jointed in neat cement slurry, pointed in white or coloured cement to match colour of tiles over and including screed bed of 15 mm thick in cement mortar (1:4) complete all as specified and directed.
59Material and labour for non skid coloured ceramic tiles 7 to 8mm thick, (square/rectangular) area of each tiles exc 0.06 sqm but not exc 0.11 sqm as in floors set and jointed in cement slurry and pointed in white cement mixed with colour pigment to match existing surfaces with 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.
60Material and labour for non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.
61Material and labour for glazed light coloured/printed ceramic tiles 450x300x7mm thick in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match colour of tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.
62Material and labour for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed
63Material and labour for 15 mm thick rendering in cement mortar (1:4) on other than fair faces of brick work or concrete surfaces mixed with water proofing compound (@ 3% weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound to be measured and paid separately.
64Material and labour for rendering 5mm thick in cement mortar 1:3 on fair faces of brick/concrete surfces as in ceiling finished even and smooth without using extra cement.
65Material and labour for preparation of newly plastered or unplastered surface of ceiling and applying three coats of white wash complete all as specified and as directed.
66Material and labour for preparation of newly plastered surface of wall and applying a coat of alkali resistant primer and two coats of acrylic distemper complete all as specified and directed.
67Material and labour for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of primer complete all as specified and as directed.
68Material and labour for preparation of old decorated plastered surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc including cornices and pilasters etc and applying one coat of acrylic distemper incl filling the holes and cracks with white cement so that the surace will appear smooth finish complete all as specified and directed.
69Material and labour for preparation of old decorated wall surface and applying one coat of white wash complete all as specified and directed.
70Material and labour for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.
71Supply and fix sheet glass 3.0 mm thick ordinary quality and glazing with oil putty/wooden beads in squares not exc. 0.50sqm in each pane complete all as specified and directed.
72Supply and fix 4 mm thick figured glass pin head type and glazing with oil putty/wooden beads in squares not exc 0.5 sqm in each pane complete all as specified and directed .
73Material and labour for preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide complete all as specified and as directed.
74Material and labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed
75Material and labour for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed
76Material and labour for preparation of new steel surface of any description,exc 10cm width or girth and applying two coats synthetic enamel paint over a coat of zinc chrome primer complete all as specified and directed
77Supply and fix GI pipe medium grade 15mm bore fixed to wall wall and ceiling or laying in floors, with all new fittings as required at site complete
78Refixing old serviceable steel tubing 15 mm bore and connections in new or old position (walls, ceiling, floor etc) complete all as specified and directed.
79Supply and fix 20 mm bore galvanised iron tubing medium grade including all fittings in walls/ceilings or laid in floors including cutting complete all as specified and directed.
80Refixing old serviceable steel tubing 20 mm bore and connections in new or old position (walls, ceiling, floor etc) complete all as specified and directed.
81Cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc of capacity exc 500 ltr but n exc 1000 ltr and writing the date of cleaning on water tank with white paint complete all as specified and directed.
82Cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc of capacity up to 500 ltr and writing the date of cleaning on water tank with white paint complete all as specified and directed.
83Supply hoisting and fix 500 ltrs rotational moulded polythene water storage water tanks two layered construction ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I duly ISI Marked, 20mm GI light grade over flow pipe approx length 1.5m long, 20mm GI medium grade pipe for wash out approx length 2.00 m duly plugged at one end shall be provided including dismantling the existing tank complete all as specified.
84Supply hoisting and fix 1000 ltrs rotational moulded polythene water storage water tanks two layered construction ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I duly ISI Marked, 20mm GI light grade over flow pipe approx length 1.5m long, 20mm GI medium grade pipe for wash out approx length 2.00 m duly plugged at one end shall be provided including dismantling the existing tank complete all as specified.
85Supply and fix in repair chromium plated long body fancy type bib taps with wall flange, cast copper alloy with round operating knob screwed down high pressure, screwed for 15mm bore iron pipe complete all as specified and directed.
86Supply and fix in repair 15mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.
87Supply and fix in repair stop valves/angle cocks, cast copper alloy concealed type long body with round operating knob chromium plated screwed down high pressure, screwed both ends for 15 mm bore iron pipe or brass ferrule.
88Supply and fix in repair, 15mm bore dia of conceled stop valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.
89Supply and fix in repair stop valves or two way angle cocks, cast copper alloy concealed type long body with round operating knob chromium plated screwed down high pressure, screwed both ends for 15 mm bore iron pipe or brass ferrule.
90Supply and fix in repair 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and complete all as specified and directed.
91Supply and fix in repair 15mm bore PTMT Bib taps standard any colour screwed down for iron pipe and fixed minimum weight 90 gm complete all as specified and directed.
92Supply and fix in repairs chromium plated wall mixer three in one system for mixing hot and cold water with hand shower screwed down for iron pipe and fixed complete all as specified and as directed.
93Supply and fix in repair chromium plated centre hole wash basin mixer complete all as specified and as directed.
94Supply and fix in repair 20 mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210gms) complete all as specified and directed.
95Supply and fix in repair PTMT waste coupling of 32 mm dia (half or full thread) including taking down old coupling of any description complete all as specified and directed.
96All as per item No 95 here-in-before but 40 mm dia complete all as specified and directed.
97Supply and fix Stainless steel grating with hole 100 mm dia fix with cement all as specified and as directed
98Supply and fix Stainless steel grating without hole125 mm dia fix with cement all as specified and as directed
99Supply and fix in repair 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.
100Supply and fix in repair PVC connection pipe 15mm dia and 600 mm long with two PTMT nuts at each ends with rubber washer complete all as specified and directed.
101Supply and fix in repair CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed.
102Supply and fix in repair 125 mm dia, chromium plated swivel type shower rose with 195 mm long chromium plated shower arm and wall flange suitable for fixing 15mm bore iron pipe all as specified and directed
103Supply and fix in repairs 10 Litres, PVC valveless syphonic action type, flushing Cistern, low level, white inlet, ball valve, float, and brackets inclluding 32mm PVC flush pipe suitable for flushing cistern complete.
104Supply and fix in repairs 32/40mm dia flexible waste pipe for wash basin and kitchen sink complete all as specified and directed.
105Supply and fix 304 stainless steel sink with drainage board made of 1mm thick stainless steel sheet for kitchen with plugs, washers, waste coupling and pipe, cast iron cantilever brackets and connecting union to pipe overall size 940 mm x 460 mm bowl size 405mm x 354mm x 203mm complete all as specified and directed.
106Supply and fix in repair 204 stainless steel kitchen rack made of 0.85 mm thick stainless steel sheet of size 610 mm x 760 mm x 254 mm fixed to wall with screws complete all as specified and directed.
107Supply and fix in repair vitreous china squatting pan “Orissa pattern of size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including lime concrete bedding complete all as specified and directed.
108Supply and fix in repair vitreous china wash down water closet pan (Pedestal Pan) including fixing bolts, flush pipe anti syphonage pipe, plastic water closet seat , black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc, coloured closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed
109Supply and fix in repairs vitreous china wash basin, white , flat back , size 550 x400mm excluding taps, waste, chain and plug and porcelain stopper but including barckets complete all as specified and directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58530309
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 25 Lakhs
LAST DATE 04-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Comprehensive B R Repairs In Otm Md Accn Of Ph I Area Under Ge Narangi
Basic Detail
Tender No 8207/B/E8
Bidding Type Tender
Location
City Kamrup Metro
State Assam
Key Dates
Publish Date 14 Nov 2026
Submission Date 04 Dec 2026
Open Date 07 Dec 2026
Finance
Tender Value 25 Lakhs
Tender Fee 500
EMD 50000
Exemption Available
Document List
8207Tender.pdf
9971551e-0740-498b-a60a-70f754928bf8.html
BOQ_895943.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 14, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 04, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 15 days
Dec 07, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 18 days

Tender Documents

Download All (ZIP) ↓
pdf

8207Tender.pdf

html

9971551e-0740-498b-a60a-70f754928bf8.html

xls

BOQ_895943.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender